#include <asm/io.h>
#include <asm/unaligned.h>
-#include "atmel-mci-regs.h"
+/*
+ * Superset of MCI IP registers integrated in Atmel AVR32 and AT91 Processors
+ * Registers and bitfields marked with [2] are only available in MCI2
+ */
+
+/* MCI Register Definitions */
+#define ATMCI_CR 0x0000 /* Control */
+#define ATMCI_CR_MCIEN BIT(0) /* MCI Enable */
+#define ATMCI_CR_MCIDIS BIT(1) /* MCI Disable */
+#define ATMCI_CR_PWSEN BIT(2) /* Power Save Enable */
+#define ATMCI_CR_PWSDIS BIT(3) /* Power Save Disable */
+#define ATMCI_CR_SWRST BIT(7) /* Software Reset */
+#define ATMCI_MR 0x0004 /* Mode */
+#define ATMCI_MR_CLKDIV(x) ((x) << 0) /* Clock Divider */
+#define ATMCI_MR_PWSDIV(x) ((x) << 8) /* Power Saving Divider */
+#define ATMCI_MR_RDPROOF BIT(11) /* Read Proof */
+#define ATMCI_MR_WRPROOF BIT(12) /* Write Proof */
+#define ATMCI_MR_PDCFBYTE BIT(13) /* Force Byte Transfer */
+#define ATMCI_MR_PDCPADV BIT(14) /* Padding Value */
+#define ATMCI_MR_PDCMODE BIT(15) /* PDC-oriented Mode */
+#define ATMCI_MR_CLKODD(x) ((x) << 16) /* LSB of Clock Divider */
+#define ATMCI_DTOR 0x0008 /* Data Timeout */
+#define ATMCI_DTOCYC(x) ((x) << 0) /* Data Timeout Cycles */
+#define ATMCI_DTOMUL(x) ((x) << 4) /* Data Timeout Multiplier */
+#define ATMCI_SDCR 0x000c /* SD Card / SDIO */
+#define ATMCI_SDCSEL_SLOT_A (0 << 0) /* Select SD slot A */
+#define ATMCI_SDCSEL_SLOT_B (1 << 0) /* Select SD slot A */
+#define ATMCI_SDCSEL_MASK (3 << 0)
+#define ATMCI_SDCBUS_1BIT (0 << 6) /* 1-bit data bus */
+#define ATMCI_SDCBUS_4BIT (2 << 6) /* 4-bit data bus */
+#define ATMCI_SDCBUS_8BIT (3 << 6) /* 8-bit data bus[2] */
+#define ATMCI_SDCBUS_MASK (3 << 6)
+#define ATMCI_ARGR 0x0010 /* Command Argument */
+#define ATMCI_CMDR 0x0014 /* Command */
+#define ATMCI_CMDR_CMDNB(x) ((x) << 0) /* Command Opcode */
+#define ATMCI_CMDR_RSPTYP_NONE (0 << 6) /* No response */
+#define ATMCI_CMDR_RSPTYP_48BIT (1 << 6) /* 48-bit response */
+#define ATMCI_CMDR_RSPTYP_136BIT (2 << 6) /* 136-bit response */
+#define ATMCI_CMDR_SPCMD_INIT (1 << 8) /* Initialization command */
+#define ATMCI_CMDR_SPCMD_SYNC (2 << 8) /* Synchronized command */
+#define ATMCI_CMDR_SPCMD_INT (4 << 8) /* Interrupt command */
+#define ATMCI_CMDR_SPCMD_INTRESP (5 << 8) /* Interrupt response */
+#define ATMCI_CMDR_OPDCMD (1 << 11) /* Open Drain */
+#define ATMCI_CMDR_MAXLAT_5CYC (0 << 12) /* Max latency 5 cycles */
+#define ATMCI_CMDR_MAXLAT_64CYC (1 << 12) /* Max latency 64 cycles */
+#define ATMCI_CMDR_START_XFER (1 << 16) /* Start data transfer */
+#define ATMCI_CMDR_STOP_XFER (2 << 16) /* Stop data transfer */
+#define ATMCI_CMDR_TRDIR_WRITE (0 << 18) /* Write data */
+#define ATMCI_CMDR_TRDIR_READ (1 << 18) /* Read data */
+#define ATMCI_CMDR_BLOCK (0 << 19) /* Single-block transfer */
+#define ATMCI_CMDR_MULTI_BLOCK (1 << 19) /* Multi-block transfer */
+#define ATMCI_CMDR_STREAM (2 << 19) /* MMC Stream transfer */
+#define ATMCI_CMDR_SDIO_BYTE (4 << 19) /* SDIO Byte transfer */
+#define ATMCI_CMDR_SDIO_BLOCK (5 << 19) /* SDIO Block transfer */
+#define ATMCI_CMDR_SDIO_SUSPEND (1 << 24) /* SDIO Suspend Command */
+#define ATMCI_CMDR_SDIO_RESUME (2 << 24) /* SDIO Resume Command */
+#define ATMCI_BLKR 0x0018 /* Block */
+#define ATMCI_BCNT(x) ((x) << 0) /* Data Block Count */
+#define ATMCI_BLKLEN(x) ((x) << 16) /* Data Block Length */
+#define ATMCI_CSTOR 0x001c /* Completion Signal Timeout[2] */
+#define ATMCI_CSTOCYC(x) ((x) << 0) /* CST cycles */
+#define ATMCI_CSTOMUL(x) ((x) << 4) /* CST multiplier */
+#define ATMCI_RSPR 0x0020 /* Response 0 */
+#define ATMCI_RSPR1 0x0024 /* Response 1 */
+#define ATMCI_RSPR2 0x0028 /* Response 2 */
+#define ATMCI_RSPR3 0x002c /* Response 3 */
+#define ATMCI_RDR 0x0030 /* Receive Data */
+#define ATMCI_TDR 0x0034 /* Transmit Data */
+#define ATMCI_SR 0x0040 /* Status */
+#define ATMCI_IER 0x0044 /* Interrupt Enable */
+#define ATMCI_IDR 0x0048 /* Interrupt Disable */
+#define ATMCI_IMR 0x004c /* Interrupt Mask */
+#define ATMCI_CMDRDY BIT(0) /* Command Ready */
+#define ATMCI_RXRDY BIT(1) /* Receiver Ready */
+#define ATMCI_TXRDY BIT(2) /* Transmitter Ready */
+#define ATMCI_BLKE BIT(3) /* Data Block Ended */
+#define ATMCI_DTIP BIT(4) /* Data Transfer In Progress */
+#define ATMCI_NOTBUSY BIT(5) /* Data Not Busy */
+#define ATMCI_ENDRX BIT(6) /* End of RX Buffer */
+#define ATMCI_ENDTX BIT(7) /* End of TX Buffer */
+#define ATMCI_SDIOIRQA BIT(8) /* SDIO IRQ in slot A */
+#define ATMCI_SDIOIRQB BIT(9) /* SDIO IRQ in slot B */
+#define ATMCI_SDIOWAIT BIT(12) /* SDIO Read Wait Operation Status */
+#define ATMCI_CSRCV BIT(13) /* CE-ATA Completion Signal Received */
+#define ATMCI_RXBUFF BIT(14) /* RX Buffer Full */
+#define ATMCI_TXBUFE BIT(15) /* TX Buffer Empty */
+#define ATMCI_RINDE BIT(16) /* Response Index Error */
+#define ATMCI_RDIRE BIT(17) /* Response Direction Error */
+#define ATMCI_RCRCE BIT(18) /* Response CRC Error */
+#define ATMCI_RENDE BIT(19) /* Response End Bit Error */
+#define ATMCI_RTOE BIT(20) /* Response Time-Out Error */
+#define ATMCI_DCRCE BIT(21) /* Data CRC Error */
+#define ATMCI_DTOE BIT(22) /* Data Time-Out Error */
+#define ATMCI_CSTOE BIT(23) /* Completion Signal Time-out Error */
+#define ATMCI_BLKOVRE BIT(24) /* DMA Block Overrun Error */
+#define ATMCI_DMADONE BIT(25) /* DMA Transfer Done */
+#define ATMCI_FIFOEMPTY BIT(26) /* FIFO Empty Flag */
+#define ATMCI_XFRDONE BIT(27) /* Transfer Done Flag */
+#define ATMCI_ACKRCV BIT(28) /* Boot Operation Acknowledge Received */
+#define ATMCI_ACKRCVE BIT(29) /* Boot Operation Acknowledge Error */
+#define ATMCI_OVRE BIT(30) /* RX Overrun Error */
+#define ATMCI_UNRE BIT(31) /* TX Underrun Error */
+#define ATMCI_DMA 0x0050 /* DMA Configuration[2] */
+#define ATMCI_DMA_OFFSET(x) ((x) << 0) /* DMA Write Buffer Offset */
+#define ATMCI_DMA_CHKSIZE(x) ((x) << 4) /* DMA Channel Read and Write Chunk Size */
+#define ATMCI_DMAEN BIT(8) /* DMA Hardware Handshaking Enable */
+#define ATMCI_CFG 0x0054 /* Configuration[2] */
+#define ATMCI_CFG_FIFOMODE_1DATA BIT(0) /* MCI Internal FIFO control mode */
+#define ATMCI_CFG_FERRCTRL_COR BIT(4) /* Flow Error flag reset control mode */
+#define ATMCI_CFG_HSMODE BIT(8) /* High Speed Mode */
+#define ATMCI_CFG_LSYNC BIT(12) /* Synchronize on the last block */
+#define ATMCI_WPMR 0x00e4 /* Write Protection Mode[2] */
+#define ATMCI_WP_EN BIT(0) /* WP Enable */
+#define ATMCI_WP_KEY (0x4d4349 << 8) /* WP Key */
+#define ATMCI_WPSR 0x00e8 /* Write Protection Status[2] */
+#define ATMCI_GET_WP_VS(x) ((x) & 0x0f)
+#define ATMCI_GET_WP_VSRC(x) (((x) >> 8) & 0xffff)
+#define ATMCI_VERSION 0x00FC /* Version */
+#define ATMCI_FIFO_APERTURE 0x0200 /* FIFO Aperture[2] */
+
+/* This is not including the FIFO Aperture on MCI2 */
+#define ATMCI_REGS_SIZE 0x100
+
+/* Register access macros */
+#define atmci_readl(port, reg) \
+ __raw_readl((port)->regs + reg)
+#define atmci_writel(port, reg, value) \
+ __raw_writel((value), (port)->regs + reg)
+
+/* On AVR chips the Peripheral DMA Controller is not connected to MCI. */
+#ifdef CONFIG_AVR32
+# define ATMCI_PDC_CONNECTED 0
+#else
+# define ATMCI_PDC_CONNECTED 1
+#endif
#define AUTOSUSPEND_DELAY 50
return atmci_readl(host, ATMCI_VERSION) & 0x00000fff;
}
+/*
+ * Fix sconfig's burst size according to atmel MCI. We need to convert them as:
+ * 1 -> 0, 4 -> 1, 8 -> 2, 16 -> 3.
+ * With version 0x600, we need to convert them as: 1 -> 0, 2 -> 1, 4 -> 2,
+ * 8 -> 3, 16 -> 4.
+ *
+ * This can be done by finding most significant bit set.
+ */
+static inline unsigned int atmci_convert_chksize(struct atmel_mci *host,
+ unsigned int maxburst)
+{
+ unsigned int version = atmci_get_version(host);
+ unsigned int offset = 2;
+
+ if (version >= 0x600)
+ offset = 1;
+
+ if (maxburst > 1)
+ return fls(maxburst) - offset;
+ else
+ return 0;
+}
+
static void atmci_timeout_timer(unsigned long data)
{
struct atmel_mci *host;
if (data->flags & MMC_DATA_READ) {
direction = DMA_FROM_DEVICE;
host->dma_conf.direction = slave_dirn = DMA_DEV_TO_MEM;
- maxburst = atmci_convert_chksize(host->dma_conf.src_maxburst);
+ maxburst = atmci_convert_chksize(host,
+ host->dma_conf.src_maxburst);
} else {
direction = DMA_TO_DEVICE;
host->dma_conf.direction = slave_dirn = DMA_MEM_TO_DEV;
- maxburst = atmci_convert_chksize(host->dma_conf.dst_maxburst);
+ maxburst = atmci_convert_chksize(host,
+ host->dma_conf.dst_maxburst);
}
if (host->caps.has_dma_conf_reg)
projects / linux-2.6-microblaze.git / blobdiff