--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for the Storm Semiconductor SL93512R_BRD
+ * Gemini reference design, also initially called
+ * "Gemini324 EV-Board" before Storm acquired Storlink Semiconductor.
+ * The series were later acquired by Cortina Systems.
+ */
+
+/dts-v1/;
+
+#include "gemini.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Storlink Semiconductor Gemini324 EV-Board / Storm Semiconductor SL93512R_BRD";
+ compatible = "storlink,gemini324", "storm,sl93512r", "cortina,gemini";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory@0 {
+ /* 64 MB Samsung K4H511638B */
+ device_type = "memory";
+ reg = <0x00000000 0x4000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,19200n8 root=/dev/sda1 rw rootwait";
+ stdout-path = &uart0;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ button-wps {
+ debounce-interval = <50>;
+ wakeup-source;
+ linux,code = <KEY_WPS_BUTTON>;
+ label = "WPS";
+ /* Conflict with NAND flash */
+ gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+ };
+
+ button-setup {
+ debounce-interval = <50>;
+ wakeup-source;
+ linux,code = <KEY_SETUP>;
+ label = "factory reset";
+ /* Conflict with NAND flash */
+ gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-green-harddisk {
+ label = "sq201:green:harddisk";
+ /* Conflict with LCD (no problem) */
+ gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ linux,default-trigger = "disk-activity";
+ };
+ led-green-wireless {
+ label = "sq201:green:wireless";
+ /* Conflict with NAND flash CE0 (no problem) */
+ gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ /* Uses MDC and MDIO */
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* This is a Marvell 88E1111 ethernet transciever */
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+ };
+
+ spi {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ /* Check pin collisions */
+ gpio-sck = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ gpio-miso = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ gpio-mosi = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <1>;
+
+ switch@0 {
+ compatible = "vitesse,vsc7385";
+ reg = <0>;
+ /* Specified for 2.5 MHz or below */
+ spi-max-frequency = <2500000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+ vsc: port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac1>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+ };
+ };
+
+
+ soc {
+ flash@30000000 {
+ status = "okay";
+ /* 16MB of flash */
+ reg = <0x30000000 0x01000000>;
+
+ partition@0 {
+ label = "BOOT";
+ reg = <0x00000000 0x00020000>;
+ read-only;
+ };
+ partition@120000 {
+ label = "Kern";
+ reg = <0x00020000 0x00300000>;
+ };
+ partition@320000 {
+ label = "Ramdisk";
+ reg = <0x00320000 0x00600000>;
+ };
+ partition@920000 {
+ label = "Application";
+ reg = <0x00920000 0x00600000>;
+ };
+ partition@f20000 {
+ label = "VCTL";
+ reg = <0x00f20000 0x00020000>;
+ read-only;
+ };
+ partition@f40000 {
+ label = "CurConf";
+ reg = <0x00f40000 0x000a0000>;
+ read-only;
+ };
+ partition@fe0000 {
+ label = "FIS directory";
+ reg = <0x00fe0000 0x00020000>;
+ read-only;
+ };
+ };
+
+ syscon: syscon@40000000 {
+ pinctrl {
+ /*
+ * gpio0egrp cover line 16 used by HD LED
+ * gpio0fgrp cover line 17, 18 used by wireless LED and reset button
+ * gpio0hgrp cover line 21, 22 used by MDIO for Marvell PHY
+ * gpio0kgrp cover line 31 used by USB LED
+ */
+ gpio0_default_pins: pinctrl-gpio0 {
+ mux {
+ function = "gpio0";
+ groups = "gpio0egrp",
+ "gpio0fgrp",
+ "gpio0hgrp";
+ };
+ };
+ /*
+ * gpio1dgrp cover lines used by SPI for
+ * the Vitesse chip (28-31)
+ */
+ gpio1_default_pins: pinctrl-gpio1 {
+ mux {
+ function = "gpio1";
+ groups = "gpio1dgrp";
+ };
+ };
+ pinctrl-gmii {
+ mux {
+ function = "gmii";
+ groups = "gmii_gmac0_grp", "gmii_gmac1_grp";
+ };
+ /* Control pad skew comes from sl_switch.c in the vendor code */
+ conf0 {
+ pins = "P10 GMAC1 TXC";
+ skew-delay = <5>;
+ };
+ conf1 {
+ pins = "V11 GMAC1 TXEN";
+ skew-delay = <7>;
+ };
+ conf2 {
+ pins = "T11 GMAC1 RXC";
+ skew-delay = <8>;
+ };
+ conf3 {
+ pins = "U11 GMAC1 RXDV";
+ skew-delay = <7>;
+ };
+ conf4 {
+ pins = "V7 GMAC0 TXC";
+ skew-delay = <10>;
+ };
+ conf5 {
+ pins = "P8 GMAC0 TXEN";
+ skew-delay = <7>; /* 5 at another place? */
+ };
+ conf6 {
+ pins = "T8 GMAC0 RXC";
+ skew-delay = <15>;
+ };
+ conf7 {
+ pins = "R8 GMAC0 RXDV";
+ skew-delay = <0>;
+ };
+ conf8 {
+ /* The data lines all have default skew */
+ pins = "U8 GMAC0 RXD0", "V8 GMAC0 RXD1",
+ "P9 GMAC0 RXD2", "R9 GMAC0 RXD3",
+ "R11 GMAC1 RXD0", "P11 GMAC1 RXD1",
+ "V12 GMAC1 RXD2", "U12 GMAC1 RXD3",
+ "R10 GMAC1 TXD0", "T10 GMAC1 TXD1",
+ "U10 GMAC1 TXD2", "V10 GMAC1 TXD3";
+ skew-delay = <7>;
+ };
+ /* Appears in sl351x_gmac.c in the vendor code */
+ conf9 {
+ pins = "U7 GMAC0 TXD0", "T7 GMAC0 TXD1",
+ "R7 GMAC0 TXD2", "P7 GMAC0 TXD3";
+ skew-delay = <5>;
+ };
+ };
+ };
+ };
+
+ /* Both interfaces brought out on SATA connectors */
+ sata: sata@46000000 {
+ cortina,gemini-ata-muxmode = <0>;
+ cortina,gemini-enable-sata-bridge;
+ status = "okay";
+ };
+
+ gpio0: gpio@4d000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio0_default_pins>;
+ };
+
+ gpio1: gpio@4e000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio1_default_pins>;
+ };
+
+ pci@50000000 {
+ status = "okay";
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map =
+ <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
+ <0x4800 0 0 2 &pci_intc 1>,
+ <0x4800 0 0 3 &pci_intc 2>,
+ <0x4800 0 0 4 &pci_intc 3>,
+ <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
+ <0x5000 0 0 2 &pci_intc 2>,
+ <0x5000 0 0 3 &pci_intc 3>,
+ <0x5000 0 0 4 &pci_intc 0>,
+ <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
+ <0x5800 0 0 2 &pci_intc 3>,
+ <0x5800 0 0 3 &pci_intc 0>,
+ <0x5800 0 0 4 &pci_intc 1>,
+ <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
+ <0x6000 0 0 2 &pci_intc 0>,
+ <0x6000 0 0 3 &pci_intc 1>,
+ <0x6000 0 0 4 &pci_intc 2>;
+ };
+
+ ethernet@60000000 {
+ status = "okay";
+
+ ethernet-port@0 {
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+ };
+ ethernet-port@1 {
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+
+ ata@63000000 {
+ status = "okay";
+ };
+
+ ata@63400000 {
+ status = "okay";
+ };
+ };
+};
projects / linux-2.6-microblaze.git / commitdiff