+++ /dev/null
-/* ewrk3.c: A DIGITAL EtherWORKS 3 ethernet driver for Linux.
-
- Written 1994 by David C. Davies.
-
- Copyright 1994 Digital Equipment Corporation.
-
- This software may be used and distributed according to the terms of
- the GNU General Public License, incorporated herein by reference.
-
- This driver is written for the Digital Equipment Corporation series
- of EtherWORKS ethernet cards:
-
- DE203 Turbo (BNC)
- DE204 Turbo (TP)
- DE205 Turbo (TP BNC)
-
- The driver has been tested on a relatively busy network using the DE205
- card and benchmarked with 'ttcp': it transferred 16M of data at 975kB/s
- (7.8Mb/s) to a DECstation 5000/200.
-
- The author may be reached at davies@maniac.ultranet.com.
-
- =========================================================================
- This driver has been written substantially from scratch, although its
- inheritance of style and stack interface from 'depca.c' and in turn from
- Donald Becker's 'lance.c' should be obvious.
-
- The DE203/4/5 boards all use a new proprietary chip in place of the
- LANCE chip used in prior cards (DEPCA, DE100, DE200/1/2, DE210, DE422).
- Use the depca.c driver in the standard distribution for the LANCE based
- cards from DIGITAL; this driver will not work with them.
-
- The DE203/4/5 cards have 2 main modes: shared memory and I/O only. I/O
- only makes all the card accesses through I/O transactions and no high
- (shared) memory is used. This mode provides a >48% performance penalty
- and is deprecated in this driver, although allowed to provide initial
- setup when hardstrapped.
-
- The shared memory mode comes in 3 flavours: 2kB, 32kB and 64kB. There is
- no point in using any mode other than the 2kB mode - their performances
- are virtually identical, although the driver has been tested in the 2kB
- and 32kB modes. I would suggest you uncomment the line:
-
- FORCE_2K_MODE;
-
- to allow the driver to configure the card as a 2kB card at your current
- base address, thus leaving more room to clutter your system box with
- other memory hungry boards.
-
- As many ISA and EISA cards can be supported under this driver as you
- wish, limited primarily by the available IRQ lines, rather than by the
- available I/O addresses (24 ISA, 16 EISA). I have checked different
- configurations of multiple depca cards and ewrk3 cards and have not
- found a problem yet (provided you have at least depca.c v0.38) ...
-
- The board IRQ setting must be at an unused IRQ which is auto-probed
- using Donald Becker's autoprobe routines. All these cards are at
- {5,10,11,15}.
-
- No 16MB memory limitation should exist with this driver as DMA is not
- used and the common memory area is in low memory on the network card (my
- current system has 20MB and I've not had problems yet).
-
- The ability to load this driver as a loadable module has been included
- and used extensively during the driver development (to save those long
- reboot sequences). To utilise this ability, you have to do 8 things:
-
- 0) have a copy of the loadable modules code installed on your system.
- 1) copy ewrk3.c from the /linux/drivers/net directory to your favourite
- temporary directory.
- 2) edit the source code near line 1898 to reflect the I/O address and
- IRQ you're using.
- 3) compile ewrk3.c, but include -DMODULE in the command line to ensure
- that the correct bits are compiled (see end of source code).
- 4) if you are wanting to add a new card, goto 5. Otherwise, recompile a
- kernel with the ewrk3 configuration turned off and reboot.
- 5) insmod ewrk3.o
- [Alan Cox: Changed this so you can insmod ewrk3.o irq=x io=y]
- [Adam Kropelin: now accepts irq=x1,x2 io=y1,y2 for multiple cards]
- 6) run the net startup bits for your new eth?? interface manually
- (usually /etc/rc.inet[12] at boot time).
- 7) enjoy!
-
- Note that autoprobing is not allowed in loadable modules - the system is
- already up and running and you're messing with interrupts.
-
- To unload a module, turn off the associated interface
- 'ifconfig eth?? down' then 'rmmod ewrk3'.
-
- Promiscuous mode has been turned off in this driver, but all the
- multicast address bits have been turned on. This improved the send
- performance on a busy network by about 13%.
-
- Ioctl's have now been provided (primarily because I wanted to grab some
- packet size statistics). They are patterned after 'plipconfig.c' from a
- suggestion by Alan Cox. Using these ioctls, you can enable promiscuous
- mode, add/delete multicast addresses, change the hardware address, get
- packet size distribution statistics and muck around with the control and
- status register. I'll add others if and when the need arises.
-
- TO DO:
- ------
-
-
- Revision History
- ----------------
-
- Version Date Description
-
- 0.1 26-aug-94 Initial writing. ALPHA code release.
- 0.11 31-aug-94 Fixed: 2k mode memory base calc.,
- LeMAC version calc.,
- IRQ vector assignments during autoprobe.
- 0.12 31-aug-94 Tested working on LeMAC2 (DE20[345]-AC) card.
- Fixed up MCA hash table algorithm.
- 0.20 4-sep-94 Added IOCTL functionality.
- 0.21 14-sep-94 Added I/O mode.
- 0.21axp 15-sep-94 Special version for ALPHA AXP Linux V1.0.
- 0.22 16-sep-94 Added more IOCTLs & tidied up.
- 0.23 21-sep-94 Added transmit cut through.
- 0.24 31-oct-94 Added uid checks in some ioctls.
- 0.30 1-nov-94 BETA code release.
- 0.31 5-dec-94 Added check/allocate region code.
- 0.32 16-jan-95 Broadcast packet fix.
- 0.33 10-Feb-95 Fix recognition bug reported by <bkm@star.rl.ac.uk>.
- 0.40 27-Dec-95 Rationalise MODULE and autoprobe code.
- Rewrite for portability & updated.
- ALPHA support from <jestabro@amt.tay1.dec.com>
- Added verify_area() calls in ewrk3_ioctl() from
- suggestion by <heiko@colossus.escape.de>.
- Add new multicasting code.
- 0.41 20-Jan-96 Fix IRQ set up problem reported by
- <kenneth@bbs.sas.ntu.ac.sg>.
- 0.42 22-Apr-96 Fix alloc_device() bug <jari@markkus2.fimr.fi>
- 0.43 16-Aug-96 Update alloc_device() to conform to de4x5.c
- 0.44 08-Nov-01 use library crc32 functions <Matt_Domsch@dell.com>
- 0.45 19-Jul-02 fix unaligned access on alpha <martin@bruli.net>
- 0.46 10-Oct-02 Multiple NIC support when module <akropel1@rochester.rr.com>
- 0.47 18-Oct-02 ethtool support <akropel1@rochester.rr.com>
- 0.48 18-Oct-02 cli/sti removal for 2.5 <vda@port.imtp.ilyichevsk.odessa.ua>
- ioctl locking, signature search cleanup <akropel1@rochester.rr.com>
-
- =========================================================================
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/string.h>
-#include <linux/errno.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/crc32.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/ethtool.h>
-#include <linux/time.h>
-#include <linux/types.h>
-#include <linux/unistd.h>
-#include <linux/ctype.h>
-#include <linux/bitops.h>
-
-#include <asm/io.h>
-#include <asm/dma.h>
-#include <asm/uaccess.h>
-
-#include "ewrk3.h"
-
-#define DRV_NAME "ewrk3"
-#define DRV_VERSION "0.48"
-
-static char version[] __initdata =
-DRV_NAME ":v" DRV_VERSION " 2002/10/18 davies@maniac.ultranet.com\n";
-
-#ifdef EWRK3_DEBUG
-static int ewrk3_debug = EWRK3_DEBUG;
-#else
-static int ewrk3_debug = 1;
-#endif
-
-#define EWRK3_NDA 0xffe0 /* No Device Address */
-
-#define PROBE_LENGTH 32
-#define ETH_PROM_SIG 0xAA5500FFUL
-
-#ifndef EWRK3_SIGNATURE
-#define EWRK3_SIGNATURE {"DE203","DE204","DE205",""}
-#define EWRK3_STRLEN 8
-#endif
-
-#ifndef EWRK3_RAM_BASE_ADDRESSES
-#define EWRK3_RAM_BASE_ADDRESSES {0xc0000,0xd0000,0x00000}
-#endif
-
-/*
- ** Sets up the I/O area for the autoprobe.
- */
-#define EWRK3_IO_BASE 0x100 /* Start address for probe search */
-#define EWRK3_IOP_INC 0x20 /* I/O address increment */
-#define EWRK3_TOTAL_SIZE 0x20 /* required I/O address length */
-
-#ifndef MAX_NUM_EWRK3S
-#define MAX_NUM_EWRK3S 21
-#endif
-
-#ifndef EWRK3_EISA_IO_PORTS
-#define EWRK3_EISA_IO_PORTS 0x0c00 /* I/O port base address, slot 0 */
-#endif
-
-#ifndef MAX_EISA_SLOTS
-#define MAX_EISA_SLOTS 16
-#define EISA_SLOT_INC 0x1000
-#endif
-
-#define QUEUE_PKT_TIMEOUT (1*HZ) /* Jiffies */
-
-/*
- ** EtherWORKS 3 shared memory window sizes
- */
-#define IO_ONLY 0x00
-#define SHMEM_2K 0x800
-#define SHMEM_32K 0x8000
-#define SHMEM_64K 0x10000
-
-/*
- ** EtherWORKS 3 IRQ ENABLE/DISABLE
- */
-#define ENABLE_IRQs { \
- icr |= lp->irq_mask;\
- outb(icr, EWRK3_ICR); /* Enable the IRQs */\
-}
-
-#define DISABLE_IRQs { \
- icr = inb(EWRK3_ICR);\
- icr &= ~lp->irq_mask;\
- outb(icr, EWRK3_ICR); /* Disable the IRQs */\
-}
-
-/*
- ** EtherWORKS 3 START/STOP
- */
-#define START_EWRK3 { \
- csr = inb(EWRK3_CSR);\
- csr &= ~(CSR_TXD|CSR_RXD);\
- outb(csr, EWRK3_CSR); /* Enable the TX and/or RX */\
-}
-
-#define STOP_EWRK3 { \
- csr = (CSR_TXD|CSR_RXD);\
- outb(csr, EWRK3_CSR); /* Disable the TX and/or RX */\
-}
-
-/*
- ** The EtherWORKS 3 private structure
- */
-#define EWRK3_PKT_STAT_SZ 16
-#define EWRK3_PKT_BIN_SZ 128 /* Should be >=100 unless you
- increase EWRK3_PKT_STAT_SZ */
-
-struct ewrk3_stats {
- u32 bins[EWRK3_PKT_STAT_SZ];
- u32 unicast;
- u32 multicast;
- u32 broadcast;
- u32 excessive_collisions;
- u32 tx_underruns;
- u32 excessive_underruns;
-};
-
-struct ewrk3_private {
- char adapter_name[80]; /* Name exported to /proc/ioports */
- u_long shmem_base; /* Shared memory start address */
- void __iomem *shmem;
- u_long shmem_length; /* Shared memory window length */
- struct ewrk3_stats pktStats; /* Private stats counters */
- u_char irq_mask; /* Adapter IRQ mask bits */
- u_char mPage; /* Maximum 2kB Page number */
- u_char lemac; /* Chip rev. level */
- u_char hard_strapped; /* Don't allow a full open */
- u_char txc; /* Transmit cut through */
- void __iomem *mctbl; /* Pointer to the multicast table */
- u_char led_mask; /* Used to reserve LED access for ethtool */
- spinlock_t hw_lock;
-};
-
-/*
- ** Force the EtherWORKS 3 card to be in 2kB MODE
- */
-#define FORCE_2K_MODE { \
- shmem_length = SHMEM_2K;\
- outb(((mem_start - 0x80000) >> 11), EWRK3_MBR);\
-}
-
-/*
- ** Public Functions
- */
-static int ewrk3_open(struct net_device *dev);
-static netdev_tx_t ewrk3_queue_pkt(struct sk_buff *skb, struct net_device *dev);
-static irqreturn_t ewrk3_interrupt(int irq, void *dev_id);
-static int ewrk3_close(struct net_device *dev);
-static void set_multicast_list(struct net_device *dev);
-static int ewrk3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
-static const struct ethtool_ops ethtool_ops_203;
-static const struct ethtool_ops ethtool_ops;
-
-/*
- ** Private functions
- */
-static int ewrk3_hw_init(struct net_device *dev, u_long iobase);
-static void ewrk3_init(struct net_device *dev);
-static int ewrk3_rx(struct net_device *dev);
-static int ewrk3_tx(struct net_device *dev);
-static void ewrk3_timeout(struct net_device *dev);
-
-static void EthwrkSignature(char *name, char *eeprom_image);
-static int DevicePresent(u_long iobase);
-static void SetMulticastFilter(struct net_device *dev);
-static int EISA_signature(char *name, s32 eisa_id);
-
-static int Read_EEPROM(u_long iobase, u_char eaddr);
-static int Write_EEPROM(short data, u_long iobase, u_char eaddr);
-static u_char get_hw_addr(struct net_device *dev, u_char * eeprom_image, char chipType);
-
-static int ewrk3_probe1(struct net_device *dev, u_long iobase, int irq);
-static int isa_probe(struct net_device *dev, u_long iobase);
-static int eisa_probe(struct net_device *dev, u_long iobase);
-
-static u_char irq[MAX_NUM_EWRK3S+1] = {5, 0, 10, 3, 11, 9, 15, 12};
-
-static char name[EWRK3_STRLEN + 1];
-static int num_ewrks3s;
-
-/*
- ** Miscellaneous defines...
- */
-#define INIT_EWRK3 {\
- outb(EEPROM_INIT, EWRK3_IOPR);\
- mdelay(1);\
-}
-
-#ifndef MODULE
-struct net_device * __init ewrk3_probe(int unit)
-{
- struct net_device *dev = alloc_etherdev(sizeof(struct ewrk3_private));
- int err;
-
- if (!dev)
- return ERR_PTR(-ENOMEM);
-
- if (unit >= 0) {
- sprintf(dev->name, "eth%d", unit);
- netdev_boot_setup_check(dev);
- }
-
- err = ewrk3_probe1(dev, dev->base_addr, dev->irq);
- if (err)
- goto out;
- return dev;
-out:
- free_netdev(dev);
- return ERR_PTR(err);
-
-}
-#endif
-
-static int __init ewrk3_probe1(struct net_device *dev, u_long iobase, int irq)
-{
- int err;
-
- dev->base_addr = iobase;
- dev->irq = irq;
-
- /* Address PROM pattern */
- err = isa_probe(dev, iobase);
- if (err != 0)
- err = eisa_probe(dev, iobase);
-
- if (err)
- return err;
-
- err = register_netdev(dev);
- if (err)
- release_region(dev->base_addr, EWRK3_TOTAL_SIZE);
-
- return err;
-}
-
-static const struct net_device_ops ewrk3_netdev_ops = {
- .ndo_open = ewrk3_open,
- .ndo_start_xmit = ewrk3_queue_pkt,
- .ndo_stop = ewrk3_close,
- .ndo_set_rx_mode = set_multicast_list,
- .ndo_do_ioctl = ewrk3_ioctl,
- .ndo_tx_timeout = ewrk3_timeout,
- .ndo_change_mtu = eth_change_mtu,
- .ndo_set_mac_address = eth_mac_addr,
- .ndo_validate_addr = eth_validate_addr,
-};
-
-static int __init
-ewrk3_hw_init(struct net_device *dev, u_long iobase)
-{
- struct ewrk3_private *lp;
- int i, status = 0;
- u_long mem_start, shmem_length;
- u_char cr, cmr, icr, nicsr, lemac, hard_strapped = 0;
- u_char eeprom_image[EEPROM_MAX], chksum, eisa_cr = 0;
-
- /*
- ** Stop the EWRK3. Enable the DBR ROM. Disable interrupts and remote boot.
- ** This also disables the EISA_ENABLE bit in the EISA Control Register.
- */
- if (iobase > 0x400)
- eisa_cr = inb(EISA_CR);
- INIT_EWRK3;
-
- nicsr = inb(EWRK3_CSR);
-
- icr = inb(EWRK3_ICR);
- icr &= 0x70;
- outb(icr, EWRK3_ICR); /* Disable all the IRQs */
-
- if (nicsr != (CSR_TXD | CSR_RXD))
- return -ENXIO;
-
- /* Check that the EEPROM is alive and well and not living on Pluto... */
- for (chksum = 0, i = 0; i < EEPROM_MAX; i += 2) {
- union {
- short val;
- char c[2];
- } tmp;
-
- tmp.val = (short) Read_EEPROM(iobase, (i >> 1));
- eeprom_image[i] = tmp.c[0];
- eeprom_image[i + 1] = tmp.c[1];
- chksum += eeprom_image[i] + eeprom_image[i + 1];
- }
-
- if (chksum != 0) { /* Bad EEPROM Data! */
- printk("%s: Device has a bad on-board EEPROM.\n", dev->name);
- return -ENXIO;
- }
-
- EthwrkSignature(name, eeprom_image);
- if (*name == '\0')
- return -ENXIO;
-
- dev->base_addr = iobase;
-
- if (iobase > 0x400) {
- outb(eisa_cr, EISA_CR); /* Rewrite the EISA CR */
- }
- lemac = eeprom_image[EEPROM_CHIPVER];
- cmr = inb(EWRK3_CMR);
-
- if (((lemac == LeMAC) && ((cmr & CMR_NO_EEPROM) != CMR_NO_EEPROM)) ||
- ((lemac == LeMAC2) && !(cmr & CMR_HS))) {
- printk("%s: %s at %#4lx", dev->name, name, iobase);
- hard_strapped = 1;
- } else if ((iobase & 0x0fff) == EWRK3_EISA_IO_PORTS) {
- /* EISA slot address */
- printk("%s: %s at %#4lx (EISA slot %ld)",
- dev->name, name, iobase, ((iobase >> 12) & 0x0f));
- } else { /* ISA port address */
- printk("%s: %s at %#4lx", dev->name, name, iobase);
- }
-
- printk(", h/w address ");
- if (lemac != LeMAC2)
- DevicePresent(iobase); /* need after EWRK3_INIT */
- status = get_hw_addr(dev, eeprom_image, lemac);
- printk("%pM\n", dev->dev_addr);
-
- if (status) {
- printk(" which has an EEPROM CRC error.\n");
- return -ENXIO;
- }
-
- if (lemac == LeMAC2) { /* Special LeMAC2 CMR things */
- cmr &= ~(CMR_RA | CMR_WB | CMR_LINK | CMR_POLARITY | CMR_0WS);
- if (eeprom_image[EEPROM_MISC0] & READ_AHEAD)
- cmr |= CMR_RA;
- if (eeprom_image[EEPROM_MISC0] & WRITE_BEHIND)
- cmr |= CMR_WB;
- if (eeprom_image[EEPROM_NETMAN0] & NETMAN_POL)
- cmr |= CMR_POLARITY;
- if (eeprom_image[EEPROM_NETMAN0] & NETMAN_LINK)
- cmr |= CMR_LINK;
- if (eeprom_image[EEPROM_MISC0] & _0WS_ENA)
- cmr |= CMR_0WS;
- }
- if (eeprom_image[EEPROM_SETUP] & SETUP_DRAM)
- cmr |= CMR_DRAM;
- outb(cmr, EWRK3_CMR);
-
- cr = inb(EWRK3_CR); /* Set up the Control Register */
- cr |= eeprom_image[EEPROM_SETUP] & SETUP_APD;
- if (cr & SETUP_APD)
- cr |= eeprom_image[EEPROM_SETUP] & SETUP_PS;
- cr |= eeprom_image[EEPROM_MISC0] & FAST_BUS;
- cr |= eeprom_image[EEPROM_MISC0] & ENA_16;
- outb(cr, EWRK3_CR);
-
- /*
- ** Determine the base address and window length for the EWRK3
- ** RAM from the memory base register.
- */
- mem_start = inb(EWRK3_MBR);
- shmem_length = 0;
- if (mem_start != 0) {
- if ((mem_start >= 0x0a) && (mem_start <= 0x0f)) {
- mem_start *= SHMEM_64K;
- shmem_length = SHMEM_64K;
- } else if ((mem_start >= 0x14) && (mem_start <= 0x1f)) {
- mem_start *= SHMEM_32K;
- shmem_length = SHMEM_32K;
- } else if ((mem_start >= 0x40) && (mem_start <= 0xff)) {
- mem_start = mem_start * SHMEM_2K + 0x80000;
- shmem_length = SHMEM_2K;
- } else {
- return -ENXIO;
- }
- }
- /*
- ** See the top of this source code for comments about
- ** uncommenting this line.
- */
-/* FORCE_2K_MODE; */
-
- if (hard_strapped) {
- printk(" is hard strapped.\n");
- } else if (mem_start) {
- printk(" has a %dk RAM window", (int) (shmem_length >> 10));
- printk(" at 0x%.5lx", mem_start);
- } else {
- printk(" is in I/O only mode");
- }
-
- lp = netdev_priv(dev);
- lp->shmem_base = mem_start;
- lp->shmem = ioremap(mem_start, shmem_length);
- if (!lp->shmem)
- return -ENOMEM;
- lp->shmem_length = shmem_length;
- lp->lemac = lemac;
- lp->hard_strapped = hard_strapped;
- lp->led_mask = CR_LED;
- spin_lock_init(&lp->hw_lock);
-
- lp->mPage = 64;
- if (cmr & CMR_DRAM)
- lp->mPage <<= 1; /* 2 DRAMS on module */
-
- sprintf(lp->adapter_name, "%s (%s)", name, dev->name);
-
- lp->irq_mask = ICR_TNEM | ICR_TXDM | ICR_RNEM | ICR_RXDM;
-
- if (!hard_strapped) {
- /*
- ** Enable EWRK3 board interrupts for autoprobing
- */
- icr |= ICR_IE; /* Enable interrupts */
- outb(icr, EWRK3_ICR);
-
- /* The DMA channel may be passed in on this parameter. */
- dev->dma = 0;
-
- /* To auto-IRQ we enable the initialization-done and DMA err,
- interrupts. For now we will always get a DMA error. */
- if (dev->irq < 2) {
-#ifndef MODULE
- u_char irqnum;
- unsigned long irq_mask;
-
-
- irq_mask = probe_irq_on();
-
- /*
- ** Trigger a TNE interrupt.
- */
- icr |= ICR_TNEM;
- outb(1, EWRK3_TDQ); /* Write to the TX done queue */
- outb(icr, EWRK3_ICR); /* Unmask the TXD interrupt */
-
- irqnum = irq[((icr & IRQ_SEL) >> 4)];
-
- mdelay(20);
- dev->irq = probe_irq_off(irq_mask);
- if ((dev->irq) && (irqnum == dev->irq)) {
- printk(" and uses IRQ%d.\n", dev->irq);
- } else {
- if (!dev->irq) {
- printk(" and failed to detect IRQ line.\n");
- } else if ((irqnum == 1) && (lemac == LeMAC2)) {
- printk(" and an illegal IRQ line detected.\n");
- } else {
- printk(", but incorrect IRQ line detected.\n");
- }
- iounmap(lp->shmem);
- return -ENXIO;
- }
-
- DISABLE_IRQs; /* Mask all interrupts */
-
-#endif /* MODULE */
- } else {
- printk(" and requires IRQ%d.\n", dev->irq);
- }
- }
-
- if (ewrk3_debug > 1) {
- printk(version);
- }
- /* The EWRK3-specific entries in the device structure. */
- dev->netdev_ops = &ewrk3_netdev_ops;
- if (lp->adapter_name[4] == '3')
- SET_ETHTOOL_OPS(dev, ðtool_ops_203);
- else
- SET_ETHTOOL_OPS(dev, ðtool_ops);
- dev->watchdog_timeo = QUEUE_PKT_TIMEOUT;
-
- dev->mem_start = 0;
-
- return 0;
-}
-
-
-static int ewrk3_open(struct net_device *dev)
-{
- struct ewrk3_private *lp = netdev_priv(dev);
- u_long iobase = dev->base_addr;
- int status = 0;
- u_char icr, csr;
-
- /*
- ** Stop the TX and RX...
- */
- STOP_EWRK3;
-
- if (!lp->hard_strapped) {
- if (request_irq(dev->irq, (void *) ewrk3_interrupt, 0, "ewrk3", dev)) {
- printk("ewrk3_open(): Requested IRQ%d is busy\n", dev->irq);
- status = -EAGAIN;
- } else {
-
- /*
- ** Re-initialize the EWRK3...
- */
- ewrk3_init(dev);
-
- if (ewrk3_debug > 1) {
- printk("%s: ewrk3 open with irq %d\n", dev->name, dev->irq);
- printk(" physical address: %pM\n", dev->dev_addr);
- if (lp->shmem_length == 0) {
- printk(" no shared memory, I/O only mode\n");
- } else {
- printk(" start of shared memory: 0x%08lx\n", lp->shmem_base);
- printk(" window length: 0x%04lx\n", lp->shmem_length);
- }
- printk(" # of DRAMS: %d\n", ((inb(EWRK3_CMR) & 0x02) ? 2 : 1));
- printk(" csr: 0x%02x\n", inb(EWRK3_CSR));
- printk(" cr: 0x%02x\n", inb(EWRK3_CR));
- printk(" icr: 0x%02x\n", inb(EWRK3_ICR));
- printk(" cmr: 0x%02x\n", inb(EWRK3_CMR));
- printk(" fmqc: 0x%02x\n", inb(EWRK3_FMQC));
- }
- netif_start_queue(dev);
- /*
- ** Unmask EWRK3 board interrupts
- */
- icr = inb(EWRK3_ICR);
- ENABLE_IRQs;
-
- }
- } else {
- printk(KERN_ERR "%s: ewrk3 available for hard strapped set up only.\n", dev->name);
- printk(KERN_ERR " Run the 'ewrk3setup' utility or remove the hard straps.\n");
- return -EINVAL;
- }
-
- return status;
-}
-
-/*
- ** Initialize the EtherWORKS 3 operating conditions
- */
-static void ewrk3_init(struct net_device *dev)
-{
- struct ewrk3_private *lp = netdev_priv(dev);
- u_char csr, page;
- u_long iobase = dev->base_addr;
- int i;
-
- /*
- ** Enable any multicasts
- */
- set_multicast_list(dev);
-
- /*
- ** Set hardware MAC address. Address is initialized from the EEPROM
- ** during startup but may have since been changed by the user.
- */
- for (i=0; i<ETH_ALEN; i++)
- outb(dev->dev_addr[i], EWRK3_PAR0 + i);
-
- /*
- ** Clean out any remaining entries in all the queues here
- */
- while (inb(EWRK3_TQ));
- while (inb(EWRK3_TDQ));
- while (inb(EWRK3_RQ));
- while (inb(EWRK3_FMQ));
-
- /*
- ** Write a clean free memory queue
- */
- for (page = 1; page < lp->mPage; page++) { /* Write the free page numbers */
- outb(page, EWRK3_FMQ); /* to the Free Memory Queue */
- }
-
- START_EWRK3; /* Enable the TX and/or RX */
-}
-
-/*
- * Transmit timeout
- */
-
-static void ewrk3_timeout(struct net_device *dev)
-{
- struct ewrk3_private *lp = netdev_priv(dev);
- u_char icr, csr;
- u_long iobase = dev->base_addr;
-
- if (!lp->hard_strapped)
- {
- printk(KERN_WARNING"%s: transmit timed/locked out, status %04x, resetting.\n",
- dev->name, inb(EWRK3_CSR));
-
- /*
- ** Mask all board interrupts
- */
- DISABLE_IRQs;
-
- /*
- ** Stop the TX and RX...
- */
- STOP_EWRK3;
-
- ewrk3_init(dev);
-
- /*
- ** Unmask EWRK3 board interrupts
- */
- ENABLE_IRQs;
-
- dev->trans_start = jiffies; /* prevent tx timeout */
- netif_wake_queue(dev);
- }
-}
-
-/*
- ** Writes a socket buffer to the free page queue
- */
-static netdev_tx_t ewrk3_queue_pkt(struct sk_buff *skb, struct net_device *dev)
-{
- struct ewrk3_private *lp = netdev_priv(dev);
- u_long iobase = dev->base_addr;
- void __iomem *buf = NULL;
- u_char icr;
- u_char page;
-
- spin_lock_irq (&lp->hw_lock);
- DISABLE_IRQs;
-
- /* if no resources available, exit, request packet be queued */
- if (inb (EWRK3_FMQC) == 0) {
- printk (KERN_WARNING "%s: ewrk3_queue_pkt(): No free resources...\n",
- dev->name);
- printk (KERN_WARNING "%s: ewrk3_queue_pkt(): CSR: %02x ICR: %02x FMQC: %02x\n",
- dev->name, inb (EWRK3_CSR), inb (EWRK3_ICR),
- inb (EWRK3_FMQC));
- goto err_out;
- }
-
- /*
- ** Get a free page from the FMQ
- */
- if ((page = inb (EWRK3_FMQ)) >= lp->mPage) {
- printk ("ewrk3_queue_pkt(): Invalid free memory page (%d).\n",
- (u_char) page);
- goto err_out;
- }
-
-
- /*
- ** Set up shared memory window and pointer into the window
- */
- if (lp->shmem_length == IO_ONLY) {
- outb (page, EWRK3_IOPR);
- } else if (lp->shmem_length == SHMEM_2K) {
- buf = lp->shmem;
- outb (page, EWRK3_MPR);
- } else if (lp->shmem_length == SHMEM_32K) {
- buf = (((short) page << 11) & 0x7800) + lp->shmem;
- outb ((page >> 4), EWRK3_MPR);
- } else if (lp->shmem_length == SHMEM_64K) {
- buf = (((short) page << 11) & 0xf800) + lp->shmem;
- outb ((page >> 5), EWRK3_MPR);
- } else {
- printk (KERN_ERR "%s: Oops - your private data area is hosed!\n",
- dev->name);
- BUG ();
- }
-
- /*
- ** Set up the buffer control structures and copy the data from
- ** the socket buffer to the shared memory .
- */
- if (lp->shmem_length == IO_ONLY) {
- int i;
- u_char *p = skb->data;
- outb ((char) (TCR_QMODE | TCR_PAD | TCR_IFC), EWRK3_DATA);
- outb ((char) (skb->len & 0xff), EWRK3_DATA);
- outb ((char) ((skb->len >> 8) & 0xff), EWRK3_DATA);
- outb ((char) 0x04, EWRK3_DATA);
- for (i = 0; i < skb->len; i++) {
- outb (*p++, EWRK3_DATA);
- }
- outb (page, EWRK3_TQ); /* Start sending pkt */
- } else {
- writeb ((char) (TCR_QMODE | TCR_PAD | TCR_IFC), buf); /* ctrl byte */
- buf += 1;
- writeb ((char) (skb->len & 0xff), buf); /* length (16 bit xfer) */
- buf += 1;
- if (lp->txc) {
- writeb(((skb->len >> 8) & 0xff) | XCT, buf);
- buf += 1;
- writeb (0x04, buf); /* index byte */
- buf += 1;
- writeb (0x00, (buf + skb->len)); /* Write the XCT flag */
- memcpy_toio (buf, skb->data, PRELOAD); /* Write PRELOAD bytes */
- outb (page, EWRK3_TQ); /* Start sending pkt */
- memcpy_toio (buf + PRELOAD,
- skb->data + PRELOAD,
- skb->len - PRELOAD);
- writeb (0xff, (buf + skb->len)); /* Write the XCT flag */
- } else {
- writeb ((skb->len >> 8) & 0xff, buf);
- buf += 1;
- writeb (0x04, buf); /* index byte */
- buf += 1;
- memcpy_toio (buf, skb->data, skb->len); /* Write data bytes */
- outb (page, EWRK3_TQ); /* Start sending pkt */
- }
- }
-
- ENABLE_IRQs;
- spin_unlock_irq (&lp->hw_lock);
-
- dev->stats.tx_bytes += skb->len;
- dev_kfree_skb (skb);
-
- /* Check for free resources: stop Tx queue if there are none */
- if (inb (EWRK3_FMQC) == 0)
- netif_stop_queue (dev);
-
- return NETDEV_TX_OK;
-
-err_out:
- ENABLE_IRQs;
- spin_unlock_irq (&lp->hw_lock);
- return NETDEV_TX_BUSY;
-}
-
-/*
- ** The EWRK3 interrupt handler.
- */
-static irqreturn_t ewrk3_interrupt(int irq, void *dev_id)
-{
- struct net_device *dev = dev_id;
- struct ewrk3_private *lp;
- u_long iobase;
- u_char icr, cr, csr;
-
- lp = netdev_priv(dev);
- iobase = dev->base_addr;
-
- /* get the interrupt information */
- csr = inb(EWRK3_CSR);
-
- /*
- ** Mask the EWRK3 board interrupts and turn on the LED
- */
- spin_lock(&lp->hw_lock);
- DISABLE_IRQs;
-
- cr = inb(EWRK3_CR);
- cr |= lp->led_mask;
- outb(cr, EWRK3_CR);
-
- if (csr & CSR_RNE) /* Rx interrupt (packet[s] arrived) */
- ewrk3_rx(dev);
-
- if (csr & CSR_TNE) /* Tx interrupt (packet sent) */
- ewrk3_tx(dev);
-
- /*
- ** Now deal with the TX/RX disable flags. These are set when there
- ** are no more resources. If resources free up then enable these
- ** interrupts, otherwise mask them - failure to do this will result
- ** in the system hanging in an interrupt loop.
- */
- if (inb(EWRK3_FMQC)) { /* any resources available? */
- lp->irq_mask |= ICR_TXDM | ICR_RXDM; /* enable the interrupt source */
- csr &= ~(CSR_TXD | CSR_RXD); /* ensure restart of a stalled TX or RX */
- outb(csr, EWRK3_CSR);
- netif_wake_queue(dev);
- } else {
- lp->irq_mask &= ~(ICR_TXDM | ICR_RXDM); /* disable the interrupt source */
- }
-
- /* Unmask the EWRK3 board interrupts and turn off the LED */
- cr &= ~(lp->led_mask);
- outb(cr, EWRK3_CR);
- ENABLE_IRQs;
- spin_unlock(&lp->hw_lock);
- return IRQ_HANDLED;
-}
-
-/* Called with lp->hw_lock held */
-static int ewrk3_rx(struct net_device *dev)
-{
- struct ewrk3_private *lp = netdev_priv(dev);
- u_long iobase = dev->base_addr;
- int i, status = 0;
- u_char page;
- void __iomem *buf = NULL;
-
- while (inb(EWRK3_RQC) && !status) { /* Whilst there's incoming data */
- if ((page = inb(EWRK3_RQ)) < lp->mPage) { /* Get next entry's buffer page */
- /*
- ** Set up shared memory window and pointer into the window
- */
- if (lp->shmem_length == IO_ONLY) {
- outb(page, EWRK3_IOPR);
- } else if (lp->shmem_length == SHMEM_2K) {
- buf = lp->shmem;
- outb(page, EWRK3_MPR);
- } else if (lp->shmem_length == SHMEM_32K) {
- buf = (((short) page << 11) & 0x7800) + lp->shmem;
- outb((page >> 4), EWRK3_MPR);
- } else if (lp->shmem_length == SHMEM_64K) {
- buf = (((short) page << 11) & 0xf800) + lp->shmem;
- outb((page >> 5), EWRK3_MPR);
- } else {
- status = -1;
- printk("%s: Oops - your private data area is hosed!\n", dev->name);
- }
-
- if (!status) {
- char rx_status;
- int pkt_len;
-
- if (lp->shmem_length == IO_ONLY) {
- rx_status = inb(EWRK3_DATA);
- pkt_len = inb(EWRK3_DATA);
- pkt_len |= ((u_short) inb(EWRK3_DATA) << 8);
- } else {
- rx_status = readb(buf);
- buf += 1;
- pkt_len = readw(buf);
- buf += 3;
- }
-
- if (!(rx_status & R_ROK)) { /* There was an error. */
- dev->stats.rx_errors++; /* Update the error stats. */
- if (rx_status & R_DBE)
- dev->stats.rx_frame_errors++;
- if (rx_status & R_CRC)
- dev->stats.rx_crc_errors++;
- if (rx_status & R_PLL)
- dev->stats.rx_fifo_errors++;
- } else {
- struct sk_buff *skb;
- skb = netdev_alloc_skb(dev,
- pkt_len + 2);
-
- if (skb != NULL) {
- unsigned char *p;
- skb_reserve(skb, 2); /* Align to 16 bytes */
- p = skb_put(skb, pkt_len);
-
- if (lp->shmem_length == IO_ONLY) {
- *p = inb(EWRK3_DATA); /* dummy read */
- for (i = 0; i < pkt_len; i++) {
- *p++ = inb(EWRK3_DATA);
- }
- } else {
- memcpy_fromio(p, buf, pkt_len);
- }
-
- for (i = 1; i < EWRK3_PKT_STAT_SZ - 1; i++) {
- if (pkt_len < i * EWRK3_PKT_BIN_SZ) {
- lp->pktStats.bins[i]++;
- i = EWRK3_PKT_STAT_SZ;
- }
- }
- p = skb->data; /* Look at the dest addr */
- if (is_multicast_ether_addr(p)) {
- if (is_broadcast_ether_addr(p)) {
- lp->pktStats.broadcast++;
- } else {
- lp->pktStats.multicast++;
- }
- } else if (ether_addr_equal(p,
- dev->dev_addr)) {
- lp->pktStats.unicast++;
- }
- lp->pktStats.bins[0]++; /* Duplicates stats.rx_packets */
- if (lp->pktStats.bins[0] == 0) { /* Reset counters */
- memset(&lp->pktStats, 0, sizeof(lp->pktStats));
- }
- /*
- ** Notify the upper protocol layers that there is another
- ** packet to handle
- */
- skb->protocol = eth_type_trans(skb, dev);
- netif_rx(skb);
-
- /*
- ** Update stats
- */
- dev->stats.rx_packets++;
- dev->stats.rx_bytes += pkt_len;
- } else {
- printk("%s: Insufficient memory; nuking packet.\n", dev->name);
- dev->stats.rx_dropped++; /* Really, deferred. */
- break;
- }
- }
- }
- /*
- ** Return the received buffer to the free memory queue
- */
- outb(page, EWRK3_FMQ);
- } else {
- printk("ewrk3_rx(): Illegal page number, page %d\n", page);
- printk("ewrk3_rx(): CSR: %02x ICR: %02x FMQC: %02x\n", inb(EWRK3_CSR), inb(EWRK3_ICR), inb(EWRK3_FMQC));
- }
- }
- return status;
-}
-
-/*
-** Buffer sent - check for TX buffer errors.
-** Called with lp->hw_lock held
-*/
-static int ewrk3_tx(struct net_device *dev)
-{
- struct ewrk3_private *lp = netdev_priv(dev);
- u_long iobase = dev->base_addr;
- u_char tx_status;
-
- while ((tx_status = inb(EWRK3_TDQ)) > 0) { /* Whilst there's old buffers */
- if (tx_status & T_VSTS) { /* The status is valid */
- if (tx_status & T_TXE) {
- dev->stats.tx_errors++;
- if (tx_status & T_NCL)
- dev->stats.tx_carrier_errors++;
- if (tx_status & T_LCL)
- dev->stats.tx_window_errors++;
- if (tx_status & T_CTU) {
- if ((tx_status & T_COLL) ^ T_XUR) {
- lp->pktStats.tx_underruns++;
- } else {
- lp->pktStats.excessive_underruns++;
- }
- } else if (tx_status & T_COLL) {
- if ((tx_status & T_COLL) ^ T_XCOLL) {
- dev->stats.collisions++;
- } else {
- lp->pktStats.excessive_collisions++;
- }
- }
- } else {
- dev->stats.tx_packets++;
- }
- }
- }
-
- return 0;
-}
-
-static int ewrk3_close(struct net_device *dev)
-{
- struct ewrk3_private *lp = netdev_priv(dev);
- u_long iobase = dev->base_addr;
- u_char icr, csr;
-
- netif_stop_queue(dev);
-
- if (ewrk3_debug > 1) {
- printk("%s: Shutting down ethercard, status was %2.2x.\n",
- dev->name, inb(EWRK3_CSR));
- }
- /*
- ** We stop the EWRK3 here... mask interrupts and stop TX & RX
- */
- DISABLE_IRQs;
-
- STOP_EWRK3;
-
- /*
- ** Clean out the TX and RX queues here (note that one entry
- ** may get added to either the TXD or RX queues if the TX or RX
- ** just starts processing a packet before the STOP_EWRK3 command
- ** is received. This will be flushed in the ewrk3_open() call).
- */
- while (inb(EWRK3_TQ));
- while (inb(EWRK3_TDQ));
- while (inb(EWRK3_RQ));
-
- if (!lp->hard_strapped) {
- free_irq(dev->irq, dev);
- }
- return 0;
-}
-
-/*
- ** Set or clear the multicast filter for this adapter.
- */
-static void set_multicast_list(struct net_device *dev)
-{
- struct ewrk3_private *lp = netdev_priv(dev);
- u_long iobase = dev->base_addr;
- u_char csr;
-
- csr = inb(EWRK3_CSR);
-
- if (lp->shmem_length == IO_ONLY) {
- lp->mctbl = NULL;
- } else {
- lp->mctbl = lp->shmem + PAGE0_HTE;
- }
-
- csr &= ~(CSR_PME | CSR_MCE);
- if (dev->flags & IFF_PROMISC) { /* set promiscuous mode */
- csr |= CSR_PME;
- outb(csr, EWRK3_CSR);
- } else {
- SetMulticastFilter(dev);
- csr |= CSR_MCE;
- outb(csr, EWRK3_CSR);
- }
-}
-
-/*
- ** Calculate the hash code and update the logical address filter
- ** from a list of ethernet multicast addresses.
- ** Little endian crc one liner from Matt Thomas, DEC.
- **
- ** Note that when clearing the table, the broadcast bit must remain asserted
- ** to receive broadcast messages.
- */
-static void SetMulticastFilter(struct net_device *dev)
-{
- struct ewrk3_private *lp = netdev_priv(dev);
- struct netdev_hw_addr *ha;
- u_long iobase = dev->base_addr;
- int i;
- char bit, byte;
- short __iomem *p = lp->mctbl;
- u16 hashcode;
- u32 crc;
-
- spin_lock_irq(&lp->hw_lock);
-
- if (lp->shmem_length == IO_ONLY) {
- outb(0, EWRK3_IOPR);
- outw(PAGE0_HTE, EWRK3_PIR1);
- } else {
- outb(0, EWRK3_MPR);
- }
-
- if (dev->flags & IFF_ALLMULTI) {
- for (i = 0; i < (HASH_TABLE_LEN >> 3); i++) {
- if (lp->shmem_length == IO_ONLY) {
- outb(0xff, EWRK3_DATA);
- } else { /* memset didn't work here */
- writew(0xffff, p);
- p++;
- i++;
- }
- }
- } else {
- /* Clear table except for broadcast bit */
- if (lp->shmem_length == IO_ONLY) {
- for (i = 0; i < (HASH_TABLE_LEN >> 4) - 1; i++) {
- outb(0x00, EWRK3_DATA);
- }
- outb(0x80, EWRK3_DATA);
- i++; /* insert the broadcast bit */
- for (; i < (HASH_TABLE_LEN >> 3); i++) {
- outb(0x00, EWRK3_DATA);
- }
- } else {
- memset_io(lp->mctbl, 0, HASH_TABLE_LEN >> 3);
- writeb(0x80, lp->mctbl + (HASH_TABLE_LEN >> 4) - 1);
- }
-
- /* Update table */
- netdev_for_each_mc_addr(ha, dev) {
- crc = ether_crc_le(ETH_ALEN, ha->addr);
- hashcode = crc & ((1 << 9) - 1); /* hashcode is 9 LSb of CRC */
-
- byte = hashcode >> 3; /* bit[3-8] -> byte in filter */
- bit = 1 << (hashcode & 0x07); /* bit[0-2] -> bit in byte */
-
- if (lp->shmem_length == IO_ONLY) {
- u_char tmp;
-
- outw(PAGE0_HTE + byte, EWRK3_PIR1);
- tmp = inb(EWRK3_DATA);
- tmp |= bit;
- outw(PAGE0_HTE + byte, EWRK3_PIR1);
- outb(tmp, EWRK3_DATA);
- } else {
- writeb(readb(lp->mctbl + byte) | bit, lp->mctbl + byte);
- }
- }
- }
-
- spin_unlock_irq(&lp->hw_lock);
-}
-
-/*
- ** ISA bus I/O device probe
- */
-static int __init isa_probe(struct net_device *dev, u_long ioaddr)
-{
- int i = num_ewrks3s, maxSlots;
- int ret = -ENODEV;
-
- u_long iobase;
-
- if (ioaddr >= 0x400)
- goto out;
-
- if (ioaddr == 0) { /* Autoprobing */
- iobase = EWRK3_IO_BASE; /* Get the first slot address */
- maxSlots = 24;
- } else { /* Probe a specific location */
- iobase = ioaddr;
- maxSlots = i + 1;
- }
-
- for (; (i < maxSlots) && (dev != NULL);
- iobase += EWRK3_IOP_INC, i++)
- {
- if (request_region(iobase, EWRK3_TOTAL_SIZE, DRV_NAME)) {
- if (DevicePresent(iobase) == 0) {
- int irq = dev->irq;
- ret = ewrk3_hw_init(dev, iobase);
- if (!ret)
- break;
- dev->irq = irq;
- }
- release_region(iobase, EWRK3_TOTAL_SIZE);
- }
- }
- out:
-
- return ret;
-}
-
-/*
- ** EISA bus I/O device probe. Probe from slot 1 since slot 0 is usually
- ** the motherboard.
- */
-static int __init eisa_probe(struct net_device *dev, u_long ioaddr)
-{
- int i, maxSlots;
- u_long iobase;
- int ret = -ENODEV;
-
- if (ioaddr < 0x1000)
- goto out;
-
- iobase = ioaddr;
- i = (ioaddr >> 12);
- maxSlots = i + 1;
-
- for (i = 1; (i < maxSlots) && (dev != NULL); i++, iobase += EISA_SLOT_INC) {
- if (EISA_signature(name, EISA_ID) == 0) {
- if (request_region(iobase, EWRK3_TOTAL_SIZE, DRV_NAME) &&
- DevicePresent(iobase) == 0) {
- int irq = dev->irq;
- ret = ewrk3_hw_init(dev, iobase);
- if (!ret)
- break;
- dev->irq = irq;
- }
- release_region(iobase, EWRK3_TOTAL_SIZE);
- }
- }
-
- out:
- return ret;
-}
-
-
-/*
- ** Read the EWRK3 EEPROM using this routine
- */
-static int Read_EEPROM(u_long iobase, u_char eaddr)
-{
- int i;
-
- outb((eaddr & 0x3f), EWRK3_PIR1); /* set up 6 bits of address info */
- outb(EEPROM_RD, EWRK3_IOPR); /* issue read command */
- for (i = 0; i < 5000; i++)
- inb(EWRK3_CSR); /* wait 1msec */
-
- return inw(EWRK3_EPROM1); /* 16 bits data return */
-}
-
-/*
- ** Write the EWRK3 EEPROM using this routine
- */
-static int Write_EEPROM(short data, u_long iobase, u_char eaddr)
-{
- int i;
-
- outb(EEPROM_WR_EN, EWRK3_IOPR); /* issue write enable command */
- for (i = 0; i < 5000; i++)
- inb(EWRK3_CSR); /* wait 1msec */
- outw(data, EWRK3_EPROM1); /* write data to register */
- outb((eaddr & 0x3f), EWRK3_PIR1); /* set up 6 bits of address info */
- outb(EEPROM_WR, EWRK3_IOPR); /* issue write command */
- for (i = 0; i < 75000; i++)
- inb(EWRK3_CSR); /* wait 15msec */
- outb(EEPROM_WR_DIS, EWRK3_IOPR); /* issue write disable command */
- for (i = 0; i < 5000; i++)
- inb(EWRK3_CSR); /* wait 1msec */
-
- return 0;
-}
-
-/*
- ** Look for a particular board name in the on-board EEPROM.
- */
-static void __init EthwrkSignature(char *name, char *eeprom_image)
-{
- int i;
- char *signatures[] = EWRK3_SIGNATURE;
-
- for (i=0; *signatures[i] != '\0'; i++)
- if( !strncmp(eeprom_image+EEPROM_PNAME7, signatures[i], strlen(signatures[i])) )
- break;
-
- if (*signatures[i] != '\0') {
- memcpy(name, eeprom_image+EEPROM_PNAME7, EWRK3_STRLEN);
- name[EWRK3_STRLEN] = '\0';
- } else
- name[0] = '\0';
-}
-
-/*
- ** Look for a special sequence in the Ethernet station address PROM that
- ** is common across all EWRK3 products.
- **
- ** Search the Ethernet address ROM for the signature. Since the ROM address
- ** counter can start at an arbitrary point, the search must include the entire
- ** probe sequence length plus the (length_of_the_signature - 1).
- ** Stop the search IMMEDIATELY after the signature is found so that the
- ** PROM address counter is correctly positioned at the start of the
- ** ethernet address for later read out.
- */
-
-static int __init DevicePresent(u_long iobase)
-{
- union {
- struct {
- u32 a;
- u32 b;
- } llsig;
- char Sig[sizeof(u32) << 1];
- }
- dev;
- short sigLength;
- char data;
- int i, j, status = 0;
-
- dev.llsig.a = ETH_PROM_SIG;
- dev.llsig.b = ETH_PROM_SIG;
- sigLength = sizeof(u32) << 1;
-
- for (i = 0, j = 0; j < sigLength && i < PROBE_LENGTH + sigLength - 1; i++) {
- data = inb(EWRK3_APROM);
- if (dev.Sig[j] == data) { /* track signature */
- j++;
- } else { /* lost signature; begin search again */
- if (data == dev.Sig[0]) {
- j = 1;
- } else {
- j = 0;
- }
- }
- }
-
- if (j != sigLength) {
- status = -ENODEV; /* search failed */
- }
- return status;
-}
-
-static u_char __init get_hw_addr(struct net_device *dev, u_char * eeprom_image, char chipType)
-{
- int i, j, k;
- u_short chksum;
- u_char crc, lfsr, sd, status = 0;
- u_long iobase = dev->base_addr;
- u16 tmp;
-
- if (chipType == LeMAC2) {
- for (crc = 0x6a, j = 0; j < ETH_ALEN; j++) {
- sd = dev->dev_addr[j] = eeprom_image[EEPROM_PADDR0 + j];
- outb(dev->dev_addr[j], EWRK3_PAR0 + j);
- for (k = 0; k < 8; k++, sd >>= 1) {
- lfsr = ((((crc & 0x02) >> 1) ^ (crc & 0x01)) ^ (sd & 0x01)) << 7;
- crc = (crc >> 1) + lfsr;
- }
- }
- if (crc != eeprom_image[EEPROM_PA_CRC])
- status = -1;
- } else {
- for (i = 0, k = 0; i < ETH_ALEN;) {
- k <<= 1;
- if (k > 0xffff)
- k -= 0xffff;
-
- k += (u_char) (tmp = inb(EWRK3_APROM));
- dev->dev_addr[i] = (u_char) tmp;
- outb(dev->dev_addr[i], EWRK3_PAR0 + i);
- i++;
- k += (u_short) ((tmp = inb(EWRK3_APROM)) << 8);
- dev->dev_addr[i] = (u_char) tmp;
- outb(dev->dev_addr[i], EWRK3_PAR0 + i);
- i++;
-
- if (k > 0xffff)
- k -= 0xffff;
- }
- if (k == 0xffff)
- k = 0;
- chksum = inb(EWRK3_APROM);
- chksum |= (inb(EWRK3_APROM) << 8);
- if (k != chksum)
- status = -1;
- }
-
- return status;
-}
-
-/*
- ** Look for a particular board name in the EISA configuration space
- */
-static int __init EISA_signature(char *name, s32 eisa_id)
-{
- u_long i;
- char *signatures[] = EWRK3_SIGNATURE;
- char ManCode[EWRK3_STRLEN];
- union {
- s32 ID;
- char Id[4];
- } Eisa;
- int status = 0;
-
- *name = '\0';
- for (i = 0; i < 4; i++) {
- Eisa.Id[i] = inb(eisa_id + i);
- }
-
- ManCode[0] = (((Eisa.Id[0] >> 2) & 0x1f) + 0x40);
- ManCode[1] = (((Eisa.Id[1] & 0xe0) >> 5) + ((Eisa.Id[0] & 0x03) << 3) + 0x40);
- ManCode[2] = (((Eisa.Id[2] >> 4) & 0x0f) + 0x30);
- ManCode[3] = ((Eisa.Id[2] & 0x0f) + 0x30);
- ManCode[4] = (((Eisa.Id[3] >> 4) & 0x0f) + 0x30);
- ManCode[5] = '\0';
-
- for (i = 0; (*signatures[i] != '\0') && (*name == '\0'); i++) {
- if (strstr(ManCode, signatures[i]) != NULL) {
- strcpy(name, ManCode);
- status = 1;
- }
- }
-
- return status; /* return the device name string */
-}
-
-static void ewrk3_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info)
-{
- int fwrev = Read_EEPROM(dev->base_addr, EEPROM_REVLVL);
-
- strlcpy(info->driver, DRV_NAME, sizeof(info->driver));
- strlcpy(info->version, DRV_VERSION, sizeof(info->version));
- snprintf(info->fw_version, sizeof(info->fw_version), "%d", fwrev);
- strlcpy(info->bus_info, "N/A", sizeof(info->bus_info));
- info->eedump_len = EEPROM_MAX;
-}
-
-static int ewrk3_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
-{
- struct ewrk3_private *lp = netdev_priv(dev);
- unsigned long iobase = dev->base_addr;
- u8 cr = inb(EWRK3_CR);
-
- switch (lp->adapter_name[4]) {
- case '3': /* DE203 */
- ecmd->supported = SUPPORTED_BNC;
- ecmd->port = PORT_BNC;
- break;
-
- case '4': /* DE204 */
- ecmd->supported = SUPPORTED_TP;
- ecmd->port = PORT_TP;
- break;
-
- case '5': /* DE205 */
- ecmd->supported = SUPPORTED_TP | SUPPORTED_BNC | SUPPORTED_AUI;
- ecmd->autoneg = !(cr & CR_APD);
- /*
- ** Port is only valid if autoneg is disabled
- ** and even then we don't know if AUI is jumpered.
- */
- if (!ecmd->autoneg)
- ecmd->port = (cr & CR_PSEL) ? PORT_BNC : PORT_TP;
- break;
- }
-
- ecmd->supported |= SUPPORTED_10baseT_Half;
- ethtool_cmd_speed_set(ecmd, SPEED_10);
- ecmd->duplex = DUPLEX_HALF;
- return 0;
-}
-
-static int ewrk3_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
-{
- struct ewrk3_private *lp = netdev_priv(dev);
- unsigned long iobase = dev->base_addr;
- unsigned long flags;
- u8 cr;
-
- /* DE205 is the only card with anything to set */
- if (lp->adapter_name[4] != '5')
- return -EOPNOTSUPP;
-
- /* Sanity-check parameters */
- if (ecmd->speed != SPEED_10)
- return -EINVAL;
- if (ecmd->port != PORT_TP && ecmd->port != PORT_BNC)
- return -EINVAL; /* AUI is not software-selectable */
- if (ecmd->transceiver != XCVR_INTERNAL)
- return -EINVAL;
- if (ecmd->duplex != DUPLEX_HALF)
- return -EINVAL;
- if (ecmd->phy_address != 0)
- return -EINVAL;
-
- spin_lock_irqsave(&lp->hw_lock, flags);
- cr = inb(EWRK3_CR);
-
- /* If Autoneg is set, change to Auto Port mode */
- /* Otherwise, disable Auto Port and set port explicitly */
- if (ecmd->autoneg) {
- cr &= ~CR_APD;
- } else {
- cr |= CR_APD;
- if (ecmd->port == PORT_TP)
- cr &= ~CR_PSEL; /* Force TP */
- else
- cr |= CR_PSEL; /* Force BNC */
- }
-
- /* Commit the changes */
- outb(cr, EWRK3_CR);
- spin_unlock_irqrestore(&lp->hw_lock, flags);
- return 0;
-}
-
-static u32 ewrk3_get_link(struct net_device *dev)
-{
- unsigned long iobase = dev->base_addr;
- u8 cmr = inb(EWRK3_CMR);
- /* DE203 has BNC only and link status does not apply */
- /* On DE204 this is always valid since TP is the only port. */
- /* On DE205 this reflects TP status even if BNC or AUI is selected. */
- return !(cmr & CMR_LINK);
-}
-
-static int ewrk3_set_phys_id(struct net_device *dev,
- enum ethtool_phys_id_state state)
-{
- struct ewrk3_private *lp = netdev_priv(dev);
- unsigned long iobase = dev->base_addr;
- u8 cr;
-
- spin_lock_irq(&lp->hw_lock);
-
- switch (state) {
- case ETHTOOL_ID_ACTIVE:
- /* Prevent ISR from twiddling the LED */
- lp->led_mask = 0;
- spin_unlock_irq(&lp->hw_lock);
- return 2; /* cycle on/off twice per second */
-
- case ETHTOOL_ID_ON:
- cr = inb(EWRK3_CR);
- outb(cr | CR_LED, EWRK3_CR);
- break;
-
- case ETHTOOL_ID_OFF:
- cr = inb(EWRK3_CR);
- outb(cr & ~CR_LED, EWRK3_CR);
- break;
-
- case ETHTOOL_ID_INACTIVE:
- lp->led_mask = CR_LED;
- cr = inb(EWRK3_CR);
- outb(cr & ~CR_LED, EWRK3_CR);
- }
- spin_unlock_irq(&lp->hw_lock);
-
- return 0;
-}
-
-static const struct ethtool_ops ethtool_ops_203 = {
- .get_drvinfo = ewrk3_get_drvinfo,
- .get_settings = ewrk3_get_settings,
- .set_settings = ewrk3_set_settings,
- .set_phys_id = ewrk3_set_phys_id,
-};
-
-static const struct ethtool_ops ethtool_ops = {
- .get_drvinfo = ewrk3_get_drvinfo,
- .get_settings = ewrk3_get_settings,
- .set_settings = ewrk3_set_settings,
- .get_link = ewrk3_get_link,
- .set_phys_id = ewrk3_set_phys_id,
-};
-
-/*
- ** Perform IOCTL call functions here. Some are privileged operations and the
- ** effective uid is checked in those cases.
- */
-static int ewrk3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
-{
- struct ewrk3_private *lp = netdev_priv(dev);
- struct ewrk3_ioctl *ioc = (struct ewrk3_ioctl *) &rq->ifr_ifru;
- u_long iobase = dev->base_addr;
- int i, j, status = 0;
- u_char csr;
- unsigned long flags;
- union ewrk3_addr {
- u_char addr[HASH_TABLE_LEN * ETH_ALEN];
- u_short val[(HASH_TABLE_LEN * ETH_ALEN) >> 1];
- };
-
- union ewrk3_addr *tmp;
-
- /* All we handle are private IOCTLs */
- if (cmd != EWRK3IOCTL)
- return -EOPNOTSUPP;
-
- tmp = kmalloc(sizeof(union ewrk3_addr), GFP_KERNEL);
- if(tmp==NULL)
- return -ENOMEM;
-
- switch (ioc->cmd) {
- case EWRK3_GET_HWADDR: /* Get the hardware address */
- for (i = 0; i < ETH_ALEN; i++) {
- tmp->addr[i] = dev->dev_addr[i];
- }
- ioc->len = ETH_ALEN;
- if (copy_to_user(ioc->data, tmp->addr, ioc->len))
- status = -EFAULT;
- break;
-
- case EWRK3_SET_HWADDR: /* Set the hardware address */
- if (capable(CAP_NET_ADMIN)) {
- spin_lock_irqsave(&lp->hw_lock, flags);
- csr = inb(EWRK3_CSR);
- csr |= (CSR_TXD | CSR_RXD);
- outb(csr, EWRK3_CSR); /* Disable the TX and RX */
- spin_unlock_irqrestore(&lp->hw_lock, flags);
-
- if (copy_from_user(tmp->addr, ioc->data, ETH_ALEN)) {
- status = -EFAULT;
- break;
- }
- spin_lock_irqsave(&lp->hw_lock, flags);
- for (i = 0; i < ETH_ALEN; i++) {
- dev->dev_addr[i] = tmp->addr[i];
- outb(tmp->addr[i], EWRK3_PAR0 + i);
- }
-
- csr = inb(EWRK3_CSR);
- csr &= ~(CSR_TXD | CSR_RXD); /* Enable the TX and RX */
- outb(csr, EWRK3_CSR);
- spin_unlock_irqrestore(&lp->hw_lock, flags);
- } else {
- status = -EPERM;
- }
-
- break;
- case EWRK3_SET_PROM: /* Set Promiscuous Mode */
- if (capable(CAP_NET_ADMIN)) {
- spin_lock_irqsave(&lp->hw_lock, flags);
- csr = inb(EWRK3_CSR);
- csr |= CSR_PME;
- csr &= ~CSR_MCE;
- outb(csr, EWRK3_CSR);
- spin_unlock_irqrestore(&lp->hw_lock, flags);
- } else {
- status = -EPERM;
- }
-
- break;
- case EWRK3_CLR_PROM: /* Clear Promiscuous Mode */
- if (capable(CAP_NET_ADMIN)) {
- spin_lock_irqsave(&lp->hw_lock, flags);
- csr = inb(EWRK3_CSR);
- csr &= ~CSR_PME;
- outb(csr, EWRK3_CSR);
- spin_unlock_irqrestore(&lp->hw_lock, flags);
- } else {
- status = -EPERM;
- }
-
- break;
- case EWRK3_GET_MCA: /* Get the multicast address table */
- spin_lock_irqsave(&lp->hw_lock, flags);
- if (lp->shmem_length == IO_ONLY) {
- outb(0, EWRK3_IOPR);
- outw(PAGE0_HTE, EWRK3_PIR1);
- for (i = 0; i < (HASH_TABLE_LEN >> 3); i++) {
- tmp->addr[i] = inb(EWRK3_DATA);
- }
- } else {
- outb(0, EWRK3_MPR);
- memcpy_fromio(tmp->addr, lp->shmem + PAGE0_HTE, (HASH_TABLE_LEN >> 3));
- }
- spin_unlock_irqrestore(&lp->hw_lock, flags);
-
- ioc->len = (HASH_TABLE_LEN >> 3);
- if (copy_to_user(ioc->data, tmp->addr, ioc->len))
- status = -EFAULT;
-
- break;
- case EWRK3_SET_MCA: /* Set a multicast address */
- if (capable(CAP_NET_ADMIN)) {
- if (ioc->len > HASH_TABLE_LEN) {
- status = -EINVAL;
- break;
- }
- if (copy_from_user(tmp->addr, ioc->data, ETH_ALEN * ioc->len)) {
- status = -EFAULT;
- break;
- }
- set_multicast_list(dev);
- } else {
- status = -EPERM;
- }
-
- break;
- case EWRK3_CLR_MCA: /* Clear all multicast addresses */
- if (capable(CAP_NET_ADMIN)) {
- set_multicast_list(dev);
- } else {
- status = -EPERM;
- }
-
- break;
- case EWRK3_MCA_EN: /* Enable multicast addressing */
- if (capable(CAP_NET_ADMIN)) {
- spin_lock_irqsave(&lp->hw_lock, flags);
- csr = inb(EWRK3_CSR);
- csr |= CSR_MCE;
- csr &= ~CSR_PME;
- outb(csr, EWRK3_CSR);
- spin_unlock_irqrestore(&lp->hw_lock, flags);
- } else {
- status = -EPERM;
- }
-
- break;
- case EWRK3_GET_STATS: { /* Get the driver statistics */
- struct ewrk3_stats *tmp_stats =
- kmalloc(sizeof(lp->pktStats), GFP_KERNEL);
- if (!tmp_stats) {
- status = -ENOMEM;
- break;
- }
-
- spin_lock_irqsave(&lp->hw_lock, flags);
- memcpy(tmp_stats, &lp->pktStats, sizeof(lp->pktStats));
- spin_unlock_irqrestore(&lp->hw_lock, flags);
-
- ioc->len = sizeof(lp->pktStats);
- if (copy_to_user(ioc->data, tmp_stats, sizeof(lp->pktStats)))
- status = -EFAULT;
- kfree(tmp_stats);
- break;
- }
- case EWRK3_CLR_STATS: /* Zero out the driver statistics */
- if (capable(CAP_NET_ADMIN)) {
- spin_lock_irqsave(&lp->hw_lock, flags);
- memset(&lp->pktStats, 0, sizeof(lp->pktStats));
- spin_unlock_irqrestore(&lp->hw_lock,flags);
- } else {
- status = -EPERM;
- }
-
- break;
- case EWRK3_GET_CSR: /* Get the CSR Register contents */
- tmp->addr[0] = inb(EWRK3_CSR);
- ioc->len = 1;
- if (copy_to_user(ioc->data, tmp->addr, ioc->len))
- status = -EFAULT;
- break;
- case EWRK3_SET_CSR: /* Set the CSR Register contents */
- if (capable(CAP_NET_ADMIN)) {
- if (copy_from_user(tmp->addr, ioc->data, 1)) {
- status = -EFAULT;
- break;
- }
- outb(tmp->addr[0], EWRK3_CSR);
- } else {
- status = -EPERM;
- }
-
- break;
- case EWRK3_GET_EEPROM: /* Get the EEPROM contents */
- if (capable(CAP_NET_ADMIN)) {
- for (i = 0; i < (EEPROM_MAX >> 1); i++) {
- tmp->val[i] = (short) Read_EEPROM(iobase, i);
- }
- i = EEPROM_MAX;
- tmp->addr[i++] = inb(EWRK3_CMR); /* Config/Management Reg. */
- for (j = 0; j < ETH_ALEN; j++) {
- tmp->addr[i++] = inb(EWRK3_PAR0 + j);
- }
- ioc->len = EEPROM_MAX + 1 + ETH_ALEN;
- if (copy_to_user(ioc->data, tmp->addr, ioc->len))
- status = -EFAULT;
- } else {
- status = -EPERM;
- }
-
- break;
- case EWRK3_SET_EEPROM: /* Set the EEPROM contents */
- if (capable(CAP_NET_ADMIN)) {
- if (copy_from_user(tmp->addr, ioc->data, EEPROM_MAX)) {
- status = -EFAULT;
- break;
- }
- for (i = 0; i < (EEPROM_MAX >> 1); i++) {
- Write_EEPROM(tmp->val[i], iobase, i);
- }
- } else {
- status = -EPERM;
- }
-
- break;
- case EWRK3_GET_CMR: /* Get the CMR Register contents */
- tmp->addr[0] = inb(EWRK3_CMR);
- ioc->len = 1;
- if (copy_to_user(ioc->data, tmp->addr, ioc->len))
- status = -EFAULT;
- break;
- case EWRK3_SET_TX_CUT_THRU: /* Set TX cut through mode */
- if (capable(CAP_NET_ADMIN)) {
- lp->txc = 1;
- } else {
- status = -EPERM;
- }
-
- break;
- case EWRK3_CLR_TX_CUT_THRU: /* Clear TX cut through mode */
- if (capable(CAP_NET_ADMIN)) {
- lp->txc = 0;
- } else {
- status = -EPERM;
- }
-
- break;
- default:
- status = -EOPNOTSUPP;
- }
- kfree(tmp);
- return status;
-}
-
-#ifdef MODULE
-static struct net_device *ewrk3_devs[MAX_NUM_EWRK3S];
-static int ndevs;
-static int io[MAX_NUM_EWRK3S+1] = { 0x300, 0, };
-
-module_param_array(io, int, NULL, 0);
-module_param_array(irq, byte, NULL, 0);
-MODULE_PARM_DESC(io, "EtherWORKS 3 I/O base address(es)");
-MODULE_PARM_DESC(irq, "EtherWORKS 3 IRQ number(s)");
-
-static __exit void ewrk3_exit_module(void)
-{
- int i;
-
- for( i=0; i<ndevs; i++ ) {
- struct net_device *dev = ewrk3_devs[i];
- struct ewrk3_private *lp = netdev_priv(dev);
- ewrk3_devs[i] = NULL;
- unregister_netdev(dev);
- release_region(dev->base_addr, EWRK3_TOTAL_SIZE);
- iounmap(lp->shmem);
- free_netdev(dev);
- }
-}
-
-static __init int ewrk3_init_module(void)
-{
- int i=0;
-
- while( io[i] && irq[i] ) {
- struct net_device *dev
- = alloc_etherdev(sizeof(struct ewrk3_private));
-
- if (!dev)
- break;
-
- if (ewrk3_probe1(dev, io[i], irq[i]) != 0) {
- free_netdev(dev);
- break;
- }
-
- ewrk3_devs[ndevs++] = dev;
- i++;
- }
-
- return ndevs ? 0 : -EIO;
-}
-
-
-/* Hack for breakage in new module stuff */
-module_exit(ewrk3_exit_module);
-module_init(ewrk3_init_module);
-#endif /* MODULE */
-MODULE_LICENSE("GPL");
+++ /dev/null
-/*
- Written 1994 by David C. Davies.
-
- Copyright 1994 Digital Equipment Corporation.
-
- This software may be used and distributed according to the terms of the
- GNU General Public License, incorporated herein by reference.
-
- The author may be reached as davies@wanton.lkg.dec.com or Digital
- Equipment Corporation, 550 King Street, Littleton MA 01460.
-
- =========================================================================
-*/
-
-/*
-** I/O Address Register Map
-*/
-#define EWRK3_CSR iobase+0x00 /* Control and Status Register */
-#define EWRK3_CR iobase+0x01 /* Control Register */
-#define EWRK3_ICR iobase+0x02 /* Interrupt Control Register */
-#define EWRK3_TSR iobase+0x03 /* Transmit Status Register */
-#define EWRK3_RSVD1 iobase+0x04 /* RESERVED */
-#define EWRK3_RSVD2 iobase+0x05 /* RESERVED */
-#define EWRK3_FMQ iobase+0x06 /* Free Memory Queue */
-#define EWRK3_FMQC iobase+0x07 /* Free Memory Queue Counter */
-#define EWRK3_RQ iobase+0x08 /* Receive Queue */
-#define EWRK3_RQC iobase+0x09 /* Receive Queue Counter */
-#define EWRK3_TQ iobase+0x0a /* Transmit Queue */
-#define EWRK3_TQC iobase+0x0b /* Transmit Queue Counter */
-#define EWRK3_TDQ iobase+0x0c /* Transmit Done Queue */
-#define EWRK3_TDQC iobase+0x0d /* Transmit Done Queue Counter */
-#define EWRK3_PIR1 iobase+0x0e /* Page Index Register 1 */
-#define EWRK3_PIR2 iobase+0x0f /* Page Index Register 2 */
-#define EWRK3_DATA iobase+0x10 /* Data Register */
-#define EWRK3_IOPR iobase+0x11 /* I/O Page Register */
-#define EWRK3_IOBR iobase+0x12 /* I/O Base Register */
-#define EWRK3_MPR iobase+0x13 /* Memory Page Register */
-#define EWRK3_MBR iobase+0x14 /* Memory Base Register */
-#define EWRK3_APROM iobase+0x15 /* Address PROM */
-#define EWRK3_EPROM1 iobase+0x16 /* EEPROM Data Register 1 */
-#define EWRK3_EPROM2 iobase+0x17 /* EEPROM Data Register 2 */
-#define EWRK3_PAR0 iobase+0x18 /* Physical Address Register 0 */
-#define EWRK3_PAR1 iobase+0x19 /* Physical Address Register 1 */
-#define EWRK3_PAR2 iobase+0x1a /* Physical Address Register 2 */
-#define EWRK3_PAR3 iobase+0x1b /* Physical Address Register 3 */
-#define EWRK3_PAR4 iobase+0x1c /* Physical Address Register 4 */
-#define EWRK3_PAR5 iobase+0x1d /* Physical Address Register 5 */
-#define EWRK3_CMR iobase+0x1e /* Configuration/Management Register */
-
-/*
-** Control Page Map
-*/
-#define PAGE0_FMQ 0x000 /* Free Memory Queue */
-#define PAGE0_RQ 0x080 /* Receive Queue */
-#define PAGE0_TQ 0x100 /* Transmit Queue */
-#define PAGE0_TDQ 0x180 /* Transmit Done Queue */
-#define PAGE0_HTE 0x200 /* Hash Table Entries */
-#define PAGE0_RSVD 0x240 /* RESERVED */
-#define PAGE0_USRD 0x600 /* User Data */
-
-/*
-** Control and Status Register bit definitions (EWRK3_CSR)
-*/
-#define CSR_RA 0x80 /* Runt Accept */
-#define CSR_PME 0x40 /* Promiscuous Mode Enable */
-#define CSR_MCE 0x20 /* Multicast Enable */
-#define CSR_TNE 0x08 /* TX Done Queue Not Empty */
-#define CSR_RNE 0x04 /* RX Queue Not Empty */
-#define CSR_TXD 0x02 /* TX Disable */
-#define CSR_RXD 0x01 /* RX Disable */
-
-/*
-** Control Register bit definitions (EWRK3_CR)
-*/
-#define CR_APD 0x80 /* Auto Port Disable */
-#define CR_PSEL 0x40 /* Port Select (0->TP port) */
-#define CR_LBCK 0x20 /* LoopBaCK enable */
-#define CR_FDUP 0x10 /* Full DUPlex enable */
-#define CR_FBUS 0x08 /* Fast BUS enable (ISA clk > 8.33MHz) */
-#define CR_EN_16 0x04 /* ENable 16 bit memory accesses */
-#define CR_LED 0x02 /* LED (1-> turn on) */
-
-/*
-** Interrupt Control Register bit definitions (EWRK3_ICR)
-*/
-#define ICR_IE 0x80 /* Interrupt Enable */
-#define ICR_IS 0x60 /* Interrupt Selected */
-#define ICR_TNEM 0x08 /* TNE Mask (0->mask) */
-#define ICR_RNEM 0x04 /* RNE Mask (0->mask) */
-#define ICR_TXDM 0x02 /* TXD Mask (0->mask) */
-#define ICR_RXDM 0x01 /* RXD Mask (0->mask) */
-
-/*
-** Transmit Status Register bit definitions (EWRK3_TSR)
-*/
-#define TSR_NCL 0x80 /* No Carrier Loopback */
-#define TSR_ID 0x40 /* Initially Deferred */
-#define TSR_LCL 0x20 /* Late CoLlision */
-#define TSR_ECL 0x10 /* Excessive CoLlisions */
-#define TSR_RCNTR 0x0f /* Retries CouNTeR */
-
-/*
-** I/O Page Register bit definitions (EWRK3_IOPR)
-*/
-#define EEPROM_INIT 0xc0 /* EEPROM INIT command */
-#define EEPROM_WR_EN 0xc8 /* EEPROM WRITE ENABLE command */
-#define EEPROM_WR 0xd0 /* EEPROM WRITE command */
-#define EEPROM_WR_DIS 0xd8 /* EEPROM WRITE DISABLE command */
-#define EEPROM_RD 0xe0 /* EEPROM READ command */
-
-/*
-** I/O Base Register bit definitions (EWRK3_IOBR)
-*/
-#define EISA_REGS_EN 0x20 /* Enable EISA ID and Control Registers */
-#define EISA_IOB 0x1f /* Compare bits for I/O Base Address */
-
-/*
-** I/O Configuration/Management Register bit definitions (EWRK3_CMR)
-*/
-#define CMR_RA 0x80 /* Read Ahead */
-#define CMR_WB 0x40 /* Write Behind */
-#define CMR_LINK 0x20 /* 0->TP */
-#define CMR_POLARITY 0x10 /* Informational */
-#define CMR_NO_EEPROM 0x0c /* NO_EEPROM<1:0> pin status */
-#define CMR_HS 0x08 /* Hard Strapped pin status (LeMAC2) */
-#define CMR_PNP 0x04 /* Plug 'n Play */
-#define CMR_DRAM 0x02 /* 0-> 1DRAM, 1-> 2 DRAM on board */
-#define CMR_0WS 0x01 /* Zero Wait State */
-
-/*
-** MAC Receive Status Register bit definitions
-*/
-
-#define R_ROK 0x80 /* Receive OK summary */
-#define R_IAM 0x10 /* Individual Address Match */
-#define R_MCM 0x08 /* MultiCast Match */
-#define R_DBE 0x04 /* Dribble Bit Error */
-#define R_CRC 0x02 /* CRC error */
-#define R_PLL 0x01 /* Phase Lock Lost */
-
-/*
-** MAC Transmit Control Register bit definitions
-*/
-
-#define TCR_SQEE 0x40 /* SQE Enable - look for heartbeat */
-#define TCR_SED 0x20 /* Stop when Error Detected */
-#define TCR_QMODE 0x10 /* Q_MODE */
-#define TCR_LAB 0x08 /* Less Aggressive Backoff */
-#define TCR_PAD 0x04 /* PAD Runt Packets */
-#define TCR_IFC 0x02 /* Insert Frame Check */
-#define TCR_ISA 0x01 /* Insert Source Address */
-
-/*
-** MAC Transmit Status Register bit definitions
-*/
-
-#define T_VSTS 0x80 /* Valid STatuS */
-#define T_CTU 0x40 /* Cut Through Used */
-#define T_SQE 0x20 /* Signal Quality Error */
-#define T_NCL 0x10 /* No Carrier Loopback */
-#define T_LCL 0x08 /* Late Collision */
-#define T_ID 0x04 /* Initially Deferred */
-#define T_COLL 0x03 /* COLLision status */
-#define T_XCOLL 0x03 /* Excessive Collisions */
-#define T_MCOLL 0x02 /* Multiple Collisions */
-#define T_OCOLL 0x01 /* One Collision */
-#define T_NOCOLL 0x00 /* No Collisions */
-#define T_XUR 0x03 /* Excessive Underruns */
-#define T_TXE 0x7f /* TX Errors */
-
-/*
-** EISA Configuration Register bit definitions
-*/
-
-#define EISA_ID iobase + 0x0c80 /* EISA ID Registers */
-#define EISA_ID0 iobase + 0x0c80 /* EISA ID Register 0 */
-#define EISA_ID1 iobase + 0x0c81 /* EISA ID Register 1 */
-#define EISA_ID2 iobase + 0x0c82 /* EISA ID Register 2 */
-#define EISA_ID3 iobase + 0x0c83 /* EISA ID Register 3 */
-#define EISA_CR iobase + 0x0c84 /* EISA Control Register */
-
-/*
-** EEPROM BYTES
-*/
-#define EEPROM_MEMB 0x00
-#define EEPROM_IOB 0x01
-#define EEPROM_EISA_ID0 0x02
-#define EEPROM_EISA_ID1 0x03
-#define EEPROM_EISA_ID2 0x04
-#define EEPROM_EISA_ID3 0x05
-#define EEPROM_MISC0 0x06
-#define EEPROM_MISC1 0x07
-#define EEPROM_PNAME7 0x08
-#define EEPROM_PNAME6 0x09
-#define EEPROM_PNAME5 0x0a
-#define EEPROM_PNAME4 0x0b
-#define EEPROM_PNAME3 0x0c
-#define EEPROM_PNAME2 0x0d
-#define EEPROM_PNAME1 0x0e
-#define EEPROM_PNAME0 0x0f
-#define EEPROM_SWFLAGS 0x10
-#define EEPROM_HWCAT 0x11
-#define EEPROM_NETMAN2 0x12
-#define EEPROM_REVLVL 0x13
-#define EEPROM_NETMAN0 0x14
-#define EEPROM_NETMAN1 0x15
-#define EEPROM_CHIPVER 0x16
-#define EEPROM_SETUP 0x17
-#define EEPROM_PADDR0 0x18
-#define EEPROM_PADDR1 0x19
-#define EEPROM_PADDR2 0x1a
-#define EEPROM_PADDR3 0x1b
-#define EEPROM_PADDR4 0x1c
-#define EEPROM_PADDR5 0x1d
-#define EEPROM_PA_CRC 0x1e
-#define EEPROM_CHKSUM 0x1f
-
-/*
-** EEPROM bytes for checksumming
-*/
-#define EEPROM_MAX 32 /* bytes */
-
-/*
-** EEPROM MISCELLANEOUS FLAGS
-*/
-#define RBE_SHADOW 0x0100 /* Remote Boot Enable Shadow */
-#define READ_AHEAD 0x0080 /* Read Ahead feature */
-#define IRQ_SEL2 0x0070 /* IRQ line selection (LeMAC2) */
-#define IRQ_SEL 0x0060 /* IRQ line selection */
-#define FAST_BUS 0x0008 /* ISA Bus speeds > 8.33MHz */
-#define ENA_16 0x0004 /* Enables 16 bit memory transfers */
-#define WRITE_BEHIND 0x0002 /* Write Behind feature */
-#define _0WS_ENA 0x0001 /* Zero Wait State Enable */
-
-/*
-** EEPROM NETWORK MANAGEMENT FLAGS
-*/
-#define NETMAN_POL 0x04 /* Polarity defeat */
-#define NETMAN_LINK 0x02 /* Link defeat */
-#define NETMAN_CCE 0x01 /* Custom Counters Enable */
-
-/*
-** EEPROM SW FLAGS
-*/
-#define SW_SQE 0x10 /* Signal Quality Error */
-#define SW_LAB 0x08 /* Less Aggressive Backoff */
-#define SW_INIT 0x04 /* Initialized */
-#define SW_TIMEOUT 0x02 /* 0:2.5 mins, 1: 30 secs */
-#define SW_REMOTE 0x01 /* Remote Boot Enable -> 1 */
-
-/*
-** EEPROM SETUP FLAGS
-*/
-#define SETUP_APD 0x80 /* AutoPort Disable */
-#define SETUP_PS 0x40 /* Port Select */
-#define SETUP_MP 0x20 /* MultiPort */
-#define SETUP_1TP 0x10 /* 1 port, TP */
-#define SETUP_1COAX 0x00 /* 1 port, Coax */
-#define SETUP_DRAM 0x02 /* Number of DRAMS on board */
-
-/*
-** EEPROM MANAGEMENT FLAGS
-*/
-#define MGMT_CCE 0x01 /* Custom Counters Enable */
-
-/*
-** EEPROM VERSIONS
-*/
-#define LeMAC 0x11
-#define LeMAC2 0x12
-
-/*
-** Miscellaneous
-*/
-
-#define EEPROM_WAIT_TIME 1000 /* Number of microseconds */
-#define EISA_EN 0x0001 /* Enable EISA bus buffers */
-
-#define HASH_TABLE_LEN 512 /* Bits */
-
-#define XCT 0x80 /* Transmit Cut Through */
-#define PRELOAD 16 /* 4 long words */
-
-#define MASK_INTERRUPTS 1
-#define UNMASK_INTERRUPTS 0
-
-#define EEPROM_OFFSET(a) ((u_short)((u_long)(a)))
-
-/*
-** Include the IOCTL stuff
-*/
-#include <linux/sockios.h>
-
-#define EWRK3IOCTL SIOCDEVPRIVATE
-
-struct ewrk3_ioctl {
- unsigned short cmd; /* Command to run */
- unsigned short len; /* Length of the data buffer */
- unsigned char __user *data; /* Pointer to the data buffer */
-};
-
-/*
-** Recognised commands for the driver
-*/
-#define EWRK3_GET_HWADDR 0x01 /* Get the hardware address */
-#define EWRK3_SET_HWADDR 0x02 /* Get the hardware address */
-#define EWRK3_SET_PROM 0x03 /* Set Promiscuous Mode */
-#define EWRK3_CLR_PROM 0x04 /* Clear Promiscuous Mode */
-#define EWRK3_SAY_BOO 0x05 /* Say "Boo!" to the kernel log file */
-#define EWRK3_GET_MCA 0x06 /* Get a multicast address */
-#define EWRK3_SET_MCA 0x07 /* Set a multicast address */
-#define EWRK3_CLR_MCA 0x08 /* Clear a multicast address */
-#define EWRK3_MCA_EN 0x09 /* Enable a multicast address group */
-#define EWRK3_GET_STATS 0x0a /* Get the driver statistics */
-#define EWRK3_CLR_STATS 0x0b /* Zero out the driver statistics */
-#define EWRK3_GET_CSR 0x0c /* Get the CSR Register contents */
-#define EWRK3_SET_CSR 0x0d /* Set the CSR Register contents */
-#define EWRK3_GET_EEPROM 0x0e /* Get the EEPROM contents */
-#define EWRK3_SET_EEPROM 0x0f /* Set the EEPROM contents */
-#define EWRK3_GET_CMR 0x10 /* Get the CMR Register contents */
-#define EWRK3_CLR_TX_CUT_THRU 0x11 /* Clear the TX cut through mode */
-#define EWRK3_SET_TX_CUT_THRU 0x12 /* Set the TX cut through mode */
projects / linux-2.6-microblaze.git / commitdiff