# below for IPv6 doesn't apply here, because, on IPv4, administrative MTU
# changes alone won't affect PMTU
#
+# - pmtu_vti4_udp_exception
+# Same as pmtu_vti4_exception, but using ESP-in-UDP
+#
+# - pmtu_vti4_udp_routed_exception
+# Set up vti tunnel on top of veth connected through routing namespace and
+# add xfrm states and policies with ESP-in-UDP encapsulation. Check that
+# route exception is not created if link layer MTU is not exceeded, then
+# lower MTU on second part of routed environment and check that exception
+# is created with the expected PMTU.
+#
# - pmtu_vti6_exception
# Set up vti6 tunnel on top of veth, with xfrm states and policies, in two
# namespaces with matching endpoints. Check that route exception is
# decrease and increase MTU of tunnel, checking that route exception PMTU
# changes accordingly
#
+# - pmtu_vti6_udp_exception
+# Same as pmtu_vti6_exception, but using ESP-in-UDP
+#
+# - pmtu_vti6_udp_routed_exception
+# Same as pmtu_vti6_udp_routed_exception but with routing between vti
+# endpoints
+#
# - pmtu_vti4_default_mtu
# Set up vti4 tunnel on top of veth, in two namespaces with matching
# endpoints. Check that MTU assigned to vti interface is the MTU of the
pmtu_ipv6_ipv6_exception IPv6 over IPv6: PMTU exceptions 1
pmtu_vti6_exception vti6: PMTU exceptions 0
pmtu_vti4_exception vti4: PMTU exceptions 0
+ pmtu_vti6_udp_exception vti6: PMTU exceptions (ESP-in-UDP) 0
+ pmtu_vti4_udp_exception vti4: PMTU exceptions (ESP-in-UDP) 0
+ pmtu_vti6_udp_routed_exception vti6: PMTU exceptions, routed (ESP-in-UDP) 0
+ pmtu_vti4_udp_routed_exception vti4: PMTU exceptions, routed (ESP-in-UDP) 0
pmtu_vti4_default_mtu vti4: default MTU assignment 0
pmtu_vti6_default_mtu vti6: default MTU assignment 0
pmtu_vti4_link_add_mtu vti4: MTU setting on link creation 0
ns_c="ip netns exec ${NS_C}"
ns_r1="ip netns exec ${NS_R1}"
ns_r2="ip netns exec ${NS_R2}"
-
# Addressing and routing for tests with routers: four network segments, with
# index SEGMENT between 1 and 4, a common prefix (PREFIX4 or PREFIX6) and an
# identifier ID, which is 1 for hosts (A and B), 2 for routers (R1 and R2).
A ${prefix6}:${b_r2}::1 ${prefix6}:${a_r2}::2
B default ${prefix6}:${b_r1}::2
"
-
USE_NH="no"
# ns family nh id destination gateway
nexthops="
err_buf=
tcpdump_pids=
+nettest_pids=
err() {
err_buf="${err_buf}${1}
setup_vti 6 ${veth6_a_addr} ${veth6_b_addr} ${tunnel6_a_addr} ${tunnel6_b_addr} ${tunnel6_mask}
}
+setup_vti4routed() {
+ setup_vti 4 ${prefix4}.${a_r1}.1 ${prefix4}.${b_r1}.1 ${tunnel4_a_addr} ${tunnel4_b_addr} ${tunnel4_mask}
+}
+
+setup_vti6routed() {
+ setup_vti 6 ${prefix6}:${a_r1}::1 ${prefix6}:${b_r1}::1 ${tunnel6_a_addr} ${tunnel6_b_addr} ${tunnel6_mask}
+}
+
setup_vxlan_or_geneve() {
type="${1}"
a_addr="${2}"
proto=${1}
veth_a_addr="${2}"
veth_b_addr="${3}"
+ encap=${4}
- run_cmd ${ns_a} ip -${proto} xfrm state add src ${veth_a_addr} dst ${veth_b_addr} spi 0x1000 proto esp aead 'rfc4106(gcm(aes))' 0x0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f 128 mode tunnel || return 1
- run_cmd ${ns_a} ip -${proto} xfrm state add src ${veth_b_addr} dst ${veth_a_addr} spi 0x1001 proto esp aead 'rfc4106(gcm(aes))' 0x0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f 128 mode tunnel
+ run_cmd ${ns_a} ip -${proto} xfrm state add src ${veth_a_addr} dst ${veth_b_addr} spi 0x1000 proto esp aead 'rfc4106(gcm(aes))' 0x0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f 128 mode tunnel ${encap} || return 1
+ run_cmd ${ns_a} ip -${proto} xfrm state add src ${veth_b_addr} dst ${veth_a_addr} spi 0x1001 proto esp aead 'rfc4106(gcm(aes))' 0x0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f 128 mode tunnel ${encap}
run_cmd ${ns_a} ip -${proto} xfrm policy add dir out mark 10 tmpl src ${veth_a_addr} dst ${veth_b_addr} proto esp mode tunnel
run_cmd ${ns_a} ip -${proto} xfrm policy add dir in mark 10 tmpl src ${veth_b_addr} dst ${veth_a_addr} proto esp mode tunnel
- run_cmd ${ns_b} ip -${proto} xfrm state add src ${veth_a_addr} dst ${veth_b_addr} spi 0x1000 proto esp aead 'rfc4106(gcm(aes))' 0x0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f 128 mode tunnel
- run_cmd ${ns_b} ip -${proto} xfrm state add src ${veth_b_addr} dst ${veth_a_addr} spi 0x1001 proto esp aead 'rfc4106(gcm(aes))' 0x0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f 128 mode tunnel
+ run_cmd ${ns_b} ip -${proto} xfrm state add src ${veth_a_addr} dst ${veth_b_addr} spi 0x1000 proto esp aead 'rfc4106(gcm(aes))' 0x0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f 128 mode tunnel ${encap}
+ run_cmd ${ns_b} ip -${proto} xfrm state add src ${veth_b_addr} dst ${veth_a_addr} spi 0x1001 proto esp aead 'rfc4106(gcm(aes))' 0x0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f 128 mode tunnel ${encap}
run_cmd ${ns_b} ip -${proto} xfrm policy add dir out mark 10 tmpl src ${veth_b_addr} dst ${veth_a_addr} proto esp mode tunnel
run_cmd ${ns_b} ip -${proto} xfrm policy add dir in mark 10 tmpl src ${veth_a_addr} dst ${veth_b_addr} proto esp mode tunnel
}
+setup_nettest_xfrm() {
+ which nettest >/dev/null
+ if [ $? -ne 0 ]; then
+ echo "'nettest' command not found; skipping tests"
+ return 1
+ fi
+
+ [ ${1} -eq 6 ] && proto="-6" || proto=""
+ port=${2}
+
+ run_cmd ${ns_a} nettest ${proto} -q -D -s -x -p ${port} -t 5 &
+ nettest_pids="${nettest_pids} $!"
+
+ run_cmd ${ns_b} nettest ${proto} -q -D -s -x -p ${port} -t 5 &
+ nettest_pids="${nettest_pids} $!"
+}
+
setup_xfrm4() {
setup_xfrm 4 ${veth4_a_addr} ${veth4_b_addr}
}
setup_xfrm 6 ${veth6_a_addr} ${veth6_b_addr}
}
+setup_xfrm4udp() {
+ setup_xfrm 4 ${veth4_a_addr} ${veth4_b_addr} "encap espinudp 4500 4500 0.0.0.0"
+ setup_nettest_xfrm 4 4500
+}
+
+setup_xfrm6udp() {
+ setup_xfrm 6 ${veth6_a_addr} ${veth6_b_addr} "encap espinudp 4500 4500 0.0.0.0"
+ setup_nettest_xfrm 6 4500
+}
+
+setup_xfrm4udprouted() {
+ setup_xfrm 4 ${prefix4}.${a_r1}.1 ${prefix4}.${b_r1}.1 "encap espinudp 4500 4500 0.0.0.0"
+ setup_nettest_xfrm 4 4500
+}
+
+setup_xfrm6udprouted() {
+ setup_xfrm 6 ${prefix6}:${a_r1}::1 ${prefix6}:${b_r1}::1 "encap espinudp 4500 4500 0.0.0.0"
+ setup_nettest_xfrm 6 4500
+}
+
setup_routing_old() {
for i in ${routes}; do
[ "${ns}" = "" ] && ns="${i}" && continue
done
tcpdump_pids=
+ for pid in ${nettest_pids}; do
+ kill ${pid}
+ done
+ nettest_pids=
+
for n in ${NS_A} ${NS_B} ${NS_C} ${NS_R1} ${NS_R2}; do
ip netns del ${n} 2> /dev/null
done
return ${fail}
}
+test_pmtu_vti4_udp_exception() {
+ setup namespaces veth vti4 xfrm4udp || return $ksft_skip
+ trace "${ns_a}" veth_a "${ns_b}" veth_b \
+ "${ns_a}" vti4_a "${ns_b}" vti4_b
+
+ veth_mtu=1500
+ vti_mtu=$((veth_mtu - 20))
+
+ # UDP SPI SN IV ICV pad length next header
+ esp_payload_rfc4106=$((vti_mtu - 8 - 4 - 4 - 8 - 16 - 1 - 1))
+ ping_payload=$((esp_payload_rfc4106 - 28))
+
+ mtu "${ns_a}" veth_a ${veth_mtu}
+ mtu "${ns_b}" veth_b ${veth_mtu}
+ mtu "${ns_a}" vti4_a ${vti_mtu}
+ mtu "${ns_b}" vti4_b ${vti_mtu}
+
+ # Send DF packet without exceeding link layer MTU, check that no
+ # exception is created
+ run_cmd ${ns_a} ping -q -M want -i 0.1 -w 1 -s ${ping_payload} ${tunnel4_b_addr}
+ pmtu="$(route_get_dst_pmtu_from_exception "${ns_a}" ${tunnel4_b_addr})"
+ check_pmtu_value "" "${pmtu}" "sending packet smaller than PMTU (IP payload length ${esp_payload_rfc4106})" || return 1
+
+ # Now exceed link layer MTU by one byte, check that exception is created
+ # with the right PMTU value
+ run_cmd ${ns_a} ping -q -M want -i 0.1 -w 1 -s $((ping_payload + 1)) ${tunnel4_b_addr}
+ pmtu="$(route_get_dst_pmtu_from_exception "${ns_a}" ${tunnel4_b_addr})"
+ check_pmtu_value "${esp_payload_rfc4106}" "${pmtu}" "exceeding PMTU (IP payload length $((esp_payload_rfc4106 + 1)))"
+}
+
+test_pmtu_vti6_udp_exception() {
+ setup namespaces veth vti6 xfrm6udp || return $ksft_skip
+ trace "${ns_a}" veth_a "${ns_b}" veth_b \
+ "${ns_a}" vti6_a "${ns_b}" vti6_b
+ fail=0
+
+ # Create route exception by exceeding link layer MTU
+ mtu "${ns_a}" veth_a 4000
+ mtu "${ns_b}" veth_b 4000
+ mtu "${ns_a}" vti6_a 5000
+ mtu "${ns_b}" vti6_b 5000
+ run_cmd ${ns_a} ${ping6} -q -i 0.1 -w 1 -s 60000 ${tunnel6_b_addr}
+
+ # Check that exception was created
+ pmtu="$(route_get_dst_pmtu_from_exception "${ns_a}" ${tunnel6_b_addr})"
+ check_pmtu_value any "${pmtu}" "creating tunnel exceeding link layer MTU" || return 1
+
+ # Decrease tunnel MTU, check for PMTU decrease in route exception
+ mtu "${ns_a}" vti6_a 3000
+ pmtu="$(route_get_dst_pmtu_from_exception "${ns_a}" ${tunnel6_b_addr})"
+ check_pmtu_value "3000" "${pmtu}" "decreasing tunnel MTU" || fail=1
+
+ # Increase tunnel MTU, check for PMTU increase in route exception
+ mtu "${ns_a}" vti6_a 9000
+ pmtu="$(route_get_dst_pmtu_from_exception "${ns_a}" ${tunnel6_b_addr})"
+ check_pmtu_value "9000" "${pmtu}" "increasing tunnel MTU" || fail=1
+
+ return ${fail}
+}
+
+test_pmtu_vti4_udp_routed_exception() {
+ setup namespaces routing vti4routed xfrm4udprouted || return $ksft_skip
+ trace "${ns_a}" veth_A-R1 "${ns_b}" veth_B-R1 \
+ "${ns_a}" vti4_a "${ns_b}" vti4_b
+
+ veth_mtu=1500
+ vti_mtu=$((veth_mtu - 20))
+
+ # UDP SPI SN IV ICV pad length next header
+ esp_payload_rfc4106=$((vti_mtu - 8 - 4 - 4 - 8 - 16 - 1 - 1))
+ ping_payload=$((esp_payload_rfc4106 - 28))
+
+ mtu "${ns_a}" veth_A-R1 ${veth_mtu}
+ mtu "${ns_r1}" veth_R1-A ${veth_mtu}
+ mtu "${ns_b}" veth_B-R1 ${veth_mtu}
+ mtu "${ns_r1}" veth_R1-B ${veth_mtu}
+
+ mtu "${ns_a}" vti4_a ${vti_mtu}
+ mtu "${ns_b}" vti4_b ${vti_mtu}
+
+ # Send DF packet without exceeding link layer MTU, check that no
+ # exception is created
+ run_cmd ${ns_a} ping -q -M want -i 0.1 -w 1 -s ${ping_payload} ${tunnel4_b_addr}
+ pmtu="$(route_get_dst_pmtu_from_exception "${ns_a}" ${tunnel4_b_addr})"
+ check_pmtu_value "" "${pmtu}" "sending packet smaller than PMTU (IP payload length ${esp_payload_rfc4106})" || return 1
+
+ # Now decrease link layer MTU by 8 bytes on R1, check that exception is created
+ # with the right PMTU value
+ mtu "${ns_r1}" veth_R1-B $((veth_mtu - 8))
+ run_cmd ${ns_a} ping -q -M want -i 0.1 -w 1 -s $((ping_payload)) ${tunnel4_b_addr}
+ pmtu="$(route_get_dst_pmtu_from_exception "${ns_a}" ${tunnel4_b_addr})"
+ check_pmtu_value "$((esp_payload_rfc4106 - 8))" "${pmtu}" "exceeding PMTU (IP payload length $((esp_payload_rfc4106)))"
+}
+
+test_pmtu_vti6_udp_routed_exception() {
+ setup namespaces routing vti6routed xfrm6udprouted || return $ksft_skip
+ trace "${ns_a}" veth_A-R1 "${ns_b}" veth_B-R1 \
+ "${ns_a}" vti6_a "${ns_b}" vti6_b
+
+ veth_mtu=1500
+ vti_mtu=$((veth_mtu - 40))
+
+ # UDP SPI SN IV ICV pad length next header
+ esp_payload_rfc4106=$((vti_mtu - 8 - 4 - 4 - 8 - 16 - 1 - 1))
+ ping_payload=$((esp_payload_rfc4106 - 48))
+
+ mtu "${ns_a}" veth_A-R1 ${veth_mtu}
+ mtu "${ns_r1}" veth_R1-A ${veth_mtu}
+ mtu "${ns_b}" veth_B-R1 ${veth_mtu}
+ mtu "${ns_r1}" veth_R1-B ${veth_mtu}
+
+ # mtu "${ns_a}" vti6_a ${vti_mtu}
+ # mtu "${ns_b}" vti6_b ${vti_mtu}
+
+ run_cmd ${ns_a} ${ping6} -q -M want -i 0.1 -w 1 -s ${ping_payload} ${tunnel6_b_addr}
+
+ # Check that exception was not created
+ pmtu="$(route_get_dst_pmtu_from_exception "${ns_a}" ${tunnel6_b_addr})"
+ check_pmtu_value "" "${pmtu}" "sending packet smaller than PMTU (IP payload length ${esp_payload_rfc4106})" || return 1
+
+ # Now decrease link layer MTU by 8 bytes on R1, check that exception is created
+ # with the right PMTU value
+ mtu "${ns_r1}" veth_R1-B $((veth_mtu - 8))
+ run_cmd ${ns_a} ${ping6} -q -M want -i 0.1 -w 1 -s $((ping_payload)) ${tunnel6_b_addr}
+ pmtu="$(route_get_dst_pmtu_from_exception "${ns_a}" ${tunnel6_b_addr})"
+ check_pmtu_value "$((esp_payload_rfc4106 - 8))" "${pmtu}" "exceeding PMTU (IP payload length $((esp_payload_rfc4106)))"
+
+}
+
test_pmtu_vti4_default_mtu() {
setup namespaces veth vti4 || return $ksft_skip
projects / linux-2.6-microblaze.git / blobdiff