* Copyright (C) 2018-2020 Intel Corporation
*/
+#include <linux/ethtool.h>
#include <linux/netdevice.h>
#include <linux/debugfs.h>
#include <linux/list.h>
bool partial;
};
-/**
- * struct ieee80211_he_bss_color - AP settings for BSS coloring
- *
- * @color: the current color.
- * @disabled: is the feature disabled.
- * @partial: define the AID equation.
- */
-struct ieee80211_he_bss_color {
- u8 color;
- bool disabled;
- bool partial;
-};
-
/**
* struct ieee80211_sta_ht_cap - STA's HT capabilities
*
* @sae_pwd: password for SAE authentication (for devices supporting SAE
* offload)
* @sae_pwd_len: length of SAE password (for devices supporting SAE offload)
+ * @sae_pwe: The mechanisms allowed for SAE PWE derivation:
+ *
+ * NL80211_SAE_PWE_UNSPECIFIED
+ * Not-specified, used to indicate userspace did not specify any
+ * preference. The driver should follow its internal policy in
+ * such a scenario.
+ *
+ * NL80211_SAE_PWE_HUNT_AND_PECK
+ * Allow hunting-and-pecking loop only
+ *
+ * NL80211_SAE_PWE_HASH_TO_ELEMENT
+ * Allow hash-to-element only
+ *
+ * NL80211_SAE_PWE_BOTH
+ * Allow either hunting-and-pecking loop or hash-to-element
*/
struct cfg80211_crypto_settings {
u32 wpa_versions;
const u8 *psk;
const u8 *sae_pwd;
u8 sae_pwd_len;
+ enum nl80211_sae_pwe_mechanism sae_pwe;
};
/**
* @vht_required: stations must support VHT
* @twt_responder: Enable Target Wait Time
* @he_required: stations must support HE
+ * @sae_h2e_required: stations must support direct H2E technique in SAE
* @flags: flags, as defined in enum cfg80211_ap_settings_flags
* @he_obss_pd: OBSS Packet Detection settings
* @he_bss_color: BSS Color settings
const struct ieee80211_vht_cap *vht_cap;
const struct ieee80211_he_cap_elem *he_cap;
const struct ieee80211_he_operation *he_oper;
- bool ht_required, vht_required, he_required;
+ bool ht_required, vht_required, he_required, sae_h2e_required;
bool twt_responder;
u32 flags;
struct ieee80211_he_obss_pd he_obss_pd;
u8 connected_to_as;
};
+/**
+ * struct cfg80211_sar_sub_specs - sub specs limit
+ * @power: power limitation in 0.25dbm
+ * @freq_range_index: index the power limitation applies to
+ */
+struct cfg80211_sar_sub_specs {
+ s32 power;
+ u32 freq_range_index;
+};
+
+/**
+ * struct cfg80211_sar_specs - sar limit specs
+ * @type: it's set with power in 0.25dbm or other types
+ * @num_sub_specs: number of sar sub specs
+ * @sub_specs: memory to hold the sar sub specs
+ */
+struct cfg80211_sar_specs {
+ enum nl80211_sar_type type;
+ u32 num_sub_specs;
+ struct cfg80211_sar_sub_specs sub_specs[];
+};
+
+
+/**
+ * @struct cfg80211_sar_chan_ranges - sar frequency ranges
+ * @start_freq: start range edge frequency
+ * @end_freq: end range edge frequency
+ */
+struct cfg80211_sar_freq_ranges {
+ u32 start_freq;
+ u32 end_freq;
+};
+
+/**
+ * struct cfg80211_sar_capa - sar limit capability
+ * @type: it's set via power in 0.25dbm or other types
+ * @num_freq_ranges: number of frequency ranges
+ * @freq_ranges: memory to hold the freq ranges.
+ *
+ * Note: WLAN driver may append new ranges or split an existing
+ * range to small ones and then append them.
+ */
+struct cfg80211_sar_capa {
+ enum nl80211_sar_type type;
+ u32 num_freq_ranges;
+ const struct cfg80211_sar_freq_ranges *freq_ranges;
+};
+
#if IS_ENABLED(CONFIG_CFG80211)
/**
* cfg80211_get_station - retrieve information about a given station
* @get_tx_power: store the current TX power into the dbm variable;
* return 0 if successful
*
- * @set_wds_peer: set the WDS peer for a WDS interface
- *
* @rfkill_poll: polls the hw rfkill line, use cfg80211 reporting
* functions to adjust rfkill hw state
*
int (*get_tx_power)(struct wiphy *wiphy, struct wireless_dev *wdev,
int *dbm);
- int (*set_wds_peer)(struct wiphy *wiphy, struct net_device *dev,
- const u8 *addr);
-
void (*rfkill_poll)(struct wiphy *wiphy);
#ifdef CONFIG_NL80211_TESTMODE
struct cfg80211_tid_config *tid_conf);
int (*reset_tid_config)(struct wiphy *wiphy, struct net_device *dev,
const u8 *peer, u8 tids);
+ int (*set_sar_specs)(struct wiphy *wiphy,
+ struct cfg80211_sar_specs *sar);
};
/*
u8 max_data_retry_count;
+ const struct cfg80211_sar_capa *sar_capa;
+
char priv[] __aligned(NETDEV_ALIGN);
};
* @dev: network device
* @buf: 802.11 frame (header + body)
* @len: length of the frame data
+ * @reconnect: immediate reconnect is desired (include the nl80211 attribute)
*
* This function is called whenever deauthentication has been processed in
* station mode. This includes both received deauthentication frames and
* locally generated ones. This function may sleep. The caller must hold the
* corresponding wdev's mutex.
*/
-void cfg80211_tx_mlme_mgmt(struct net_device *dev, const u8 *buf, size_t len);
+void cfg80211_tx_mlme_mgmt(struct net_device *dev, const u8 *buf, size_t len,
+ bool reconnect);
/**
* cfg80211_rx_unprot_mlme_mgmt - notification of unprotected mlme mgmt frame
* @dev: the device on which the channel switch started
* @chandef: the future channel definition
* @count: the number of TBTTs until the channel switch happens
+ * @quiet: whether or not immediate quiet was requested by the AP
*
* Inform the userspace about the channel switch that has just
* started, so that it can take appropriate actions (eg. starting
*/
void cfg80211_ch_switch_started_notify(struct net_device *dev,
struct cfg80211_chan_def *chandef,
- u8 count);
+ u8 count, bool quiet);
/**
* ieee80211_operating_class_to_band - convert operating class to band
projects / linux-2.6-microblaze.git / blobdiff