ARM: dts: imx: ventana: fix DTC warnings

Remove the sky2 ethernet device node from the pcie controller which was
invalid to begin with.

The original intent was to allow the bootloader to populate the MAC via
dt but this requires the PCI bus topology to be complete in dt as well
and as these boards have an expansion connector that topology is dynamic
and can't be represented here.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

diff --git a/arch/arm/boot/dts/imx6q-gw5400-a.dts b/arch/arm/boot/dts/imx6q-gw5400-a.dts
index 8e84713..687ab91 100644 (file)
--- a/arch/arm/boot/dts/imx6q-gw5400-a.dts
+++ b/arch/arm/boot/dts/imx6q-gw5400-a.dts
@@ -19,7 +19,6 @@
 
        /* these are used by bootloader for disabling nodes */
        aliases {
-               ethernet1 = &eth1;
                i2c0 = &i2c1;
                i2c1 = &i2c2;
                i2c2 = &i2c3;
@@ -347,10 +346,6 @@
 &pcie {
        reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
        status = "okay";
-
-       eth1: sky2@8 { /* MAC/PHY on bus 8 */
-               compatible = "marvell,sky2";
-       };
 };
 
 &ssi1 {

diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
index a208e7e..5bc6ed1 100644 (file)
--- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
@@ -14,7 +14,6 @@
 / {
        /* these are used by bootloader for disabling nodes */
        aliases {
-               ethernet1 = &eth1;
                led0 = &led0;
                led1 = &led1;
                led2 = &led2;
@@ -342,10 +341,6 @@
        pinctrl-0 = <&pinctrl_pcie>;
        reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
        status = "okay";
-
-       eth1: sky2@8 { /* MAC/PHY on bus 8 */
-               compatible = "marvell,sky2";
-       };
 };
 
 &pwm2 {

diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
index 968fda9..66fcf83 100644 (file)
--- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
@@ -14,7 +14,6 @@
 / {
        /* these are used by bootloader for disabling nodes */
        aliases {
-               ethernet1 = &eth1;
                led0 = &led0;
                led1 = &led1;
                led2 = &led2;
@@ -379,10 +378,6 @@
        pinctrl-0 = <&pinctrl_pcie>;
        reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
        status = "okay";
-
-       eth1: sky2@8 { /* MAC/PHY on bus 8 */
-               compatible = "marvell,sky2";
-       };
 };
 
 &pwm1 {