--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Modified from dw_mmc-hi3798cv200.c
+ *
+ * Copyright (c) 2024 Yang Xiwen <forbidden405@outlook.com>
+ * Copyright (c) 2018 HiSilicon Technologies Co., Ltd.
+ */
+
+#include <linux/clk.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mmc/host.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "dw_mmc.h"
+#include "dw_mmc-pltfm.h"
+
+#define SDMMC_TUNING_CTRL 0x118
+#define SDMMC_TUNING_FIND_EDGE BIT(5)
+
+#define ALL_INT_CLR 0x1ffff
+
+/* DLL ctrl reg */
+#define SAP_DLL_CTRL_DLLMODE BIT(16)
+
+struct dw_mci_hi3798mv200_priv {
+ struct clk *sample_clk;
+ struct clk *drive_clk;
+ struct regmap *crg_reg;
+ u32 sap_dll_offset;
+ struct mmc_clk_phase_map phase_map;
+};
+
+static void dw_mci_hi3798mv200_set_ios(struct dw_mci *host, struct mmc_ios *ios)
+{
+ struct dw_mci_hi3798mv200_priv *priv = host->priv;
+ struct mmc_clk_phase phase = priv->phase_map.phase[ios->timing];
+ u32 val;
+
+ val = mci_readl(host, ENABLE_SHIFT);
+ if (ios->timing == MMC_TIMING_MMC_DDR52
+ || ios->timing == MMC_TIMING_UHS_DDR50)
+ val |= SDMMC_ENABLE_PHASE;
+ else
+ val &= ~SDMMC_ENABLE_PHASE;
+ mci_writel(host, ENABLE_SHIFT, val);
+
+ val = mci_readl(host, DDR_REG);
+ if (ios->timing == MMC_TIMING_MMC_HS400)
+ val |= SDMMC_DDR_HS400;
+ else
+ val &= ~SDMMC_DDR_HS400;
+ mci_writel(host, DDR_REG, val);
+
+ if (clk_set_rate(host->ciu_clk, ios->clock))
+ dev_warn(host->dev, "Failed to set rate to %u\n", ios->clock);
+ else
+ /*
+ * CLK_MUX_ROUND_NEAREST is enabled for this clock
+ * The actual clock rate is not what we set, but a rounded value
+ * so we should get the rate once again
+ */
+ host->bus_hz = clk_get_rate(host->ciu_clk);
+
+ if (phase.valid) {
+ clk_set_phase(priv->drive_clk, phase.out_deg);
+ clk_set_phase(priv->sample_clk, phase.in_deg);
+ } else {
+ dev_warn(host->dev,
+ "The phase entry for timing mode %d is missing in device tree.\n",
+ ios->timing);
+ }
+}
+
+static inline int dw_mci_hi3798mv200_enable_tuning(struct dw_mci_slot *slot)
+{
+ struct dw_mci_hi3798mv200_priv *priv = slot->host->priv;
+
+ return regmap_clear_bits(priv->crg_reg, priv->sap_dll_offset, SAP_DLL_CTRL_DLLMODE);
+}
+
+static inline int dw_mci_hi3798mv200_disable_tuning(struct dw_mci_slot *slot)
+{
+ struct dw_mci_hi3798mv200_priv *priv = slot->host->priv;
+
+ return regmap_set_bits(priv->crg_reg, priv->sap_dll_offset, SAP_DLL_CTRL_DLLMODE);
+}
+
+static int dw_mci_hi3798mv200_execute_tuning_mix_mode(struct dw_mci_slot *slot,
+ u32 opcode)
+{
+ static const int degrees[] = { 0, 45, 90, 135, 180, 225, 270, 315 };
+ struct dw_mci *host = slot->host;
+ struct dw_mci_hi3798mv200_priv *priv = host->priv;
+ int raise_point = -1, fall_point = -1, mid;
+ int err, prev_err = -1;
+ int found = 0;
+ int regval;
+ int i;
+ int ret;
+
+ ret = dw_mci_hi3798mv200_enable_tuning(slot);
+ if (ret < 0)
+ return ret;
+
+ for (i = 0; i < ARRAY_SIZE(degrees); i++) {
+ clk_set_phase(priv->sample_clk, degrees[i]);
+ mci_writel(host, RINTSTS, ALL_INT_CLR);
+
+ /*
+ * HiSilicon implemented a tuning mechanism.
+ * It needs special interaction with the DLL.
+ *
+ * Treat edge(flip) found as an error too.
+ */
+ err = mmc_send_tuning(slot->mmc, opcode, NULL);
+ regval = mci_readl(host, TUNING_CTRL);
+ if (err || (regval & SDMMC_TUNING_FIND_EDGE))
+ err = 1;
+ else
+ found = 1;
+
+ if (i > 0) {
+ if (err && !prev_err)
+ fall_point = i - 1;
+ if (!err && prev_err)
+ raise_point = i;
+ }
+
+ if (raise_point != -1 && fall_point != -1)
+ goto tuning_out;
+
+ prev_err = err;
+ err = 0;
+ }
+
+tuning_out:
+ ret = dw_mci_hi3798mv200_disable_tuning(slot);
+ if (ret < 0)
+ return ret;
+
+ if (found) {
+ if (raise_point == -1)
+ raise_point = 0;
+ if (fall_point == -1)
+ fall_point = ARRAY_SIZE(degrees) - 1;
+ if (fall_point < raise_point) {
+ if ((raise_point + fall_point) >
+ (ARRAY_SIZE(degrees) - 1))
+ mid = fall_point / 2;
+ else
+ mid = (raise_point + ARRAY_SIZE(degrees) - 1) / 2;
+ } else {
+ mid = (raise_point + fall_point) / 2;
+ }
+
+ /*
+ * We don't care what timing we are tuning for,
+ * simply use the same phase for all timing needs tuning.
+ */
+ priv->phase_map.phase[MMC_TIMING_MMC_HS200].in_deg = degrees[mid];
+ priv->phase_map.phase[MMC_TIMING_MMC_HS400].in_deg = degrees[mid];
+ priv->phase_map.phase[MMC_TIMING_UHS_SDR104].in_deg = degrees[mid];
+
+ clk_set_phase(priv->sample_clk, degrees[mid]);
+ dev_dbg(host->dev, "Tuning clk_sample[%d, %d], set[%d]\n",
+ raise_point, fall_point, degrees[mid]);
+ ret = 0;
+ } else {
+ dev_err(host->dev, "No valid clk_sample shift!\n");
+ ret = -EINVAL;
+ }
+
+ mci_writel(host, RINTSTS, ALL_INT_CLR);
+
+ return ret;
+}
+
+static int dw_mci_hi3798mv200_init(struct dw_mci *host)
+{
+ struct dw_mci_hi3798mv200_priv *priv;
+ struct device_node *np = host->dev->of_node;
+ int ret;
+
+ priv = devm_kzalloc(host->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ mmc_of_parse_clk_phase(host->dev, &priv->phase_map);
+
+ priv->sample_clk = devm_clk_get_enabled(host->dev, "ciu-sample");
+ if (IS_ERR(priv->sample_clk))
+ return dev_err_probe(host->dev, PTR_ERR(priv->sample_clk),
+ "failed to get enabled ciu-sample clock\n");
+
+ priv->drive_clk = devm_clk_get_enabled(host->dev, "ciu-drive");
+ if (IS_ERR(priv->drive_clk))
+ return dev_err_probe(host->dev, PTR_ERR(priv->drive_clk),
+ "failed to get enabled ciu-drive clock\n");
+
+ priv->crg_reg = syscon_regmap_lookup_by_phandle(np, "hisilicon,sap-dll-reg");
+ if (IS_ERR(priv->crg_reg))
+ return dev_err_probe(host->dev, PTR_ERR(priv->crg_reg),
+ "failed to get CRG reg\n");
+
+ ret = of_property_read_u32_index(np, "hisilicon,sap-dll-reg", 1, &priv->sap_dll_offset);
+ if (ret)
+ return dev_err_probe(host->dev, ret, "failed to get sample DLL register offset\n");
+
+ host->priv = priv;
+ return 0;
+}
+
+static const struct dw_mci_drv_data hi3798mv200_data = {
+ .common_caps = MMC_CAP_CMD23,
+ .init = dw_mci_hi3798mv200_init,
+ .set_ios = dw_mci_hi3798mv200_set_ios,
+ .execute_tuning = dw_mci_hi3798mv200_execute_tuning_mix_mode,
+};
+
+static const struct of_device_id dw_mci_hi3798mv200_match[] = {
+ { .compatible = "hisilicon,hi3798mv200-dw-mshc" },
+ {},
+};
+
+static int dw_mci_hi3798mv200_probe(struct platform_device *pdev)
+{
+ return dw_mci_pltfm_register(pdev, &hi3798mv200_data);
+}
+
+static void dw_mci_hi3798mv200_remove(struct platform_device *pdev)
+{
+ dw_mci_pltfm_remove(pdev);
+}
+
+MODULE_DEVICE_TABLE(of, dw_mci_hi3798mv200_match);
+static struct platform_driver dw_mci_hi3798mv200_driver = {
+ .probe = dw_mci_hi3798mv200_probe,
+ .remove_new = dw_mci_hi3798mv200_remove,
+ .driver = {
+ .name = "dwmmc_hi3798mv200",
+ .probe_type = PROBE_PREFER_ASYNCHRONOUS,
+ .of_match_table = dw_mci_hi3798mv200_match,
+ },
+};
+module_platform_driver(dw_mci_hi3798mv200_driver);
+
+MODULE_DESCRIPTION("HiSilicon Hi3798MV200 Specific DW-MSHC Driver Extension");
+MODULE_LICENSE("GPL");
projects / linux-2.6-microblaze.git / commitdiff