/* Wait for the Pipe State to go off */
if (wait_for((I915_READ(reg) & I965_PIPECONF_ACTIVE) == 0,
100))
- DRM_DEBUG_KMS("pipe_off wait timed out\n");
+ WARN(1, "pipe_off wait timed out\n");
} else {
u32 last_line, line_mask;
int reg = PIPEDSL(pipe);
} while (((I915_READ(reg) & line_mask) != last_line) &&
time_after(timeout, jiffies));
if (time_after(jiffies, timeout))
- DRM_DEBUG_KMS("pipe_off wait timed out\n");
+ WARN(1, "pipe_off wait timed out\n");
}
}
* protect mechanism may be enabled.
*
* Note! This is for pre-ILK only.
+ *
+ * Unfortunately needed by dvo_ns2501 since the dvo depends on it running.
*/
static void intel_enable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)
{
intel_wait_for_vblank(dev_priv->dev, pipe);
}
-static void disable_pch_dp(struct drm_i915_private *dev_priv,
- enum pipe pipe, int reg, u32 port_sel)
-{
- u32 val = I915_READ(reg);
- if (dp_pipe_enabled(dev_priv, pipe, port_sel, val)) {
- DRM_DEBUG_KMS("Disabling pch dp %x on pipe %d\n", reg, pipe);
- I915_WRITE(reg, val & ~DP_PORT_EN);
- }
-}
-
-static void disable_pch_hdmi(struct drm_i915_private *dev_priv,
- enum pipe pipe, int reg)
-{
- u32 val = I915_READ(reg);
- if (hdmi_pipe_enabled(dev_priv, pipe, val)) {
- DRM_DEBUG_KMS("Disabling pch HDMI %x on pipe %d\n",
- reg, pipe);
- I915_WRITE(reg, val & ~PORT_ENABLE);
- }
-}
-
-/* Disable any ports connected to this transcoder */
-static void intel_disable_pch_ports(struct drm_i915_private *dev_priv,
- enum pipe pipe)
-{
- u32 reg, val;
-
- val = I915_READ(PCH_PP_CONTROL);
- I915_WRITE(PCH_PP_CONTROL, val | PANEL_UNLOCK_REGS);
-
- disable_pch_dp(dev_priv, pipe, PCH_DP_B, TRANS_DP_PORT_SEL_B);
- disable_pch_dp(dev_priv, pipe, PCH_DP_C, TRANS_DP_PORT_SEL_C);
- disable_pch_dp(dev_priv, pipe, PCH_DP_D, TRANS_DP_PORT_SEL_D);
-
- reg = PCH_ADPA;
- val = I915_READ(reg);
- if (adpa_pipe_enabled(dev_priv, pipe, val))
- I915_WRITE(reg, val & ~ADPA_DAC_ENABLE);
-
- reg = PCH_LVDS;
- val = I915_READ(reg);
- if (lvds_pipe_enabled(dev_priv, pipe, val)) {
- DRM_DEBUG_KMS("disable lvds on pipe %d val 0x%08x\n", pipe, val);
- I915_WRITE(reg, val & ~LVDS_PORT_EN);
- POSTING_READ(reg);
- udelay(100);
- }
-
- disable_pch_hdmi(dev_priv, pipe, HDMIB);
- disable_pch_hdmi(dev_priv, pipe, HDMIC);
- disable_pch_hdmi(dev_priv, pipe, HDMID);
-}
-
int
intel_pin_and_fence_fb_obj(struct drm_device *dev,
struct drm_i915_gem_object *obj,
static int
intel_pipe_set_base(struct drm_crtc *crtc, int x, int y,
- struct drm_framebuffer *old_fb)
+ struct drm_framebuffer *fb)
{
struct drm_device *dev = crtc->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
struct drm_i915_master_private *master_priv;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ struct drm_framebuffer *old_fb;
int ret;
/* no fb bound */
- if (!crtc->fb) {
+ if (!fb) {
DRM_ERROR("No FB bound\n");
return 0;
}
mutex_lock(&dev->struct_mutex);
ret = intel_pin_and_fence_fb_obj(dev,
- to_intel_framebuffer(crtc->fb)->obj,
+ to_intel_framebuffer(fb)->obj,
NULL);
if (ret != 0) {
mutex_unlock(&dev->struct_mutex);
return ret;
}
- if (old_fb)
- intel_finish_fb(old_fb);
+ if (crtc->fb)
+ intel_finish_fb(crtc->fb);
- ret = dev_priv->display.update_plane(crtc, crtc->fb, x, y);
+ ret = dev_priv->display.update_plane(crtc, fb, x, y);
if (ret) {
- intel_unpin_fb_obj(to_intel_framebuffer(crtc->fb)->obj);
+ intel_unpin_fb_obj(to_intel_framebuffer(fb)->obj);
mutex_unlock(&dev->struct_mutex);
DRM_ERROR("failed to update base address\n");
return ret;
}
+ old_fb = crtc->fb;
+ crtc->fb = fb;
+ crtc->x = x;
+ crtc->y = y;
+
if (old_fb) {
intel_wait_for_vblank(dev, intel_crtc->pipe);
intel_unpin_fb_obj(to_intel_framebuffer(old_fb)->obj);
DRM_DEBUG_KMS("FDI train done.\n");
}
-static void ironlake_fdi_pll_enable(struct drm_crtc *crtc)
+static void ironlake_fdi_pll_enable(struct intel_crtc *intel_crtc)
{
- struct drm_device *dev = crtc->dev;
+ struct drm_device *dev = intel_crtc->base.dev;
struct drm_i915_private *dev_priv = dev->dev_private;
- struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
int pipe = intel_crtc->pipe;
u32 reg, temp;
}
}
+static void ironlake_fdi_pll_disable(struct intel_crtc *intel_crtc)
+{
+ struct drm_device *dev = intel_crtc->base.dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ int pipe = intel_crtc->pipe;
+ u32 reg, temp;
+
+ /* Switch from PCDclk to Rawclk */
+ reg = FDI_RX_CTL(pipe);
+ temp = I915_READ(reg);
+ I915_WRITE(reg, temp & ~FDI_PCDCLK);
+
+ /* Disable CPU FDI TX PLL */
+ reg = FDI_TX_CTL(pipe);
+ temp = I915_READ(reg);
+ I915_WRITE(reg, temp & ~FDI_TX_PLL_ENABLE);
+
+ POSTING_READ(reg);
+ udelay(100);
+
+ reg = FDI_RX_CTL(pipe);
+ temp = I915_READ(reg);
+ I915_WRITE(reg, temp & ~FDI_RX_PLL_ENABLE);
+
+ /* Wait for the clocks to turn off. */
+ POSTING_READ(reg);
+ udelay(100);
+}
+
static void cpt_phase_pointer_disable(struct drm_device *dev, int pipe)
{
struct drm_i915_private *dev_priv = dev->dev_private;
static bool intel_crtc_driving_pch(struct drm_crtc *crtc)
{
struct drm_device *dev = crtc->dev;
- struct intel_encoder *encoder;
+ struct intel_encoder *intel_encoder;
/*
* If there's a non-PCH eDP on this crtc, it must be DP_A, and that
* must be driven by its own crtc; no sharing is possible.
*/
- for_each_encoder_on_crtc(dev, crtc, encoder) {
+ for_each_encoder_on_crtc(dev, crtc, intel_encoder) {
/* On Haswell, LPT PCH handles the VGA connection via FDI, and Haswell
* CPU handles all others */
/* It is still unclear how this will work on PPT, so throw up a warning */
WARN_ON(!HAS_PCH_LPT(dev));
- if (encoder->type == DRM_MODE_ENCODER_DAC) {
+ if (intel_encoder->type == INTEL_OUTPUT_ANALOG) {
DRM_DEBUG_KMS("Haswell detected DAC encoder, assuming is PCH\n");
return true;
} else {
DRM_DEBUG_KMS("Haswell detected encoder %d, assuming is CPU\n",
- encoder->type);
+ intel_encoder->type);
return false;
}
}
- switch (encoder->type) {
+ switch (intel_encoder->type) {
case INTEL_OUTPUT_EDP:
- if (!intel_encoder_is_pch_edp(&encoder->base))
+ if (!intel_encoder_is_pch_edp(&intel_encoder->base))
return false;
continue;
}
struct drm_device *dev = crtc->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ struct intel_encoder *encoder;
int pipe = intel_crtc->pipe;
int plane = intel_crtc->plane;
u32 temp;
bool is_pch_port;
+ WARN_ON(!crtc->enabled);
+
if (intel_crtc->active)
return;
is_pch_port = intel_crtc_driving_pch(crtc);
- if (is_pch_port)
- ironlake_fdi_pll_enable(crtc);
- else
- ironlake_fdi_disable(crtc);
+ if (is_pch_port) {
+ ironlake_fdi_pll_enable(intel_crtc);
+ } else {
+ assert_fdi_tx_disabled(dev_priv, pipe);
+ assert_fdi_rx_disabled(dev_priv, pipe);
+ }
+
+ for_each_encoder_on_crtc(dev, crtc, encoder)
+ if (encoder->pre_enable)
+ encoder->pre_enable(encoder);
/* Enable panel fitting for LVDS */
if (dev_priv->pch_pf_size &&
mutex_unlock(&dev->struct_mutex);
intel_crtc_update_cursor(crtc, true);
+
+ for_each_encoder_on_crtc(dev, crtc, encoder)
+ encoder->enable(encoder);
+
+ if (HAS_PCH_CPT(dev))
+ intel_cpt_verify_modeset(dev, intel_crtc->pipe);
}
static void ironlake_crtc_disable(struct drm_crtc *crtc)
struct drm_device *dev = crtc->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ struct intel_encoder *encoder;
int pipe = intel_crtc->pipe;
int plane = intel_crtc->plane;
u32 reg, temp;
+
if (!intel_crtc->active)
return;
+ for_each_encoder_on_crtc(dev, crtc, encoder)
+ encoder->disable(encoder);
+
intel_crtc_wait_for_pending_flips(crtc);
drm_vblank_off(dev, pipe);
intel_crtc_update_cursor(crtc, false);
I915_WRITE(PF_CTL(pipe), 0);
I915_WRITE(PF_WIN_SZ(pipe), 0);
- ironlake_fdi_disable(crtc);
+ for_each_encoder_on_crtc(dev, crtc, encoder)
+ if (encoder->post_disable)
+ encoder->post_disable(encoder);
- /* This is a horrible layering violation; we should be doing this in
- * the connector/encoder ->prepare instead, but we don't always have
- * enough information there about the config to know whether it will
- * actually be necessary or just cause undesired flicker.
- */
- intel_disable_pch_ports(dev_priv, pipe);
+ ironlake_fdi_disable(crtc);
intel_disable_transcoder(dev_priv, pipe);
/* disable PCH DPLL */
intel_disable_pch_pll(intel_crtc);
- /* Switch from PCDclk to Rawclk */
- reg = FDI_RX_CTL(pipe);
- temp = I915_READ(reg);
- I915_WRITE(reg, temp & ~FDI_PCDCLK);
-
- /* Disable CPU FDI TX PLL */
- reg = FDI_TX_CTL(pipe);
- temp = I915_READ(reg);
- I915_WRITE(reg, temp & ~FDI_TX_PLL_ENABLE);
-
- POSTING_READ(reg);
- udelay(100);
-
- reg = FDI_RX_CTL(pipe);
- temp = I915_READ(reg);
- I915_WRITE(reg, temp & ~FDI_RX_PLL_ENABLE);
-
- /* Wait for the clocks to turn off. */
- POSTING_READ(reg);
- udelay(100);
+ ironlake_fdi_pll_disable(intel_crtc);
intel_crtc->active = false;
intel_update_watermarks(dev);
mutex_unlock(&dev->struct_mutex);
}
-static void ironlake_crtc_dpms(struct drm_crtc *crtc, int mode)
-{
- struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
- int pipe = intel_crtc->pipe;
- int plane = intel_crtc->plane;
-
- /* XXX: When our outputs are all unaware of DPMS modes other than off
- * and on, we should map those modes to DRM_MODE_DPMS_OFF in the CRTC.
- */
- switch (mode) {
- case DRM_MODE_DPMS_ON:
- case DRM_MODE_DPMS_STANDBY:
- case DRM_MODE_DPMS_SUSPEND:
- DRM_DEBUG_KMS("crtc %d/%d dpms on\n", pipe, plane);
- ironlake_crtc_enable(crtc);
- break;
-
- case DRM_MODE_DPMS_OFF:
- DRM_DEBUG_KMS("crtc %d/%d dpms off\n", pipe, plane);
- ironlake_crtc_disable(crtc);
- break;
- }
-}
-
static void ironlake_crtc_off(struct drm_crtc *crtc)
{
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
struct drm_device *dev = crtc->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ struct intel_encoder *encoder;
int pipe = intel_crtc->pipe;
int plane = intel_crtc->plane;
+ WARN_ON(!crtc->enabled);
+
if (intel_crtc->active)
return;
/* Give the overlay scaler a chance to enable if it's on this pipe */
intel_crtc_dpms_overlay(intel_crtc, true);
intel_crtc_update_cursor(crtc, true);
+
+ for_each_encoder_on_crtc(dev, crtc, encoder)
+ encoder->enable(encoder);
}
static void i9xx_crtc_disable(struct drm_crtc *crtc)
struct drm_device *dev = crtc->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ struct intel_encoder *encoder;
int pipe = intel_crtc->pipe;
int plane = intel_crtc->plane;
+
if (!intel_crtc->active)
return;
+ for_each_encoder_on_crtc(dev, crtc, encoder)
+ encoder->disable(encoder);
+
/* Give the overlay scaler a chance to disable if it's on this pipe */
intel_crtc_wait_for_pending_flips(crtc);
drm_vblank_off(dev, pipe);
intel_update_watermarks(dev);
}
-static void i9xx_crtc_dpms(struct drm_crtc *crtc, int mode)
-{
- /* XXX: When our outputs are all unaware of DPMS modes other than off
- * and on, we should map those modes to DRM_MODE_DPMS_OFF in the CRTC.
- */
- switch (mode) {
- case DRM_MODE_DPMS_ON:
- case DRM_MODE_DPMS_STANDBY:
- case DRM_MODE_DPMS_SUSPEND:
- i9xx_crtc_enable(crtc);
- break;
- case DRM_MODE_DPMS_OFF:
- i9xx_crtc_disable(crtc);
- break;
- }
-}
-
static void i9xx_crtc_off(struct drm_crtc *crtc)
{
}
-/**
- * Sets the power management mode of the pipe and plane.
- */
-static void intel_crtc_dpms(struct drm_crtc *crtc, int mode)
+static void intel_crtc_update_sarea(struct drm_crtc *crtc,
+ bool enabled)
{
struct drm_device *dev = crtc->dev;
- struct drm_i915_private *dev_priv = dev->dev_private;
struct drm_i915_master_private *master_priv;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
int pipe = intel_crtc->pipe;
- bool enabled;
-
- if (intel_crtc->dpms_mode == mode)
- return;
-
- intel_crtc->dpms_mode = mode;
-
- dev_priv->display.dpms(crtc, mode);
if (!dev->primary->master)
return;
if (!master_priv->sarea_priv)
return;
- enabled = crtc->enabled && mode != DRM_MODE_DPMS_OFF;
-
switch (pipe) {
case 0:
master_priv->sarea_priv->pipeA_w = enabled ? crtc->mode.hdisplay : 0;
}
}
+/**
+ * Sets the power management mode of the pipe and plane.
+ */
+void intel_crtc_update_dpms(struct drm_crtc *crtc)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_encoder *intel_encoder;
+ bool enable = false;
+
+ for_each_encoder_on_crtc(dev, crtc, intel_encoder)
+ enable |= intel_encoder->connectors_active;
+
+ if (enable)
+ dev_priv->display.crtc_enable(crtc);
+ else
+ dev_priv->display.crtc_disable(crtc);
+
+ intel_crtc_update_sarea(crtc, enable);
+}
+
+static void intel_crtc_noop(struct drm_crtc *crtc)
+{
+}
+
static void intel_crtc_disable(struct drm_crtc *crtc)
{
- struct drm_crtc_helper_funcs *crtc_funcs = crtc->helper_private;
struct drm_device *dev = crtc->dev;
+ struct drm_connector *connector;
struct drm_i915_private *dev_priv = dev->dev_private;
- crtc_funcs->dpms(crtc, DRM_MODE_DPMS_OFF);
+ /* crtc should still be enabled when we disable it. */
+ WARN_ON(!crtc->enabled);
+
+ dev_priv->display.crtc_disable(crtc);
+ intel_crtc_update_sarea(crtc, false);
dev_priv->display.off(crtc);
assert_plane_disabled(dev->dev_private, to_intel_crtc(crtc)->plane);
mutex_lock(&dev->struct_mutex);
intel_unpin_fb_obj(to_intel_framebuffer(crtc->fb)->obj);
mutex_unlock(&dev->struct_mutex);
+ crtc->fb = NULL;
+ }
+
+ /* Update computed state. */
+ list_for_each_entry(connector, &dev->mode_config.connector_list, head) {
+ if (!connector->encoder || !connector->encoder->crtc)
+ continue;
+
+ if (connector->encoder->crtc != crtc)
+ continue;
+
+ connector->dpms = DRM_MODE_DPMS_OFF;
+ to_intel_encoder(connector->encoder)->connectors_active = false;
}
}
-/* Prepare for a mode set.
- *
- * Note we could be a lot smarter here. We need to figure out which outputs
- * will be enabled, which disabled (in short, how the config will changes)
- * and perform the minimum necessary steps to accomplish that, e.g. updating
- * watermarks, FBC configuration, making sure PLLs are programmed correctly,
- * panel fitting is in the proper state, etc.
- */
-static void i9xx_crtc_prepare(struct drm_crtc *crtc)
+void intel_modeset_disable(struct drm_device *dev)
{
- i9xx_crtc_disable(crtc);
+ struct drm_crtc *crtc;
+
+ list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
+ if (crtc->enabled)
+ intel_crtc_disable(crtc);
+ }
}
-static void i9xx_crtc_commit(struct drm_crtc *crtc)
+void intel_encoder_noop(struct drm_encoder *encoder)
{
- i9xx_crtc_enable(crtc);
}
-static void ironlake_crtc_prepare(struct drm_crtc *crtc)
+void intel_encoder_destroy(struct drm_encoder *encoder)
{
- ironlake_crtc_disable(crtc);
+ struct intel_encoder *intel_encoder = to_intel_encoder(encoder);
+
+ drm_encoder_cleanup(encoder);
+ kfree(intel_encoder);
}
-static void ironlake_crtc_commit(struct drm_crtc *crtc)
+/* Simple dpms helper for encodres with just one connector, no cloning and only
+ * one kind of off state. It clamps all !ON modes to fully OFF and changes the
+ * state of the entire output pipe. */
+void intel_encoder_dpms(struct intel_encoder *encoder, int mode)
{
- ironlake_crtc_enable(crtc);
+ if (mode == DRM_MODE_DPMS_ON) {
+ encoder->connectors_active = true;
+
+ intel_crtc_update_dpms(encoder->base.crtc);
+ } else {
+ encoder->connectors_active = false;
+
+ intel_crtc_update_dpms(encoder->base.crtc);
+ }
}
-void intel_encoder_prepare(struct drm_encoder *encoder)
+/* Cross check the actual hw state with our own modeset state tracking (and it's
+ * internal consistency). */
+static void intel_connector_check_state(struct intel_connector *connector)
{
- struct drm_encoder_helper_funcs *encoder_funcs = encoder->helper_private;
- /* lvds has its own version of prepare see intel_lvds_prepare */
- encoder_funcs->dpms(encoder, DRM_MODE_DPMS_OFF);
+ if (connector->get_hw_state(connector)) {
+ struct intel_encoder *encoder = connector->encoder;
+ struct drm_crtc *crtc;
+ bool encoder_enabled;
+ enum pipe pipe;
+
+ DRM_DEBUG_KMS("[CONNECTOR:%d:%s]\n",
+ connector->base.base.id,
+ drm_get_connector_name(&connector->base));
+
+ WARN(connector->base.dpms == DRM_MODE_DPMS_OFF,
+ "wrong connector dpms state\n");
+ WARN(connector->base.encoder != &encoder->base,
+ "active connector not linked to encoder\n");
+ WARN(!encoder->connectors_active,
+ "encoder->connectors_active not set\n");
+
+ encoder_enabled = encoder->get_hw_state(encoder, &pipe);
+ WARN(!encoder_enabled, "encoder not enabled\n");
+ if (WARN_ON(!encoder->base.crtc))
+ return;
+
+ crtc = encoder->base.crtc;
+
+ WARN(!crtc->enabled, "crtc not enabled\n");
+ WARN(!to_intel_crtc(crtc)->active, "crtc not active\n");
+ WARN(pipe != to_intel_crtc(crtc)->pipe,
+ "encoder active on the wrong pipe\n");
+ }
}
-void intel_encoder_commit(struct drm_encoder *encoder)
+/* Even simpler default implementation, if there's really no special case to
+ * consider. */
+void intel_connector_dpms(struct drm_connector *connector, int mode)
{
- struct drm_encoder_helper_funcs *encoder_funcs = encoder->helper_private;
- struct drm_device *dev = encoder->dev;
- struct intel_crtc *intel_crtc = to_intel_crtc(encoder->crtc);
+ struct intel_encoder *encoder = intel_attached_encoder(connector);
- /* lvds has its own version of commit see intel_lvds_commit */
- encoder_funcs->dpms(encoder, DRM_MODE_DPMS_ON);
+ /* All the simple cases only support two dpms states. */
+ if (mode != DRM_MODE_DPMS_ON)
+ mode = DRM_MODE_DPMS_OFF;
- if (HAS_PCH_CPT(dev))
- intel_cpt_verify_modeset(dev, intel_crtc->pipe);
+ if (mode == connector->dpms)
+ return;
+
+ connector->dpms = mode;
+
+ /* Only need to change hw state when actually enabled */
+ if (encoder->base.crtc)
+ intel_encoder_dpms(encoder, mode);
+ else
+ WARN_ON(encoder->connectors_active != false);
+
+ intel_modeset_check_state(connector->dev);
}
-void intel_encoder_destroy(struct drm_encoder *encoder)
+/* Simple connector->get_hw_state implementation for encoders that support only
+ * one connector and no cloning and hence the encoder state determines the state
+ * of the connector. */
+bool intel_connector_get_hw_state(struct intel_connector *connector)
{
- struct intel_encoder *intel_encoder = to_intel_encoder(encoder);
+ enum pipe pipe = 0;
+ struct intel_encoder *encoder = connector->encoder;
- drm_encoder_cleanup(encoder);
- kfree(intel_encoder);
+ return encoder->get_hw_state(encoder, &pipe);
}
static bool intel_crtc_mode_fixup(struct drm_crtc *crtc,
if (!(adjusted_mode->private_flags & INTEL_MODE_CRTC_TIMINGS_SET))
drm_mode_set_crtcinfo(adjusted_mode, 0);
+ /* WaPruneModeWithIncorrectHsyncOffset: Cantiga+ cannot handle modes
+ * with a hsync front porch of 0.
+ */
+ if ((INTEL_INFO(dev)->gen > 4 || IS_G4X(dev)) &&
+ adjusted_mode->hsync_start == adjusted_mode->hdisplay)
+ return false;
+
return true;
}
* true if they don't match).
*/
static bool intel_choose_pipe_bpp_dither(struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
unsigned int *pipe_bpp,
struct drm_display_mode *mode)
{
* also stays within the max display bpc discovered above.
*/
- switch (crtc->fb->depth) {
+ switch (fb->depth) {
case 8:
bpc = 8; /* since we go through a colormap */
break;
struct drm_display_mode *mode,
struct drm_display_mode *adjusted_mode,
int x, int y,
- struct drm_framebuffer *old_fb)
+ struct drm_framebuffer *fb)
{
struct drm_device *dev = crtc->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
I915_WRITE(DSPCNTR(plane), dspcntr);
POSTING_READ(DSPCNTR(plane));
- ret = intel_pipe_set_base(crtc, x, y, old_fb);
+ ret = intel_pipe_set_base(crtc, x, y, fb);
intel_update_watermarks(dev);
return 120000;
}
-static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
- struct drm_display_mode *mode,
+static void ironlake_set_pipeconf(struct drm_crtc *crtc,
struct drm_display_mode *adjusted_mode,
- int x, int y,
- struct drm_framebuffer *old_fb)
+ bool dither)
{
- struct drm_device *dev = crtc->dev;
- struct drm_i915_private *dev_priv = dev->dev_private;
+ struct drm_i915_private *dev_priv = crtc->dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
int pipe = intel_crtc->pipe;
- int plane = intel_crtc->plane;
- int refclk, num_connectors = 0;
- intel_clock_t clock, reduced_clock;
- u32 dpll, fp = 0, fp2 = 0, dspcntr, pipeconf;
- bool ok, has_reduced_clock = false, is_sdvo = false;
- bool is_crt = false, is_lvds = false, is_tv = false, is_dp = false;
- struct intel_encoder *encoder, *edp_encoder = NULL;
+ uint32_t val;
+
+ val = I915_READ(PIPECONF(pipe));
+
+ val &= ~PIPE_BPC_MASK;
+ switch (intel_crtc->bpp) {
+ case 18:
+ val |= PIPE_6BPC;
+ break;
+ case 24:
+ val |= PIPE_8BPC;
+ break;
+ case 30:
+ val |= PIPE_10BPC;
+ break;
+ case 36:
+ val |= PIPE_12BPC;
+ break;
+ default:
+ val |= PIPE_8BPC;
+ break;
+ }
+
+ val &= ~(PIPECONF_DITHER_EN | PIPECONF_DITHER_TYPE_MASK);
+ if (dither)
+ val |= (PIPECONF_DITHER_EN | PIPECONF_DITHER_TYPE_SP);
+
+ val &= ~PIPECONF_INTERLACE_MASK;
+ if (adjusted_mode->flags & DRM_MODE_FLAG_INTERLACE)
+ val |= PIPECONF_INTERLACED_ILK;
+ else
+ val |= PIPECONF_PROGRESSIVE;
+
+ I915_WRITE(PIPECONF(pipe), val);
+ POSTING_READ(PIPECONF(pipe));
+}
+
+static bool ironlake_compute_clocks(struct drm_crtc *crtc,
+ struct drm_display_mode *adjusted_mode,
+ intel_clock_t *clock,
+ bool *has_reduced_clock,
+ intel_clock_t *reduced_clock)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_encoder *intel_encoder;
+ int refclk;
const intel_limit_t *limit;
- int ret;
- struct fdi_m_n m_n = {0};
- u32 temp;
- int target_clock, pixel_multiplier, lane, link_bw, factor;
- unsigned int pipe_bpp;
- bool dither;
- bool is_cpu_edp = false, is_pch_edp = false;
+ bool ret, is_sdvo = false, is_tv = false, is_lvds = false;
- for_each_encoder_on_crtc(dev, crtc, encoder) {
- switch (encoder->type) {
+ for_each_encoder_on_crtc(dev, crtc, intel_encoder) {
+ switch (intel_encoder->type) {
case INTEL_OUTPUT_LVDS:
is_lvds = true;
break;
case INTEL_OUTPUT_SDVO:
case INTEL_OUTPUT_HDMI:
is_sdvo = true;
- if (encoder->needs_tv_clock)
+ if (intel_encoder->needs_tv_clock)
is_tv = true;
break;
case INTEL_OUTPUT_TVOUT:
is_tv = true;
break;
- case INTEL_OUTPUT_ANALOG:
- is_crt = true;
- break;
- case INTEL_OUTPUT_DISPLAYPORT:
- is_dp = true;
- break;
- case INTEL_OUTPUT_EDP:
- is_dp = true;
- if (intel_encoder_is_pch_edp(&encoder->base))
- is_pch_edp = true;
- else
- is_cpu_edp = true;
- edp_encoder = encoder;
- break;
}
-
- num_connectors++;
}
refclk = ironlake_get_refclk(crtc);
* reflck * (5 * (m1 + 2) + (m2 + 2)) / (n + 2) / p1 / p2.
*/
limit = intel_limit(crtc, refclk);
- ok = limit->find_pll(limit, crtc, adjusted_mode->clock, refclk, NULL,
- &clock);
- if (!ok) {
- DRM_ERROR("Couldn't find PLL settings for mode!\n");
- return -EINVAL;
- }
-
- /* Ensure that the cursor is valid for the new mode before changing... */
- intel_crtc_update_cursor(crtc, true);
+ ret = limit->find_pll(limit, crtc, adjusted_mode->clock, refclk, NULL,
+ clock);
+ if (!ret)
+ return false;
if (is_lvds && dev_priv->lvds_downclock_avail) {
/*
* by using the FP0/FP1. In such case we will disable the LVDS
* downclock feature.
*/
- has_reduced_clock = limit->find_pll(limit, crtc,
- dev_priv->lvds_downclock,
- refclk,
- &clock,
- &reduced_clock);
+ *has_reduced_clock = limit->find_pll(limit, crtc,
+ dev_priv->lvds_downclock,
+ refclk,
+ clock,
+ reduced_clock);
}
if (is_sdvo && is_tv)
- i9xx_adjust_sdvo_tv_clock(adjusted_mode, &clock);
+ i9xx_adjust_sdvo_tv_clock(adjusted_mode, clock);
+
+ return true;
+}
+
+static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode,
+ int x, int y,
+ struct drm_framebuffer *fb)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int pipe = intel_crtc->pipe;
+ int plane = intel_crtc->plane;
+ int num_connectors = 0;
+ intel_clock_t clock, reduced_clock;
+ u32 dpll, fp = 0, fp2 = 0;
+ bool ok, has_reduced_clock = false, is_sdvo = false;
+ bool is_crt = false, is_lvds = false, is_tv = false, is_dp = false;
+ struct intel_encoder *encoder, *edp_encoder = NULL;
+ int ret;
+ struct fdi_m_n m_n = {0};
+ u32 temp;
+ int target_clock, pixel_multiplier, lane, link_bw, factor;
+ unsigned int pipe_bpp;
+ bool dither;
+ bool is_cpu_edp = false, is_pch_edp = false;
+
+ for_each_encoder_on_crtc(dev, crtc, encoder) {
+ switch (encoder->type) {
+ case INTEL_OUTPUT_LVDS:
+ is_lvds = true;
+ break;
+ case INTEL_OUTPUT_SDVO:
+ case INTEL_OUTPUT_HDMI:
+ is_sdvo = true;
+ if (encoder->needs_tv_clock)
+ is_tv = true;
+ break;
+ case INTEL_OUTPUT_TVOUT:
+ is_tv = true;
+ break;
+ case INTEL_OUTPUT_ANALOG:
+ is_crt = true;
+ break;
+ case INTEL_OUTPUT_DISPLAYPORT:
+ is_dp = true;
+ break;
+ case INTEL_OUTPUT_EDP:
+ is_dp = true;
+ if (intel_encoder_is_pch_edp(&encoder->base))
+ is_pch_edp = true;
+ else
+ is_cpu_edp = true;
+ edp_encoder = encoder;
+ break;
+ }
+
+ num_connectors++;
+ }
+
+ ok = ironlake_compute_clocks(crtc, adjusted_mode, &clock,
+ &has_reduced_clock, &reduced_clock);
+ if (!ok) {
+ DRM_ERROR("Couldn't find PLL settings for mode!\n");
+ return -EINVAL;
+ }
+ /* Ensure that the cursor is valid for the new mode before changing... */
+ intel_crtc_update_cursor(crtc, true);
/* FDI link */
pixel_multiplier = intel_mode_get_pixel_multiplier(adjusted_mode);
target_clock = adjusted_mode->clock;
/* determine panel color depth */
- temp = I915_READ(PIPECONF(pipe));
- temp &= ~PIPE_BPC_MASK;
- dither = intel_choose_pipe_bpp_dither(crtc, &pipe_bpp, mode);
- switch (pipe_bpp) {
- case 18:
- temp |= PIPE_6BPC;
- break;
- case 24:
- temp |= PIPE_8BPC;
- break;
- case 30:
- temp |= PIPE_10BPC;
- break;
- case 36:
- temp |= PIPE_12BPC;
- break;
- default:
+ dither = intel_choose_pipe_bpp_dither(crtc, fb, &pipe_bpp, mode);
+ if (is_lvds && dev_priv->lvds_dither)
+ dither = true;
+
+ if (pipe_bpp != 18 && pipe_bpp != 24 && pipe_bpp != 30 &&
+ pipe_bpp != 36) {
WARN(1, "intel_choose_pipe_bpp returned invalid value %d\n",
- pipe_bpp);
- temp |= PIPE_8BPC;
+ pipe_bpp);
pipe_bpp = 24;
- break;
}
-
intel_crtc->bpp = pipe_bpp;
- I915_WRITE(PIPECONF(pipe), temp);
if (!lane) {
/*
else
dpll |= PLL_REF_INPUT_DREFCLK;
- /* setup pipeconf */
- pipeconf = I915_READ(PIPECONF(pipe));
-
- /* Set up the display plane register */
- dspcntr = DISPPLANE_GAMMA_ENABLE;
-
DRM_DEBUG_KMS("Mode for pipe %d:\n", pipe);
drm_mode_debug_printmodeline(mode);
I915_WRITE(PCH_LVDS, temp);
}
- pipeconf &= ~PIPECONF_DITHER_EN;
- pipeconf &= ~PIPECONF_DITHER_TYPE_MASK;
- if ((is_lvds && dev_priv->lvds_dither) || dither) {
- pipeconf |= PIPECONF_DITHER_EN;
- pipeconf |= PIPECONF_DITHER_TYPE_SP;
- }
if (is_dp && !is_cpu_edp) {
intel_dp_set_m_n(crtc, mode, adjusted_mode);
} else {
}
}
- pipeconf &= ~PIPECONF_INTERLACE_MASK;
if (adjusted_mode->flags & DRM_MODE_FLAG_INTERLACE) {
- pipeconf |= PIPECONF_INTERLACED_ILK;
/* the chip adds 2 halflines automatically */
adjusted_mode->crtc_vtotal -= 1;
adjusted_mode->crtc_vblank_end -= 1;
adjusted_mode->crtc_hsync_start
- adjusted_mode->crtc_htotal/2);
} else {
- pipeconf |= PIPECONF_PROGRESSIVE;
I915_WRITE(VSYNCSHIFT(pipe), 0);
}
if (is_cpu_edp)
ironlake_set_pll_edp(crtc, adjusted_mode->clock);
- I915_WRITE(PIPECONF(pipe), pipeconf);
- POSTING_READ(PIPECONF(pipe));
+ ironlake_set_pipeconf(crtc, adjusted_mode, dither);
intel_wait_for_vblank(dev, pipe);
- I915_WRITE(DSPCNTR(plane), dspcntr);
+ /* Set up the display plane register */
+ I915_WRITE(DSPCNTR(plane), DISPPLANE_GAMMA_ENABLE);
POSTING_READ(DSPCNTR(plane));
- ret = intel_pipe_set_base(crtc, x, y, old_fb);
+ ret = intel_pipe_set_base(crtc, x, y, fb);
intel_update_watermarks(dev);
struct drm_display_mode *mode,
struct drm_display_mode *adjusted_mode,
int x, int y,
- struct drm_framebuffer *old_fb)
+ struct drm_framebuffer *fb)
{
struct drm_device *dev = crtc->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
drm_vblank_pre_modeset(dev, pipe);
ret = dev_priv->display.crtc_mode_set(crtc, mode, adjusted_mode,
- x, y, old_fb);
+ x, y, fb);
drm_vblank_post_modeset(dev, pipe);
- if (ret)
- intel_crtc->dpms_mode = DRM_MODE_DPMS_OFF;
- else
- intel_crtc->dpms_mode = DRM_MODE_DPMS_ON;
-
return ret;
}
I915_WRITE(G4X_AUD_CNTL_ST, i);
}
+static void haswell_write_eld(struct drm_connector *connector,
+ struct drm_crtc *crtc)
+{
+ struct drm_i915_private *dev_priv = connector->dev->dev_private;
+ uint8_t *eld = connector->eld;
+ struct drm_device *dev = crtc->dev;
+ uint32_t eldv;
+ uint32_t i;
+ int len;
+ int pipe = to_intel_crtc(crtc)->pipe;
+ int tmp;
+
+ int hdmiw_hdmiedid = HSW_AUD_EDID_DATA(pipe);
+ int aud_cntl_st = HSW_AUD_DIP_ELD_CTRL(pipe);
+ int aud_config = HSW_AUD_CFG(pipe);
+ int aud_cntrl_st2 = HSW_AUD_PIN_ELD_CP_VLD;
+
+
+ DRM_DEBUG_DRIVER("HDMI: Haswell Audio initialize....\n");
+
+ /* Audio output enable */
+ DRM_DEBUG_DRIVER("HDMI audio: enable codec\n");
+ tmp = I915_READ(aud_cntrl_st2);
+ tmp |= (AUDIO_OUTPUT_ENABLE_A << (pipe * 4));
+ I915_WRITE(aud_cntrl_st2, tmp);
+
+ /* Wait for 1 vertical blank */
+ intel_wait_for_vblank(dev, pipe);
+
+ /* Set ELD valid state */
+ tmp = I915_READ(aud_cntrl_st2);
+ DRM_DEBUG_DRIVER("HDMI audio: pin eld vld status=0x%8x\n", tmp);
+ tmp |= (AUDIO_ELD_VALID_A << (pipe * 4));
+ I915_WRITE(aud_cntrl_st2, tmp);
+ tmp = I915_READ(aud_cntrl_st2);
+ DRM_DEBUG_DRIVER("HDMI audio: eld vld status=0x%8x\n", tmp);
+
+ /* Enable HDMI mode */
+ tmp = I915_READ(aud_config);
+ DRM_DEBUG_DRIVER("HDMI audio: audio conf: 0x%8x\n", tmp);
+ /* clear N_programing_enable and N_value_index */
+ tmp &= ~(AUD_CONFIG_N_VALUE_INDEX | AUD_CONFIG_N_PROG_ENABLE);
+ I915_WRITE(aud_config, tmp);
+
+ DRM_DEBUG_DRIVER("ELD on pipe %c\n", pipe_name(pipe));
+
+ eldv = AUDIO_ELD_VALID_A << (pipe * 4);
+
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT)) {
+ DRM_DEBUG_DRIVER("ELD: DisplayPort detected\n");
+ eld[5] |= (1 << 2); /* Conn_Type, 0x1 = DisplayPort */
+ I915_WRITE(aud_config, AUD_CONFIG_N_VALUE_INDEX); /* 0x1 = DP */
+ } else
+ I915_WRITE(aud_config, 0);
+
+ if (intel_eld_uptodate(connector,
+ aud_cntrl_st2, eldv,
+ aud_cntl_st, IBX_ELD_ADDRESS,
+ hdmiw_hdmiedid))
+ return;
+
+ i = I915_READ(aud_cntrl_st2);
+ i &= ~eldv;
+ I915_WRITE(aud_cntrl_st2, i);
+
+ if (!eld[0])
+ return;
+
+ i = I915_READ(aud_cntl_st);
+ i &= ~IBX_ELD_ADDRESS;
+ I915_WRITE(aud_cntl_st, i);
+ i = (i >> 29) & DIP_PORT_SEL_MASK; /* DIP_Port_Select, 0x1 = PortB */
+ DRM_DEBUG_DRIVER("port num:%d\n", i);
+
+ len = min_t(uint8_t, eld[2], 21); /* 84 bytes of hw ELD buffer */
+ DRM_DEBUG_DRIVER("ELD size %d\n", len);
+ for (i = 0; i < len; i++)
+ I915_WRITE(hdmiw_hdmiedid, *((uint32_t *)eld + i));
+
+ i = I915_READ(aud_cntrl_st2);
+ i |= eldv;
+ I915_WRITE(aud_cntrl_st2, i);
+
+}
+
static void ironlake_write_eld(struct drm_connector *connector,
struct drm_crtc *crtc)
{
int aud_config;
int aud_cntl_st;
int aud_cntrl_st2;
+ int pipe = to_intel_crtc(crtc)->pipe;
if (HAS_PCH_IBX(connector->dev)) {
- hdmiw_hdmiedid = IBX_HDMIW_HDMIEDID_A;
- aud_config = IBX_AUD_CONFIG_A;
- aud_cntl_st = IBX_AUD_CNTL_ST_A;
+ hdmiw_hdmiedid = IBX_HDMIW_HDMIEDID(pipe);
+ aud_config = IBX_AUD_CFG(pipe);
+ aud_cntl_st = IBX_AUD_CNTL_ST(pipe);
aud_cntrl_st2 = IBX_AUD_CNTL_ST2;
} else {
- hdmiw_hdmiedid = CPT_HDMIW_HDMIEDID_A;
- aud_config = CPT_AUD_CONFIG_A;
- aud_cntl_st = CPT_AUD_CNTL_ST_A;
+ hdmiw_hdmiedid = CPT_HDMIW_HDMIEDID(pipe);
+ aud_config = CPT_AUD_CFG(pipe);
+ aud_cntl_st = CPT_AUD_CNTL_ST(pipe);
aud_cntrl_st2 = CPT_AUD_CNTRL_ST2;
}
- i = to_intel_crtc(crtc)->pipe;
- hdmiw_hdmiedid += i * 0x100;
- aud_cntl_st += i * 0x100;
- aud_config += i * 0x100;
-
- DRM_DEBUG_DRIVER("ELD on pipe %c\n", pipe_name(i));
+ DRM_DEBUG_DRIVER("ELD on pipe %c\n", pipe_name(pipe));
i = I915_READ(aud_cntl_st);
- i = (i >> 29) & 0x3; /* DIP_Port_Select, 0x1 = PortB */
+ i = (i >> 29) & DIP_PORT_SEL_MASK; /* DIP_Port_Select, 0x1 = PortB */
if (!i) {
DRM_DEBUG_DRIVER("Audio directed to unknown port\n");
/* operate blindly on all ports */
uint32_t addr;
int ret;
- DRM_DEBUG_KMS("\n");
-
/* if we want to turn off the cursor ignore width and height */
if (!handle) {
DRM_DEBUG_KMS("cursor off\n");
return fb;
}
-bool intel_get_load_detect_pipe(struct intel_encoder *intel_encoder,
- struct drm_connector *connector,
+bool intel_get_load_detect_pipe(struct drm_connector *connector,
struct drm_display_mode *mode,
struct intel_load_detect_pipe *old)
{
struct intel_crtc *intel_crtc;
+ struct intel_encoder *intel_encoder =
+ intel_attached_encoder(connector);
struct drm_crtc *possible_crtc;
struct drm_encoder *encoder = &intel_encoder->base;
struct drm_crtc *crtc = NULL;
struct drm_device *dev = encoder->dev;
- struct drm_framebuffer *old_fb;
+ struct drm_framebuffer *fb;
int i = -1;
DRM_DEBUG_KMS("[CONNECTOR:%d:%s], [ENCODER:%d:%s]\n",
if (encoder->crtc) {
crtc = encoder->crtc;
- intel_crtc = to_intel_crtc(crtc);
- old->dpms_mode = intel_crtc->dpms_mode;
+ old->dpms_mode = connector->dpms;
old->load_detect_temp = false;
/* Make sure the crtc and connector are running */
- if (intel_crtc->dpms_mode != DRM_MODE_DPMS_ON) {
- struct drm_encoder_helper_funcs *encoder_funcs;
- struct drm_crtc_helper_funcs *crtc_funcs;
-
- crtc_funcs = crtc->helper_private;
- crtc_funcs->dpms(crtc, DRM_MODE_DPMS_ON);
-
- encoder_funcs = encoder->helper_private;
- encoder_funcs->dpms(encoder, DRM_MODE_DPMS_ON);
- }
+ if (connector->dpms != DRM_MODE_DPMS_ON)
+ connector->funcs->dpms(connector, DRM_MODE_DPMS_ON);
return true;
}
return false;
}
- encoder->crtc = crtc;
- connector->encoder = encoder;
+ intel_encoder->new_crtc = to_intel_crtc(crtc);
+ to_intel_connector(connector)->new_encoder = intel_encoder;
intel_crtc = to_intel_crtc(crtc);
- old->dpms_mode = intel_crtc->dpms_mode;
+ old->dpms_mode = connector->dpms;
old->load_detect_temp = true;
old->release_fb = NULL;
if (!mode)
mode = &load_detect_mode;
- old_fb = crtc->fb;
-
/* We need a framebuffer large enough to accommodate all accesses
* that the plane may generate whilst we perform load detection.
* We can not rely on the fbcon either being present (we get called
* not even exist) or that it is large enough to satisfy the
* requested mode.
*/
- crtc->fb = mode_fits_in_fbdev(dev, mode);
- if (crtc->fb == NULL) {
+ fb = mode_fits_in_fbdev(dev, mode);
+ if (fb == NULL) {
DRM_DEBUG_KMS("creating tmp fb for load-detection\n");
- crtc->fb = intel_framebuffer_create_for_mode(dev, mode, 24, 32);
- old->release_fb = crtc->fb;
+ fb = intel_framebuffer_create_for_mode(dev, mode, 24, 32);
+ old->release_fb = fb;
} else
DRM_DEBUG_KMS("reusing fbdev for load-detection framebuffer\n");
- if (IS_ERR(crtc->fb)) {
+ if (IS_ERR(fb)) {
DRM_DEBUG_KMS("failed to allocate framebuffer for load-detection\n");
- crtc->fb = old_fb;
- return false;
+ goto fail;
}
- if (!drm_crtc_helper_set_mode(crtc, mode, 0, 0, old_fb)) {
+ if (!intel_set_mode(crtc, mode, 0, 0, fb)) {
DRM_DEBUG_KMS("failed to set mode on load-detect pipe\n");
if (old->release_fb)
old->release_fb->funcs->destroy(old->release_fb);
- crtc->fb = old_fb;
- return false;
+ goto fail;
}
/* let the connector get through one full cycle before testing */
intel_wait_for_vblank(dev, intel_crtc->pipe);
return true;
+fail:
+ connector->encoder = NULL;
+ encoder->crtc = NULL;
+ return false;
}
-void intel_release_load_detect_pipe(struct intel_encoder *intel_encoder,
- struct drm_connector *connector,
+void intel_release_load_detect_pipe(struct drm_connector *connector,
struct intel_load_detect_pipe *old)
{
+ struct intel_encoder *intel_encoder =
+ intel_attached_encoder(connector);
struct drm_encoder *encoder = &intel_encoder->base;
- struct drm_device *dev = encoder->dev;
- struct drm_crtc *crtc = encoder->crtc;
- struct drm_encoder_helper_funcs *encoder_funcs = encoder->helper_private;
- struct drm_crtc_helper_funcs *crtc_funcs = crtc->helper_private;
DRM_DEBUG_KMS("[CONNECTOR:%d:%s], [ENCODER:%d:%s]\n",
connector->base.id, drm_get_connector_name(connector),
encoder->base.id, drm_get_encoder_name(encoder));
if (old->load_detect_temp) {
- connector->encoder = NULL;
- drm_helper_disable_unused_functions(dev);
+ struct drm_crtc *crtc = encoder->crtc;
+
+ to_intel_connector(connector)->new_encoder = NULL;
+ intel_encoder->new_crtc = NULL;
+ intel_set_mode(crtc, NULL, 0, 0, NULL);
if (old->release_fb)
old->release_fb->funcs->destroy(old->release_fb);
}
/* Switch crtc and encoder back off if necessary */
- if (old->dpms_mode != DRM_MODE_DPMS_ON) {
- encoder_funcs->dpms(encoder, old->dpms_mode);
- crtc_funcs->dpms(crtc, old->dpms_mode);
- }
+ if (old->dpms_mode != DRM_MODE_DPMS_ON)
+ connector->funcs->dpms(connector, old->dpms_mode);
}
/* Returns the clock of the currently programmed mode of the given pipe. */
return mode;
}
-#define GPU_IDLE_TIMEOUT 500 /* ms */
-
-/* When this timer fires, we've been idle for awhile */
-static void intel_gpu_idle_timer(unsigned long arg)
-{
- struct drm_device *dev = (struct drm_device *)arg;
- drm_i915_private_t *dev_priv = dev->dev_private;
-
- if (!list_empty(&dev_priv->mm.active_list)) {
- /* Still processing requests, so just re-arm the timer. */
- mod_timer(&dev_priv->idle_timer, jiffies +
- msecs_to_jiffies(GPU_IDLE_TIMEOUT));
- return;
- }
-
- dev_priv->busy = false;
- queue_work(dev_priv->wq, &dev_priv->idle_work);
-}
-
-#define CRTC_IDLE_TIMEOUT 1000 /* ms */
-
-static void intel_crtc_idle_timer(unsigned long arg)
-{
- struct intel_crtc *intel_crtc = (struct intel_crtc *)arg;
- struct drm_crtc *crtc = &intel_crtc->base;
- drm_i915_private_t *dev_priv = crtc->dev->dev_private;
- struct intel_framebuffer *intel_fb;
-
- intel_fb = to_intel_framebuffer(crtc->fb);
- if (intel_fb && intel_fb->obj->active) {
- /* The framebuffer is still being accessed by the GPU. */
- mod_timer(&intel_crtc->idle_timer, jiffies +
- msecs_to_jiffies(CRTC_IDLE_TIMEOUT));
- return;
- }
-
- intel_crtc->busy = false;
- queue_work(dev_priv->wq, &dev_priv->idle_work);
-}
-
static void intel_increase_pllclock(struct drm_crtc *crtc)
{
struct drm_device *dev = crtc->dev;
if (dpll & DISPLAY_RATE_SELECT_FPA1)
DRM_DEBUG_DRIVER("failed to upclock LVDS!\n");
}
-
- /* Schedule downclock */
- mod_timer(&intel_crtc->idle_timer, jiffies +
- msecs_to_jiffies(CRTC_IDLE_TIMEOUT));
}
static void intel_decrease_pllclock(struct drm_crtc *crtc)
}
-/**
- * intel_idle_update - adjust clocks for idleness
- * @work: work struct
- *
- * Either the GPU or display (or both) went idle. Check the busy status
- * here and adjust the CRTC and GPU clocks as necessary.
- */
-static void intel_idle_update(struct work_struct *work)
+void intel_mark_busy(struct drm_device *dev)
+{
+ i915_update_gfx_val(dev->dev_private);
+}
+
+void intel_mark_idle(struct drm_device *dev)
{
- drm_i915_private_t *dev_priv = container_of(work, drm_i915_private_t,
- idle_work);
- struct drm_device *dev = dev_priv->dev;
+}
+
+void intel_mark_fb_busy(struct drm_i915_gem_object *obj)
+{
+ struct drm_device *dev = obj->base.dev;
struct drm_crtc *crtc;
- struct intel_crtc *intel_crtc;
if (!i915_powersave)
return;
- mutex_lock(&dev->struct_mutex);
-
- i915_update_gfx_val(dev_priv);
-
list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
- /* Skip inactive CRTCs */
if (!crtc->fb)
continue;
- intel_crtc = to_intel_crtc(crtc);
- if (!intel_crtc->busy)
- intel_decrease_pllclock(crtc);
+ if (to_intel_framebuffer(crtc->fb)->obj == obj)
+ intel_increase_pllclock(crtc);
}
-
-
- mutex_unlock(&dev->struct_mutex);
}
-/**
- * intel_mark_busy - mark the GPU and possibly the display busy
- * @dev: drm device
- * @obj: object we're operating on
- *
- * Callers can use this function to indicate that the GPU is busy processing
- * commands. If @obj matches one of the CRTC objects (i.e. it's a scanout
- * buffer), we'll also mark the display as busy, so we know to increase its
- * clock frequency.
- */
-void intel_mark_busy(struct drm_device *dev, struct drm_i915_gem_object *obj)
+void intel_mark_fb_idle(struct drm_i915_gem_object *obj)
{
- drm_i915_private_t *dev_priv = dev->dev_private;
- struct drm_crtc *crtc = NULL;
- struct intel_framebuffer *intel_fb;
- struct intel_crtc *intel_crtc;
-
- if (!drm_core_check_feature(dev, DRIVER_MODESET))
- return;
-
- if (!dev_priv->busy) {
- intel_sanitize_pm(dev);
- dev_priv->busy = true;
- } else
- mod_timer(&dev_priv->idle_timer, jiffies +
- msecs_to_jiffies(GPU_IDLE_TIMEOUT));
+ struct drm_device *dev = obj->base.dev;
+ struct drm_crtc *crtc;
- if (obj == NULL)
+ if (!i915_powersave)
return;
list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
if (!crtc->fb)
continue;
- intel_crtc = to_intel_crtc(crtc);
- intel_fb = to_intel_framebuffer(crtc->fb);
- if (intel_fb->obj == obj) {
- if (!intel_crtc->busy) {
- /* Non-busy -> busy, upclock */
- intel_increase_pllclock(crtc);
- intel_crtc->busy = true;
- } else {
- /* Busy -> busy, put off timer */
- mod_timer(&intel_crtc->idle_timer, jiffies +
- msecs_to_jiffies(CRTC_IDLE_TIMEOUT));
- }
- }
+ if (to_intel_framebuffer(crtc->fb)->obj == obj)
+ intel_decrease_pllclock(crtc);
}
}
default:
WARN_ONCE(1, "unknown plane in flip command\n");
ret = -ENODEV;
- goto err;
+ goto err_unpin;
}
ret = intel_ring_begin(ring, 4);
goto cleanup_pending;
intel_disable_fbc(dev);
- intel_mark_busy(dev, obj);
+ intel_mark_fb_busy(obj);
mutex_unlock(&dev->struct_mutex);
trace_i915_flip_request(intel_crtc->plane, obj);
return ret;
}
-static void intel_sanitize_modesetting(struct drm_device *dev,
- int pipe, int plane)
+static struct drm_crtc_helper_funcs intel_helper_funcs = {
+ .mode_set_base_atomic = intel_pipe_set_base_atomic,
+ .load_lut = intel_crtc_load_lut,
+ .disable = intel_crtc_noop,
+};
+
+bool intel_encoder_check_is_cloned(struct intel_encoder *encoder)
{
- struct drm_i915_private *dev_priv = dev->dev_private;
- u32 reg, val;
- int i;
+ struct intel_encoder *other_encoder;
+ struct drm_crtc *crtc = &encoder->new_crtc->base;
- /* Clear any frame start delays used for debugging left by the BIOS */
- for_each_pipe(i) {
- reg = PIPECONF(i);
- I915_WRITE(reg, I915_READ(reg) & ~PIPECONF_FRAME_START_DELAY_MASK);
+ if (WARN_ON(!crtc))
+ return false;
+
+ list_for_each_entry(other_encoder,
+ &crtc->dev->mode_config.encoder_list,
+ base.head) {
+
+ if (&other_encoder->new_crtc->base != crtc ||
+ encoder == other_encoder)
+ continue;
+ else
+ return true;
}
- if (HAS_PCH_SPLIT(dev))
- return;
+ return false;
+}
- /* Who knows what state these registers were left in by the BIOS or
- * grub?
- *
- * If we leave the registers in a conflicting state (e.g. with the
- * display plane reading from the other pipe than the one we intend
- * to use) then when we attempt to teardown the active mode, we will
- * not disable the pipes and planes in the correct order -- leaving
- * a plane reading from a disabled pipe and possibly leading to
- * undefined behaviour.
+static bool intel_encoder_crtc_ok(struct drm_encoder *encoder,
+ struct drm_crtc *crtc)
+{
+ struct drm_device *dev;
+ struct drm_crtc *tmp;
+ int crtc_mask = 1;
+
+ WARN(!crtc, "checking null crtc?\n");
+
+ dev = crtc->dev;
+
+ list_for_each_entry(tmp, &dev->mode_config.crtc_list, head) {
+ if (tmp == crtc)
+ break;
+ crtc_mask <<= 1;
+ }
+
+ if (encoder->possible_crtcs & crtc_mask)
+ return true;
+ return false;
+}
+
+/**
+ * intel_modeset_update_staged_output_state
+ *
+ * Updates the staged output configuration state, e.g. after we've read out the
+ * current hw state.
+ */
+static void intel_modeset_update_staged_output_state(struct drm_device *dev)
+{
+ struct intel_encoder *encoder;
+ struct intel_connector *connector;
+
+ list_for_each_entry(connector, &dev->mode_config.connector_list,
+ base.head) {
+ connector->new_encoder =
+ to_intel_encoder(connector->base.encoder);
+ }
+
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list,
+ base.head) {
+ encoder->new_crtc =
+ to_intel_crtc(encoder->base.crtc);
+ }
+}
+
+/**
+ * intel_modeset_commit_output_state
+ *
+ * This function copies the stage display pipe configuration to the real one.
+ */
+static void intel_modeset_commit_output_state(struct drm_device *dev)
+{
+ struct intel_encoder *encoder;
+ struct intel_connector *connector;
+
+ list_for_each_entry(connector, &dev->mode_config.connector_list,
+ base.head) {
+ connector->base.encoder = &connector->new_encoder->base;
+ }
+
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list,
+ base.head) {
+ encoder->base.crtc = &encoder->new_crtc->base;
+ }
+}
+
+static struct drm_display_mode *
+intel_modeset_adjusted_mode(struct drm_crtc *crtc,
+ struct drm_display_mode *mode)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_display_mode *adjusted_mode;
+ struct drm_encoder_helper_funcs *encoder_funcs;
+ struct intel_encoder *encoder;
+
+ adjusted_mode = drm_mode_duplicate(dev, mode);
+ if (!adjusted_mode)
+ return ERR_PTR(-ENOMEM);
+
+ /* Pass our mode to the connectors and the CRTC to give them a chance to
+ * adjust it according to limitations or connector properties, and also
+ * a chance to reject the mode entirely.
*/
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list,
+ base.head) {
- reg = DSPCNTR(plane);
- val = I915_READ(reg);
+ if (&encoder->new_crtc->base != crtc)
+ continue;
+ encoder_funcs = encoder->base.helper_private;
+ if (!(encoder_funcs->mode_fixup(&encoder->base, mode,
+ adjusted_mode))) {
+ DRM_DEBUG_KMS("Encoder fixup failed\n");
+ goto fail;
+ }
+ }
- if ((val & DISPLAY_PLANE_ENABLE) == 0)
- return;
- if (!!(val & DISPPLANE_SEL_PIPE_MASK) == pipe)
- return;
+ if (!(intel_crtc_mode_fixup(crtc, mode, adjusted_mode))) {
+ DRM_DEBUG_KMS("CRTC fixup failed\n");
+ goto fail;
+ }
+ DRM_DEBUG_KMS("[CRTC:%d]\n", crtc->base.id);
- /* This display plane is active and attached to the other CPU pipe. */
- pipe = !pipe;
+ return adjusted_mode;
+fail:
+ drm_mode_destroy(dev, adjusted_mode);
+ return ERR_PTR(-EINVAL);
+}
- /* Disable the plane and wait for it to stop reading from the pipe. */
- intel_disable_plane(dev_priv, plane, pipe);
- intel_disable_pipe(dev_priv, pipe);
+/* Computes which crtcs are affected and sets the relevant bits in the mask. For
+ * simplicity we use the crtc's pipe number (because it's easier to obtain). */
+static void
+intel_modeset_affected_pipes(struct drm_crtc *crtc, unsigned *modeset_pipes,
+ unsigned *prepare_pipes, unsigned *disable_pipes)
+{
+ struct intel_crtc *intel_crtc;
+ struct drm_device *dev = crtc->dev;
+ struct intel_encoder *encoder;
+ struct intel_connector *connector;
+ struct drm_crtc *tmp_crtc;
+
+ *disable_pipes = *modeset_pipes = *prepare_pipes = 0;
+
+ /* Check which crtcs have changed outputs connected to them, these need
+ * to be part of the prepare_pipes mask. We don't (yet) support global
+ * modeset across multiple crtcs, so modeset_pipes will only have one
+ * bit set at most. */
+ list_for_each_entry(connector, &dev->mode_config.connector_list,
+ base.head) {
+ if (connector->base.encoder == &connector->new_encoder->base)
+ continue;
+
+ if (connector->base.encoder) {
+ tmp_crtc = connector->base.encoder->crtc;
+
+ *prepare_pipes |= 1 << to_intel_crtc(tmp_crtc)->pipe;
+ }
+
+ if (connector->new_encoder)
+ *prepare_pipes |=
+ 1 << connector->new_encoder->new_crtc->pipe;
+ }
+
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list,
+ base.head) {
+ if (encoder->base.crtc == &encoder->new_crtc->base)
+ continue;
+
+ if (encoder->base.crtc) {
+ tmp_crtc = encoder->base.crtc;
+
+ *prepare_pipes |= 1 << to_intel_crtc(tmp_crtc)->pipe;
+ }
+
+ if (encoder->new_crtc)
+ *prepare_pipes |= 1 << encoder->new_crtc->pipe;
+ }
+
+ /* Check for any pipes that will be fully disabled ... */
+ list_for_each_entry(intel_crtc, &dev->mode_config.crtc_list,
+ base.head) {
+ bool used = false;
+
+ /* Don't try to disable disabled crtcs. */
+ if (!intel_crtc->base.enabled)
+ continue;
+
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list,
+ base.head) {
+ if (encoder->new_crtc == intel_crtc)
+ used = true;
+ }
+
+ if (!used)
+ *disable_pipes |= 1 << intel_crtc->pipe;
+ }
+
+
+ /* set_mode is also used to update properties on life display pipes. */
+ intel_crtc = to_intel_crtc(crtc);
+ if (crtc->enabled)
+ *prepare_pipes |= 1 << intel_crtc->pipe;
+
+ /* We only support modeset on one single crtc, hence we need to do that
+ * only for the passed in crtc iff we change anything else than just
+ * disable crtcs.
+ *
+ * This is actually not true, to be fully compatible with the old crtc
+ * helper we automatically disable _any_ output (i.e. doesn't need to be
+ * connected to the crtc we're modesetting on) if it's disconnected.
+ * Which is a rather nutty api (since changed the output configuration
+ * without userspace's explicit request can lead to confusion), but
+ * alas. Hence we currently need to modeset on all pipes we prepare. */
+ if (*prepare_pipes)
+ *modeset_pipes = *prepare_pipes;
+
+ /* ... and mask these out. */
+ *modeset_pipes &= ~(*disable_pipes);
+ *prepare_pipes &= ~(*disable_pipes);
}
-static void intel_crtc_reset(struct drm_crtc *crtc)
+static bool intel_crtc_in_use(struct drm_crtc *crtc)
{
+ struct drm_encoder *encoder;
struct drm_device *dev = crtc->dev;
- struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
- /* Reset flags back to the 'unknown' status so that they
- * will be correctly set on the initial modeset.
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list, head)
+ if (encoder->crtc == crtc)
+ return true;
+
+ return false;
+}
+
+static void
+intel_modeset_update_state(struct drm_device *dev, unsigned prepare_pipes)
+{
+ struct intel_encoder *intel_encoder;
+ struct intel_crtc *intel_crtc;
+ struct drm_connector *connector;
+
+ list_for_each_entry(intel_encoder, &dev->mode_config.encoder_list,
+ base.head) {
+ if (!intel_encoder->base.crtc)
+ continue;
+
+ intel_crtc = to_intel_crtc(intel_encoder->base.crtc);
+
+ if (prepare_pipes & (1 << intel_crtc->pipe))
+ intel_encoder->connectors_active = false;
+ }
+
+ intel_modeset_commit_output_state(dev);
+
+ /* Update computed state. */
+ list_for_each_entry(intel_crtc, &dev->mode_config.crtc_list,
+ base.head) {
+ intel_crtc->base.enabled = intel_crtc_in_use(&intel_crtc->base);
+ }
+
+ list_for_each_entry(connector, &dev->mode_config.connector_list, head) {
+ if (!connector->encoder || !connector->encoder->crtc)
+ continue;
+
+ intel_crtc = to_intel_crtc(connector->encoder->crtc);
+
+ if (prepare_pipes & (1 << intel_crtc->pipe)) {
+ struct drm_property *dpms_property =
+ dev->mode_config.dpms_property;
+
+ connector->dpms = DRM_MODE_DPMS_ON;
+ drm_connector_property_set_value(connector,
+ dpms_property,
+ DRM_MODE_DPMS_ON);
+
+ intel_encoder = to_intel_encoder(connector->encoder);
+ intel_encoder->connectors_active = true;
+ }
+ }
+
+}
+
+#define for_each_intel_crtc_masked(dev, mask, intel_crtc) \
+ list_for_each_entry((intel_crtc), \
+ &(dev)->mode_config.crtc_list, \
+ base.head) \
+ if (mask & (1 <<(intel_crtc)->pipe)) \
+
+void
+intel_modeset_check_state(struct drm_device *dev)
+{
+ struct intel_crtc *crtc;
+ struct intel_encoder *encoder;
+ struct intel_connector *connector;
+
+ list_for_each_entry(connector, &dev->mode_config.connector_list,
+ base.head) {
+ /* This also checks the encoder/connector hw state with the
+ * ->get_hw_state callbacks. */
+ intel_connector_check_state(connector);
+
+ WARN(&connector->new_encoder->base != connector->base.encoder,
+ "connector's staged encoder doesn't match current encoder\n");
+ }
+
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list,
+ base.head) {
+ bool enabled = false;
+ bool active = false;
+ enum pipe pipe, tracked_pipe;
+
+ DRM_DEBUG_KMS("[ENCODER:%d:%s]\n",
+ encoder->base.base.id,
+ drm_get_encoder_name(&encoder->base));
+
+ WARN(&encoder->new_crtc->base != encoder->base.crtc,
+ "encoder's stage crtc doesn't match current crtc\n");
+ WARN(encoder->connectors_active && !encoder->base.crtc,
+ "encoder's active_connectors set, but no crtc\n");
+
+ list_for_each_entry(connector, &dev->mode_config.connector_list,
+ base.head) {
+ if (connector->base.encoder != &encoder->base)
+ continue;
+ enabled = true;
+ if (connector->base.dpms != DRM_MODE_DPMS_OFF)
+ active = true;
+ }
+ WARN(!!encoder->base.crtc != enabled,
+ "encoder's enabled state mismatch "
+ "(expected %i, found %i)\n",
+ !!encoder->base.crtc, enabled);
+ WARN(active && !encoder->base.crtc,
+ "active encoder with no crtc\n");
+
+ WARN(encoder->connectors_active != active,
+ "encoder's computed active state doesn't match tracked active state "
+ "(expected %i, found %i)\n", active, encoder->connectors_active);
+
+ active = encoder->get_hw_state(encoder, &pipe);
+ WARN(active != encoder->connectors_active,
+ "encoder's hw state doesn't match sw tracking "
+ "(expected %i, found %i)\n",
+ encoder->connectors_active, active);
+
+ if (!encoder->base.crtc)
+ continue;
+
+ tracked_pipe = to_intel_crtc(encoder->base.crtc)->pipe;
+ WARN(active && pipe != tracked_pipe,
+ "active encoder's pipe doesn't match"
+ "(expected %i, found %i)\n",
+ tracked_pipe, pipe);
+
+ }
+
+ list_for_each_entry(crtc, &dev->mode_config.crtc_list,
+ base.head) {
+ bool enabled = false;
+ bool active = false;
+
+ DRM_DEBUG_KMS("[CRTC:%d]\n",
+ crtc->base.base.id);
+
+ WARN(crtc->active && !crtc->base.enabled,
+ "active crtc, but not enabled in sw tracking\n");
+
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list,
+ base.head) {
+ if (encoder->base.crtc != &crtc->base)
+ continue;
+ enabled = true;
+ if (encoder->connectors_active)
+ active = true;
+ }
+ WARN(active != crtc->active,
+ "crtc's computed active state doesn't match tracked active state "
+ "(expected %i, found %i)\n", active, crtc->active);
+ WARN(enabled != crtc->base.enabled,
+ "crtc's computed enabled state doesn't match tracked enabled state "
+ "(expected %i, found %i)\n", enabled, crtc->base.enabled);
+
+ assert_pipe(dev->dev_private, crtc->pipe, crtc->active);
+ }
+}
+
+bool intel_set_mode(struct drm_crtc *crtc,
+ struct drm_display_mode *mode,
+ int x, int y, struct drm_framebuffer *fb)
+{
+ struct drm_device *dev = crtc->dev;
+ drm_i915_private_t *dev_priv = dev->dev_private;
+ struct drm_display_mode *adjusted_mode, saved_mode, saved_hwmode;
+ struct drm_encoder_helper_funcs *encoder_funcs;
+ struct drm_encoder *encoder;
+ struct intel_crtc *intel_crtc;
+ unsigned disable_pipes, prepare_pipes, modeset_pipes;
+ bool ret = true;
+
+ intel_modeset_affected_pipes(crtc, &modeset_pipes,
+ &prepare_pipes, &disable_pipes);
+
+ DRM_DEBUG_KMS("set mode pipe masks: modeset: %x, prepare: %x, disable: %x\n",
+ modeset_pipes, prepare_pipes, disable_pipes);
+
+ for_each_intel_crtc_masked(dev, disable_pipes, intel_crtc)
+ intel_crtc_disable(&intel_crtc->base);
+
+ saved_hwmode = crtc->hwmode;
+ saved_mode = crtc->mode;
+
+ /* Hack: Because we don't (yet) support global modeset on multiple
+ * crtcs, we don't keep track of the new mode for more than one crtc.
+ * Hence simply check whether any bit is set in modeset_pipes in all the
+ * pieces of code that are not yet converted to deal with mutliple crtcs
+ * changing their mode at the same time. */
+ adjusted_mode = NULL;
+ if (modeset_pipes) {
+ adjusted_mode = intel_modeset_adjusted_mode(crtc, mode);
+ if (IS_ERR(adjusted_mode)) {
+ return false;
+ }
+ }
+
+ for_each_intel_crtc_masked(dev, prepare_pipes, intel_crtc) {
+ if (intel_crtc->base.enabled)
+ dev_priv->display.crtc_disable(&intel_crtc->base);
+ }
+
+ /* crtc->mode is already used by the ->mode_set callbacks, hence we need
+ * to set it here already despite that we pass it down the callchain.
*/
- intel_crtc->dpms_mode = -1;
+ if (modeset_pipes)
+ crtc->mode = *mode;
+
+ /* Only after disabling all output pipelines that will be changed can we
+ * update the the output configuration. */
+ intel_modeset_update_state(dev, prepare_pipes);
- /* We need to fix up any BIOS configuration that conflicts with
- * our expectations.
+ /* Set up the DPLL and any encoders state that needs to adjust or depend
+ * on the DPLL.
*/
- intel_sanitize_modesetting(dev, intel_crtc->pipe, intel_crtc->plane);
+ for_each_intel_crtc_masked(dev, modeset_pipes, intel_crtc) {
+ ret = !intel_crtc_mode_set(&intel_crtc->base,
+ mode, adjusted_mode,
+ x, y, fb);
+ if (!ret)
+ goto done;
+
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list, head) {
+
+ if (encoder->crtc != &intel_crtc->base)
+ continue;
+
+ DRM_DEBUG_KMS("[ENCODER:%d:%s] set [MODE:%d:%s]\n",
+ encoder->base.id, drm_get_encoder_name(encoder),
+ mode->base.id, mode->name);
+ encoder_funcs = encoder->helper_private;
+ encoder_funcs->mode_set(encoder, mode, adjusted_mode);
+ }
+ }
+
+ /* Now enable the clocks, plane, pipe, and connectors that we set up. */
+ for_each_intel_crtc_masked(dev, prepare_pipes, intel_crtc)
+ dev_priv->display.crtc_enable(&intel_crtc->base);
+
+ if (modeset_pipes) {
+ /* Store real post-adjustment hardware mode. */
+ crtc->hwmode = *adjusted_mode;
+
+ /* Calculate and store various constants which
+ * are later needed by vblank and swap-completion
+ * timestamping. They are derived from true hwmode.
+ */
+ drm_calc_timestamping_constants(crtc);
+ }
+
+ /* FIXME: add subpixel order */
+done:
+ drm_mode_destroy(dev, adjusted_mode);
+ if (!ret && crtc->enabled) {
+ crtc->hwmode = saved_hwmode;
+ crtc->mode = saved_mode;
+ } else {
+ intel_modeset_check_state(dev);
+ }
+
+ return ret;
}
-static struct drm_crtc_helper_funcs intel_helper_funcs = {
- .dpms = intel_crtc_dpms,
- .mode_fixup = intel_crtc_mode_fixup,
- .mode_set = intel_crtc_mode_set,
- .mode_set_base = intel_pipe_set_base,
- .mode_set_base_atomic = intel_pipe_set_base_atomic,
- .load_lut = intel_crtc_load_lut,
- .disable = intel_crtc_disable,
-};
+#undef for_each_intel_crtc_masked
+
+static void intel_set_config_free(struct intel_set_config *config)
+{
+ if (!config)
+ return;
+
+ kfree(config->save_connector_encoders);
+ kfree(config->save_encoder_crtcs);
+ kfree(config);
+}
+
+static int intel_set_config_save_state(struct drm_device *dev,
+ struct intel_set_config *config)
+{
+ struct drm_encoder *encoder;
+ struct drm_connector *connector;
+ int count;
+
+ config->save_encoder_crtcs =
+ kcalloc(dev->mode_config.num_encoder,
+ sizeof(struct drm_crtc *), GFP_KERNEL);
+ if (!config->save_encoder_crtcs)
+ return -ENOMEM;
+
+ config->save_connector_encoders =
+ kcalloc(dev->mode_config.num_connector,
+ sizeof(struct drm_encoder *), GFP_KERNEL);
+ if (!config->save_connector_encoders)
+ return -ENOMEM;
+
+ /* Copy data. Note that driver private data is not affected.
+ * Should anything bad happen only the expected state is
+ * restored, not the drivers personal bookkeeping.
+ */
+ count = 0;
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list, head) {
+ config->save_encoder_crtcs[count++] = encoder->crtc;
+ }
+
+ count = 0;
+ list_for_each_entry(connector, &dev->mode_config.connector_list, head) {
+ config->save_connector_encoders[count++] = connector->encoder;
+ }
+
+ return 0;
+}
+
+static void intel_set_config_restore_state(struct drm_device *dev,
+ struct intel_set_config *config)
+{
+ struct intel_encoder *encoder;
+ struct intel_connector *connector;
+ int count;
+
+ count = 0;
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list, base.head) {
+ encoder->new_crtc =
+ to_intel_crtc(config->save_encoder_crtcs[count++]);
+ }
+
+ count = 0;
+ list_for_each_entry(connector, &dev->mode_config.connector_list, base.head) {
+ connector->new_encoder =
+ to_intel_encoder(config->save_connector_encoders[count++]);
+ }
+}
+
+static void
+intel_set_config_compute_mode_changes(struct drm_mode_set *set,
+ struct intel_set_config *config)
+{
+
+ /* We should be able to check here if the fb has the same properties
+ * and then just flip_or_move it */
+ if (set->crtc->fb != set->fb) {
+ /* If we have no fb then treat it as a full mode set */
+ if (set->crtc->fb == NULL) {
+ DRM_DEBUG_KMS("crtc has no fb, full mode set\n");
+ config->mode_changed = true;
+ } else if (set->fb == NULL) {
+ config->mode_changed = true;
+ } else if (set->fb->depth != set->crtc->fb->depth) {
+ config->mode_changed = true;
+ } else if (set->fb->bits_per_pixel !=
+ set->crtc->fb->bits_per_pixel) {
+ config->mode_changed = true;
+ } else
+ config->fb_changed = true;
+ }
+
+ if (set->fb && (set->x != set->crtc->x || set->y != set->crtc->y))
+ config->fb_changed = true;
+
+ if (set->mode && !drm_mode_equal(set->mode, &set->crtc->mode)) {
+ DRM_DEBUG_KMS("modes are different, full mode set\n");
+ drm_mode_debug_printmodeline(&set->crtc->mode);
+ drm_mode_debug_printmodeline(set->mode);
+ config->mode_changed = true;
+ }
+}
+
+static int
+intel_modeset_stage_output_state(struct drm_device *dev,
+ struct drm_mode_set *set,
+ struct intel_set_config *config)
+{
+ struct drm_crtc *new_crtc;
+ struct intel_connector *connector;
+ struct intel_encoder *encoder;
+ int count, ro;
+
+ /* The upper layers ensure that we either disabl a crtc or have a list
+ * of connectors. For paranoia, double-check this. */
+ WARN_ON(!set->fb && (set->num_connectors != 0));
+ WARN_ON(set->fb && (set->num_connectors == 0));
+
+ count = 0;
+ list_for_each_entry(connector, &dev->mode_config.connector_list,
+ base.head) {
+ /* Otherwise traverse passed in connector list and get encoders
+ * for them. */
+ for (ro = 0; ro < set->num_connectors; ro++) {
+ if (set->connectors[ro] == &connector->base) {
+ connector->new_encoder = connector->encoder;
+ break;
+ }
+ }
+
+ /* If we disable the crtc, disable all its connectors. Also, if
+ * the connector is on the changing crtc but not on the new
+ * connector list, disable it. */
+ if ((!set->fb || ro == set->num_connectors) &&
+ connector->base.encoder &&
+ connector->base.encoder->crtc == set->crtc) {
+ connector->new_encoder = NULL;
+
+ DRM_DEBUG_KMS("[CONNECTOR:%d:%s] to [NOCRTC]\n",
+ connector->base.base.id,
+ drm_get_connector_name(&connector->base));
+ }
+
+
+ if (&connector->new_encoder->base != connector->base.encoder) {
+ DRM_DEBUG_KMS("encoder changed, full mode switch\n");
+ config->mode_changed = true;
+ }
+
+ /* Disable all disconnected encoders. */
+ if (connector->base.status == connector_status_disconnected)
+ connector->new_encoder = NULL;
+ }
+ /* connector->new_encoder is now updated for all connectors. */
+
+ /* Update crtc of enabled connectors. */
+ count = 0;
+ list_for_each_entry(connector, &dev->mode_config.connector_list,
+ base.head) {
+ if (!connector->new_encoder)
+ continue;
+
+ new_crtc = connector->new_encoder->base.crtc;
+
+ for (ro = 0; ro < set->num_connectors; ro++) {
+ if (set->connectors[ro] == &connector->base)
+ new_crtc = set->crtc;
+ }
+
+ /* Make sure the new CRTC will work with the encoder */
+ if (!intel_encoder_crtc_ok(&connector->new_encoder->base,
+ new_crtc)) {
+ return -EINVAL;
+ }
+ connector->encoder->new_crtc = to_intel_crtc(new_crtc);
+
+ DRM_DEBUG_KMS("[CONNECTOR:%d:%s] to [CRTC:%d]\n",
+ connector->base.base.id,
+ drm_get_connector_name(&connector->base),
+ new_crtc->base.id);
+ }
+
+ /* Check for any encoders that needs to be disabled. */
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list,
+ base.head) {
+ list_for_each_entry(connector,
+ &dev->mode_config.connector_list,
+ base.head) {
+ if (connector->new_encoder == encoder) {
+ WARN_ON(!connector->new_encoder->new_crtc);
+
+ goto next_encoder;
+ }
+ }
+ encoder->new_crtc = NULL;
+next_encoder:
+ /* Only now check for crtc changes so we don't miss encoders
+ * that will be disabled. */
+ if (&encoder->new_crtc->base != encoder->base.crtc) {
+ DRM_DEBUG_KMS("crtc changed, full mode switch\n");
+ config->mode_changed = true;
+ }
+ }
+ /* Now we've also updated encoder->new_crtc for all encoders. */
+
+ return 0;
+}
+
+static int intel_crtc_set_config(struct drm_mode_set *set)
+{
+ struct drm_device *dev;
+ struct drm_mode_set save_set;
+ struct intel_set_config *config;
+ int ret;
+
+ BUG_ON(!set);
+ BUG_ON(!set->crtc);
+ BUG_ON(!set->crtc->helper_private);
+
+ if (!set->mode)
+ set->fb = NULL;
+
+ /* The fb helper likes to play gross jokes with ->mode_set_config.
+ * Unfortunately the crtc helper doesn't do much at all for this case,
+ * so we have to cope with this madness until the fb helper is fixed up. */
+ if (set->fb && set->num_connectors == 0)
+ return 0;
+
+ if (set->fb) {
+ DRM_DEBUG_KMS("[CRTC:%d] [FB:%d] #connectors=%d (x y) (%i %i)\n",
+ set->crtc->base.id, set->fb->base.id,
+ (int)set->num_connectors, set->x, set->y);
+ } else {
+ DRM_DEBUG_KMS("[CRTC:%d] [NOFB]\n", set->crtc->base.id);
+ }
+
+ dev = set->crtc->dev;
+
+ ret = -ENOMEM;
+ config = kzalloc(sizeof(*config), GFP_KERNEL);
+ if (!config)
+ goto out_config;
+
+ ret = intel_set_config_save_state(dev, config);
+ if (ret)
+ goto out_config;
+
+ save_set.crtc = set->crtc;
+ save_set.mode = &set->crtc->mode;
+ save_set.x = set->crtc->x;
+ save_set.y = set->crtc->y;
+ save_set.fb = set->crtc->fb;
+
+ /* Compute whether we need a full modeset, only an fb base update or no
+ * change at all. In the future we might also check whether only the
+ * mode changed, e.g. for LVDS where we only change the panel fitter in
+ * such cases. */
+ intel_set_config_compute_mode_changes(set, config);
+
+ ret = intel_modeset_stage_output_state(dev, set, config);
+ if (ret)
+ goto fail;
+
+ if (config->mode_changed) {
+ if (set->mode) {
+ DRM_DEBUG_KMS("attempting to set mode from"
+ " userspace\n");
+ drm_mode_debug_printmodeline(set->mode);
+ }
+
+ if (!intel_set_mode(set->crtc, set->mode,
+ set->x, set->y, set->fb)) {
+ DRM_ERROR("failed to set mode on [CRTC:%d]\n",
+ set->crtc->base.id);
+ ret = -EINVAL;
+ goto fail;
+ }
+ } else if (config->fb_changed) {
+ ret = intel_pipe_set_base(set->crtc,
+ set->x, set->y, set->fb);
+ }
+
+ intel_set_config_free(config);
+
+ return 0;
+
+fail:
+ intel_set_config_restore_state(dev, config);
+
+ /* Try to restore the config */
+ if (config->mode_changed &&
+ !intel_set_mode(save_set.crtc, save_set.mode,
+ save_set.x, save_set.y, save_set.fb))
+ DRM_ERROR("failed to restore config after modeset failure\n");
+
+out_config:
+ intel_set_config_free(config);
+ return ret;
+}
static const struct drm_crtc_funcs intel_crtc_funcs = {
- .reset = intel_crtc_reset,
.cursor_set = intel_crtc_cursor_set,
.cursor_move = intel_crtc_cursor_move,
.gamma_set = intel_crtc_gamma_set,
- .set_config = drm_crtc_helper_set_config,
+ .set_config = intel_crtc_set_config,
.destroy = intel_crtc_destroy,
.page_flip = intel_crtc_page_flip,
};
dev_priv->plane_to_crtc_mapping[intel_crtc->plane] = &intel_crtc->base;
dev_priv->pipe_to_crtc_mapping[intel_crtc->pipe] = &intel_crtc->base;
- intel_crtc_reset(&intel_crtc->base);
- intel_crtc->active = true; /* force the pipe off on setup_init_config */
intel_crtc->bpp = 24; /* default for pre-Ironlake */
- if (HAS_PCH_SPLIT(dev)) {
- intel_helper_funcs.prepare = ironlake_crtc_prepare;
- intel_helper_funcs.commit = ironlake_crtc_commit;
- } else {
- intel_helper_funcs.prepare = i9xx_crtc_prepare;
- intel_helper_funcs.commit = i9xx_crtc_commit;
- }
-
drm_crtc_helper_add(&intel_crtc->base, &intel_helper_funcs);
-
- intel_crtc->busy = false;
-
- setup_timer(&intel_crtc->idle_timer, intel_crtc_idle_timer,
- (unsigned long)intel_crtc);
}
int intel_get_pipe_from_crtc_id(struct drm_device *dev, void *data,
return 0;
}
-static int intel_encoder_clones(struct drm_device *dev, int type_mask)
+static int intel_encoder_clones(struct intel_encoder *encoder)
{
- struct intel_encoder *encoder;
+ struct drm_device *dev = encoder->base.dev;
+ struct intel_encoder *source_encoder;
int index_mask = 0;
int entry = 0;
- list_for_each_entry(encoder, &dev->mode_config.encoder_list, base.head) {
- if (type_mask & encoder->clone_mask)
+ list_for_each_entry(source_encoder,
+ &dev->mode_config.encoder_list, base.head) {
+
+ if (encoder == source_encoder)
index_mask |= (1 << entry);
+
+ /* Intel hw has only one MUX where enocoders could be cloned. */
+ if (encoder->cloneable && source_encoder->cloneable)
+ index_mask |= (1 << entry);
+
entry++;
}
dpd_is_edp = intel_dpd_is_edp(dev);
if (has_edp_a(dev))
- intel_dp_init(dev, DP_A);
+ intel_dp_init(dev, DP_A, PORT_A);
if (dpd_is_edp && (I915_READ(PCH_DP_D) & DP_DETECTED))
- intel_dp_init(dev, PCH_DP_D);
+ intel_dp_init(dev, PCH_DP_D, PORT_D);
}
intel_crt_init(dev);
/* PCH SDVOB multiplex with HDMIB */
found = intel_sdvo_init(dev, PCH_SDVOB, true);
if (!found)
- intel_hdmi_init(dev, HDMIB);
+ intel_hdmi_init(dev, HDMIB, PORT_B);
if (!found && (I915_READ(PCH_DP_B) & DP_DETECTED))
- intel_dp_init(dev, PCH_DP_B);
+ intel_dp_init(dev, PCH_DP_B, PORT_B);
}
if (I915_READ(HDMIC) & PORT_DETECTED)
- intel_hdmi_init(dev, HDMIC);
+ intel_hdmi_init(dev, HDMIC, PORT_C);
if (!dpd_is_edp && I915_READ(HDMID) & PORT_DETECTED)
- intel_hdmi_init(dev, HDMID);
+ intel_hdmi_init(dev, HDMID, PORT_D);
if (I915_READ(PCH_DP_C) & DP_DETECTED)
- intel_dp_init(dev, PCH_DP_C);
+ intel_dp_init(dev, PCH_DP_C, PORT_C);
if (!dpd_is_edp && (I915_READ(PCH_DP_D) & DP_DETECTED))
- intel_dp_init(dev, PCH_DP_D);
+ intel_dp_init(dev, PCH_DP_D, PORT_D);
} else if (IS_VALLEYVIEW(dev)) {
int found;
/* SDVOB multiplex with HDMIB */
found = intel_sdvo_init(dev, SDVOB, true);
if (!found)
- intel_hdmi_init(dev, SDVOB);
+ intel_hdmi_init(dev, SDVOB, PORT_B);
if (!found && (I915_READ(DP_B) & DP_DETECTED))
- intel_dp_init(dev, DP_B);
+ intel_dp_init(dev, DP_B, PORT_B);
}
if (I915_READ(SDVOC) & PORT_DETECTED)
- intel_hdmi_init(dev, SDVOC);
+ intel_hdmi_init(dev, SDVOC, PORT_C);
/* Shares lanes with HDMI on SDVOC */
if (I915_READ(DP_C) & DP_DETECTED)
- intel_dp_init(dev, DP_C);
+ intel_dp_init(dev, DP_C, PORT_C);
} else if (SUPPORTS_DIGITAL_OUTPUTS(dev)) {
bool found = false;
found = intel_sdvo_init(dev, SDVOB, true);
if (!found && SUPPORTS_INTEGRATED_HDMI(dev)) {
DRM_DEBUG_KMS("probing HDMI on SDVOB\n");
- intel_hdmi_init(dev, SDVOB);
+ intel_hdmi_init(dev, SDVOB, PORT_B);
}
if (!found && SUPPORTS_INTEGRATED_DP(dev)) {
DRM_DEBUG_KMS("probing DP_B\n");
- intel_dp_init(dev, DP_B);
+ intel_dp_init(dev, DP_B, PORT_B);
}
}
if (SUPPORTS_INTEGRATED_HDMI(dev)) {
DRM_DEBUG_KMS("probing HDMI on SDVOC\n");
- intel_hdmi_init(dev, SDVOC);
+ intel_hdmi_init(dev, SDVOC, PORT_C);
}
if (SUPPORTS_INTEGRATED_DP(dev)) {
DRM_DEBUG_KMS("probing DP_C\n");
- intel_dp_init(dev, DP_C);
+ intel_dp_init(dev, DP_C, PORT_C);
}
}
if (SUPPORTS_INTEGRATED_DP(dev) &&
(I915_READ(DP_D) & DP_DETECTED)) {
DRM_DEBUG_KMS("probing DP_D\n");
- intel_dp_init(dev, DP_D);
+ intel_dp_init(dev, DP_D, PORT_D);
}
} else if (IS_GEN2(dev))
intel_dvo_init(dev);
list_for_each_entry(encoder, &dev->mode_config.encoder_list, base.head) {
encoder->base.possible_crtcs = encoder->crtc_mask;
encoder->base.possible_clones =
- intel_encoder_clones(dev, encoder->clone_mask);
+ intel_encoder_clones(encoder);
}
- /* disable all the possible outputs/crtcs before entering KMS mode */
- drm_helper_disable_unused_functions(dev);
-
if (HAS_PCH_IBX(dev) || HAS_PCH_CPT(dev))
ironlake_init_pch_refclk(dev);
}
/* We always want a DPMS function */
if (HAS_PCH_SPLIT(dev)) {
- dev_priv->display.dpms = ironlake_crtc_dpms;
dev_priv->display.crtc_mode_set = ironlake_crtc_mode_set;
+ dev_priv->display.crtc_enable = ironlake_crtc_enable;
+ dev_priv->display.crtc_disable = ironlake_crtc_disable;
dev_priv->display.off = ironlake_crtc_off;
dev_priv->display.update_plane = ironlake_update_plane;
} else {
- dev_priv->display.dpms = i9xx_crtc_dpms;
dev_priv->display.crtc_mode_set = i9xx_crtc_mode_set;
+ dev_priv->display.crtc_enable = i9xx_crtc_enable;
+ dev_priv->display.crtc_disable = i9xx_crtc_disable;
dev_priv->display.off = i9xx_crtc_off;
dev_priv->display.update_plane = i9xx_update_plane;
}
dev_priv->display.write_eld = ironlake_write_eld;
} else if (IS_HASWELL(dev)) {
dev_priv->display.fdi_link_train = hsw_fdi_link_train;
- dev_priv->display.write_eld = ironlake_write_eld;
+ dev_priv->display.write_eld = haswell_write_eld;
} else
dev_priv->display.update_wm = NULL;
} else if (IS_G4X(dev)) {
/* HP Mini needs pipe A force quirk (LP: #322104) */
{ 0x27ae, 0x103c, 0x361a, quirk_pipea_force },
- /* Thinkpad R31 needs pipe A force quirk */
- { 0x3577, 0x1014, 0x0505, quirk_pipea_force },
/* Toshiba Protege R-205, S-209 needs pipe A force quirk */
{ 0x2592, 0x1179, 0x0001, quirk_pipea_force },
- /* ThinkPad X30 needs pipe A force quirk (LP: #304614) */
- { 0x3577, 0x1014, 0x0513, quirk_pipea_force },
- /* ThinkPad X40 needs pipe A force quirk */
-
/* ThinkPad T60 needs pipe A force quirk (bug #16494) */
{ 0x2782, 0x17aa, 0x201a, quirk_pipea_force },
/* 855 & before need to leave pipe A & dpll A up */
{ 0x3582, PCI_ANY_ID, PCI_ANY_ID, quirk_pipea_force },
{ 0x2562, PCI_ANY_ID, PCI_ANY_ID, quirk_pipea_force },
+ { 0x3577, PCI_ANY_ID, PCI_ANY_ID, quirk_pipea_force },
/* Lenovo U160 cannot use SSC on LVDS */
{ 0x0046, 0x17aa, 0x3920, quirk_ssc_force_disable },
/* Just disable it once at startup */
i915_disable_vga(dev);
intel_setup_outputs(dev);
+}
+
+static void
+intel_connector_break_all_links(struct intel_connector *connector)
+{
+ connector->base.dpms = DRM_MODE_DPMS_OFF;
+ connector->base.encoder = NULL;
+ connector->encoder->connectors_active = false;
+ connector->encoder->base.crtc = NULL;
+}
+
+static void intel_enable_pipe_a(struct drm_device *dev)
+{
+ struct intel_connector *connector;
+ struct drm_connector *crt = NULL;
+ struct intel_load_detect_pipe load_detect_temp;
+
+ /* We can't just switch on the pipe A, we need to set things up with a
+ * proper mode and output configuration. As a gross hack, enable pipe A
+ * by enabling the load detect pipe once. */
+ list_for_each_entry(connector,
+ &dev->mode_config.connector_list,
+ base.head) {
+ if (connector->encoder->type == INTEL_OUTPUT_ANALOG) {
+ crt = &connector->base;
+ break;
+ }
+ }
+
+ if (!crt)
+ return;
+
+ if (intel_get_load_detect_pipe(crt, NULL, &load_detect_temp))
+ intel_release_load_detect_pipe(crt, &load_detect_temp);
+
- INIT_WORK(&dev_priv->idle_work, intel_idle_update);
- setup_timer(&dev_priv->idle_timer, intel_gpu_idle_timer,
- (unsigned long)dev);
+}
+
+static void intel_sanitize_crtc(struct intel_crtc *crtc)
+{
+ struct drm_device *dev = crtc->base.dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ u32 reg, val;
+
+ /* Clear any frame start delays used for debugging left by the BIOS */
+ reg = PIPECONF(crtc->pipe);
+ I915_WRITE(reg, I915_READ(reg) & ~PIPECONF_FRAME_START_DELAY_MASK);
+
+ /* We need to sanitize the plane -> pipe mapping first because this will
+ * disable the crtc (and hence change the state) if it is wrong. */
+ if (!HAS_PCH_SPLIT(dev)) {
+ struct intel_connector *connector;
+ bool plane;
+
+ reg = DSPCNTR(crtc->plane);
+ val = I915_READ(reg);
+
+ if ((val & DISPLAY_PLANE_ENABLE) == 0 &&
+ (!!(val & DISPPLANE_SEL_PIPE_MASK) == crtc->pipe))
+ goto ok;
+
+ DRM_DEBUG_KMS("[CRTC:%d] wrong plane connection detected!\n",
+ crtc->base.base.id);
+
+ /* Pipe has the wrong plane attached and the plane is active.
+ * Temporarily change the plane mapping and disable everything
+ * ... */
+ plane = crtc->plane;
+ crtc->plane = !plane;
+ dev_priv->display.crtc_disable(&crtc->base);
+ crtc->plane = plane;
+
+ /* ... and break all links. */
+ list_for_each_entry(connector, &dev->mode_config.connector_list,
+ base.head) {
+ if (connector->encoder->base.crtc != &crtc->base)
+ continue;
+
+ intel_connector_break_all_links(connector);
+ }
+
+ WARN_ON(crtc->active);
+ crtc->base.enabled = false;
+ }
+ok:
+
+ if (dev_priv->quirks & QUIRK_PIPEA_FORCE &&
+ crtc->pipe == PIPE_A && !crtc->active) {
+ /* BIOS forgot to enable pipe A, this mostly happens after
+ * resume. Force-enable the pipe to fix this, the update_dpms
+ * call below we restore the pipe to the right state, but leave
+ * the required bits on. */
+ intel_enable_pipe_a(dev);
+ }
+
+ /* Adjust the state of the output pipe according to whether we
+ * have active connectors/encoders. */
+ intel_crtc_update_dpms(&crtc->base);
+
+ if (crtc->active != crtc->base.enabled) {
+ struct intel_encoder *encoder;
+
+ /* This can happen either due to bugs in the get_hw_state
+ * functions or because the pipe is force-enabled due to the
+ * pipe A quirk. */
+ DRM_DEBUG_KMS("[CRTC:%d] hw state adjusted, was %s, now %s\n",
+ crtc->base.base.id,
+ crtc->base.enabled ? "enabled" : "disabled",
+ crtc->active ? "enabled" : "disabled");
+
+ crtc->base.enabled = crtc->active;
+
+ /* Because we only establish the connector -> encoder ->
+ * crtc links if something is active, this means the
+ * crtc is now deactivated. Break the links. connector
+ * -> encoder links are only establish when things are
+ * actually up, hence no need to break them. */
+ WARN_ON(crtc->active);
+
+ for_each_encoder_on_crtc(dev, &crtc->base, encoder) {
+ WARN_ON(encoder->connectors_active);
+ encoder->base.crtc = NULL;
+ }
+ }
+}
+
+static void intel_sanitize_encoder(struct intel_encoder *encoder)
+{
+ struct intel_connector *connector;
+ struct drm_device *dev = encoder->base.dev;
+
+ /* We need to check both for a crtc link (meaning that the
+ * encoder is active and trying to read from a pipe) and the
+ * pipe itself being active. */
+ bool has_active_crtc = encoder->base.crtc &&
+ to_intel_crtc(encoder->base.crtc)->active;
+
+ if (encoder->connectors_active && !has_active_crtc) {
+ DRM_DEBUG_KMS("[ENCODER:%d:%s] has active connectors but no active pipe!\n",
+ encoder->base.base.id,
+ drm_get_encoder_name(&encoder->base));
+
+ /* Connector is active, but has no active pipe. This is
+ * fallout from our resume register restoring. Disable
+ * the encoder manually again. */
+ if (encoder->base.crtc) {
+ DRM_DEBUG_KMS("[ENCODER:%d:%s] manually disabled\n",
+ encoder->base.base.id,
+ drm_get_encoder_name(&encoder->base));
+ encoder->disable(encoder);
+ }
+
+ /* Inconsistent output/port/pipe state happens presumably due to
+ * a bug in one of the get_hw_state functions. Or someplace else
+ * in our code, like the register restore mess on resume. Clamp
+ * things to off as a safer default. */
+ list_for_each_entry(connector,
+ &dev->mode_config.connector_list,
+ base.head) {
+ if (connector->encoder != encoder)
+ continue;
+
+ intel_connector_break_all_links(connector);
+ }
+ }
+ /* Enabled encoders without active connectors will be fixed in
+ * the crtc fixup. */
+}
+
+/* Scan out the current hw modeset state, sanitizes it and maps it into the drm
+ * and i915 state tracking structures. */
+void intel_modeset_setup_hw_state(struct drm_device *dev)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ enum pipe pipe;
+ u32 tmp;
+ struct intel_crtc *crtc;
+ struct intel_encoder *encoder;
+ struct intel_connector *connector;
+
+ for_each_pipe(pipe) {
+ crtc = to_intel_crtc(dev_priv->pipe_to_crtc_mapping[pipe]);
+
+ tmp = I915_READ(PIPECONF(pipe));
+ if (tmp & PIPECONF_ENABLE)
+ crtc->active = true;
+ else
+ crtc->active = false;
+
+ crtc->base.enabled = crtc->active;
+
+ DRM_DEBUG_KMS("[CRTC:%d] hw state readout: %s\n",
+ crtc->base.base.id,
+ crtc->active ? "enabled" : "disabled");
+ }
+
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list,
+ base.head) {
+ pipe = 0;
+
+ if (encoder->get_hw_state(encoder, &pipe)) {
+ encoder->base.crtc =
+ dev_priv->pipe_to_crtc_mapping[pipe];
+ } else {
+ encoder->base.crtc = NULL;
+ }
+
+ encoder->connectors_active = false;
+ DRM_DEBUG_KMS("[ENCODER:%d:%s] hw state readout: %s, pipe=%i\n",
+ encoder->base.base.id,
+ drm_get_encoder_name(&encoder->base),
+ encoder->base.crtc ? "enabled" : "disabled",
+ pipe);
+ }
+
+ list_for_each_entry(connector, &dev->mode_config.connector_list,
+ base.head) {
+ if (connector->get_hw_state(connector)) {
+ connector->base.dpms = DRM_MODE_DPMS_ON;
+ connector->encoder->connectors_active = true;
+ connector->base.encoder = &connector->encoder->base;
+ } else {
+ connector->base.dpms = DRM_MODE_DPMS_OFF;
+ connector->base.encoder = NULL;
+ }
+ DRM_DEBUG_KMS("[CONNECTOR:%d:%s] hw state readout: %s\n",
+ connector->base.base.id,
+ drm_get_connector_name(&connector->base),
+ connector->base.encoder ? "enabled" : "disabled");
+ }
+
+ /* HW state is read out, now we need to sanitize this mess. */
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list,
+ base.head) {
+ intel_sanitize_encoder(encoder);
+ }
+
+ for_each_pipe(pipe) {
+ crtc = to_intel_crtc(dev_priv->pipe_to_crtc_mapping[pipe]);
+ intel_sanitize_crtc(crtc);
+ }
+
+ intel_modeset_update_staged_output_state(dev);
+
+ intel_modeset_check_state(dev);
}
void intel_modeset_gem_init(struct drm_device *dev)
intel_modeset_init_hw(dev);
intel_setup_overlay(dev);
+
+ intel_modeset_setup_hw_state(dev);
}
void intel_modeset_cleanup(struct drm_device *dev)
* enqueue unpin/hotplug work. */
drm_irq_uninstall(dev);
cancel_work_sync(&dev_priv->hotplug_work);
- cancel_work_sync(&dev_priv->rps_work);
+ cancel_work_sync(&dev_priv->rps.work);
/* flush any delayed tasks or pending work */
flush_scheduled_work();
- /* Shut off idle work before the crtcs get freed. */
- list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
- intel_crtc = to_intel_crtc(crtc);
- del_timer_sync(&intel_crtc->idle_timer);
- }
- del_timer_sync(&dev_priv->idle_timer);
- cancel_work_sync(&dev_priv->idle_work);
-
drm_mode_config_cleanup(dev);
}
u32 position;
u32 base;
u32 size;
- } cursor[2];
+ } cursor[I915_MAX_PIPES];
struct intel_pipe_error_state {
u32 conf;
u32 vtotal;
u32 vblank;
u32 vsync;
- } pipe[2];
+ } pipe[I915_MAX_PIPES];
struct intel_plane_error_state {
u32 control;
u32 addr;
u32 surface;
u32 tile_offset;
- } plane[2];
+ } plane[I915_MAX_PIPES];
};
struct intel_display_error_state *
if (error == NULL)
return NULL;
- for (i = 0; i < 2; i++) {
+ for_each_pipe(i) {
error->cursor[i].control = I915_READ(CURCNTR(i));
error->cursor[i].position = I915_READ(CURPOS(i));
error->cursor[i].base = I915_READ(CURBASE(i));
struct drm_device *dev,
struct intel_display_error_state *error)
{
+ drm_i915_private_t *dev_priv = dev->dev_private;
int i;
- for (i = 0; i < 2; i++) {
+ seq_printf(m, "Num Pipes: %d\n", dev_priv->num_pipe);
+ for_each_pipe(i) {
seq_printf(m, "Pipe [%d]:\n", i);
seq_printf(m, " CONF: %08x\n", error->pipe[i].conf);
seq_printf(m, " SRC: %08x\n", error->pipe[i].source);
projects / linux-2.6-microblaze.git / blobdiff