dt-bindings: net: dsa: ocelot: document the vsc9959 core

This patch adds the required documentation for the embedded L2 switch
inside the NXP LS1028A chip.

I've submitted it in the legacy format instead of yaml schema, because
DSA itself has not yet been converted to yaml, and this driver defines
no custom bindings.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/Documentation/devicetree/bindings/net/dsa/ocelot.txt b/Documentation/devicetree/bindings/net/dsa/ocelot.txt
new file mode 100644 (file)
index 0000000..66a129f
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/ocelot.txt
@@ -0,0 +1,116 @@
+Microchip Ocelot switch driver family
+=====================================
+
+Felix
+-----
+
+The VSC9959 core is currently the only switch supported by the driver, and is
+found in the NXP LS1028A. It is a PCI device, part of the larger ENETC root
+complex. As a result, the ethernet-switch node is a sub-node of the PCIe root
+complex node and its "reg" property conforms to the parent node bindings:
+
+* reg: Specifies PCIe Device Number and Function Number of the endpoint device,
+  in this case for the Ethernet L2Switch it is PF5 (of device 0, bus 0).
+
+It does not require a "compatible" string.
+
+The interrupt line is used to signal availability of PTP TX timestamps and for
+TSN frame preemption.
+
+For the external switch ports, depending on board configuration, "phy-mode" and
+"phy-handle" are populated by board specific device tree instances. Ports 4 and
+5 are fixed as internal ports in the NXP LS1028A instantiation.
+
+The CPU port property ("ethernet") configures the feature called "NPI port" in
+the Ocelot hardware core. The CPU port in Ocelot is a set of queues, which are
+connected, in the Node Processor Interface (NPI) mode, to an Ethernet port.
+By default, in fsl-ls1028a.dtsi, the NPI port is assigned to the internal
+2.5Gbps port@4, but can be moved to the 1Gbps port@5, depending on the specific
+use case.  Moving the NPI port to an external switch port is hardware possible,
+but there is no platform support for the Linux system on the LS1028A chip to
+operate as an entire slave DSA chip.  NPI functionality (and therefore DSA
+tagging) is supported on a single port at a time.
+
+Any port can be disabled (and in fsl-ls1028a.dtsi, they are indeed all disabled
+by default, and should be enabled on a per-board basis). But if any external
+switch port is enabled at all, the ENETC PF2 (enetc_port2) should be enabled as
+well, regardless of whether it is configured as the DSA master or not. This is
+because the Felix PHYLINK implementation accesses the MAC PCS registers, which
+in hardware truly belong to the ENETC port #2 and not to Felix.
+
+Supported PHY interface types (appropriate SerDes protocol setting changes are
+needed in the RCW binary):
+
+* phy_mode = "internal": on ports 4 and 5
+* phy_mode = "sgmii": on ports 0, 1, 2, 3
+* phy_mode = "qsgmii": on ports 0, 1, 2, 3
+* phy_mode = "usxgmii": on ports 0, 1, 2, 3
+* phy_mode = "2500base-x": on ports 0, 1, 2, 3
+
+For the rest of the device tree binding definitions, which are standard DSA and
+PCI, refer to the following documents:
+
+Documentation/devicetree/bindings/net/dsa/dsa.txt
+Documentation/devicetree/bindings/pci/pci.txt
+
+Example:
+
+&soc {
+       pcie@1f0000000 { /* Integrated Endpoint Root Complex */
+               ethernet-switch@0,5 {
+                       reg = <0x000500 0 0 0 0>;
+                       /* IEP INT_B */
+                       interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+
+                       ports {
+                               #address-cells = <1>;
+                               #size-cells = <0>;
+
+                               /* External ports */
+                               port@0 {
+                                       reg = <0>;
+                                       label = "swp0";
+                               };
+
+                               port@1 {
+                                       reg = <1>;
+                                       label = "swp1";
+                               };
+
+                               port@2 {
+                                       reg = <2>;
+                                       label = "swp2";
+                               };
+
+                               port@3 {
+                                       reg = <3>;
+                                       label = "swp3";
+                               };
+
+                               /* Tagging CPU port */
+                               port@4 {
+                                       reg = <4>;
+                                       ethernet = <&enetc_port2>;
+                                       phy-mode = "internal";
+
+                                       fixed-link {
+                                               speed = <2500>;
+                                               full-duplex;
+                                       };
+                               };
+
+                               /* Non-tagging CPU port */
+                               port@5 {
+                                       reg = <5>;
+                                       phy-mode = "internal";
+                                       status = "disabled";
+
+                                       fixed-link {
+                                               speed = <1000>;
+                                               full-duplex;
+                                       };
+                               };
+                       };
+               };
+       };
+};