--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Trogdor device tree source (common between revisions)
+ *
+ * Copyright 2019 Google LLC.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+/* PMICs depend on spmi_bus label and so must come after SoC */
+#include "pm6150.dtsi"
+#include "pm6150l.dtsi"
+
+/*
+ * Reserved memory changes
+ *
+ * Delete all unused memory nodes and define the peripheral memory regions
+ * required by the board dts.
+ */
+
+/delete-node/ &hyp_mem;
+/delete-node/ &xbl_mem;
+/delete-node/ &aop_mem;
+/delete-node/ &sec_apps_mem;
+/delete-node/ &tz_mem;
+
+/* Increase the size from 2MB to 8MB */
+&rmtfs_mem {
+ reg = <0x0 0x84400000 0x0 0x800000>;
+};
+
+/ {
+ reserved-memory {
+ atf_mem: memory@80b00000 {
+ reg = <0x0 0x80b00000 0x0 0x100000>;
+ no-map;
+ };
+
+ mpss_mem: memory@86000000 {
+ reg = <0x0 0x86000000 0x0 0x8c00000>;
+ no-map;
+ };
+
+ camera_mem: memory@8ec00000 {
+ reg = <0x0 0x8ec00000 0x0 0x500000>;
+ no-map;
+ };
+
+ venus_mem: memory@8f600000 {
+ reg = <0 0x8f600000 0 0x500000>;
+ no-map;
+ };
+
+ wlan_mem: memory@94100000 {
+ reg = <0x0 0x94100000 0x0 0x200000>;
+ no-map;
+ };
+
+ mba_mem: memory@94400000 {
+ reg = <0x0 0x94400000 0x0 0x200000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ bluetooth0 = &bluetooth;
+ hsuart0 = &uart3;
+ serial0 = &uart8;
+ wifi0 = &wifi;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ /* FIXED REGULATORS - parents above children */
+
+ /* This is the top level supply and variable voltage */
+ ppvar_sys: ppvar-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "ppvar_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ /* This divides ppvar_sys by 2, so voltage is variable */
+ src_vph_pwr: src-vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "src_vph_pwr";
+
+ /* EC turns on with switchcap_on; always on for AP */
+ regulator-always-on;
+ regulator-boot-on;
+
+ vin-supply = <&ppvar_sys>;
+ };
+
+ pp5000_a: pp5000-a-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "pp5000_a";
+
+ /* EC turns on with en_pp5000_a; always on for AP */
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ vin-supply = <&ppvar_sys>;
+ };
+
+ pp3300_a: pp3300-a-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "pp3300_a";
+
+ /* EC turns on with en_pp3300_a; always on for AP */
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ /*
+ * Actually should be pp3300 but that's practically an alias for
+ * pp3300_a so we use pp3300's vin-supply here to avoid one more
+ * node.
+ */
+ vin-supply = <&ppvar_sys>;
+ };
+
+ pp3300_audio:
+ pp3300_codec: pp3300-codec-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "pp3300_codec";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 83 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&en_pp3300_codec>;
+
+ vin-supply = <&pp3300_a>;
+ };
+
+ pp3300_dx_edp:
+ pp3300_ts: pp3300-dx-edp-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "pp3300_dx_edp";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 30 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&en_pp3300_dx_edp>;
+
+ vin-supply = <&pp3300_a>;
+ };
+
+ pp3300_fp_tp: pp3300-fp-tp-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "pp3300_fp_tp";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ /* AP turns on with PP1800_VIO_OUT; always on for AP */
+ regulator-always-on;
+ regulator-boot-on;
+
+ vin-supply = <&pp3300_a>;
+ };
+
+ /* BOARD-SPECIFIC TOP LEVEL NODES */
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+
+ pwms = <&cros_ec_pwm 1>;
+ enable-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+ power-supply = <&ppvar_sys>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ap_edp_bklten>;
+ };
+
+ gpio_keys: gpio-keys {
+ compatible = "gpio-keys";
+ status = "disabled";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pen_pdct_l>;
+
+ pen-insert {
+ label = "Pen Insert";
+
+ /* Insert = low, eject = high */
+ gpios = <&tlmm 52 GPIO_ACTIVE_LOW>;
+ linux,code = <SW_PEN_INSERTED>;
+ linux,input-type = <EV_SW>;
+ wakeup-source;
+ };
+ };
+
+ max98357a: audio-codec-0 {
+ compatible = "maxim,max98357a";
+ pinctrl-names = "default";
+ pinctrl-0 = <&_en>;
+ sdmode-gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>;
+ #sound-dai-cells = <0>;
+ };
+
+ pwmleds {
+ compatible = "pwm-leds";
+ keyboard_backlight: keyboard-backlight {
+ status = "disabled";
+ label = "cros_ec::kbd_backlight";
+ pwms = <&cros_ec_pwm 0>;
+ max-brightness = <1023>;
+ };
+ };
+};
+
+&qfprom {
+ vcc-supply = <&pp1800_l11a>;
+};
+
+&qspi {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+
+ /* TODO: Increase frequency after testing */
+ spi-max-frequency = <25000000>;
+ spi-tx-bus-width = <2>;
+ spi-rx-bus-width = <2>;
+ };
+};
+
+&apps_rsc {
+ pm6150-rpmh-regulators {
+ compatible = "qcom,pm6150-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vddpx_1:
+ vdd2:
+ pp1125_s1a: smps1 {
+ regulator-min-microvolt = <1128000>;
+ regulator-max-microvolt = <1128000>;
+ };
+
+ /*
+ * pp2040_s5a (smps5) and pp1056_s4a (smps4) are just
+ * inputs to other rails on AOP-managed PMICs on trogdor.
+ * The system is already configured to manage these rails
+ * automatically (enable when needed, adjust voltage for
+ * headroom) so we won't specify anything here.
+ *
+ * NOTE: though the rails have a voltage implied by their
+ * name, the automatic headroom calculation might not result
+ * in them being that voltage. ...and that's OK.
+ * Specifically the only point of these rails is to provide
+ * an input source for other rails and if we can satisify the
+ * needs of those other rails with a lower source voltage then
+ * we save power.
+ */
+
+ pp1200_l1a: ldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp1000_l2a: ldo2 {
+ regulator-min-microvolt = <944000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp1000_l3a: ldo3 {
+ regulator-min-microvolt = <968000>;
+ regulator-max-microvolt = <1064000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdd_qlink_lv:
+ vdd_qlink_lv_ck:
+ vdd_qusb_hs0_core:
+ vdd_ufs1_core:
+ vdda_mipi_csi0_0p9:
+ vdda_mipi_csi1_0p9:
+ vdda_mipi_csi2_0p9:
+ vdda_mipi_csi3_0p9:
+ vdda_mipi_dsi0_pll:
+ vdda_pll_cc_ebi01:
+ vdda_qrefs_0p9:
+ vdda_usb_ss_dp_core:
+ pp900_l4a: ldo4 {
+ regulator-min-microvolt = <824000>;
+ regulator-max-microvolt = <928000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp2700_l5a: ldo5 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2704000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ ebi0_cal:
+ ebi1_cal:
+ vddio_ck_ebi0:
+ vddio_ck_ebi1:
+ vddio_ebi0:
+ vddq:
+ pp600_l6a: ldo6 {
+ regulator-min-microvolt = <568000>;
+ regulator-max-microvolt = <648000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdd_cx_wlan:
+ pp800_l9a: ldo9 {
+ regulator-min-microvolt = <488000>;
+ regulator-max-microvolt = <800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdd1:
+ vddpx_3:
+ vddpx_7:
+ vio_in:
+ pp1800_l10a: ldo10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdd_qfprom:
+ vdda_apc1_cs_1p8:
+ vdda_qrefs_1p8:
+ vdda_qusb_hs0_1p8:
+ vddpx_11:
+ vreg_bb_clk:
+ pp1800_l11a: ldo11 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ mcp_vccq:
+ pp1800_l12a_r: ldo12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp1800_l13a: ldo13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp1800_prox:
+ pp1800_l14a: ldo14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp1800_alc5682:
+ pp1800_l15a: ldo15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp2700_l16a: ldo16 {
+ regulator-min-microvolt = <2496000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdda_qusb_hs0_3p1:
+ vdd_pdphy:
+ pp3100_l17a: ldo17 {
+ regulator-min-microvolt = <2920000>;
+ regulator-max-microvolt = <3232000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp1800_pen:
+ pp1800_l18a: ldo18 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ mcp_vcc:
+ pp2850_l19a: ldo19 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ pm6150l-rpmh-regulators {
+ compatible = "qcom,pm6150l-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ pp1300_s8c: smps8 {
+ regulator-min-microvolt = <1120000>;
+ regulator-max-microvolt = <1408000>;
+ };
+
+ pp1800_l1c: ldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdd_wcss_adc_dac:
+ pp1300_l2c: ldo2 {
+ regulator-min-microvolt = <1168000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp1200_brij:
+ vdd_ufs1_1p2:
+ vdda_csi0_1p25:
+ vdda_csi1_1p25:
+ vdda_csi2_1p25:
+ vdda_csi3_1p25:
+ vdda_hv_ebi0:
+ vdda_mipi_dsi0_1p2:
+ vdda_usb_ss_dp_1p2:
+ vddpx_10:
+ pp1200_l3c: ldo3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ ld_pp1800_esim_l4c:
+ vddpx_5:
+ pp1800_l4c: ldo4 {
+ regulator-min-microvolt = <1648000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vddpx_6:
+ pp1800_l5c: ldo5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vddpx_2:
+ ppvar_l6c: ldo6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp3300_hub:
+ pp3300_l7c: ldo7 {
+ regulator-min-microvolt = <3304000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ pp1800_brij_vccio:
+ pp1800_edp_vpll:
+ pp1800_l8c: ldo8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp2950_l9c: ldo9 {
+ regulator-min-microvolt = <2952000>;
+ regulator-max-microvolt = <2952000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp3300_l10c: ldo10 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ pp3300_l11c: ldo11 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ src_vreg_bob: bob {
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+ };
+ };
+};
+
+&ap_ec_spi {
+ status = "okay";
+ cros_ec: ec@0 {
+ compatible = "google,cros-ec-spi";
+ reg = <0>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <94 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ap_ec_int_l>;
+ spi-max-frequency = <3000000>;
+
+ cros_ec_pwm: ec-pwm {
+ compatible = "google,cros-ec-pwm";
+ #pwm-cells = <1>;
+ };
+
+ i2c_tunnel: i2c-tunnel {
+ compatible = "google,cros-ec-i2c-tunnel";
+ google,remote-bus = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ pdupdate {
+ compatible = "google,cros-ec-pd-update";
+ };
+
+ typec {
+ compatible = "google,cros-ec-typec";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ label = "left";
+ power-role = "dual";
+ data-role = "host";
+ try-power-role = "source";
+ };
+
+ connector@1 {
+ compatible = "usb-c-connector";
+ reg = <1>;
+ label = "right";
+ power-role = "dual";
+ data-role = "host";
+ try-power-role = "source";
+ };
+ };
+ };
+};
+
+&ap_h1_spi {
+ status = "okay";
+ cr50: tpm@0 {
+ compatible = "google,cr50";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&h1_ap_int_odl>;
+ spi-max-frequency = <800000>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <42 IRQ_TYPE_EDGE_RISING>;
+ };
+};
+
+&dsi0 {
+ status = "okay";
+ vdda-supply = <&vdda_mipi_dsi0_1p2>;
+
+ ports {
+ port@1 {
+ endpoint {
+ remote-endpoint = <&sn65dsi86_in>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };
+};
+
+&dsi_phy {
+ status = "okay";
+ vdds-supply = <&vdda_mipi_dsi0_pll>;
+};
+
+edp_brij_i2c: &i2c2 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ sn65dsi86_bridge: bridge@2d {
+ compatible = "ti,sn65dsi86";
+ reg = <0x2d>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_brij_en>, <&edp_brij_irq>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+
+ enable-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>;
+
+ vpll-supply = <&pp1800_edp_vpll>;
+ vccio-supply = <&pp1800_brij_vccio>;
+ vcca-supply = <&pp1200_brij>;
+ vcc-supply = <&pp1200_brij>;
+
+ clocks = <&rpmhcc RPMH_LN_BB_CLK3>;
+ clock-names = "refclk";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ sn65dsi86_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ sn65dsi86_out: endpoint {
+ data-lanes = <0 1>;
+ remote-endpoint = <&panel_in_edp>;
+ };
+ };
+ };
+ };
+};
+
+ap_sar_sensor_i2c: &i2c5 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ ap_sar_sensor: proximity@28 {
+ compatible = "semtech,sx9310";
+ reg = <0x28>;
+ #io-channel-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&p_sensor_int_l>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+
+ vdd-supply = <&pp3300_a>;
+ svdd-supply = <&pp1800_prox>;
+
+ status = "disabled";
+ label = "proximity-wifi";
+ };
+};
+
+ap_tp_i2c: &i2c7 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ trackpad@15 {
+ compatible = "elan,ekth3000";
+ reg = <0x15>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&trackpad_int_1v8_odl>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <58 IRQ_TYPE_EDGE_FALLING>;
+
+ vcc-supply = <&pp3300_fp_tp>;
+
+ wakeup-source;
+ };
+};
+
+hp_i2c: &i2c9 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ alc5682: codec@1a {
+ compatible = "realtek,rt5682i";
+ reg = <0x1a>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hp_irq>;
+
+ #sound-dai-cells = <1>;
+
+ interrupt-parent = <&tlmm>;
+ /*
+ * This will get ignored because the interrupt type
+ * is set in rt5682.c.
+ */
+ interrupts = <28 IRQ_TYPE_EDGE_BOTH>;
+
+ AVDD-supply = <&pp1800_alc5682>;
+ MICVDD-supply = <&pp3300_codec>;
+ VBAT-supply = <&pp3300_audio>;
+
+ realtek,dmic1-data-pin = <1>;
+ realtek,dmic1-clk-pin = <1>;
+ realtek,jd-src = <1>;
+ };
+};
+
+&ipa {
+ status = "okay";
+
+ /*
+ * Trogdor doesn't have QHEE (Qualcomm's EL2 blob), so the
+ * modem needs to cover certain init steps (GSI init), and
+ * the AP needs to wait for it.
+ */
+ modem-init;
+};
+
+&mdp {
+ status = "okay";
+};
+
+&mdss {
+ status = "okay";
+};
+
+&pm6150_pwrkey {
+ status = "disabled";
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&remoteproc_mpss {
+ status = "okay";
+ compatible = "qcom,sc7180-mss-pil";
+ iommus = <&apps_smmu 0x461 0x0>, <&apps_smmu 0x444 0x3>;
+ memory-region = <&mba_mem &mpss_mem>;
+
+ /* This gets overridden for SKUs with LTE support. */
+ firmware-name = "qcom/sc7180-trogdor/modem-nolte/mba.mbn",
+ "qcom/sc7180-trogdor/modem-nolte/qdsp6sw.mbn";
+};
+
+&sdhc_1 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_on>;
+ pinctrl-1 = <&sdc1_off>;
+ vmmc-supply = <&mcp_vcc>;
+ vqmmc-supply = <&mcp_vccq>;
+};
+
+&sdhc_2 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_on>;
+ pinctrl-1 = <&sdc2_off>;
+ vmmc-supply = <&pp2950_l9c>;
+ vqmmc-supply = <&ppvar_l6c>;
+
+ cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>;
+};
+
+ap_spi_fp: &spi10 {
+ cros_ec_fp: ec@0 {
+ compatible = "google,cros-ec-spi";
+ reg = <0>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&fp_to_ap_irq_l>, <&fp_rst_l>, <&fpmcu_boot0>, <&fpmcu_sel>;
+ spi-max-frequency = <3000000>;
+ };
+};
+
+#include <arm/cros-ec-keyboard.dtsi>
+#include <arm/cros-ec-sbs.dtsi>
+
+&uart3 {
+ status = "okay";
+
+ bluetooth: bluetooth {
+ compatible = "qcom,wcn3991-bt";
+ vddio-supply = <&pp1800_l10a>;
+ vddxo-supply = <&pp1800_l1c>;
+ vddrf-supply = <&pp1300_l2c>;
+ vddch0-supply = <&pp3300_l10c>;
+ max-speed = <3200000>;
+ clocks = <&rpmhcc RPMH_RF_CLK2>;
+ };
+};
+
+&uart8 {
+ status = "okay";
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_1_hsphy {
+ status = "okay";
+ vdd-supply = <&vdd_qusb_hs0_core>;
+ vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
+ vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
+ qcom,imp-res-offset-value = <8>;
+ qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>;
+ qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+ qcom,bias-ctrl-value = <0x22>;
+ qcom,charge-ctrl-value = <3>;
+ qcom,hsdisc-trim-value = <0>;
+};
+
+&usb_1_qmpphy {
+ status = "okay";
+ vdda-phy-supply = <&vdda_usb_ss_dp_1p2>;
+ vdda-pll-supply = <&vdda_usb_ss_dp_core>;
+};
+
+&venus {
+ video-firmware {
+ iommus = <&apps_smmu 0x0c42 0x0>;
+ };
+};
+
+&wifi {
+ status = "okay";
+ vdd-0.8-cx-mx-supply = <&vdd_cx_wlan>;
+ vdd-1.8-xo-supply = <&pp1800_l1c>;
+ vdd-1.3-rfa-supply = <&pp1300_l2c>;
+ vdd-3.3-ch0-supply = <&pp3300_l10c>;
+ vdd-3.3-ch1-supply = <&pp3300_l11c>;
+
+ wifi-firmware {
+ iommus = <&apps_smmu 0xc2 0x1>;
+ };
+};
+
+/* PINCTRL - additions to nodes defined in sc7180.dtsi */
+
+&qspi_cs0 {
+ pinconf {
+ pins = "gpio68";
+ bias-disable;
+ };
+};
+
+&qspi_clk {
+ pinconf {
+ pins = "gpio63";
+ bias-disable;
+ };
+};
+
+&qspi_data01 {
+ pinconf {
+ pins = "gpio64", "gpio65";
+
+ /* High-Z when no transfers; nice to park the lines */
+ bias-pull-up;
+ };
+};
+
+&qup_i2c2_default {
+ pinconf {
+ pins = "gpio15", "gpio16";
+ drive-strength = <2>;
+
+ /* Has external pullup */
+ bias-disable;
+ };
+};
+
+&qup_i2c4_default {
+ pinconf {
+ pins = "gpio115", "gpio116";
+ drive-strength = <2>;
+
+ /* Has external pullup */
+ bias-disable;
+ };
+};
+
+&qup_i2c5_default {
+ pinconf {
+ pins = "gpio25", "gpio26";
+ drive-strength = <2>;
+
+ /* Has external pullup */
+ bias-disable;
+ };
+};
+
+&qup_i2c7_default {
+ pinconf {
+ pins = "gpio6", "gpio7";
+ drive-strength = <2>;
+
+ /* Has external pullup */
+ bias-disable;
+ };
+};
+
+&qup_i2c9_default {
+ pinconf {
+ pins = "gpio46", "gpio47";
+ drive-strength = <2>;
+
+ /* Has external pullup */
+ bias-disable;
+ };
+};
+
+&qup_spi0_default {
+ pinconf {
+ pins = "gpio34", "gpio35", "gpio36", "gpio37";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&qup_spi6_default {
+ pinconf {
+ pins = "gpio59", "gpio60", "gpio61", "gpio62";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&qup_spi10_default {
+ pinconf {
+ pins = "gpio86", "gpio87", "gpio88", "gpio89";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&qup_uart3_default {
+ pinconf-cts {
+ /*
+ * Configure a pull-down on CTS to match the pull of
+ * the Bluetooth module.
+ */
+ pins = "gpio38";
+ bias-pull-down;
+ };
+
+ pinconf-rts-tx {
+ /* We'll drive RTS and TX, so no pull */
+ pins = "gpio39", "gpio40";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pinconf-rx {
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module is
+ * in tri-state (module powered off or not driving the
+ * signal yet).
+ */
+ pins = "gpio41";
+ bias-pull-up;
+ };
+};
+
+&qup_uart8_default {
+ pinconf-tx {
+ pins = "gpio44";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pinconf-rx {
+ pins = "gpio45";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+};
+
+/* PINCTRL - board-specific pinctrl */
+
+&pm6150_gpio {
+ status = "disabled"; /* No GPIOs are connected */
+};
+
+&pm6150l_gpio {
+ gpio-line-names = "AP_SUSPEND",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "";
+};
+
+&tlmm {
+ /*
+ * pinctrl settings for pins that have no real owners.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&bios_flash_wp_l>, <&ap_suspend_l_neuter>;
+
+ amp_en: amp-en {
+ pinmux {
+ pins = "gpio23";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio23";
+ bias-pull-down;
+ };
+ };
+
+ ap_ec_int_l: ap-ec-int-l {
+ pinmux {
+ pins = "gpio94";
+ function = "gpio";
+ input-enable;
+ };
+
+ pinconf {
+ pins = "gpio94";
+ bias-pull-up;
+ };
+ };
+
+ ap_edp_bklten: ap-edp-bklten {
+ pinmux {
+ pins = "gpio12";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+
+ /* Force backlight to be disabled to match state at boot. */
+ output-low;
+ };
+ };
+
+ ap_suspend_l_neuter: ap-suspend-l-neuter {
+ pinmux {
+ pins = "gpio27";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio27";
+ bias-disable;
+ };
+ };
+
+ bios_flash_wp_l: bios-flash-wp-l {
+ pinmux {
+ pins = "gpio66";
+ function = "gpio";
+ input-enable;
+ };
+
+ pinconf {
+ pins = "gpio66";
+ bias-disable;
+ };
+ };
+
+ dp_hot_plug_det: dp-hot-plug-det {
+ pinmux {
+ pins = "gpio117";
+ function = "dp_hot";
+ };
+
+ config {
+ pins = "gpio117";
+ bias-disable;
+ input-enable;
+ drive-strength = <2>;
+ };
+ };
+
+ edp_brij_en: edp-brij-en {
+ pinmux {
+ pins = "gpio104";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio104";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ edp_brij_irq: edp-brij-irq {
+ pinmux {
+ pins = "gpio11";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio11";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ en_pp3300_codec: en-pp3300-codec {
+ pinmux {
+ pins = "gpio83";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio83";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ en_pp3300_dx_edp: en-pp3300-dx-edp {
+ pinmux {
+ pins = "gpio30";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio30";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ fpmcu_boot0: fpmcu-boot0 {
+ pinmux {
+ pins = "gpio10";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio10";
+ bias-disable;
+ drive-strength = <2>;
+ output-low;
+ };
+ };
+
+ fpmcu_sel: fpmcu-sel {
+ pinmux {
+ pins = "gpio22";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio22";
+ bias-disable;
+ drive-strength = <2>;
+ output-high;
+ };
+ };
+
+ fp_rst_l: fp-rst-l {
+ pinmux {
+ pins = "gpio5";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio5";
+ bias-disable;
+ drive-strength = <2>;
+ output-high;
+ };
+ };
+
+ fp_to_ap_irq_l: fp-to-ap-irq-l {
+ pinmux {
+ pins = "gpio4";
+ function = "gpio";
+ input-enable;
+ };
+
+ pinconf {
+ pins = "gpio4";
+
+ /* Has external pullup */
+ bias-disable;
+ };
+ };
+
+
+ h1_ap_int_odl: h1-ap-int-odl {
+ pinmux {
+ pins = "gpio42";
+ function = "gpio";
+ input-enable;
+ };
+
+ pinconf {
+ pins = "gpio42";
+ bias-pull-up;
+ };
+ };
+
+ hp_irq: hp-irq {
+ pinmux {
+ pins = "gpio28";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio28";
+ bias-pull-up;
+ };
+ };
+
+ pen_irq_l: pen-irq-l {
+ pinmux {
+ pins = "gpio21";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio21";
+
+ /* Has external pullup */
+ bias-disable;
+ };
+ };
+
+ pen_pdct_l: pen-pdct-l {
+ pinmux {
+ pins = "gpio52";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio52";
+
+ /* Has external pullup */
+ bias-disable;
+ };
+ };
+
+ pen_rst_odl: pen-rst-odl {
+ pinmux {
+ pins = "gpio18";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio18";
+ bias-disable;
+ drive-strength = <2>;
+
+ /*
+ * The pen driver doesn't currently support
+ * driving this reset line. By specifying
+ * output-high here we're relying on the fact
+ * that this pin has a default pulldown at boot
+ * (which makes sure the pen was in reset if it
+ * was powered) and then we set it high here to
+ * take it out of reset. Better would be if the
+ * pen driver could control this and we could
+ * remove "output-high" here.
+ */
+ output-high; /* TODO: Remove this? */
+ };
+ };
+
+ p_sensor_int_l: p-sensor-int-l {
+ pinmux {
+ pins = "gpio24";
+ function = "gpio";
+ input-enable;
+ };
+
+ pinconf {
+ pins = "gpio24";
+ bias-pull-up;
+ };
+ };
+
+ trackpad_int_1v8_odl: trackpad-int-1v8-odl {
+ pinmux {
+ pins = "gpio58";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio58";
+
+ /* Has external pullup */
+ bias-disable;
+ };
+ };
+
+ ts_int_l: ts-int-l {
+ pinmux {
+ pins = "gpio9";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio9";
+ bias-pull-up;
+ };
+ };
+
+ ts_reset_l: ts-reset-l {
+ pinmux {
+ pins = "gpio8";
+ function = "gpio";
+ };
+
+ pinconf {
+ pins = "gpio8";
+ bias-disable;
+ drive-strength = <2>;
+ };
+ };
+};
projects / linux-2.6-microblaze.git / commitdiff