X-Git-Url: http://git.monstr.eu/?a=blobdiff_plain;f=arch%2Farm%2Fboot%2Fdts%2Fgemini-dlink-dir-685.dts;h=cc39289e99dd131a2da7a9aecc2a34e424ab85e9;hb=cc58045486d0f938662b01025c855fd4aea89ea6;hp=e2030ba16512f52c927e0b53a2fca54b9a613490;hpb=1d4c79ed324ad780cfc3ad38364ba1fd585dd2a8;p=linux-2.6-microblaze.git

diff --git a/arch/arm/boot/dts/gemini-dlink-dir-685.dts b/arch/arm/boot/dts/gemini-dlink-dir-685.dts
index e2030ba16512..cc39289e99dd 100644
--- a/arch/arm/boot/dts/gemini-dlink-dir-685.dts
+++ b/arch/arm/boot/dts/gemini-dlink-dir-685.dts
@@ -119,13 +119,11 @@
 
 	/*
 	 * This is a Sunon Maglev GM0502PFV2-8 cooling fan @10000 RPM.
-	 * Since the platform has no temperature sensor, this is controlled
-	 * from userspace by using the hard disks S.M.A.R.T. temperature
 	 * sensor. It is turned on when the temperature exceeds 46 degrees
 	 * and turned off when the temperatures goes below 41 degrees
 	 * (celsius).
 	 */
-	gpio-fan {
+	fan0: gpio-fan {
 		compatible = "gpio-fan";
 		/* Collides with IDE */
 		gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
@@ -133,6 +131,40 @@
 		#cooling-cells = <2>;
 	};
 
+	thermal-zones {
+		chassis-thermal {
+			/* Poll every 20 seconds */
+			polling-delay = <20000>;
+			/* Poll every 2nd second when cooling */
+			polling-delay-passive = <2000>;
+			/*  Use the thermal sensor in the hard drive */
+			thermal-sensors = <&drive0>;
+
+			/* Tripping points from the fan.script in the rootfs */
+			trips {
+				alert: chassis-alert {
+					/* At 43 degrees turn on the fan */
+					temperature = <43000>;
+					hysteresis = <3000>;
+					type = "active";
+				};
+				crit: chassis-crit {
+					/* Just shut down at 60 degrees */
+					temperature = <60000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&alert>;
+					cooling-device = <&fan0 1 1>;
+				};
+			};
+		};
+	};
+
 	/*
 	 * The touchpad input is connected to a GPIO bit-banged
 	 * I2C bus.
@@ -443,8 +475,18 @@
 			};
 		};
 
-		ata@63000000 {
+		ide@63000000 {
 			status = "okay";
+
+			/*
+			 * This drive may have a temperature sensor with a
+			 * thermal zone we can use for thermal control of the
+			 * chassis temperature using the fan.
+			 */
+			drive0: ide-port@0 {
+				reg = <0>;
+				#thermal-sensor-cells = <0>;
+			};
 		};
 
 		display-controller@6a000000 {