--- /dev/null
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2020 MediaTek
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/mediatek,mtu3.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek USB3 DRD Controller Device Tree Bindings
+
+maintainers:
+ - Chunfeng Yun <chunfeng.yun@mediatek.com>
+
+allOf:
+ - $ref: "usb-drd.yaml"
+
+description: |
+ The DRD controller has a glue layer IPPC (IP Port Control), and its host is
+ based on xHCI.
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - mediatek,mt2712-mtu3
+ - mediatek,mt8173-mtu3
+ - mediatek,mt8183-mtu3
+ - const: mediatek,mtu3
+
+ reg:
+ items:
+ - description: the registers of device MAC
+ - description: the registers of IP Port Control
+
+ reg-names:
+ items:
+ - const: mac
+ - const: ippc
+
+ interrupts:
+ maxItems: 1
+
+ power-domains:
+ description: A phandle to USB power domain node to control USB's MTCMOS
+ maxItems: 1
+
+ clocks:
+ minItems: 1
+ items:
+ - description: Controller clock used by normal mode
+ - description: Reference clock used by low power mode etc
+ - description: Mcu bus clock for register access
+ - description: DMA bus clock for data transfer
+
+ clock-names:
+ minItems: 1
+ items:
+ - const: sys_ck # required, others are optional
+ - const: ref_ck
+ - const: mcu_ck
+ - const: dma_ck
+
+ phys:
+ description:
+ List of all the USB PHYs used, it's better to keep the sequence
+ as the hardware layout.
+ minItems: 1
+ items:
+ - description: USB2/HS PHY # required, others are optional
+ - description: USB3/SS(P) PHY
+ - description: USB2/HS PHY # the following for backward compatible
+ - description: USB3/SS(P) PHY
+ - description: USB2/HS PHY
+ - description: USB3/SS(P) PHY
+ - description: USB2/HS PHY
+ - description: USB3/SS(P) PHY
+ - description: USB2/HS PHY
+
+ vusb33-supply:
+ description: Regulator of USB AVDD3.3v
+
+ vbus-supply:
+ deprecated: true
+ description: |
+ Regulator of USB VBUS5v, needed when supports dual-role mode.
+ Particularly, if use an output GPIO to control a VBUS regulator, should
+ model it as a regulator. See bindings/regulator/fixed-regulator.yaml
+ It's considered valid for compatibility reasons, not allowed for
+ new bindings, and put into a usb-connector node.
+
+ dr_mode:
+ enum: [host, peripheral, otg]
+ default: otg
+
+ maximum-speed:
+ enum: [super-speed-plus, super-speed, high-speed, full-speed]
+
+ "#address-cells":
+ enum: [1, 2]
+
+ "#size-cells":
+ enum: [1, 2]
+
+ ranges: true
+
+ extcon:
+ deprecated: true
+ description: |
+ Phandle to the extcon device detecting the IDDIG/VBUS state, neede
+ when supports dual-role mode.
+ It's considered valid for compatibility reasons, not allowed for
+ new bindings, and use "usb-role-switch" property instead.
+
+ usb-role-switch:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: Support role switch.
+ type: boolean
+
+ connector:
+ $ref: /connector/usb-connector.yaml#
+ description:
+ Connector for dual role switch, especially for "gpio-usb-b-connector"
+ type: object
+
+ port:
+ description:
+ Any connector to the data bus of this controller should be modelled
+ using the OF graph bindings specified, if the "usb-role-switch"
+ property is used. See graph.txt
+ type: object
+
+ enable-manual-drd:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ supports manual dual-role switch via debugfs; usually used when
+ receptacle is TYPE-A and also wants to support dual-role mode.
+ type: boolean
+
+ wakeup-source:
+ description: enable USB remote wakeup, see power/wakeup-source.txt
+ type: boolean
+
+ mediatek,syscon-wakeup:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ maxItems: 1
+ description:
+ A phandle to syscon used to access the register of the USB wakeup glue
+ layer between xHCI and SPM, the field should always be 3 cells long.
+ items:
+ items:
+ - description:
+ The first cell represents a phandle to syscon
+ - description:
+ The second cell represents the register base address of the glue
+ layer in syscon
+ - description:
+ The third cell represents the hardware version of the glue layer,
+ 1 is used by mt8173 etc, 2 is used by mt2712 etc
+ enum: [1, 2]
+
+ mediatek,u3p-dis-msk:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: The mask to disable u3ports, bit0 for u3port0,
+ bit1 for u3port1, ... etc
+
+# Required child node when support dual-role
+patternProperties:
+ "^usb@[0-9a-f]+$":
+ type: object
+ $ref: /usb/mediatek,mtk-xhci.yaml#
+ description:
+ The xhci should be added as subnode to mtu3 as shown in the following
+ example if the host mode is enabled.
+
+dependencies:
+ connector: [ 'usb-role-switch' ]
+ port: [ 'usb-role-switch' ]
+ wakeup-source: [ 'mediatek,syscon-wakeup' ]
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - interrupts
+ - clocks
+ - clock-names
+
+additionalProperties: false
+
+examples:
+ # Dual role switch by extcon
+ - |
+ #include <dt-bindings/clock/mt8173-clk.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/phy/phy.h>
+ #include <dt-bindings/power/mt8173-power.h>
+
+ usb@11271000 {
+ compatible = "mediatek,mt8173-mtu3", "mediatek,mtu3";
+ reg = <0x11271000 0x3000>, <0x11280700 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>;
+ phys = <&phy_port0 PHY_TYPE_USB3>, <&phy_port1 PHY_TYPE_USB2>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+ clocks = <&topckgen CLK_TOP_USB30_SEL>;
+ clock-names = "sys_ck";
+ vusb33-supply = <&mt6397_vusb_reg>;
+ vbus-supply = <&usb_p0_vbus>;
+ extcon = <&extcon_usb>;
+ dr_mode = "otg";
+ wakeup-source;
+ mediatek,syscon-wakeup = <&pericfg 0x400 1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ xhci: usb@11270000 {
+ compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci";
+ reg = <0x11270000 0x1000>;
+ reg-names = "mac";
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+ clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
+ clock-names = "sys_ck", "ref_ck";
+ vusb33-supply = <&mt6397_vusb_reg>;
+ };
+ };
+
+ # Enable/disable device by an input gpio for VBUS pin
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/power/mt2712-power.h>
+
+ usb@112c1000 {
+ compatible = "mediatek,mt2712-mtu3", "mediatek,mtu3";
+ reg = <0x112c1000 0x3000>, <0x112d0700 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_LOW>;
+ phys = <&u2port2 PHY_TYPE_USB2>;
+ power-domains = <&scpsys MT2712_POWER_DOMAIN_USB2>;
+ clocks = <&topckgen CLK_TOP_USB30_SEL>;
+ clock-names = "sys_ck";
+ dr_mode = "peripheral";
+ usb-role-switch;
+
+ connector {
+ compatible = "gpio-usb-b-connector", "usb-b-connector";
+ type = "micro";
+ vbus-gpios = <&pio 13 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ # Dual role switch with type-c
+ - |
+ usb@11201000 {
+ compatible ="mediatek,mt8183-mtu3", "mediatek,mtu3";
+ reg = <0x11201000 0x2e00>, <0x11203e00 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_LOW>;
+ phys = <&u2port0 PHY_TYPE_USB2>;
+ clocks = <&clk26m>;
+ clock-names = "sys_ck";
+ mediatek,syscon-wakeup = <&pericfg 0x400 1>;
+ wakeup-source;
+ dr_mode = "otg";
+ usb-role-switch;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ host: usb@11200000 {
+ compatible = "mediatek,mt8183-xhci", "mediatek,mtk-xhci";
+ reg = <0x11200000 0x1000>;
+ reg-names = "mac";
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk26m>;
+ clock-names = "sys_ck";
+ };
+
+ port {
+ usb_role_sw: endpoint {
+ remote-endpoint = <&hs_ep>;
+ };
+ };
+ };
+
+...
projects / linux-2.6-microblaze.git / blobdiff