#include <linux/usb.h>
#include <linux/usb/audio.h>
#include <linux/usb/midi.h>
+#include <linux/bits.h>
#include <sound/control.h>
#include <sound/core.h>
}
/*
- * C-Media CM6206 is based on CM106 with two additional
- * registers that are not documented in the data sheet.
- * Values here are chosen based on sniffing USB traffic
- * under Windows.
+ * CM6206 registers from the CM6206 datasheet rev 2.1
*/
+#define CM6206_REG0_DMA_MASTER BIT(15)
+#define CM6206_REG0_SPDIFO_RATE_48K (2 << 12)
+#define CM6206_REG0_SPDIFO_RATE_96K (7 << 12)
+/* Bit 4 thru 11 is the S/PDIF category code */
+#define CM6206_REG0_SPDIFO_CAT_CODE_GENERAL (0 << 4)
+#define CM6206_REG0_SPDIFO_EMPHASIS_CD BIT(3)
+#define CM6206_REG0_SPDIFO_COPYRIGHT_NA BIT(2)
+#define CM6206_REG0_SPDIFO_NON_AUDIO BIT(1)
+#define CM6206_REG0_SPDIFO_PRO_FORMAT BIT(0)
+
+#define CM6206_REG1_TEST_SEL_CLK BIT(14)
+#define CM6206_REG1_PLLBIN_EN BIT(13)
+#define CM6206_REG1_SOFT_MUTE_EN BIT(12)
+#define CM6206_REG1_GPIO4_OUT BIT(11)
+#define CM6206_REG1_GPIO4_OE BIT(10)
+#define CM6206_REG1_GPIO3_OUT BIT(9)
+#define CM6206_REG1_GPIO3_OE BIT(8)
+#define CM6206_REG1_GPIO2_OUT BIT(7)
+#define CM6206_REG1_GPIO2_OE BIT(6)
+#define CM6206_REG1_GPIO1_OUT BIT(5)
+#define CM6206_REG1_GPIO1_OE BIT(4)
+#define CM6206_REG1_SPDIFO_INVALID BIT(3)
+#define CM6206_REG1_SPDIF_LOOP_EN BIT(2)
+#define CM6206_REG1_SPDIFO_DIS BIT(1)
+#define CM6206_REG1_SPDIFI_MIX BIT(0)
+
+#define CM6206_REG2_DRIVER_ON BIT(15)
+#define CM6206_REG2_HEADP_SEL_SIDE_CHANNELS (0 << 13)
+#define CM6206_REG2_HEADP_SEL_SURROUND_CHANNELS (1 << 13)
+#define CM6206_REG2_HEADP_SEL_CENTER_SUBW (2 << 13)
+#define CM6206_REG2_HEADP_SEL_FRONT_CHANNELS (3 << 13)
+#define CM6206_REG2_MUTE_HEADPHONE_RIGHT BIT(12)
+#define CM6206_REG2_MUTE_HEADPHONE_LEFT BIT(11)
+#define CM6206_REG2_MUTE_REAR_SURROUND_RIGHT BIT(10)
+#define CM6206_REG2_MUTE_REAR_SURROUND_LEFT BIT(9)
+#define CM6206_REG2_MUTE_SIDE_SURROUND_RIGHT BIT(8)
+#define CM6206_REG2_MUTE_SIDE_SURROUND_LEFT BIT(7)
+#define CM6206_REG2_MUTE_SUBWOOFER BIT(6)
+#define CM6206_REG2_MUTE_CENTER BIT(5)
+#define CM6206_REG2_MUTE_RIGHT_FRONT BIT(3)
+#define CM6206_REG2_MUTE_LEFT_FRONT BIT(3)
+#define CM6206_REG2_EN_BTL BIT(2)
+#define CM6206_REG2_MCUCLKSEL_1_5_MHZ (0)
+#define CM6206_REG2_MCUCLKSEL_3_MHZ (1)
+#define CM6206_REG2_MCUCLKSEL_6_MHZ (2)
+#define CM6206_REG2_MCUCLKSEL_12_MHZ (3)
+
+/* Bit 11..13 sets the sensitivity to FLY tuner volume control VP/VD signal */
+#define CM6206_REG3_FLYSPEED_DEFAULT (2 << 11)
+#define CM6206_REG3_VRAP25EN BIT(10)
+#define CM6206_REG3_MSEL1 BIT(9)
+#define CM6206_REG3_SPDIFI_RATE_44_1K BIT(0 << 7)
+#define CM6206_REG3_SPDIFI_RATE_48K BIT(2 << 7)
+#define CM6206_REG3_SPDIFI_RATE_32K BIT(3 << 7)
+#define CM6206_REG3_PINSEL BIT(6)
+#define CM6206_REG3_FOE BIT(5)
+#define CM6206_REG3_ROE BIT(4)
+#define CM6206_REG3_CBOE BIT(3)
+#define CM6206_REG3_LOSE BIT(2)
+#define CM6206_REG3_HPOE BIT(1)
+#define CM6206_REG3_SPDIFI_CANREC BIT(0)
+
+#define CM6206_REG5_DA_RSTN BIT(13)
+#define CM6206_REG5_AD_RSTN BIT(12)
+#define CM6206_REG5_SPDIFO_AD2SPDO BIT(12)
+#define CM6206_REG5_SPDIFO_SEL_FRONT (0 << 9)
+#define CM6206_REG5_SPDIFO_SEL_SIDE_SUR (1 << 9)
+#define CM6206_REG5_SPDIFO_SEL_CEN_LFE (2 << 9)
+#define CM6206_REG5_SPDIFO_SEL_REAR_SUR (3 << 9)
+#define CM6206_REG5_CODECM BIT(8)
+#define CM6206_REG5_EN_HPF BIT(7)
+#define CM6206_REG5_T_SEL_DSDA4 BIT(6)
+#define CM6206_REG5_T_SEL_DSDA3 BIT(5)
+#define CM6206_REG5_T_SEL_DSDA2 BIT(4)
+#define CM6206_REG5_T_SEL_DSDA1 BIT(3)
+#define CM6206_REG5_T_SEL_DSDAD_NORMAL 0
+#define CM6206_REG5_T_SEL_DSDAD_FRONT 4
+#define CM6206_REG5_T_SEL_DSDAD_S_SURROUND 5
+#define CM6206_REG5_T_SEL_DSDAD_CEN_LFE 6
+#define CM6206_REG5_T_SEL_DSDAD_R_SURROUND 7
+
static int snd_usb_cm6206_boot_quirk(struct usb_device *dev)
{
int err = 0, reg;
- int val[] = {0x2004, 0x3000, 0xf800, 0x143f, 0x0000, 0x3000};
+ int val[] = {
+ /*
+ * Values here are chosen based on sniffing USB traffic
+ * under Windows.
+ *
+ * REG0: DAC is master, sample rate 48kHz, no copyright
+ */
+ CM6206_REG0_SPDIFO_RATE_48K |
+ CM6206_REG0_SPDIFO_COPYRIGHT_NA,
+ /*
+ * REG1: PLL binary search enable, soft mute enable.
+ */
+ CM6206_REG1_PLLBIN_EN |
+ CM6206_REG1_SOFT_MUTE_EN |
+ /*
+ * REG2: enable output drivers,
+ * select front channels to the headphone output,
+ * then mute the headphone channels, run the MCU
+ * at 1.5 MHz.
+ */
+ CM6206_REG2_DRIVER_ON |
+ CM6206_REG2_HEADP_SEL_FRONT_CHANNELS |
+ CM6206_REG2_MUTE_HEADPHONE_RIGHT |
+ CM6206_REG2_MUTE_HEADPHONE_LEFT,
+ /*
+ * REG3: default flyspeed, set 2.5V mic bias
+ * enable all line out ports and enable SPDIF
+ */
+ CM6206_REG3_FLYSPEED_DEFAULT |
+ CM6206_REG3_VRAP25EN |
+ CM6206_REG3_FOE |
+ CM6206_REG3_ROE |
+ CM6206_REG3_CBOE |
+ CM6206_REG3_LOSE |
+ CM6206_REG3_HPOE |
+ CM6206_REG3_SPDIFI_CANREC,
+ /* REG4 is just a bunch of GPIO lines */
+ 0x0000,
+ /* REG5: de-assert AD/DA reset signals */
+ CM6206_REG5_DA_RSTN |
+ CM6206_REG5_AD_RSTN };
for (reg = 0; reg < ARRAY_SIZE(val); reg++) {
err = snd_usb_cm106_write_int_reg(dev, reg, val[reg]);
projects / linux-2.6-microblaze.git / blobdiff