+++ /dev/null
-#!/bin/bash
-# SPDX-License-Identifier: GPL-2.0
-#
-# This test sends 1Gbps of traffic through the switch, into which it then
-# injects a burst of traffic and tests that there are no drops.
-#
-# The 1Gbps stream is created by sending >1Gbps stream from H1. This stream
-# ingresses through $swp1, and is forwarded thtrough a small temporary pool to a
-# 1Gbps $swp3.
-#
-# Thus a 1Gbps stream enters $swp4, and is forwarded through a large pool to
-# $swp2, and eventually to H2. Since $swp2 is a 1Gbps port as well, no backlog
-# is generated.
-#
-# At this point, a burst of traffic is forwarded from H3. This enters $swp5, is
-# forwarded to $swp2, which is fully subscribed by the 1Gbps stream. The
-# expectation is that the burst is wholly absorbed by the large pool and no
-# drops are caused. After the burst, there should be a backlog that is hard to
-# get rid of, because $sw2 is fully subscribed. But because each individual
-# packet is scheduled soon after getting enqueued, SLL and HLL do not impact the
-# test.
-#
-# +-----------------------+ +-----------------------+
-# | H1 | | H3 |
-# | + $h1.111 | | $h3.111 + |
-# | | 192.0.2.33/28 | | 192.0.2.35/28 | |
-# | | | | | |
-# | + $h1 | | $h3 + |
-# +---|-------------------+ +--------------------+ +------------------|----+
-# | | | |
-# +---|----------------------|--------------------|----------------------|----+
-# | + $swp1 $swp3 + + $swp4 $swp5 | |
-# | | iPOOL1 iPOOL0 | | iPOOL2 iPOOL2 | |
-# | | ePOOL4 ePOOL5 | | ePOOL4 ePOOL4 | |
-# | | 1Gbps | | 1Gbps | |
-# | +-|----------------------|-+ +-|----------------------|-+ |
-# | | + $swp1.111 $swp3.111 + | | + $swp4.111 $swp5.111 + | |
-# | | | | | |
-# | | BR1 | | BR2 | |
-# | | | | | |
-# | | | | + $swp2.111 | |
-# | +--------------------------+ +---------|----------------+ |
-# | | |
-# | iPOOL0: 500KB dynamic | |
-# | iPOOL1: 500KB dynamic | |
-# | iPOOL2: 10MB dynamic + $swp2 |
-# | ePOOL4: 500KB dynamic | iPOOL0 |
-# | ePOOL5: 500KB dnamic | ePOOL6 |
-# | ePOOL6: 10MB dynamic | 1Gbps |
-# +-------------------------------------------------------|-------------------+
-# |
-# +---|-------------------+
-# | + $h2 H2 |
-# | | 1Gbps |
-# | | |
-# | + $h2.111 |
-# | 192.0.2.34/28 |
-# +-----------------------+
-#
-# iPOOL0+ePOOL4 are helper pools for control traffic etc.
-# iPOOL1+ePOOL5 are helper pools for modeling the 1Gbps stream
-# iPOOL2+ePOOL6 are pools for soaking the burst traffic
-
-ALL_TESTS="
- ping_ipv4
- test_8K
- test_800
-"
-
-lib_dir=$(dirname $0)/../../../net/forwarding
-
-NUM_NETIFS=8
-source $lib_dir/lib.sh
-source $lib_dir/devlink_lib.sh
-source qos_lib.sh
-source mlxsw_lib.sh
-
-_1KB=1000
-_500KB=$((500 * _1KB))
-_1MB=$((1000 * _1KB))
-
-# The failure mode that this specifically tests is exhaustion of descriptor
-# buffer. The point is to produce a burst that shared buffer should be able
-# to accommodate, but produce it with small enough packets that the machine
-# runs out of the descriptor buffer space with default configuration.
-#
-# The machine therefore needs to be able to produce line rate with as small
-# packets as possible, and at the same time have large enough buffer that
-# when filled with these small packets, it runs out of descriptors.
-# Spectrum-2 is very close, but cannot perform this test. Therefore use
-# Spectrum-3 as a minimum, and permit larger burst size, and therefore
-# larger packets, to reduce spurious failures.
-#
-mlxsw_only_on_spectrum 3+ || exit
-
-BURST_SIZE=$((50000000))
-POOL_SIZE=$BURST_SIZE
-
-h1_create()
-{
- simple_if_init $h1
- mtu_set $h1 10000
-
- vlan_create $h1 111 v$h1 192.0.2.33/28
- ip link set dev $h1.111 type vlan egress-qos-map 0:1
-}
-
-h1_destroy()
-{
- vlan_destroy $h1 111
-
- mtu_restore $h1
- simple_if_fini $h1
-}
-
-h2_create()
-{
- simple_if_init $h2
- mtu_set $h2 10000
- ethtool -s $h2 speed 1000 autoneg off
-
- vlan_create $h2 111 v$h2 192.0.2.34/28
-}
-
-h2_destroy()
-{
- vlan_destroy $h2 111
-
- ethtool -s $h2 autoneg on
- mtu_restore $h2
- simple_if_fini $h2
-}
-
-h3_create()
-{
- simple_if_init $h3
- mtu_set $h3 10000
-
- vlan_create $h3 111 v$h3 192.0.2.35/28
-}
-
-h3_destroy()
-{
- vlan_destroy $h3 111
-
- mtu_restore $h3
- simple_if_fini $h3
-}
-
-switch_create()
-{
- # pools
- # -----
-
- devlink_pool_size_thtype_save 0
- devlink_pool_size_thtype_save 4
- devlink_pool_size_thtype_save 1
- devlink_pool_size_thtype_save 5
- devlink_pool_size_thtype_save 2
- devlink_pool_size_thtype_save 6
-
- devlink_port_pool_th_save $swp1 1
- devlink_port_pool_th_save $swp2 6
- devlink_port_pool_th_save $swp3 5
- devlink_port_pool_th_save $swp4 2
- devlink_port_pool_th_save $swp5 2
-
- devlink_tc_bind_pool_th_save $swp1 1 ingress
- devlink_tc_bind_pool_th_save $swp2 1 egress
- devlink_tc_bind_pool_th_save $swp3 1 egress
- devlink_tc_bind_pool_th_save $swp4 1 ingress
- devlink_tc_bind_pool_th_save $swp5 1 ingress
-
- # Control traffic pools. Just reduce the size.
- devlink_pool_size_thtype_set 0 dynamic $_500KB
- devlink_pool_size_thtype_set 4 dynamic $_500KB
-
- # Stream modeling pools.
- devlink_pool_size_thtype_set 1 dynamic $_500KB
- devlink_pool_size_thtype_set 5 dynamic $_500KB
-
- # Burst soak pools.
- devlink_pool_size_thtype_set 2 static $POOL_SIZE
- devlink_pool_size_thtype_set 6 static $POOL_SIZE
-
- # $swp1
- # -----
-
- ip link set dev $swp1 up
- mtu_set $swp1 10000
- vlan_create $swp1 111
- ip link set dev $swp1.111 type vlan ingress-qos-map 0:0 1:1
-
- devlink_port_pool_th_set $swp1 1 16
- devlink_tc_bind_pool_th_set $swp1 1 ingress 1 16
-
- # Configure qdisc...
- tc qdisc replace dev $swp1 root handle 1: \
- ets bands 8 strict 8 priomap 7 6
- # ... so that we can assign prio1 traffic to PG1.
- dcb buffer set dev $swp1 prio-buffer all:0 1:1
-
- # $swp2
- # -----
-
- ip link set dev $swp2 up
- mtu_set $swp2 10000
- ethtool -s $swp2 speed 1000 autoneg off
- vlan_create $swp2 111
- ip link set dev $swp2.111 type vlan egress-qos-map 0:0 1:1
-
- devlink_port_pool_th_set $swp2 6 $POOL_SIZE
- devlink_tc_bind_pool_th_set $swp2 1 egress 6 $POOL_SIZE
-
- # prio 0->TC0 (band 7), 1->TC1 (band 6)
- tc qdisc replace dev $swp2 root handle 1: \
- ets bands 8 strict 8 priomap 7 6
-
- # $swp3
- # -----
-
- ip link set dev $swp3 up
- mtu_set $swp3 10000
- ethtool -s $swp3 speed 1000 autoneg off
- vlan_create $swp3 111
- ip link set dev $swp3.111 type vlan egress-qos-map 0:0 1:1
-
- devlink_port_pool_th_set $swp3 5 16
- devlink_tc_bind_pool_th_set $swp3 1 egress 5 16
-
- # prio 0->TC0 (band 7), 1->TC1 (band 6)
- tc qdisc replace dev $swp3 root handle 1: \
- ets bands 8 strict 8 priomap 7 6
-
- # $swp4
- # -----
-
- ip link set dev $swp4 up
- mtu_set $swp4 10000
- ethtool -s $swp4 speed 1000 autoneg off
- vlan_create $swp4 111
- ip link set dev $swp4.111 type vlan ingress-qos-map 0:0 1:1
-
- devlink_port_pool_th_set $swp4 2 $POOL_SIZE
- devlink_tc_bind_pool_th_set $swp4 1 ingress 2 $POOL_SIZE
-
- # Configure qdisc...
- tc qdisc replace dev $swp4 root handle 1: \
- ets bands 8 strict 8 priomap 7 6
- # ... so that we can assign prio1 traffic to PG1.
- dcb buffer set dev $swp4 prio-buffer all:0 1:1
-
- # $swp5
- # -----
-
- ip link set dev $swp5 up
- mtu_set $swp5 10000
- vlan_create $swp5 111
- ip link set dev $swp5.111 type vlan ingress-qos-map 0:0 1:1
-
- devlink_port_pool_th_set $swp5 2 $POOL_SIZE
- devlink_tc_bind_pool_th_set $swp5 1 ingress 2 $POOL_SIZE
-
- # Configure qdisc...
- tc qdisc replace dev $swp5 root handle 1: \
- ets bands 8 strict 8 priomap 7 6
- # ... so that we can assign prio1 traffic to PG1.
- dcb buffer set dev $swp5 prio-buffer all:0 1:1
-
- # bridges
- # -------
-
- ip link add name br1 type bridge vlan_filtering 0
- ip link set dev $swp1.111 master br1
- ip link set dev $swp3.111 master br1
- ip link set dev br1 up
-
- ip link add name br2 type bridge vlan_filtering 0
- ip link set dev $swp2.111 master br2
- ip link set dev $swp4.111 master br2
- ip link set dev $swp5.111 master br2
- ip link set dev br2 up
-}
-
-switch_destroy()
-{
- # Do this first so that we can reset the limits to values that are only
- # valid for the original static / dynamic setting.
- devlink_pool_size_thtype_restore 6
- devlink_pool_size_thtype_restore 5
- devlink_pool_size_thtype_restore 4
- devlink_pool_size_thtype_restore 2
- devlink_pool_size_thtype_restore 1
- devlink_pool_size_thtype_restore 0
-
- # bridges
- # -------
-
- ip link set dev br2 down
- ip link set dev $swp5.111 nomaster
- ip link set dev $swp4.111 nomaster
- ip link set dev $swp2.111 nomaster
- ip link del dev br2
-
- ip link set dev br1 down
- ip link set dev $swp3.111 nomaster
- ip link set dev $swp1.111 nomaster
- ip link del dev br1
-
- # $swp5
- # -----
-
- dcb buffer set dev $swp5 prio-buffer all:0
- tc qdisc del dev $swp5 root
-
- devlink_tc_bind_pool_th_restore $swp5 1 ingress
- devlink_port_pool_th_restore $swp5 2
-
- vlan_destroy $swp5 111
- mtu_restore $swp5
- ip link set dev $swp5 down
-
- # $swp4
- # -----
-
- dcb buffer set dev $swp4 prio-buffer all:0
- tc qdisc del dev $swp4 root
-
- devlink_tc_bind_pool_th_restore $swp4 1 ingress
- devlink_port_pool_th_restore $swp4 2
-
- vlan_destroy $swp4 111
- ethtool -s $swp4 autoneg on
- mtu_restore $swp4
- ip link set dev $swp4 down
-
- # $swp3
- # -----
-
- tc qdisc del dev $swp3 root
-
- devlink_tc_bind_pool_th_restore $swp3 1 egress
- devlink_port_pool_th_restore $swp3 5
-
- vlan_destroy $swp3 111
- ethtool -s $swp3 autoneg on
- mtu_restore $swp3
- ip link set dev $swp3 down
-
- # $swp2
- # -----
-
- tc qdisc del dev $swp2 root
-
- devlink_tc_bind_pool_th_restore $swp2 1 egress
- devlink_port_pool_th_restore $swp2 6
-
- vlan_destroy $swp2 111
- ethtool -s $swp2 autoneg on
- mtu_restore $swp2
- ip link set dev $swp2 down
-
- # $swp1
- # -----
-
- dcb buffer set dev $swp1 prio-buffer all:0
- tc qdisc del dev $swp1 root
-
- devlink_tc_bind_pool_th_restore $swp1 1 ingress
- devlink_port_pool_th_restore $swp1 1
-
- vlan_destroy $swp1 111
- mtu_restore $swp1
- ip link set dev $swp1 down
-}
-
-setup_prepare()
-{
- h1=${NETIFS[p1]}
- swp1=${NETIFS[p2]}
-
- swp2=${NETIFS[p3]}
- h2=${NETIFS[p4]}
-
- swp3=${NETIFS[p5]}
- swp4=${NETIFS[p6]}
-
- swp5=${NETIFS[p7]}
- h3=${NETIFS[p8]}
-
- h2mac=$(mac_get $h2)
-
- vrf_prepare
-
- h1_create
- h2_create
- h3_create
- switch_create
-}
-
-cleanup()
-{
- pre_cleanup
-
- switch_destroy
- h3_destroy
- h2_destroy
- h1_destroy
-
- vrf_cleanup
-}
-
-ping_ipv4()
-{
- ping_test $h1 192.0.2.34 " h1->h2"
- ping_test $h3 192.0.2.34 " h3->h2"
-}
-
-__test_qos_burst()
-{
- local pktsize=$1; shift
-
- RET=0
-
- start_traffic_pktsize $pktsize $h1.111 192.0.2.33 192.0.2.34 $h2mac
- sleep 1
-
- local q0=$(ethtool_stats_get $swp2 tc_transmit_queue_tc_1)
- ((q0 == 0))
- check_err $? "Transmit queue non-zero?"
-
- local d0=$(ethtool_stats_get $swp2 tc_no_buffer_discard_uc_tc_1)
-
- local cell_size=$(devlink_cell_size_get)
- local cells=$((BURST_SIZE / cell_size))
- # Each packet is $pktsize of payload + headers.
- local pkt_cells=$(((pktsize + 50 + cell_size - 1) / cell_size))
- # How many packets can we admit:
- local pkts=$((cells / pkt_cells))
-
- $MZ $h3 -p $pktsize -Q 1:111 -A 192.0.2.35 -B 192.0.2.34 \
- -a own -b $h2mac -c $pkts -t udp -q
- sleep 1
-
- local d1=$(ethtool_stats_get $swp2 tc_no_buffer_discard_uc_tc_1)
- ((d1 == d0))
- check_err $? "Drops seen on egress port: $d0 -> $d1 ($((d1 - d0)))"
-
- # Check that the queue is somewhat close to the burst size This
- # makes sure that the lack of drops above was not due to port
- # undersubscribtion.
- local q0=$(ethtool_stats_get $swp2 tc_transmit_queue_tc_1)
- local qe=$((90 * BURST_SIZE / 100))
- ((q0 > qe))
- check_err $? "Queue size expected >$qe, got $q0"
-
- stop_traffic
- sleep 2
-
- log_test "Burst: absorb $pkts ${pktsize}-B packets"
-}
-
-test_8K()
-{
- __test_qos_burst 8000
-}
-
-test_800()
-{
- __test_qos_burst 800
-}
-
-bail_on_lldpad
-
-trap cleanup EXIT
-setup_prepare
-setup_wait
-tests_run
-
-exit $EXIT_STATUS
projects / linux-2.6-microblaze.git / commitdiff