ARM: sa1100: remove unused board files

[linux-2.6-microblaze.git] / arch / arm / mach-sa1100 / pleb.c

diff --git a/arch/arm/mach-sa1100/pleb.c b/arch/arm/mach-sa1100/pleb.c
deleted file mode 100644 (file)
index b2b0c9f..0000000
--- a/arch/arm/mach-sa1100/pleb.c
+++ /dev/null
@@ -1,148 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * linux/arch/arm/mach-sa1100/pleb.c
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/tty.h>
-#include <linux/ioport.h>
-#include <linux/platform_data/sa11x0-serial.h>
-#include <linux/platform_device.h>
-#include <linux/irq.h>
-#include <linux/io.h>
-#include <linux/mtd/partitions.h>
-#include <linux/smc91x.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-#include <mach/irqs.h>
-
-#include "generic.h"
-
-
-/*
- * Ethernet IRQ mappings
- */
-
-#define PLEB_ETH0_P            (0x20000300)    /* Ethernet 0 in PCMCIA0 IO */
-#define PLEB_ETH0_V            (0xf6000300)
-
-#define GPIO_ETH0_IRQ          GPIO_GPIO(21)
-#define GPIO_ETH0_EN           GPIO_GPIO(26)
-
-#define IRQ_GPIO_ETH0_IRQ      IRQ_GPIO21
-
-static struct resource smc91x_resources[] = {
-       [0] = DEFINE_RES_MEM(PLEB_ETH0_P, 0x04000000),
-#if 0 /* Autoprobe instead, to get rising/falling edge characteristic right */
-       [1] = DEFINE_RES_IRQ(IRQ_GPIO_ETH0_IRQ),
-#endif
-};
-
-static struct smc91x_platdata smc91x_platdata = {
-       .flags = SMC91X_USE_16BIT | SMC91X_USE_8BIT | SMC91X_NOWAIT,
-};
-
-static struct platform_device smc91x_device = {
-       .name           = "smc91x",
-       .id             = 0,
-       .num_resources  = ARRAY_SIZE(smc91x_resources),
-       .resource       = smc91x_resources,
-       .dev = {
-               .platform_data  = &smc91x_platdata,
-       },
-};
-
-static struct platform_device *devices[] __initdata = {
-       &smc91x_device,
-};
-
-
-/*
- * Pleb's memory map
- * has flash memory (typically 4 or 8 meg) selected by
- * the two SA1100 lowest chip select outputs.
- */
-static struct resource pleb_flash_resources[] = {
-       [0] = DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_8M),
-       [1] = DEFINE_RES_MEM(SA1100_CS1_PHYS, SZ_8M),
-};
-
-
-static struct mtd_partition pleb_partitions[] = {
-       {
-               .name           = "blob",
-               .offset         = 0,
-               .size           = 0x00020000,
-       }, {
-               .name           = "kernel",
-               .offset         = MTDPART_OFS_APPEND,
-               .size           = 0x000e0000,
-       }, {
-               .name           = "rootfs",
-               .offset         = MTDPART_OFS_APPEND,
-               .size           = 0x00300000,
-       }
-};
-
-
-static struct flash_platform_data pleb_flash_data = {
-       .map_name = "cfi_probe",
-       .parts = pleb_partitions,
-       .nr_parts = ARRAY_SIZE(pleb_partitions),
-};
-
-
-static void __init pleb_init(void)
-{
-       sa11x0_register_mtd(&pleb_flash_data, pleb_flash_resources,
-                             ARRAY_SIZE(pleb_flash_resources));
-
-
-       platform_add_devices(devices, ARRAY_SIZE(devices));
-}
-
-
-static void __init pleb_map_io(void)
-{
-       sa1100_map_io();
-
-       sa1100_register_uart(0, 3);
-       sa1100_register_uart(1, 1);
-
-       GAFR |= (GPIO_UART_TXD | GPIO_UART_RXD);
-       GPDR |= GPIO_UART_TXD;
-       GPDR &= ~GPIO_UART_RXD;
-       PPAR |= PPAR_UPR;
-
-       /*
-        * Fix expansion memory timing for network card
-        */
-       MECR = ((2<<10) | (2<<5) | (2<<0));
-
-       /*
-        * Enable the SMC ethernet controller
-        */
-       GPDR |= GPIO_ETH0_EN;   /* set to output */
-       GPCR  = GPIO_ETH0_EN;   /* clear MCLK (enable smc) */
-
-       GPDR &= ~GPIO_ETH0_IRQ;
-
-       irq_set_irq_type(GPIO_ETH0_IRQ, IRQ_TYPE_EDGE_FALLING);
-}
-
-MACHINE_START(PLEB, "PLEB")
-       .map_io         = pleb_map_io,
-       .nr_irqs        = SA1100_NR_IRQS,
-       .init_irq       = sa1100_init_irq,
-       .init_time      = sa1100_timer_init,
-       .init_machine   = pleb_init,
-       .init_late      = sa11x0_init_late,
-       .restart        = sa11x0_restart,
-MACHINE_END