can: ti_hecc: convert block comments to network style comments

This patch converts all block comments to network subsystem style block
comments.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

diff --git a/drivers/net/can/ti_hecc.c b/drivers/net/can/ti_hecc.c
index b62f75f..0448b9a 100644 (file)
--- a/drivers/net/can/ti_hecc.c
+++ b/drivers/net/can/ti_hecc.c
@@ -46,8 +46,7 @@ MODULE_VERSION(HECC_MODULE_VERSION);
 #define HECC_MAX_MAILBOXES     32      /* hardware mailboxes - do not change */
 #define MAX_TX_PRIO            0x3F    /* hardware value - do not change */
 
-/*
- * Important Note: TX mailbox configuration
+/* Important Note: TX mailbox configuration
  * TX mailboxes should be restricted to the number of SKB buffers to avoid
  * maintaining SKB buffers separately. TX mailboxes should be a power of 2
  * for the mailbox logic to work.  Top mailbox numbers are reserved for RX
@@ -309,8 +308,7 @@ static void ti_hecc_reset(struct net_device *ndev)
        /* Set change control request and wait till enabled */
        hecc_set_bit(priv, HECC_CANMC, HECC_CANMC_CCR);
 
-       /*
-        * INFO: It has been observed that at times CCE bit may not be
+       /* INFO: It has been observed that at times CCE bit may not be
         * set and hw seems to be ok even if this bit is not set so
         * timing out with a timing of 1ms to respect the specs
         */
@@ -320,8 +318,7 @@ static void ti_hecc_reset(struct net_device *ndev)
                udelay(10);
        }
 
-       /*
-        * Note: On HECC, BTC can be programmed only in initialization mode, so
+       /* Note: On HECC, BTC can be programmed only in initialization mode, so
         * it is expected that the can bittiming parameters are set via ip
         * utility before the device is opened
         */
@@ -330,13 +327,11 @@ static void ti_hecc_reset(struct net_device *ndev)
        /* Clear CCR (and CANMC register) and wait for CCE = 0 enable */
        hecc_write(priv, HECC_CANMC, 0);
 
-       /*
-        * INFO: CAN net stack handles bus off and hence disabling auto-bus-on
+       /* INFO: CAN net stack handles bus off and hence disabling auto-bus-on
         * hecc_set_bit(priv, HECC_CANMC, HECC_CANMC_ABO);
         */
 
-       /*
-        * INFO: It has been observed that at times CCE bit may not be
+       /* INFO: It has been observed that at times CCE bit may not be
         * set and hw seems to be ok even if this bit is not set so
         */
        cnt = HECC_CCE_WAIT_COUNT;
@@ -439,8 +434,7 @@ static int ti_hecc_get_berr_counter(const struct net_device *ndev,
        return 0;
 }
 
-/*
- * ti_hecc_xmit: HECC Transmit
+/* ti_hecc_xmit: HECC Transmit
  *
  * The transmit mailboxes start from 0 to HECC_MAX_TX_MBOX. In HECC the
  * priority of the mailbox for tranmission is dependent upon priority setting
@@ -601,8 +595,7 @@ static int ti_hecc_error(struct net_device *ndev, int int_status,
                hecc_clear_bit(priv, HECC_CANMC, HECC_CANMC_CCR);
        }
 
-       /*
-        * Need to check busoff condition in error status register too to
+       /* Need to check busoff condition in error status register too to
         * ensure warning interrupts don't hog the system
         */
        if ((int_status & HECC_CANGIF_BOIF) || (err_status & HECC_CANES_BO)) {