has to request that the PCI layer set up the MSI capability for this
device.
-4.2.1 pci_enable_msi_range
+4.2.1 pci_enable_msi
+
+int pci_enable_msi(struct pci_dev *dev)
+
+A successful call allocates ONE interrupt to the device, regardless
+of how many MSIs the device supports. The device is switched from
+pin-based interrupt mode to MSI mode. The dev->irq number is changed
+to a new number which represents the message signaled interrupt;
+consequently, this function should be called before the driver calls
+request_irq(), because an MSI is delivered via a vector that is
+different from the vector of a pin-based interrupt.
+
+4.2.2 pci_enable_msi_range
int pci_enable_msi_range(struct pci_dev *dev, int minvec, int maxvec)
return pci_enable_msi_range(pdev, nvec, nvec);
}
+Note, unlike pci_enable_msi_exact() function, which could be also used to
+enable a particular number of MSI-X interrupts, pci_enable_msi_range()
+returns either a negative errno or 'nvec' (not negative errno or 0 - as
+pci_enable_msi_exact() does).
+
4.2.1.3 Single MSI mode
The most notorious example of the request type described above is
return pci_enable_msi_range(pdev, 1, 1);
}
-4.2.2 pci_disable_msi
+Note, unlike pci_enable_msi() function, which could be also used to
+enable the single MSI mode, pci_enable_msi_range() returns either a
+negative errno or 1 (not negative errno or 0 - as pci_enable_msi()
+does).
+
+4.2.3 pci_enable_msi_exact
+
+int pci_enable_msi_exact(struct pci_dev *dev, int nvec)
+
+This variation on pci_enable_msi_range() call allows a device driver to
+request exactly 'nvec' MSIs.
+
+If this function returns a negative number, it indicates an error and
+the driver should not attempt to request any more MSI interrupts for
+this device.
+
+By contrast with pci_enable_msi_range() function, pci_enable_msi_exact()
+returns zero in case of success, which indicates MSI interrupts have been
+successfully allocated.
+
+4.2.4 pci_disable_msi
void pci_disable_msi(struct pci_dev *dev)
Failure to do so results in a BUG_ON(), leaving the device with
MSI enabled and thus leaking its vector.
-4.2.3 pci_msi_vec_count
+4.2.4 pci_msi_vec_count
int pci_msi_vec_count(struct pci_dev *dev)
static int foo_driver_enable_msix(struct foo_adapter *adapter, int nvec)
{
- return pci_enable_msi_range(adapter->pdev, adapter->msix_entries,
- 1, nvec);
+ return pci_enable_msix_range(adapter->pdev, adapter->msix_entries,
+ 1, nvec);
}
Note the value of 'minvec' parameter is 1. As 'minvec' is inclusive,
static int foo_driver_enable_msix(struct foo_adapter *adapter, int nvec)
{
- return pci_enable_msi_range(adapter->pdev, adapter->msix_entries,
- FOO_DRIVER_MINIMUM_NVEC, nvec);
+ return pci_enable_msix_range(adapter->pdev, adapter->msix_entries,
+ FOO_DRIVER_MINIMUM_NVEC, nvec);
}
4.3.1.2 Exact number of MSI-X interrupts
static int foo_driver_enable_msix(struct foo_adapter *adapter, int nvec)
{
- return pci_enable_msi_range(adapter->pdev, adapter->msix_entries,
- nvec, nvec);
+ return pci_enable_msix_range(adapter->pdev, adapter->msix_entries,
+ nvec, nvec);
}
+Note, unlike pci_enable_msix_exact() function, which could be also used to
+enable a particular number of MSI-X interrupts, pci_enable_msix_range()
+returns either a negative errno or 'nvec' (not negative errno or 0 - as
+pci_enable_msix_exact() does).
+
4.3.1.3 Specific requirements to the number of MSI-X interrupts
As noted above, there could be devices that can not operate with just any
any error code other than -ENOSPC indicates a fatal error and should not
be retried.
-4.3.2 pci_disable_msix
+4.3.2 pci_enable_msix_exact
+
+int pci_enable_msix_exact(struct pci_dev *dev,
+ struct msix_entry *entries, int nvec)
+
+This variation on pci_enable_msix_range() call allows a device driver to
+request exactly 'nvec' MSI-Xs.
+
+If this function returns a negative number, it indicates an error and
+the driver should not attempt to allocate any more MSI-X interrupts for
+this device.
+
+By contrast with pci_enable_msix_range() function, pci_enable_msix_exact()
+returns zero in case of success, which indicates MSI-X interrupts have been
+successfully allocated.
+
+Another version of a routine that enables MSI-X mode for a device with
+specific requirements described in chapter 4.3.1.3 might look like this:
+
+/*
+ * Assume 'minvec' and 'maxvec' are non-zero
+ */
+static int foo_driver_enable_msix(struct foo_adapter *adapter,
+ int minvec, int maxvec)
+{
+ int rc;
+
+ minvec = roundup_pow_of_two(minvec);
+ maxvec = rounddown_pow_of_two(maxvec);
+
+ if (minvec > maxvec)
+ return -ERANGE;
+
+retry:
+ rc = pci_enable_msix_exact(adapter->pdev,
+ adapter->msix_entries, maxvec);
+
+ /*
+ * -ENOSPC is the only error code allowed to be analyzed
+ */
+ if (rc == -ENOSPC) {
+ if (maxvec == 1)
+ return -ENOSPC;
+
+ maxvec /= 2;
+
+ if (minvec > maxvec)
+ return -ENOSPC;
+
+ goto retry;
+ } else if (rc < 0) {
+ return rc;
+ }
+
+ return maxvec;
+}
+
+4.3.3 pci_disable_msix
void pci_disable_msix(struct pci_dev *dev)
CPUSETS
M: Li Zefan <lizefan@huawei.com>
+L: cgroups@vger.kernel.org
W: http://www.bullopensource.org/cpuset/
W: http://oss.sgi.com/projects/cpusets/
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup.git
S: Maintained
F: Documentation/cgroups/cpusets.txt
F: include/linux/cpuset.h
#include <linux/cpu_pm.h>
#include <linux/suspend.h>
#include <linux/err.h>
+#include <linux/slab.h>
#include <linux/clk/tegra.h>
#include <asm/smp_plat.h>
*handle = DMA_ERROR_CODE;
size = PAGE_ALIGN(size);
- if (gfp & GFP_ATOMIC)
+ if (!(gfp & __GFP_WAIT))
return __iommu_alloc_atomic(dev, size, handle);
/*
flag |= __GFP_ZERO;
again:
page = NULL;
- if (!(flag & GFP_ATOMIC))
+ /* CMA can be used only in the context which permits sleeping */
+ if (flag & __GFP_WAIT)
page = dma_alloc_from_contiguous(dev, count, get_order(size));
+ /* fallback */
if (!page)
page = alloc_pages_node(dev_to_node(dev), flag, get_order(size));
if (!page)
kobject_uevent(&ac->charger.dev->kobj, KOBJ_CHANGE);
return 0;
}
+#else
+#define acpi_ac_resume NULL
#endif
static SIMPLE_DEV_PM_OPS(acpi_ac_pm_ops, NULL, acpi_ac_resume);
acpi_battery_update(battery);
return 0;
}
+#else
+#define acpi_battery_resume NULL
#endif
static SIMPLE_DEV_PM_OPS(acpi_battery_pm, NULL, acpi_battery_resume);
},
{
.callback = dmi_disable_osi_win8,
- .ident = "Dell Inspiron 15R SE",
- .matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
- DMI_MATCH(DMI_PRODUCT_NAME, "Inspiron 7520"),
- },
- },
- {
- .callback = dmi_disable_osi_win8,
.ident = "ThinkPad Edge E530",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
DMI_MATCH(DMI_PRODUCT_VERSION, "2349D15"),
},
},
- {
- .callback = dmi_disable_osi_win8,
- .ident = "HP ProBook 2013 models",
- .matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
- DMI_MATCH(DMI_PRODUCT_NAME, "HP ProBook "),
- DMI_MATCH(DMI_PRODUCT_NAME, " G1"),
- },
- },
- {
- .callback = dmi_disable_osi_win8,
- .ident = "HP EliteBook 2013 models",
- .matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
- DMI_MATCH(DMI_PRODUCT_NAME, "HP EliteBook "),
- DMI_MATCH(DMI_PRODUCT_NAME, " G1"),
- },
- },
- {
- .callback = dmi_disable_osi_win8,
- .ident = "HP ZBook 14",
- .matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
- DMI_MATCH(DMI_PRODUCT_NAME, "HP ZBook 14"),
- },
- },
- {
- .callback = dmi_disable_osi_win8,
- .ident = "HP ZBook 15",
- .matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
- DMI_MATCH(DMI_PRODUCT_NAME, "HP ZBook 15"),
- },
- },
- {
- .callback = dmi_disable_osi_win8,
- .ident = "HP ZBook 17",
- .matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
- DMI_MATCH(DMI_PRODUCT_NAME, "HP ZBook 17"),
- },
- },
- {
- .callback = dmi_disable_osi_win8,
- .ident = "HP EliteBook 8780w",
- .matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
- DMI_MATCH(DMI_PRODUCT_NAME, "HP EliteBook 8780w"),
- },
- },
/*
* BIOS invocation of _OSI(Linux) is almost always a BIOS bug.
#ifdef CONFIG_PM_SLEEP
static int acpi_button_resume(struct device *dev);
+#else
+#define acpi_button_resume NULL
#endif
static SIMPLE_DEV_PM_OPS(acpi_button_pm, NULL, acpi_button_resume);
static ssize_t show_docked(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct acpi_device *tmp;
-
struct dock_station *dock_station = dev->platform_data;
+ struct acpi_device *adev = NULL;
- if (!acpi_bus_get_device(dock_station->handle, &tmp))
- return snprintf(buf, PAGE_SIZE, "1\n");
- return snprintf(buf, PAGE_SIZE, "0\n");
+ acpi_bus_get_device(dock_station->handle, &adev);
+ return snprintf(buf, PAGE_SIZE, "%u\n", acpi_device_enumerated(adev));
}
static DEVICE_ATTR(docked, S_IRUGO, show_docked, NULL);
#ifdef CONFIG_PM_SLEEP
static int acpi_fan_suspend(struct device *dev);
static int acpi_fan_resume(struct device *dev);
+#else
+#define acpi_fan_suspend NULL
+#define acpi_fan_resume NULL
#endif
static SIMPLE_DEV_PM_OPS(acpi_fan_pm, acpi_fan_suspend, acpi_fan_resume);
pin_name(pin));
}
+ kfree(entry);
return 0;
}
{
unsigned long x;
struct acpi_battery *battery = to_acpi_battery(dev_get_drvdata(dev));
- if (sscanf(buf, "%ld\n", &x) == 1)
+ if (sscanf(buf, "%lu\n", &x) == 1)
battery->alarm_capacity = x /
(1000 * acpi_battery_scale(battery));
if (battery->present)
acpi_sbs_callback(sbs);
return 0;
}
+#else
+#define acpi_sbs_resume NULL
#endif
static SIMPLE_DEV_PM_OPS(acpi_sbs_pm, NULL, acpi_sbs_resume);
#ifdef CONFIG_PM_SLEEP
static int acpi_thermal_resume(struct device *dev);
+#else
+#define acpi_thermal_resume NULL
#endif
static SIMPLE_DEV_PM_OPS(acpi_thermal_pm, NULL, acpi_thermal_resume);
module_param(allow_duplicates, bool, 0644);
/*
- * For Windows 8 systems: if set ture and the GPU driver has
- * registered a backlight interface, skip registering ACPI video's.
+ * For Windows 8 systems: used to decide if video module
+ * should skip registering backlight interface of its own.
*/
-static bool use_native_backlight = false;
-module_param(use_native_backlight, bool, 0644);
+static int use_native_backlight_param = -1;
+module_param_named(use_native_backlight, use_native_backlight_param, int, 0444);
+static bool use_native_backlight_dmi = false;
static int register_count;
static struct mutex video_list_lock;
static int acpi_video_switch_brightness(struct acpi_video_device *device,
int event);
+static bool acpi_video_use_native_backlight(void)
+{
+ if (use_native_backlight_param != -1)
+ return use_native_backlight_param;
+ else
+ return use_native_backlight_dmi;
+}
+
static bool acpi_video_verify_backlight_support(void)
{
- if (acpi_osi_is_win8() && use_native_backlight &&
+ if (acpi_osi_is_win8() && acpi_video_use_native_backlight() &&
backlight_device_registered(BACKLIGHT_RAW))
return false;
return acpi_video_backlight_support();
return 0;
}
+static int __init video_set_use_native_backlight(const struct dmi_system_id *d)
+{
+ use_native_backlight_dmi = true;
+ return 0;
+}
+
static struct dmi_system_id video_dmi_table[] __initdata = {
/*
* Broken _BQC workaround http://bugzilla.kernel.org/show_bug.cgi?id=13121
DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 7720"),
},
},
+ {
+ .callback = video_set_use_native_backlight,
+ .ident = "ThinkPad T430s",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+ DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad T430s"),
+ },
+ },
+ {
+ .callback = video_set_use_native_backlight,
+ .ident = "ThinkPad X230",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+ DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad X230"),
+ },
+ },
+ {
+ .callback = video_set_use_native_backlight,
+ .ident = "ThinkPad X1 Carbon",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+ DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad X1 Carbon"),
+ },
+ },
+ {
+ .callback = video_set_use_native_backlight,
+ .ident = "Lenovo Yoga 13",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+ DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo IdeaPad Yoga 13"),
+ },
+ },
+ {
+ .callback = video_set_use_native_backlight,
+ .ident = "Dell Inspiron 7520",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+ DMI_MATCH(DMI_PRODUCT_VERSION, "Inspiron 7520"),
+ },
+ },
+ {
+ .callback = video_set_use_native_backlight,
+ .ident = "Acer Aspire 5733Z",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 5733Z"),
+ },
+ },
+ {
+ .callback = video_set_use_native_backlight,
+ .ident = "Acer Aspire V5-431",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "Aspire V5-431"),
+ },
+ },
+ {
+ .callback = video_set_use_native_backlight,
+ .ident = "HP ProBook 4340s",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+ DMI_MATCH(DMI_PRODUCT_VERSION, "HP ProBook 4340s"),
+ },
+ },
+ {
+ .callback = video_set_use_native_backlight,
+ .ident = "HP ProBook 2013 models",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "HP ProBook "),
+ DMI_MATCH(DMI_PRODUCT_NAME, " G1"),
+ },
+ },
+ {
+ .callback = video_set_use_native_backlight,
+ .ident = "HP EliteBook 2013 models",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "HP EliteBook "),
+ DMI_MATCH(DMI_PRODUCT_NAME, " G1"),
+ },
+ },
+ {
+ .callback = video_set_use_native_backlight,
+ .ident = "HP ZBook 14",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "HP ZBook 14"),
+ },
+ },
+ {
+ .callback = video_set_use_native_backlight,
+ .ident = "HP ZBook 15",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "HP ZBook 15"),
+ },
+ },
+ {
+ .callback = video_set_use_native_backlight,
+ .ident = "HP ZBook 17",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "HP ZBook 17"),
+ },
+ },
+ {
+ .callback = video_set_use_native_backlight,
+ .ident = "HP EliteBook 8780w",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "HP EliteBook 8780w"),
+ },
+ },
{}
};
union acpi_object *o;
struct acpi_video_device_brightness *br = NULL;
int result = -EINVAL;
+ u32 value;
if (!ACPI_SUCCESS(acpi_video_device_lcd_query_levels(device, &obj))) {
ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Could not query available "
printk(KERN_ERR PREFIX "Invalid data\n");
continue;
}
- br->levels[count] = (u32) o->integer.value;
+ value = (u32) o->integer.value;
+ /* Skip duplicate entries */
+ if (count > 2 && br->levels[count - 1] == value)
+ continue;
+
+ br->levels[count] = value;
if (br->levels[count] > max_level)
max_level = br->levels[count];
DMI_MATCH(DMI_PRODUCT_NAME, "UL30A"),
},
},
- {
- .callback = video_detect_force_vendor,
- .ident = "HP EliteBook Revolve 810",
- .matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
- DMI_MATCH(DMI_PRODUCT_NAME, "HP EliteBook Revolve 810 G1"),
- },
- },
- {
- .callback = video_detect_force_vendor,
- .ident = "Lenovo Yoga 13",
- .matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
- DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo IdeaPad Yoga 13"),
- },
- },
{ },
};
config SATA_MV
tristate "Marvell SATA support"
+ select GENERIC_PHY
help
This option enables support for the Marvell Serial ATA family.
Currently supports 88SX[56]0[48][01] PCI(-X) chips,
/* board IDs by feature in alphabetical order */
board_ahci,
board_ahci_ign_iferr,
+ board_ahci_noncq,
board_ahci_nosntf,
board_ahci_yes_fbs,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
+ [board_ahci_noncq] = {
+ AHCI_HFLAGS (AHCI_HFLAG_NO_NCQ),
+ .flags = AHCI_FLAG_COMMON,
+ .pio_mask = ATA_PIO4,
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &ahci_ops,
+ },
[board_ahci_nosntf] = {
AHCI_HFLAGS (AHCI_HFLAG_NO_SNTF),
.flags = AHCI_FLAG_COMMON,
{ PCI_VDEVICE(ASMEDIA, 0x0611), board_ahci }, /* ASM1061 */
{ PCI_VDEVICE(ASMEDIA, 0x0612), board_ahci }, /* ASM1062 */
+ /*
+ * Samsung SSDs found on some macbooks. NCQ times out.
+ * https://bugzilla.kernel.org/show_bug.cgi?id=60731
+ */
+ { PCI_VDEVICE(SAMSUNG, 0x1600), board_ahci_noncq },
+
/* Enmotus */
{ PCI_DEVICE(0x1c44, 0x8000), board_ahci },
nvec = rc;
rc = pci_enable_msi_block(pdev, nvec);
- if (rc)
+ if (rc < 0)
goto intx;
+ else if (rc > 0)
+ goto single_msi;
return nvec;
* otherwise. Don't try hard to recover it.
*/
ap->pmp_link[ap->nr_pmp_links - 1].flags |= ATA_LFLAG_NO_RETRY;
- } else if (vendor == 0x197b && devid == 0x2352) {
- /* chip found in Thermaltake BlackX Duet, jmicron JMB350? */
+ } else if (vendor == 0x197b && (devid == 0x2352 || devid == 0x0325)) {
+ /*
+ * 0x2352: found in Thermaltake BlackX Duet, jmicron JMB350?
+ * 0x0325: jmicron JMB394.
+ */
ata_for_each_link(link, ap, EDGE) {
/* SRST breaks detection and disks get misclassified
* LPM disabled to avoid potential problems
return PTR_ERR(priv->clk);
}
- clk_prepare_enable(priv->clk);
+ ret = clk_prepare_enable(priv->clk);
+ if (ret)
+ return ret;
host = ata_host_alloc(&pdev->dev, 1);
if (!host) {
struct ata_host *host = dev_get_drvdata(dev);
struct pata_imx_priv *priv = host->private_data;
- clk_prepare_enable(priv->clk);
+ int ret = clk_prepare_enable(priv->clk);
+ if (ret)
+ return ret;
__raw_writel(priv->ata_ctl, priv->host_regs + PATA_IMX_ATA_CONTROL);
if (!hpriv->port_phys)
return -ENOMEM;
host->private_data = hpriv;
- hpriv->n_ports = n_ports;
hpriv->board_idx = chip_soc;
host->iomap = NULL;
rc = PTR_ERR(hpriv->port_phys[port]);
hpriv->port_phys[port] = NULL;
if (rc != -EPROBE_DEFER)
- dev_warn(&pdev->dev, "error getting phy %d",
- rc);
+ dev_warn(&pdev->dev, "error getting phy %d", rc);
+
+ /* Cleanup only the initialized ports */
+ hpriv->n_ports = port;
goto err;
} else
phy_power_on(hpriv->port_phys[port]);
}
+ /* All the ports have been initialized */
+ hpriv->n_ports = n_ports;
+
/*
* (Re-)program MBUS remapping windows if we are asked to.
*/
clk_disable_unprepare(hpriv->clk);
clk_put(hpriv->clk);
}
- for (port = 0; port < n_ports; port++) {
+ for (port = 0; port < hpriv->n_ports; port++) {
if (!IS_ERR(hpriv->port_clks[port])) {
clk_disable_unprepare(hpriv->port_clks[port]);
clk_put(hpriv->port_clks[port]);
{ "ST380011ASL", SIL_QUIRK_MOD15WRITE },
{ "ST3120022ASL", SIL_QUIRK_MOD15WRITE },
{ "ST3160021ASL", SIL_QUIRK_MOD15WRITE },
+ { "TOSHIBA MK2561GSYN", SIL_QUIRK_MOD15WRITE },
{ "Maxtor 4D060H3", SIL_QUIRK_UDMA5MAX },
{ }
};
up_read(&policy->rwsem);
if (cpu != policy->cpu) {
- if (!frozen)
- sysfs_remove_link(&dev->kobj, "cpufreq");
+ sysfs_remove_link(&dev->kobj, "cpufreq");
} else if (cpus > 1) {
new_cpu = cpufreq_nominate_new_policy_cpu(policy, cpu);
if (new_cpu >= 0) {
#define SAMPLE_COUNT 3
-#define BYT_RATIOS 0x66a
-#define BYT_VIDS 0x66b
+#define BYT_RATIOS 0x66a
+#define BYT_VIDS 0x66b
+#define BYT_TURBO_RATIOS 0x66c
+
#define FRAC_BITS 8
#define int_tofp(X) ((int64_t)(X) << FRAC_BITS)
{
u64 value;
rdmsrl(BYT_RATIOS, value);
- return value & 0xFF;
+ return (value >> 8) & 0xFF;
}
static int byt_get_max_pstate(void)
return (value >> 16) & 0xFF;
}
+static int byt_get_turbo_pstate(void)
+{
+ u64 value;
+ rdmsrl(BYT_TURBO_RATIOS, value);
+ return value & 0x3F;
+}
+
static void byt_set_pstate(struct cpudata *cpudata, int pstate)
{
u64 val;
.funcs = {
.get_max = byt_get_max_pstate,
.get_min = byt_get_min_pstate,
- .get_turbo = byt_get_max_pstate,
+ .get_turbo = byt_get_turbo_pstate,
.set = byt_set_pstate,
.get_vid = byt_get_vid,
},
{
struct powernow_k8_data *data;
struct init_on_cpu init_on_cpu;
- int rc;
+ int rc, cpu;
smp_call_function_single(pol->cpu, check_supported_cpu, &rc, 1);
if (rc)
pr_debug("cpu_init done, current fid 0x%x, vid 0x%x\n",
data->currfid, data->currvid);
- per_cpu(powernow_data, pol->cpu) = data;
+ /* Point all the CPUs in this policy to the same data */
+ for_each_cpu(cpu, pol->cpus)
+ per_cpu(powernow_data, cpu) = data;
return 0;
static int powernowk8_cpu_exit(struct cpufreq_policy *pol)
{
struct powernow_k8_data *data = per_cpu(powernow_data, pol->cpu);
+ int cpu;
if (!data)
return -EINVAL;
kfree(data->powernow_table);
kfree(data);
- per_cpu(powernow_data, pol->cpu) = NULL;
+ for_each_cpu(cpu, pol->cpus)
+ per_cpu(powernow_data, cpu) = NULL;
return 0;
}
return 0;
}
+/*
+ * On some platforms, _DSM(nouveau_op_dsm_muid, func0) has special
+ * requirements on the fourth parameter, so a private implementation
+ * instead of using acpi_check_dsm().
+ */
+static int nouveau_check_optimus_dsm(acpi_handle handle)
+{
+ int result;
+
+ /*
+ * Function 0 returns a Buffer containing available functions.
+ * The args parameter is ignored for function 0, so just put 0 in it
+ */
+ if (nouveau_optimus_dsm(handle, 0, 0, &result))
+ return 0;
+
+ /*
+ * ACPI Spec v4 9.14.1: if bit 0 is zero, no function is supported.
+ * If the n-th bit is enabled, function n is supported
+ */
+ return result & 1 && result & (1 << NOUVEAU_DSM_OPTIMUS_CAPS);
+}
+
static int nouveau_dsm(acpi_handle handle, int func, int arg)
{
int ret = 0;
1 << NOUVEAU_DSM_POWER))
retval |= NOUVEAU_DSM_HAS_MUX;
- if (acpi_check_dsm(dhandle, nouveau_op_dsm_muid, 0x00000100,
- 1 << NOUVEAU_DSM_OPTIMUS_CAPS))
+ if (nouveau_check_optimus_dsm(dhandle))
retval |= NOUVEAU_DSM_HAS_OPT;
if (retval & NOUVEAU_DSM_HAS_OPT) {
#define ARM_SMMU_PTE_CONT_SIZE (PAGE_SIZE * ARM_SMMU_PTE_CONT_ENTRIES)
#define ARM_SMMU_PTE_CONT_MASK (~(ARM_SMMU_PTE_CONT_SIZE - 1))
-#define ARM_SMMU_PTE_HWTABLE_SIZE (PTRS_PER_PTE * sizeof(pte_t))
/* Stage-1 PTE */
#define ARM_SMMU_PTE_AP_UNPRIV (((pteval_t)1) << 6)
#define ARM_SMMU_GR1_CBAR(n) (0x0 + ((n) << 2))
#define CBAR_VMID_SHIFT 0
#define CBAR_VMID_MASK 0xff
+#define CBAR_S1_BPSHCFG_SHIFT 8
+#define CBAR_S1_BPSHCFG_MASK 3
+#define CBAR_S1_BPSHCFG_NSH 3
#define CBAR_S1_MEMATTR_SHIFT 12
#define CBAR_S1_MEMATTR_MASK 0xf
#define CBAR_S1_MEMATTR_WB 0xf
struct arm_smmu_cfg root_cfg;
phys_addr_t output_mask;
- struct mutex lock;
+ spinlock_t lock;
};
static DEFINE_SPINLOCK(arm_smmu_devices_lock);
return IRQ_HANDLED;
}
+static void arm_smmu_flush_pgtable(struct arm_smmu_device *smmu, void *addr,
+ size_t size)
+{
+ unsigned long offset = (unsigned long)addr & ~PAGE_MASK;
+
+
+ /* Ensure new page tables are visible to the hardware walker */
+ if (smmu->features & ARM_SMMU_FEAT_COHERENT_WALK) {
+ dsb();
+ } else {
+ /*
+ * If the SMMU can't walk tables in the CPU caches, treat them
+ * like non-coherent DMA since we need to flush the new entries
+ * all the way out to memory. There's no possibility of
+ * recursion here as the SMMU table walker will not be wired
+ * through another SMMU.
+ */
+ dma_map_page(smmu->dev, virt_to_page(addr), offset, size,
+ DMA_TO_DEVICE);
+ }
+}
+
static void arm_smmu_init_context_bank(struct arm_smmu_domain *smmu_domain)
{
u32 reg;
if (smmu->version == 1)
reg |= root_cfg->irptndx << CBAR_IRPTNDX_SHIFT;
- /* Use the weakest memory type, so it is overridden by the pte */
- if (stage1)
- reg |= (CBAR_S1_MEMATTR_WB << CBAR_S1_MEMATTR_SHIFT);
- else
+ /*
+ * Use the weakest shareability/memory types, so they are
+ * overridden by the ttbcr/pte.
+ */
+ if (stage1) {
+ reg |= (CBAR_S1_BPSHCFG_NSH << CBAR_S1_BPSHCFG_SHIFT) |
+ (CBAR_S1_MEMATTR_WB << CBAR_S1_MEMATTR_SHIFT);
+ } else {
reg |= ARM_SMMU_CB_VMID(root_cfg) << CBAR_VMID_SHIFT;
+ }
writel_relaxed(reg, gr1_base + ARM_SMMU_GR1_CBAR(root_cfg->cbndx));
if (smmu->version > 1) {
}
/* TTBR0 */
+ arm_smmu_flush_pgtable(smmu, root_cfg->pgd,
+ PTRS_PER_PGD * sizeof(pgd_t));
reg = __pa(root_cfg->pgd);
writel_relaxed(reg, cb_base + ARM_SMMU_CB_TTBR0_LO);
reg = (phys_addr_t)__pa(root_cfg->pgd) >> 32;
goto out_free_domain;
smmu_domain->root_cfg.pgd = pgd;
- mutex_init(&smmu_domain->lock);
+ spin_lock_init(&smmu_domain->lock);
domain->priv = smmu_domain;
return 0;
struct arm_smmu_domain *smmu_domain = domain->priv;
struct arm_smmu_device *device_smmu = dev->archdata.iommu;
struct arm_smmu_master *master;
+ unsigned long flags;
if (!device_smmu) {
dev_err(dev, "cannot attach to SMMU, is it on the same bus?\n");
* Sanity check the domain. We don't currently support domains
* that cross between different SMMU chains.
*/
- mutex_lock(&smmu_domain->lock);
+ spin_lock_irqsave(&smmu_domain->lock, flags);
if (!smmu_domain->leaf_smmu) {
/* Now that we have a master, we can finalise the domain */
ret = arm_smmu_init_domain_context(domain, dev);
dev_name(device_smmu->dev));
goto err_unlock;
}
- mutex_unlock(&smmu_domain->lock);
+ spin_unlock_irqrestore(&smmu_domain->lock, flags);
/* Looks ok, so add the device to the domain */
master = find_smmu_master(smmu_domain->leaf_smmu, dev->of_node);
return arm_smmu_domain_add_master(smmu_domain, master);
err_unlock:
- mutex_unlock(&smmu_domain->lock);
+ spin_unlock_irqrestore(&smmu_domain->lock, flags);
return ret;
}
arm_smmu_domain_remove_master(smmu_domain, master);
}
-static void arm_smmu_flush_pgtable(struct arm_smmu_device *smmu, void *addr,
- size_t size)
-{
- unsigned long offset = (unsigned long)addr & ~PAGE_MASK;
-
- /*
- * If the SMMU can't walk tables in the CPU caches, treat them
- * like non-coherent DMA since we need to flush the new entries
- * all the way out to memory. There's no possibility of recursion
- * here as the SMMU table walker will not be wired through another
- * SMMU.
- */
- if (!(smmu->features & ARM_SMMU_FEAT_COHERENT_WALK))
- dma_map_page(smmu->dev, virt_to_page(addr), offset, size,
- DMA_TO_DEVICE);
-}
-
static bool arm_smmu_pte_is_contiguous_range(unsigned long addr,
unsigned long end)
{
if (pmd_none(*pmd)) {
/* Allocate a new set of tables */
- pgtable_t table = alloc_page(PGALLOC_GFP);
+ pgtable_t table = alloc_page(GFP_ATOMIC|__GFP_ZERO);
if (!table)
return -ENOMEM;
- arm_smmu_flush_pgtable(smmu, page_address(table),
- ARM_SMMU_PTE_HWTABLE_SIZE);
+ arm_smmu_flush_pgtable(smmu, page_address(table), PAGE_SIZE);
if (!pgtable_page_ctor(table)) {
__free_page(table);
return -ENOMEM;
#ifndef __PAGETABLE_PMD_FOLDED
if (pud_none(*pud)) {
- pmd = pmd_alloc_one(NULL, addr);
+ pmd = (pmd_t *)get_zeroed_page(GFP_ATOMIC);
if (!pmd)
return -ENOMEM;
+
+ arm_smmu_flush_pgtable(smmu, pmd, PAGE_SIZE);
+ pud_populate(NULL, pud, pmd);
+ arm_smmu_flush_pgtable(smmu, pud, sizeof(*pud));
+
+ pmd += pmd_index(addr);
} else
#endif
pmd = pmd_offset(pud, addr);
next = pmd_addr_end(addr, end);
ret = arm_smmu_alloc_init_pte(smmu, pmd, addr, end, pfn,
flags, stage);
- pud_populate(NULL, pud, pmd);
- arm_smmu_flush_pgtable(smmu, pud, sizeof(*pud));
phys += next - addr;
} while (pmd++, addr = next, addr < end);
#ifndef __PAGETABLE_PUD_FOLDED
if (pgd_none(*pgd)) {
- pud = pud_alloc_one(NULL, addr);
+ pud = (pud_t *)get_zeroed_page(GFP_ATOMIC);
if (!pud)
return -ENOMEM;
+
+ arm_smmu_flush_pgtable(smmu, pud, PAGE_SIZE);
+ pgd_populate(NULL, pgd, pud);
+ arm_smmu_flush_pgtable(smmu, pgd, sizeof(*pgd));
+
+ pud += pud_index(addr);
} else
#endif
pud = pud_offset(pgd, addr);
next = pud_addr_end(addr, end);
ret = arm_smmu_alloc_init_pmd(smmu, pud, addr, next, phys,
flags, stage);
- pgd_populate(NULL, pud, pgd);
- arm_smmu_flush_pgtable(smmu, pgd, sizeof(*pgd));
phys += next - addr;
} while (pud++, addr = next, addr < end);
struct arm_smmu_cfg *root_cfg = &smmu_domain->root_cfg;
pgd_t *pgd = root_cfg->pgd;
struct arm_smmu_device *smmu = root_cfg->smmu;
+ unsigned long irqflags;
if (root_cfg->cbar == CBAR_TYPE_S2_TRANS) {
stage = 2;
if (paddr & ~output_mask)
return -ERANGE;
- mutex_lock(&smmu_domain->lock);
+ spin_lock_irqsave(&smmu_domain->lock, irqflags);
pgd += pgd_index(iova);
end = iova + size;
do {
} while (pgd++, iova != end);
out_unlock:
- mutex_unlock(&smmu_domain->lock);
-
- /* Ensure new page tables are visible to the hardware walker */
- if (smmu->features & ARM_SMMU_FEAT_COHERENT_WALK)
- dsb();
+ spin_unlock_irqrestore(&smmu_domain->lock, irqflags);
return ret;
}
if (!iommu_present(&platform_bus_type))
bus_set_iommu(&platform_bus_type, &arm_smmu_ops);
+#ifdef CONFIG_ARM_AMBA
if (!iommu_present(&amba_bustype))
bus_set_iommu(&amba_bustype, &arm_smmu_ops);
+#endif
return 0;
}
return 0;
}
+/*
+ * DO NOT change the device Ids. The naming is intentionally specific as both
+ * the PMIC and CODEC parts of this chip are instantiated separately as I2C
+ * devices (both have configurable I2C addresses, and are to all intents and
+ * purposes separate). As a result there are specific DA9055 ids for PMIC
+ * and CODEC, which must be different to operate together.
+ */
static struct i2c_device_id da9055_i2c_id[] = {
- {"da9055", 0},
+ {"da9055-pmic", 0},
{ }
};
+MODULE_DEVICE_TABLE(i2c, da9055_i2c_id);
static struct i2c_driver da9055_i2c_driver = {
.probe = da9055_i2c_probe,
.remove = da9055_i2c_remove,
.id_table = da9055_i2c_id,
.driver = {
- .name = "da9055",
+ .name = "da9055-pmic",
.owner = THIS_MODULE,
},
};
#define PCIE_DEBUG_CTRL 0x1a60
#define PCIE_DEBUG_SOFT_RESET BIT(20)
-/*
- * This product ID is registered by Marvell, and used when the Marvell
- * SoC is not the root complex, but an endpoint on the PCIe bus. It is
- * therefore safe to re-use this PCI ID for our emulated PCI-to-PCI
- * bridge.
- */
-#define MARVELL_EMULATED_PCI_PCI_BRIDGE_ID 0x7846
-
/* PCI configuration space of a PCI-to-PCI bridge */
struct mvebu_sw_pci_bridge {
u16 vendor;
bridge->class = PCI_CLASS_BRIDGE_PCI;
bridge->vendor = PCI_VENDOR_ID_MARVELL;
- bridge->device = MARVELL_EMULATED_PCI_PCI_BRIDGE_ID;
+ bridge->device = mvebu_readl(port, PCIE_DEV_ID_OFF) >> 16;
+ bridge->revision = mvebu_readl(port, PCIE_DEV_REV_OFF) & 0xff;
bridge->header_type = PCI_HEADER_TYPE_BRIDGE;
bridge->cache_line_size = 0x10;
return -ENOMEM;
list_for_each_entry(entry, &pdev->msi_list, list) {
char *name = kmalloc(20, GFP_KERNEL);
+ if (!name)
+ goto error_attrs;
+
msi_dev_attr = kzalloc(sizeof(*msi_dev_attr), GFP_KERNEL);
- if (!msi_dev_attr)
+ if (!msi_dev_attr) {
+ kfree(name);
goto error_attrs;
+ }
+
sprintf(name, "%d", entry->irq);
sysfs_attr_init(&msi_dev_attr->attr);
msi_dev_attr->attr.name = name;
++count;
msi_attr = msi_attrs[count];
}
+ kfree(msi_attrs);
return ret;
}
/**
* pci_msix_vec_count - return the number of device's MSI-X table entries
* @dev: pointer to the pci_dev data structure of MSI-X device function
-
* This function returns the number of device's MSI-X table entries and
* therefore the number of MSI-X vectors device is capable of sending.
* It returns a negative errno if the device is not capable of sending MSI-X
static int do_pci_enable_device(struct pci_dev *dev, int bars)
{
int err;
+ u16 cmd;
+ u8 pin;
err = pci_set_power_state(dev, PCI_D0);
if (err < 0 && err != -EIO)
return err;
pci_fixup_device(pci_fixup_enable, dev);
+ pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin);
+ if (pin) {
+ pci_read_config_word(dev, PCI_COMMAND, &cmd);
+ if (cmd & PCI_COMMAND_INTX_DISABLE)
+ pci_write_config_word(dev, PCI_COMMAND,
+ cmd & ~PCI_COMMAND_INTX_DISABLE);
+ }
+
return 0;
}
#include <linux/lockd/bind.h>
#include <linux/nfs_mount.h>
#include <linux/freezer.h>
+#include <linux/xattr.h>
#include "iostat.h"
#include "internal.h"
*
* The ID of the root cgroup is always 0, and a new cgroup
* will be assigned with a smallest available ID.
+ *
+ * Allocating/Removing ID must be protected by cgroup_mutex.
*/
int id;
void pci_restore_msi_state(struct pci_dev *dev);
int pci_msi_enabled(void);
int pci_enable_msi_range(struct pci_dev *dev, int minvec, int maxvec);
+static inline int pci_enable_msi_exact(struct pci_dev *dev, int nvec)
+{
+ int rc = pci_enable_msi_range(dev, nvec, nvec);
+ if (rc < 0)
+ return rc;
+ return 0;
+}
int pci_enable_msix_range(struct pci_dev *dev, struct msix_entry *entries,
int minvec, int maxvec);
+static inline int pci_enable_msix_exact(struct pci_dev *dev,
+ struct msix_entry *entries, int nvec)
+{
+ int rc = pci_enable_msix_range(dev, entries, nvec, nvec);
+ if (rc < 0)
+ return rc;
+ return 0;
+}
#else
static inline int pci_msi_vec_count(struct pci_dev *dev) { return -ENOSYS; }
static inline int pci_enable_msi_block(struct pci_dev *dev, int nvec)
static inline int pci_enable_msi_range(struct pci_dev *dev, int minvec,
int maxvec)
{ return -ENOSYS; }
+static inline int pci_enable_msi_exact(struct pci_dev *dev, int nvec)
+{ return -ENOSYS; }
static inline int pci_enable_msix_range(struct pci_dev *dev,
struct msix_entry *entries, int minvec, int maxvec)
{ return -ENOSYS; }
+static inline int pci_enable_msix_exact(struct pci_dev *dev,
+ struct msix_entry *entries, int nvec)
+{ return -ENOSYS; }
#endif
#ifdef CONFIG_PCIEPORTBUS
static struct lock_class_key __key; \
const char *__lock_name; \
\
- if (__builtin_constant_p(fmt)) \
- __lock_name = (fmt); \
- else \
- __lock_name = #fmt; \
+ __lock_name = #fmt#args; \
\
__alloc_workqueue_key((fmt), (flags), (max_active), \
&__key, __lock_name, ##args); \
* per-subsystem and moved to css->id so that lookups are
* successful until the target css is released.
*/
+ mutex_lock(&cgroup_mutex);
idr_remove(&cgrp->root->cgroup_idr, cgrp->id);
+ mutex_unlock(&cgroup_mutex);
cgrp->id = -1;
call_rcu(&cgrp->rcu_head, cgroup_free_rcu);
mutex_lock(&cgroup_mutex);
mutex_lock(&cgroup_root_mutex);
- root_cgrp->id = idr_alloc(&root->cgroup_idr, root_cgrp,
- 0, 1, GFP_KERNEL);
- if (root_cgrp->id < 0)
+ ret = idr_alloc(&root->cgroup_idr, root_cgrp, 0, 1, GFP_KERNEL);
+ if (ret < 0)
goto unlock_drop;
+ root_cgrp->id = ret;
/* Check for name clashes with existing mounts */
ret = -EBUSY;
*/
update_before = cgroup_serial_nr_next;
- mutex_unlock(&cgroup_mutex);
-
/* add/rm files for all cgroups created before */
- rcu_read_lock();
css_for_each_descendant_pre(css, cgroup_css(root, ss)) {
struct cgroup *cgrp = css->cgroup;
inode = cgrp->dentry->d_inode;
dget(cgrp->dentry);
- rcu_read_unlock();
-
dput(prev);
prev = cgrp->dentry;
+ mutex_unlock(&cgroup_mutex);
mutex_lock(&inode->i_mutex);
mutex_lock(&cgroup_mutex);
if (cgrp->serial_nr < update_before && !cgroup_is_dead(cgrp))
ret = cgroup_addrm_files(cgrp, cfts, is_add);
- mutex_unlock(&cgroup_mutex);
mutex_unlock(&inode->i_mutex);
-
- rcu_read_lock();
if (ret)
break;
}
- rcu_read_unlock();
+ mutex_unlock(&cgroup_mutex);
dput(prev);
deactivate_super(sb);
return ret;
* We should check if the process is exiting, otherwise
* it will race with cgroup_exit() in that the list
* entry won't be deleted though the process has exited.
+ * Do it while holding siglock so that we don't end up
+ * racing against cgroup_exit().
*/
+ spin_lock_irq(&p->sighand->siglock);
if (!(p->flags & PF_EXITING) && list_empty(&p->cg_list))
list_add(&p->cg_list, &task_css_set(p)->tasks);
+ spin_unlock_irq(&p->sighand->siglock);
+
task_unlock(p);
} while_each_thread(g, p);
read_unlock(&tasklist_lock);
struct cgroup *cgrp;
struct cgroup_name *name;
struct cgroupfs_root *root = parent->root;
- int ssid, err = 0;
+ int ssid, err;
struct cgroup_subsys *ss;
struct super_block *sb = root->sb;
return -ENOMEM;
name = cgroup_alloc_name(dentry);
- if (!name)
+ if (!name) {
+ err = -ENOMEM;
goto err_free_cgrp;
+ }
rcu_assign_pointer(cgrp->name, name);
- /*
- * Temporarily set the pointer to NULL, so idr_find() won't return
- * a half-baked cgroup.
- */
- cgrp->id = idr_alloc(&root->cgroup_idr, NULL, 1, 0, GFP_KERNEL);
- if (cgrp->id < 0)
- goto err_free_name;
-
/*
* Only live parents can have children. Note that the liveliness
* check isn't strictly necessary because cgroup_mkdir() and
*/
if (!cgroup_lock_live_group(parent)) {
err = -ENODEV;
- goto err_free_id;
+ goto err_free_name;
+ }
+
+ /*
+ * Temporarily set the pointer to NULL, so idr_find() won't return
+ * a half-baked cgroup.
+ */
+ cgrp->id = idr_alloc(&root->cgroup_idr, NULL, 1, 0, GFP_KERNEL);
+ if (cgrp->id < 0) {
+ err = -ENOMEM;
+ goto err_unlock;
}
/* Grab a reference on the superblock so the hierarchy doesn't
*/
err = cgroup_create_file(dentry, S_IFDIR | mode, sb);
if (err < 0)
- goto err_unlock;
+ goto err_free_id;
lockdep_assert_held(&dentry->d_inode->i_mutex);
cgrp->serial_nr = cgroup_serial_nr_next++;
return 0;
-err_unlock:
- mutex_unlock(&cgroup_mutex);
- /* Release the reference count that we took on the superblock */
- deactivate_super(sb);
err_free_id:
idr_remove(&root->cgroup_idr, cgrp->id);
+ /* Release the reference count that we took on the superblock */
+ deactivate_super(sb);
+err_unlock:
+ mutex_unlock(&cgroup_mutex);
err_free_name:
kfree(rcu_dereference_raw(cgrp->name));
err_free_cgrp:
#include <linux/kbd_kern.h>
#include <linux/vt.h>
#include <linux/module.h>
+#include <linux/slab.h>
#include "power.h"
#define SUSPEND_CONSOLE (MAX_NR_CONSOLES-1)
*
* When there is no mapping defined for the user-namespace uid
* pair INVALID_UID is returned. Callers are expected to test
- * for and handle handle INVALID_UID being returned. INVALID_UID
+ * for and handle INVALID_UID being returned. INVALID_UID
* may be tested for using uid_valid().
*/
kuid_t make_kuid(struct user_namespace *ns, uid_t uid)
if (worker->flags & WORKER_IDLE)
pool->nr_idle--;
+ /*
+ * Once WORKER_DIE is set, the kworker may destroy itself at any
+ * point. Pin to ensure the task stays until we're done with it.
+ */
+ get_task_struct(worker->task);
+
list_del_init(&worker->entry);
worker->flags |= WORKER_DIE;
spin_unlock_irq(&pool->lock);
kthread_stop(worker->task);
+ put_task_struct(worker->task);
kfree(worker);
spin_lock_irq(&pool->lock);
#include <linux/mm.h>
#include <linux/vmstat.h>
#include <linux/eventfd.h>
+#include <linux/slab.h>
#include <linux/swap.h>
#include <linux/printk.h>
#include <linux/vmpressure.h>
return false;
}
-/*
- * PCM stuffs
- */
-static void ca0132_setup_stream(struct hda_codec *codec, hda_nid_t nid,
- u32 stream_tag,
- int channel_id, int format)
-{
- unsigned int oldval, newval;
-
- if (!nid)
- return;
-
- snd_printdd(
- "ca0132_setup_stream: NID=0x%x, stream=0x%x, "
- "channel=%d, format=0x%x\n",
- nid, stream_tag, channel_id, format);
-
- /* update the format-id if changed */
- oldval = snd_hda_codec_read(codec, nid, 0,
- AC_VERB_GET_STREAM_FORMAT,
- 0);
- if (oldval != format) {
- msleep(20);
- snd_hda_codec_write(codec, nid, 0,
- AC_VERB_SET_STREAM_FORMAT,
- format);
- }
-
- oldval = snd_hda_codec_read(codec, nid, 0, AC_VERB_GET_CONV, 0);
- newval = (stream_tag << 4) | channel_id;
- if (oldval != newval) {
- snd_hda_codec_write(codec, nid, 0,
- AC_VERB_SET_CHANNEL_STREAMID,
- newval);
- }
-}
-
-static void ca0132_cleanup_stream(struct hda_codec *codec, hda_nid_t nid)
-{
- unsigned int val;
-
- if (!nid)
- return;
-
- snd_printdd(KERN_INFO "ca0132_cleanup_stream: NID=0x%x\n", nid);
-
- val = snd_hda_codec_read(codec, nid, 0, AC_VERB_GET_CONV, 0);
- if (!val)
- return;
-
- snd_hda_codec_write(codec, nid, 0, AC_VERB_SET_STREAM_FORMAT, 0);
- snd_hda_codec_write(codec, nid, 0, AC_VERB_SET_CHANNEL_STREAMID, 0);
-}
-
/*
* PCM callbacks
*/
{
struct ca0132_spec *spec = codec->spec;
- ca0132_setup_stream(codec, spec->dacs[0], stream_tag, 0, format);
+ snd_hda_codec_setup_stream(codec, spec->dacs[0], stream_tag, 0, format);
return 0;
}
if (spec->effects_switch[PLAY_ENHANCEMENT - EFFECT_START_NID])
msleep(50);
- ca0132_cleanup_stream(codec, spec->dacs[0]);
+ snd_hda_codec_cleanup_stream(codec, spec->dacs[0]);
return 0;
}
unsigned int format,
struct snd_pcm_substream *substream)
{
- struct ca0132_spec *spec = codec->spec;
-
- ca0132_setup_stream(codec, spec->adcs[substream->number],
- stream_tag, 0, format);
+ snd_hda_codec_setup_stream(codec, hinfo->nid,
+ stream_tag, 0, format);
return 0;
}
if (spec->dsp_state == DSP_DOWNLOADING)
return 0;
- ca0132_cleanup_stream(codec, hinfo->nid);
+ snd_hda_codec_cleanup_stream(codec, hinfo->nid);
return 0;
}
return err;
codec->patch_ops = ca0132_patch_ops;
+ codec->pcm_format_first = 1;
+ codec->no_sticky_stream = 1;
return 0;
}
SND_PCI_QUIRK(0x1028, 0x0651, "Dell", ALC255_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x0652, "Dell", ALC255_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x0653, "Dell", ALC255_FIXUP_DELL1_MIC_NO_PRESENCE),
+ SND_PCI_QUIRK(0x1028, 0x0657, "Dell", ALC255_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x0658, "Dell", ALC269_FIXUP_DELL1_MIC_NO_PRESENCE),
+ SND_PCI_QUIRK(0x1028, 0x065f, "Dell", ALC255_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x0662, "Dell", ALC255_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x15cc, "Dell X5 Precision", ALC269_FIXUP_DELL2_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x15cd, "Dell X5 Precision", ALC269_FIXUP_DELL2_MIC_NO_PRESENCE),
STAC_DELL_M6_BOTH,
STAC_DELL_EQ,
STAC_ALIENWARE_M17X,
+ STAC_92HD89XX_HP_FRONT_JACK,
STAC_92HD73XX_MODELS
};
{}
};
+static const struct hda_pintbl stac92hd89xx_hp_front_jack_pin_configs[] = {
+ { 0x0a, 0x02214030 },
+ { 0x0b, 0x02A19010 },
+ {}
+};
+
static void stac92hd73xx_fixup_ref(struct hda_codec *codec,
const struct hda_fixup *fix, int action)
{
[STAC_92HD73XX_NO_JD] = {
.type = HDA_FIXUP_FUNC,
.v.func = stac92hd73xx_fixup_no_jd,
+ },
+ [STAC_92HD89XX_HP_FRONT_JACK] = {
+ .type = HDA_FIXUP_PINS,
+ .v.pins = stac92hd89xx_hp_front_jack_pin_configs,
}
};
"Alienware M17x", STAC_ALIENWARE_M17X),
SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x0490,
"Alienware M17x R3", STAC_DELL_EQ),
+ SND_PCI_QUIRK(PCI_VENDOR_ID_HP, 0x2b17,
+ "unknown HP", STAC_92HD89XX_HP_FRONT_JACK),
{} /* terminator */
};
config SND_BF5XX_SOC_SSM2602
tristate "SoC SSM2602 Audio Codec Add-On Card support"
- depends on SND_BF5XX_I2S && (SPI_MASTER || I2C)
+ depends on SND_BF5XX_I2S && SND_SOC_I2C_AND_SPI
select SND_BF5XX_SOC_I2S if !BF60x
select SND_BF6XX_SOC_I2S if BF60x
select SND_SOC_SSM2602
config SND_SOC_BFIN_EVAL_ADAU1701
tristate "Support for the EVAL-ADAU1701MINIZ board on Blackfin eval boards"
- depends on SND_BF5XX_I2S
+ depends on SND_BF5XX_I2S && I2C
select SND_BF5XX_SOC_I2S
select SND_SOC_ADAU1701
- select I2C
help
Say Y if you want to add support for the Analog Devices EVAL-ADAU1701MINIZ
board connected to one of the Blackfin evaluation boards like the
config SND_SOC_BFIN_EVAL_ADAV80X
tristate "Support for the EVAL-ADAV80X boards on Blackfin eval boards"
- depends on SND_BF5XX_I2S && (SPI_MASTER || I2C)
+ depends on SND_BF5XX_I2S && SND_SOC_I2C_AND_SPI
select SND_BF5XX_SOC_I2S
select SND_SOC_ADAV80X
help
config SND_BF5XX_SOC_AD1836
tristate "SoC AD1836 Audio support for BF5xx"
- depends on SND_BF5XX_I2S
+ depends on SND_BF5XX_I2S && SPI_MASTER
select SND_BF5XX_SOC_I2S
select SND_SOC_AD1836
help
config SND_BF5XX_SOC_AD193X
tristate "SoC AD193X Audio support for Blackfin"
- depends on SND_BF5XX_I2S
+ depends on SND_BF5XX_I2S && SND_SOC_I2C_AND_SPI
select SND_BF5XX_SOC_I2S
select SND_SOC_AD193X
help
return 0;
}
+/*
+ * DO NOT change the device Ids. The naming is intentionally specific as both
+ * the CODEC and PMIC parts of this chip are instantiated separately as I2C
+ * devices (both have configurable I2C addresses, and are to all intents and
+ * purposes separate). As a result there are specific DA9055 Ids for CODEC
+ * and PMIC, which must be different to operate together.
+ */
static const struct i2c_device_id da9055_i2c_id[] = {
- { "da9055", 0 },
+ { "da9055-codec", 0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, da9055_i2c_id);
/* I2C codec control layer */
static struct i2c_driver da9055_i2c_driver = {
.driver = {
- .name = "da9055",
+ .name = "da9055-codec",
.owner = THIS_MODULE,
},
.probe = da9055_i2c_probe,
case M98090_REG_RECORD_TDM_SLOT:
case M98090_REG_SAMPLE_RATE:
case M98090_REG_DMIC34_BIQUAD_BASE ... M98090_REG_DMIC34_BIQUAD_BASE + 0x0E:
+ case M98090_REG_REVISION_ID:
return true;
default:
return false;
switch (level) {
case SND_SOC_BIAS_ON:
- if (codec->dapm.bias_level == SND_SOC_BIAS_OFF) {
- ret = regcache_sync(max98090->regmap);
-
- if (ret != 0) {
- dev_err(codec->dev,
- "Failed to sync cache: %d\n", ret);
- return ret;
- }
- }
-
if (max98090->jack_state == M98090_JACK_STATE_HEADSET) {
/*
* Set to normal bias level.
break;
case SND_SOC_BIAS_STANDBY:
+ if (codec->dapm.bias_level == SND_SOC_BIAS_OFF) {
+ ret = regcache_sync(max98090->regmap);
+ if (ret != 0) {
+ dev_err(codec->dev,
+ "Failed to sync cache: %d\n", ret);
+ return ret;
+ }
+ }
+ break;
+
case SND_SOC_BIAS_OFF:
/* Set internal pull-up to lowest power mode */
snd_soc_update_bits(codec, M98090_REG_JACK_DETECT,
#ifdef CONFIG_ACPI
static struct acpi_device_id rt5640_acpi_match[] = {
{ "INT33CA", 0 },
+ { "10EC5640", 0 },
{ },
};
MODULE_DEVICE_TABLE(acpi, rt5640_acpi_match);
struct wm8993_priv *wm8993 = snd_soc_codec_get_drvdata(codec);
wm8993_set_bias_level(codec, SND_SOC_BIAS_OFF);
- regulator_bulk_free(ARRAY_SIZE(wm8993->supplies), wm8993->supplies);
return 0;
}
.driver = {
.name = "davinci_evm",
.owner = THIS_MODULE,
+ .pm = &snd_soc_pm_ops,
.of_match_table = of_match_ptr(davinci_evm_dt_ids),
},
};
unsigned int fmt)
{
struct davinci_mcasp *mcasp = snd_soc_dai_get_drvdata(cpu_dai);
+ int ret = 0;
+ pm_runtime_get_sync(mcasp->dev);
switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
case SND_SOC_DAIFMT_DSP_B:
case SND_SOC_DAIFMT_AC97:
break;
default:
- return -EINVAL;
+ ret = -EINVAL;
+ goto out;
}
switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
break;
default:
- return -EINVAL;
+ ret = -EINVAL;
+ break;
}
-
- return 0;
+out:
+ pm_runtime_put_sync(mcasp->dev);
+ return ret;
}
static int davinci_mcasp_set_clkdiv(struct snd_soc_dai *dai, int div_id, int div)
return 0;
}
-static int davinci_hw_common_param(struct davinci_mcasp *mcasp, int stream,
+static int mcasp_common_hw_param(struct davinci_mcasp *mcasp, int stream,
int channels)
{
int i;
return 0;
}
-static void davinci_hw_param(struct davinci_mcasp *mcasp, int stream)
+static int mcasp_i2s_hw_param(struct davinci_mcasp *mcasp, int stream)
{
int i, active_slots;
u32 mask = 0;
u32 busel = 0;
+ if ((mcasp->tdm_slots < 2) || (mcasp->tdm_slots > 32)) {
+ dev_err(mcasp->dev, "tdm slot %d not supported\n",
+ mcasp->tdm_slots);
+ return -EINVAL;
+ }
+
active_slots = (mcasp->tdm_slots > 31) ? 32 : mcasp->tdm_slots;
for (i = 0; i < active_slots; i++)
mask |= (1 << i);
if (!mcasp->dat_port)
busel = TXSEL;
- if (stream == SNDRV_PCM_STREAM_PLAYBACK) {
- /* bit stream is MSB first with no delay */
- /* DSP_B mode */
- mcasp_set_reg(mcasp, DAVINCI_MCASP_TXTDM_REG, mask);
- mcasp_set_bits(mcasp, DAVINCI_MCASP_TXFMT_REG, busel | TXORD);
-
- if ((mcasp->tdm_slots >= 2) && (mcasp->tdm_slots <= 32))
- mcasp_mod_bits(mcasp, DAVINCI_MCASP_TXFMCTL_REG,
- FSXMOD(mcasp->tdm_slots), FSXMOD(0x1FF));
- else
- printk(KERN_ERR "playback tdm slot %d not supported\n",
- mcasp->tdm_slots);
- } else {
- /* bit stream is MSB first with no delay */
- /* DSP_B mode */
- mcasp_set_bits(mcasp, DAVINCI_MCASP_RXFMT_REG, busel | RXORD);
- mcasp_set_reg(mcasp, DAVINCI_MCASP_RXTDM_REG, mask);
-
- if ((mcasp->tdm_slots >= 2) && (mcasp->tdm_slots <= 32))
- mcasp_mod_bits(mcasp, DAVINCI_MCASP_RXFMCTL_REG,
- FSRMOD(mcasp->tdm_slots), FSRMOD(0x1FF));
- else
- printk(KERN_ERR "capture tdm slot %d not supported\n",
- mcasp->tdm_slots);
- }
+ mcasp_set_reg(mcasp, DAVINCI_MCASP_TXTDM_REG, mask);
+ mcasp_set_bits(mcasp, DAVINCI_MCASP_TXFMT_REG, busel | TXORD);
+ mcasp_mod_bits(mcasp, DAVINCI_MCASP_TXFMCTL_REG,
+ FSXMOD(mcasp->tdm_slots), FSXMOD(0x1FF));
+
+ mcasp_set_reg(mcasp, DAVINCI_MCASP_RXTDM_REG, mask);
+ mcasp_set_bits(mcasp, DAVINCI_MCASP_RXFMT_REG, busel | RXORD);
+ mcasp_mod_bits(mcasp, DAVINCI_MCASP_RXFMCTL_REG,
+ FSRMOD(mcasp->tdm_slots), FSRMOD(0x1FF));
+
+ return 0;
}
/* S/PDIF */
-static void davinci_hw_dit_param(struct davinci_mcasp *mcasp)
+static int mcasp_dit_hw_param(struct davinci_mcasp *mcasp)
{
/* Set the TX format : 24 bit right rotation, 32 bit slot, Pad 0
and LSB first */
/* Enable the DIT */
mcasp_set_bits(mcasp, DAVINCI_MCASP_TXDITCTL_REG, DITEN);
+
+ return 0;
}
static int davinci_mcasp_hw_params(struct snd_pcm_substream *substream,
u8 slots = mcasp->tdm_slots;
u8 active_serializers;
int channels;
+ int ret;
struct snd_interval *pcm_channels = hw_param_interval(params,
SNDRV_PCM_HW_PARAM_CHANNELS);
channels = pcm_channels->min;
active_serializers = (channels + slots - 1) / slots;
- if (davinci_hw_common_param(mcasp, substream->stream, channels) == -EINVAL)
+ if (mcasp_common_hw_param(mcasp, substream->stream, channels) == -EINVAL)
return -EINVAL;
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
fifo_level = mcasp->txnumevt * active_serializers;
fifo_level = mcasp->rxnumevt * active_serializers;
if (mcasp->op_mode == DAVINCI_MCASP_DIT_MODE)
- davinci_hw_dit_param(mcasp);
+ ret = mcasp_dit_hw_param(mcasp);
else
- davinci_hw_param(mcasp, substream->stream);
+ ret = mcasp_i2s_hw_param(mcasp, substream->stream);
+
+ if (ret)
+ return ret;
switch (params_format(params)) {
case SNDRV_PCM_FORMAT_U8:
case SNDRV_PCM_TRIGGER_RESUME:
case SNDRV_PCM_TRIGGER_START:
case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
- ret = pm_runtime_get_sync(mcasp->dev);
- if (IS_ERR_VALUE(ret))
- dev_err(mcasp->dev, "pm_runtime_get_sync() failed\n");
davinci_mcasp_start(mcasp, substream->stream);
break;
-
case SNDRV_PCM_TRIGGER_SUSPEND:
- davinci_mcasp_stop(mcasp, substream->stream);
- ret = pm_runtime_put_sync(mcasp->dev);
- if (IS_ERR_VALUE(ret))
- dev_err(mcasp->dev, "pm_runtime_put_sync() failed\n");
- break;
-
case SNDRV_PCM_TRIGGER_STOP:
case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
davinci_mcasp_stop(mcasp, substream->stream);
regmap_update_bits(esai_priv->regmap, REG_ESAI_TSMA,
ESAI_xSMA_xS_MASK, ESAI_xSMA_xS(tx_mask));
regmap_update_bits(esai_priv->regmap, REG_ESAI_TSMB,
- ESAI_xSMA_xS_MASK, ESAI_xSMB_xS(tx_mask));
+ ESAI_xSMB_xS_MASK, ESAI_xSMB_xS(tx_mask));
regmap_update_bits(esai_priv->regmap, REG_ESAI_RCCR,
ESAI_xCCR_xDC_MASK, ESAI_xCCR_xDC(slots));
regmap_update_bits(esai_priv->regmap, REG_ESAI_RSMA,
ESAI_xSMA_xS_MASK, ESAI_xSMA_xS(rx_mask));
regmap_update_bits(esai_priv->regmap, REG_ESAI_RSMB,
- ESAI_xSMA_xS_MASK, ESAI_xSMB_xS(rx_mask));
+ ESAI_xSMB_xS_MASK, ESAI_xSMB_xS(rx_mask));
esai_priv->slot_width = slot_width;
#define ESAI_xSMB_xS_SHIFT 0
#define ESAI_xSMB_xS_WIDTH 16
#define ESAI_xSMB_xS_MASK (((1 << ESAI_xSMB_xS_WIDTH) - 1) << ESAI_xSMB_xS_SHIFT)
-#define ESAI_xSMB_xS(v) (((v) >> ESAI_xSMA_xS_WIDTH) & ESAI_xSMA_xS_MASK)
+#define ESAI_xSMB_xS(v) (((v) >> ESAI_xSMA_xS_WIDTH) & ESAI_xSMB_xS_MASK)
/* Port C Direction Register -- REG_ESAI_PRRC 0xF8 */
#define ESAI_PRRC_PDC_SHIFT 0
.driver = {
.name = "imx_mc13783",
.owner = THIS_MODULE,
- .pm = &snd_soc_pm_ops,
},
.probe = imx_mc13783_probe,
.remove = imx_mc13783_remove
static int imx_sgtl5000_dai_init(struct snd_soc_pcm_runtime *rtd)
{
- struct imx_sgtl5000_data *data = container_of(rtd->card,
- struct imx_sgtl5000_data, card);
+ struct imx_sgtl5000_data *data = snd_soc_card_get_drvdata(rtd->card);
struct device *dev = rtd->card->dev;
int ret;
data->card.dapm_widgets = imx_sgtl5000_dapm_widgets;
data->card.num_dapm_widgets = ARRAY_SIZE(imx_sgtl5000_dapm_widgets);
+ platform_set_drvdata(pdev, &data->card);
+ snd_soc_card_set_drvdata(&data->card, data);
+
ret = devm_snd_soc_register_card(&pdev->dev, &data->card);
if (ret) {
dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", ret);
goto fail;
}
- platform_set_drvdata(pdev, data);
of_node_put(ssi_np);
of_node_put(codec_np);
static int imx_sgtl5000_remove(struct platform_device *pdev)
{
- struct imx_sgtl5000_data *data = platform_get_drvdata(pdev);
+ struct snd_soc_card *card = platform_get_drvdata(pdev);
+ struct imx_sgtl5000_data *data = snd_soc_card_get_drvdata(card);
clk_put(data->codec_clk);
{
struct snd_soc_dai *codec_dai = card->rtd[0].codec_dai;
struct imx_priv *priv = &card_priv;
- struct imx_wm8962_data *data = platform_get_drvdata(priv->pdev);
+ struct imx_wm8962_data *data = snd_soc_card_get_drvdata(card);
struct device *dev = &priv->pdev->dev;
unsigned int pll_out;
int ret;
{
struct snd_soc_dai *codec_dai = card->rtd[0].codec_dai;
struct imx_priv *priv = &card_priv;
- struct imx_wm8962_data *data = platform_get_drvdata(priv->pdev);
+ struct imx_wm8962_data *data = snd_soc_card_get_drvdata(card);
struct device *dev = &priv->pdev->dev;
int ret;
data->card.late_probe = imx_wm8962_late_probe;
data->card.set_bias_level = imx_wm8962_set_bias_level;
+ platform_set_drvdata(pdev, &data->card);
+ snd_soc_card_set_drvdata(&data->card, data);
+
ret = devm_snd_soc_register_card(&pdev->dev, &data->card);
if (ret) {
dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", ret);
goto clk_fail;
}
- platform_set_drvdata(pdev, data);
of_node_put(ssi_np);
of_node_put(codec_np);
static int imx_wm8962_remove(struct platform_device *pdev)
{
- struct imx_wm8962_data *data = platform_get_drvdata(pdev);
+ struct snd_soc_card *card = platform_get_drvdata(pdev);
+ struct imx_wm8962_data *data = snd_soc_card_get_drvdata(card);
if (!IS_ERR(data->codec_clk))
clk_disable_unprepare(data->codec_clk);
select SND_SOC_WM8750
select SND_S3C2412_SOC_I2S
help
- Sat Y if you want to add support for SoC audio on the Jive.
+ Say Y if you want to add support for SoC audio on the Jive.
config SND_SOC_SAMSUNG_SMDK_WM8580
tristate "SoC I2S Audio support for WM8580 on SMDK"
config SND_SOC_SAMSUNG_SMDK_WM9713
tristate "SoC AC97 Audio support for SMDK with WM9713"
- depends on SND_SOC_SAMSUNG && (MACH_SMDK6410 || MACH_SMDKC100 || MACH_SMDKV210 || MACH_SMDKC110 || MACH_SMDKV310 || MACH_SMDKC210)
+ depends on SND_SOC_SAMSUNG && (MACH_SMDK6410 || MACH_SMDKC100 || MACH_SMDKV210 || MACH_SMDKC110)
select SND_SOC_WM9713
select SND_SAMSUNG_AC97
help
- Sat Y if you want to add support for SoC audio on the SMDK.
+ Say Y if you want to add support for SoC audio on the SMDK.
config SND_SOC_SMARTQ
tristate "SoC I2S Audio support for SmartQ board"
irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
+
+ drvdata = devm_kzalloc(&pdev->dev, sizeof(*drvdata), GFP_KERNEL);
+ if (!drvdata)
+ return -ENOMEM;
+
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
drvdata->base = devm_ioremap_resource(&pdev->dev, r);
if (IS_ERR(drvdata->base))
return PTR_ERR(drvdata->base);
- drvdata = devm_kzalloc(&pdev->dev, sizeof(*drvdata), GFP_KERNEL);
- if (!drvdata)
- return -ENOMEM;
platform_set_drvdata(pdev, drvdata);
drvdata->physbase = r->start;
if (sizeof(drvdata->physbase) > sizeof(r->start) &&
{}
};
+static const struct usbmix_name_map kef_x300a_map[] = {
+ { 10, NULL }, /* firmware locks up (?) when we try to access this FU */
+ { 0 }
+};
+
/*
* Control map entries
*/
.id = USB_ID(0x200c, 0x1018),
.map = ebox44_map,
},
+ {
+ .id = USB_ID(0x27ac, 0x1000),
+ .map = kef_x300a_map,
+ },
{ 0 } /* terminator */
};
projects / linux-2.6-microblaze.git / commitdiff