CONFIG_ACPI_DEBUG must be enabled to produce any ACPI
debug output. Bits in debug_layer correspond to a
_COMPONENT in an ACPI source file, e.g.,
- #define _COMPONENT ACPI_PCI_COMPONENT
+ #define _COMPONENT ACPI_EVENTS
Bits in debug_level correspond to a level in
ACPI_DEBUG_PRINT statements, e.g.,
ACPI_DEBUG_PRINT((ACPI_DB_INFO, ...
Enable processor driver info messages:
acpi.debug_layer=0x20000000
- Enable PCI/PCI interrupt routing info messages:
- acpi.debug_layer=0x400000
Enable AML "Debug" output, i.e., stores to the Debug
object while interpreting AML:
acpi.debug_layer=0xffffffff acpi.debug_level=0x2
cs89x0_media= [HW,NET]
Format: { rj45 | aui | bnc }
+ csdlock_debug= [KNL] Enable debug add-ons of cross-CPU function call
+ handling. When switched on, additional debug data is
+ printed to the console in case a hanging CPU is
+ detected, and that CPU is pinged again in order to try
+ to resolve the hang situation.
+ 0: disable csdlock debugging (default)
+ 1: enable basic csdlock debugging (minor impact)
+ ext: enable extended csdlock debugging (more impact,
+ but more data)
+
dasd= [HW,NET]
See header of drivers/s390/block/dasd_devmap.c.
state is kept private from the host.
Not valid if the kernel is running in EL2.
- Defaults to VHE/nVHE based on hardware support and
- the value of CONFIG_ARM64_VHE.
+ Defaults to VHE/nVHE based on hardware support.
kvm-arm.vgic_v3_group0_trap=
[KVM,ARM] Trap guest accesses to GICv3 group-0
nr_uarts= [SERIAL] maximum number of UARTs to be registered.
- numa_balancing= [KNL,X86] Enable or disable automatic NUMA balancing.
+ numa_balancing= [KNL,ARM64,PPC,RISCV,S390,X86] Enable or disable automatic
+ NUMA balancing.
Allowed values are enable and disable
numa_zonelist_order= [KNL, BOOT] Select zonelist order for NUMA.
Currently this function knows 686a and 8231 chips.
Format: [spp|ps2|epp|ecp|ecpepp]
+ pata_legacy.all= [HW,LIBATA]
+ Format: <int>
+ Set to non-zero to probe primary and secondary ISA
+ port ranges on PCI systems where no PCI PATA device
+ has been found at either range. Disabled by default.
+
+ pata_legacy.autospeed= [HW,LIBATA]
+ Format: <int>
+ Set to non-zero if a chip is present that snoops speed
+ changes. Disabled by default.
+
+ pata_legacy.ht6560a= [HW,LIBATA]
+ Format: <int>
+ Set to 1, 2, or 3 for HT 6560A on the primary channel,
+ the secondary channel, or both channels respectively.
+ Disabled by default.
+
+ pata_legacy.ht6560b= [HW,LIBATA]
+ Format: <int>
+ Set to 1, 2, or 3 for HT 6560B on the primary channel,
+ the secondary channel, or both channels respectively.
+ Disabled by default.
+
+ pata_legacy.iordy_mask= [HW,LIBATA]
+ Format: <int>
+ IORDY enable mask. Set individual bits to allow IORDY
+ for the respective channel. Bit 0 is for the first
+ legacy channel handled by this driver, bit 1 is for
+ the second channel, and so on. The sequence will often
+ correspond to the primary legacy channel, the secondary
+ legacy channel, and so on, but the handling of a PCI
+ bus and the use of other driver options may interfere
+ with the sequence. By default IORDY is allowed across
+ all channels.
+
+ pata_legacy.opti82c46x= [HW,LIBATA]
+ Format: <int>
+ Set to 1, 2, or 3 for Opti 82c611A on the primary
+ channel, the secondary channel, or both channels
+ respectively. Disabled by default.
+
+ pata_legacy.opti82c611a= [HW,LIBATA]
+ Format: <int>
+ Set to 1, 2, or 3 for Opti 82c465MV on the primary
+ channel, the secondary channel, or both channels
+ respectively. Disabled by default.
+
+ pata_legacy.pio_mask= [HW,LIBATA]
+ Format: <int>
+ PIO mode mask for autospeed devices. Set individual
+ bits to allow the use of the respective PIO modes.
+ Bit 0 is for mode 0, bit 1 is for mode 1, and so on.
+ All modes allowed by default.
+
+ pata_legacy.probe_all= [HW,LIBATA]
+ Format: <int>
+ Set to non-zero to probe tertiary and further ISA
+ port ranges on PCI systems. Disabled by default.
+
+ pata_legacy.probe_mask= [HW,LIBATA]
+ Format: <int>
+ Probe mask for legacy ISA PATA ports. Depending on
+ platform configuration and the use of other driver
+ options up to 6 legacy ports are supported: 0x1f0,
+ 0x170, 0x1e8, 0x168, 0x1e0, 0x160, however probing
+ of individual ports can be disabled by setting the
+ corresponding bits in the mask to 1. Bit 0 is for
+ the first port in the list above (0x1f0), and so on.
+ By default all supported ports are probed.
+
+ pata_legacy.qdi= [HW,LIBATA]
+ Format: <int>
+ Set to non-zero to probe QDI controllers. By default
+ set to 1 if CONFIG_PATA_QDI_MODULE, 0 otherwise.
+
+ pata_legacy.winbond= [HW,LIBATA]
+ Format: <int>
+ Set to non-zero to probe Winbond controllers. Use
+ the standard I/O port (0x130) if 1, otherwise the
+ value given is the I/O port to use (typically 0x1b0).
+ By default set to 1 if CONFIG_PATA_WINBOND_VLB_MODULE,
+ 0 otherwise.
+
+ pata_platform.pio_mask= [HW,LIBATA]
+ Format: <int>
+ Supported PIO mode mask. Set individual bits to allow
+ the use of the respective PIO modes. Bit 0 is for
+ mode 0, bit 1 is for mode 1, and so on. Mode 0 only
+ allowed by default.
+
pause_on_oops=
Halt all CPUs after the first oops has been printed for
the specified number of seconds. This is to be used if
fully seed the kernel's CRNG. Default is controlled
by CONFIG_RANDOM_TRUST_CPU.
+ randomize_kstack_offset=
+ [KNL] Enable or disable kernel stack offset
+ randomization, which provides roughly 5 bits of
+ entropy, frustrating memory corruption attacks
+ that depend on stack address determinism or
+ cross-syscall address exposures. This is only
+ available on architectures that have defined
+ CONFIG_HAVE_ARCH_RANDOMIZE_KSTACK_OFFSET.
+ Format: <bool> (1/Y/y=enable, 0/N/n=disable)
+ Default is CONFIG_RANDOMIZE_KSTACK_OFFSET_DEFAULT.
+
ras=option[,option,...] [KNL] RAS-specific options
cec_disable [X86]
see CONFIG_RAS_CEC help text.
rcu_nocbs= [KNL]
- The argument is a cpu list, as described above,
- except that the string "all" can be used to
- specify every CPU on the system.
+ The argument is a cpu list, as described above.
In kernels built with CONFIG_RCU_NOCB_CPU=y, set
the specified list of CPUs to be no-callback CPUs.
rcuscale.kfree_rcu_test= [KNL]
Set to measure performance of kfree_rcu() flooding.
+ rcuscale.kfree_rcu_test_double= [KNL]
+ Test the double-argument variant of kfree_rcu().
+ If this parameter has the same value as
+ rcuscale.kfree_rcu_test_single, both the single-
+ and double-argument variants are tested.
+
+ rcuscale.kfree_rcu_test_single= [KNL]
+ Test the single-argument variant of kfree_rcu().
+ If this parameter has the same value as
+ rcuscale.kfree_rcu_test_double, both the single-
+ and double-argument variants are tested.
+
rcuscale.kfree_nthreads= [KNL]
The number of threads running loops of kfree_rcu().
sbni= [NET] Granch SBNI12 leased line adapter
- sched_debug [KNL] Enables verbose scheduler debug messages.
+ sched_verbose [KNL] Enables verbose scheduler debug messages.
schedstats= [KNL,X86] Enable or disable scheduled statistics.
Allowed values are enable and disable. This feature
slram= [HW,MTD]
+ slab_merge [MM]
+ Enable merging of slabs with similar size when the
+ kernel is built without CONFIG_SLAB_MERGE_DEFAULT.
+
slab_nomerge [MM]
Disable merging of slabs with similar size. May be
necessary if there is some reason to distinguish
lower than slub_max_order.
For more information see Documentation/vm/slub.rst.
+ slub_merge [MM, SLUB]
+ Same with slab_merge.
+
slub_nomerge [MM, SLUB]
Same with slab_nomerge. This is supported for legacy.
See slab_nomerge for more information.
spia_peddr=
split_lock_detect=
- [X86] Enable split lock detection
+ [X86] Enable split lock detection or bus lock detection
When enabled (and if hardware support is present), atomic
instructions that access data across cache line
- boundaries will result in an alignment check exception.
+ boundaries will result in an alignment check exception
+ for split lock detection or a debug exception for
+ bus lock detection.
off - not enabled
- warn - the kernel will emit rate limited warnings
+ warn - the kernel will emit rate-limited warnings
about applications triggering the #AC
- exception. This mode is the default on CPUs
- that supports split lock detection.
+ exception or the #DB exception. This mode is
+ the default on CPUs that support split lock
+ detection or bus lock detection. Default
+ behavior is by #AC if both features are
+ enabled in hardware.
fatal - the kernel will send SIGBUS to applications
- that trigger the #AC exception.
+ that trigger the #AC exception or the #DB
+ exception. Default behavior is by #AC if
+ both features are enabled in hardware.
If an #AC exception is hit in the kernel or in
firmware (i.e. not while executing in user mode)
the kernel will oops in either "warn" or "fatal"
mode.
+ #DB exception for bus lock is triggered only when
+ CPL > 0.
+
srbds= [X86,INTEL]
Control the Special Register Buffer Data Sampling
(SRBDS) mitigation.
projects / linux-2.6-microblaze.git / blobdiff