+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 1995-2000 Linus Torvalds & author (see below)
- */
-
-/*
- * HT-6560B EIDE-controller support
- * To activate controller support use kernel parameter "ide0=ht6560b".
- * Use hdparm utility to enable PIO mode support.
- *
- * Author: Mikko Ala-Fossi <maf@iki.fi>
- * Jan Evert van Grootheest <j.e.van.grootheest@caiway.nl>
- *
- */
-
-#define DRV_NAME "ht6560b"
-#define HT6560B_VERSION "v0.08"
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/ioport.h>
-#include <linux/blkdev.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-
-#include <asm/io.h>
-
-/* #define DEBUG */ /* remove comments for DEBUG messages */
-
-/*
- * The special i/o-port that HT-6560B uses to configuration:
- * bit0 (0x01): "1" selects secondary interface
- * bit2 (0x04): "1" enables FIFO function
- * bit5 (0x20): "1" enables prefetched data read function (???)
- *
- * The special i/o-port that HT-6560A uses to configuration:
- * bit0 (0x01): "1" selects secondary interface
- * bit1 (0x02): "1" enables prefetched data read function
- * bit2 (0x04): "0" enables multi-master system (?)
- * bit3 (0x08): "1" 3 cycle time, "0" 2 cycle time (?)
- */
-#define HT_CONFIG_PORT 0x3e6
-
-static inline u8 HT_CONFIG(ide_drive_t *drive)
-{
- return ((unsigned long)ide_get_drivedata(drive) & 0xff00) >> 8;
-}
-
-/*
- * FIFO + PREFETCH (both a/b-model)
- */
-#define HT_CONFIG_DEFAULT 0x1c /* no prefetch */
-/* #define HT_CONFIG_DEFAULT 0x3c */ /* with prefetch */
-#define HT_SECONDARY_IF 0x01
-#define HT_PREFETCH_MODE 0x20
-
-/*
- * ht6560b Timing values:
- *
- * I reviewed some assembler source listings of htide drivers and found
- * out how they setup those cycle time interfacing values, as they at Holtek
- * call them. IDESETUP.COM that is supplied with the drivers figures out
- * optimal values and fetches those values to drivers. I found out that
- * they use Select register to fetch timings to the ide board right after
- * interface switching. After that it was quite easy to add code to
- * ht6560b.c.
- *
- * IDESETUP.COM gave me values 0x24, 0x45, 0xaa, 0xff that worked fine
- * for hda and hdc. But hdb needed higher values to work, so I guess
- * that sometimes it is necessary to give higher value than IDESETUP
- * gives. [see cmd640.c for an extreme example of this. -ml]
- *
- * Perhaps I should explain something about these timing values:
- * The higher nibble of value is the Recovery Time (rt) and the lower nibble
- * of the value is the Active Time (at). Minimum value 2 is the fastest and
- * the maximum value 15 is the slowest. Default values should be 15 for both.
- * So 0x24 means 2 for rt and 4 for at. Each of the drives should have
- * both values, and IDESETUP gives automatically rt=15 st=15 for CDROMs or
- * similar. If value is too small there will be all sorts of failures.
- *
- * Timing byte consists of
- * High nibble: Recovery Cycle Time (rt)
- * The valid values range from 2 to 15. The default is 15.
- *
- * Low nibble: Active Cycle Time (at)
- * The valid values range from 2 to 15. The default is 15.
- *
- * You can obtain optimized timing values by running Holtek IDESETUP.COM
- * for DOS. DOS drivers get their timing values from command line, where
- * the first value is the Recovery Time and the second value is the
- * Active Time for each drive. Smaller value gives higher speed.
- * In case of failures you should probably fall back to a higher value.
- */
-static inline u8 HT_TIMING(ide_drive_t *drive)
-{
- return (unsigned long)ide_get_drivedata(drive) & 0x00ff;
-}
-
-#define HT_TIMING_DEFAULT 0xff
-
-/*
- * This routine handles interface switching for the peculiar hardware design
- * on the F.G.I./Holtek HT-6560B VLB IDE interface.
- * The HT-6560B can only enable one IDE port at a time, and requires a
- * silly sequence (below) whenever we switch between primary and secondary.
- */
-
-/*
- * This routine is invoked from ide.c to prepare for access to a given drive.
- */
-static void ht6560b_dev_select(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- unsigned long flags;
- static u8 current_select = 0;
- static u8 current_timing = 0;
- u8 select, timing;
-
- local_irq_save(flags);
-
- select = HT_CONFIG(drive);
- timing = HT_TIMING(drive);
-
- /*
- * Need to enforce prefetch sometimes because otherwise
- * it'll hang (hard).
- */
- if (drive->media != ide_disk ||
- (drive->dev_flags & IDE_DFLAG_PRESENT) == 0)
- select |= HT_PREFETCH_MODE;
-
- if (select != current_select || timing != current_timing) {
- current_select = select;
- current_timing = timing;
- (void)inb(HT_CONFIG_PORT);
- (void)inb(HT_CONFIG_PORT);
- (void)inb(HT_CONFIG_PORT);
- (void)inb(HT_CONFIG_PORT);
- outb(select, HT_CONFIG_PORT);
- /*
- * Set timing for this drive:
- */
- outb(timing, hwif->io_ports.device_addr);
- (void)inb(hwif->io_ports.status_addr);
-#ifdef DEBUG
- printk("ht6560b: %s: select=%#x timing=%#x\n",
- drive->name, select, timing);
-#endif
- }
- local_irq_restore(flags);
-
- outb(drive->select | ATA_DEVICE_OBS, hwif->io_ports.device_addr);
-}
-
-/*
- * Autodetection and initialization of ht6560b
- */
-static int __init try_to_init_ht6560b(void)
-{
- u8 orig_value;
- int i;
-
- /* Autodetect ht6560b */
- if ((orig_value = inb(HT_CONFIG_PORT)) == 0xff)
- return 0;
-
- for (i=3;i>0;i--) {
- outb(0x00, HT_CONFIG_PORT);
- if (!( (~inb(HT_CONFIG_PORT)) & 0x3f )) {
- outb(orig_value, HT_CONFIG_PORT);
- return 0;
- }
- }
- outb(0x00, HT_CONFIG_PORT);
- if ((~inb(HT_CONFIG_PORT))& 0x3f) {
- outb(orig_value, HT_CONFIG_PORT);
- return 0;
- }
- /*
- * Ht6560b autodetected
- */
- outb(HT_CONFIG_DEFAULT, HT_CONFIG_PORT);
- outb(HT_TIMING_DEFAULT, 0x1f6); /* Select register */
- (void)inb(0x1f7); /* Status register */
-
- printk("ht6560b " HT6560B_VERSION
- ": chipset detected and initialized"
-#ifdef DEBUG
- " with debug enabled"
-#endif
- "\n"
- );
- return 1;
-}
-
-static u8 ht_pio2timings(ide_drive_t *drive, const u8 pio)
-{
- int active_time, recovery_time;
- int active_cycles, recovery_cycles;
- int bus_speed = ide_vlb_clk ? ide_vlb_clk : 50;
-
- if (pio) {
- unsigned int cycle_time;
- struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
-
- cycle_time = ide_pio_cycle_time(drive, pio);
-
- /*
- * Just like opti621.c we try to calculate the
- * actual cycle time for recovery and activity
- * according system bus speed.
- */
- active_time = t->active;
- recovery_time = cycle_time - active_time - t->setup;
- /*
- * Cycle times should be Vesa bus cycles
- */
- active_cycles = (active_time * bus_speed + 999) / 1000;
- recovery_cycles = (recovery_time * bus_speed + 999) / 1000;
- /*
- * Upper and lower limits
- */
- if (active_cycles < 2) active_cycles = 2;
- if (recovery_cycles < 2) recovery_cycles = 2;
- if (active_cycles > 15) active_cycles = 15;
- if (recovery_cycles > 15) recovery_cycles = 0; /* 0==16 */
-
-#ifdef DEBUG
- printk("ht6560b: drive %s setting pio=%d recovery=%d (%dns) active=%d (%dns)\n", drive->name, pio, recovery_cycles, recovery_time, active_cycles, active_time);
-#endif
-
- return (u8)((recovery_cycles << 4) | active_cycles);
- } else {
-
-#ifdef DEBUG
- printk("ht6560b: drive %s setting pio=0\n", drive->name);
-#endif
-
- return HT_TIMING_DEFAULT; /* default setting */
- }
-}
-
-static DEFINE_SPINLOCK(ht6560b_lock);
-
-/*
- * Enable/Disable so called prefetch mode
- */
-static void ht_set_prefetch(ide_drive_t *drive, u8 state)
-{
- unsigned long flags, config;
- int t = HT_PREFETCH_MODE << 8;
-
- spin_lock_irqsave(&ht6560b_lock, flags);
-
- config = (unsigned long)ide_get_drivedata(drive);
-
- /*
- * Prefetch mode and unmask irq seems to conflict
- */
- if (state) {
- config |= t; /* enable prefetch mode */
- drive->dev_flags |= IDE_DFLAG_NO_UNMASK;
- drive->dev_flags &= ~IDE_DFLAG_UNMASK;
- } else {
- config &= ~t; /* disable prefetch mode */
- drive->dev_flags &= ~IDE_DFLAG_NO_UNMASK;
- }
-
- ide_set_drivedata(drive, (void *)config);
-
- spin_unlock_irqrestore(&ht6560b_lock, flags);
-
-#ifdef DEBUG
- printk("ht6560b: drive %s prefetch mode %sabled\n", drive->name, (state ? "en" : "dis"));
-#endif
-}
-
-static void ht6560b_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- unsigned long flags, config;
- const u8 pio = drive->pio_mode - XFER_PIO_0;
- u8 timing;
-
- switch (pio) {
- case 8: /* set prefetch off */
- case 9: /* set prefetch on */
- ht_set_prefetch(drive, pio & 1);
- return;
- }
-
- timing = ht_pio2timings(drive, pio);
-
- spin_lock_irqsave(&ht6560b_lock, flags);
- config = (unsigned long)ide_get_drivedata(drive);
- config &= 0xff00;
- config |= timing;
- ide_set_drivedata(drive, (void *)config);
- spin_unlock_irqrestore(&ht6560b_lock, flags);
-
-#ifdef DEBUG
- printk("ht6560b: drive %s tuned to pio mode %#x timing=%#x\n", drive->name, pio, timing);
-#endif
-}
-
-static void __init ht6560b_init_dev(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- /* Setting default configurations for drives. */
- unsigned long t = (HT_CONFIG_DEFAULT << 8) | HT_TIMING_DEFAULT;
-
- if (hwif->channel)
- t |= (HT_SECONDARY_IF << 8);
-
- ide_set_drivedata(drive, (void *)t);
-}
-
-static bool probe_ht6560b;
-
-module_param_named(probe, probe_ht6560b, bool, 0);
-MODULE_PARM_DESC(probe, "probe for HT6560B chipset");
-
-static const struct ide_tp_ops ht6560b_tp_ops = {
- .exec_command = ide_exec_command,
- .read_status = ide_read_status,
- .read_altstatus = ide_read_altstatus,
- .write_devctl = ide_write_devctl,
-
- .dev_select = ht6560b_dev_select,
- .tf_load = ide_tf_load,
- .tf_read = ide_tf_read,
-
- .input_data = ide_input_data,
- .output_data = ide_output_data,
-};
-
-static const struct ide_port_ops ht6560b_port_ops = {
- .init_dev = ht6560b_init_dev,
- .set_pio_mode = ht6560b_set_pio_mode,
-};
-
-static const struct ide_port_info ht6560b_port_info __initconst = {
- .name = DRV_NAME,
- .chipset = ide_ht6560b,
- .tp_ops = &ht6560b_tp_ops,
- .port_ops = &ht6560b_port_ops,
- .host_flags = IDE_HFLAG_SERIALIZE | /* is this needed? */
- IDE_HFLAG_NO_DMA |
- IDE_HFLAG_ABUSE_PREFETCH,
- .pio_mask = ATA_PIO4,
-};
-
-static int __init ht6560b_init(void)
-{
- if (probe_ht6560b == 0)
- return -ENODEV;
-
- if (!request_region(HT_CONFIG_PORT, 1, DRV_NAME)) {
- printk(KERN_NOTICE "%s: HT_CONFIG_PORT not found\n",
- __func__);
- return -ENODEV;
- }
-
- if (!try_to_init_ht6560b()) {
- printk(KERN_NOTICE "%s: HBA not found\n", __func__);
- goto release_region;
- }
-
- return ide_legacy_device_add(&ht6560b_port_info, 0);
-
-release_region:
- release_region(HT_CONFIG_PORT, 1);
- return -ENODEV;
-}
-
-module_init(ht6560b_init);
-
-MODULE_AUTHOR("See Local File");
-MODULE_DESCRIPTION("HT-6560B EIDE-controller support");
-MODULE_LICENSE("GPL");
projects / linux-2.6-microblaze.git / blobdiff