cs89x0_media= [HW,NET]
Format: { rj45 | aui | bnc }
+ csdlock_debug= [KNL] Enable debug add-ons of cross-CPU function call
+ handling. When switched on, additional debug data is
+ printed to the console in case a hanging CPU is
+ detected, and that CPU is pinged again in order to try
+ to resolve the hang situation.
+ 0: disable csdlock debugging (default)
+ 1: enable basic csdlock debugging (minor impact)
+ ext: enable extended csdlock debugging (more impact,
+ but more data)
+
dasd= [HW,NET]
See header of drivers/s390/block/dasd_devmap.c.
Currently this function knows 686a and 8231 chips.
Format: [spp|ps2|epp|ecp|ecpepp]
+ pata_legacy.all= [HW,LIBATA]
+ Format: <int>
+ Set to non-zero to probe primary and secondary ISA
+ port ranges on PCI systems where no PCI PATA device
+ has been found at either range. Disabled by default.
+
+ pata_legacy.autospeed= [HW,LIBATA]
+ Format: <int>
+ Set to non-zero if a chip is present that snoops speed
+ changes. Disabled by default.
+
+ pata_legacy.ht6560a= [HW,LIBATA]
+ Format: <int>
+ Set to 1, 2, or 3 for HT 6560A on the primary channel,
+ the secondary channel, or both channels respectively.
+ Disabled by default.
+
+ pata_legacy.ht6560b= [HW,LIBATA]
+ Format: <int>
+ Set to 1, 2, or 3 for HT 6560B on the primary channel,
+ the secondary channel, or both channels respectively.
+ Disabled by default.
+
+ pata_legacy.iordy_mask= [HW,LIBATA]
+ Format: <int>
+ IORDY enable mask. Set individual bits to allow IORDY
+ for the respective channel. Bit 0 is for the first
+ legacy channel handled by this driver, bit 1 is for
+ the second channel, and so on. The sequence will often
+ correspond to the primary legacy channel, the secondary
+ legacy channel, and so on, but the handling of a PCI
+ bus and the use of other driver options may interfere
+ with the sequence. By default IORDY is allowed across
+ all channels.
+
+ pata_legacy.opti82c46x= [HW,LIBATA]
+ Format: <int>
+ Set to 1, 2, or 3 for Opti 82c611A on the primary
+ channel, the secondary channel, or both channels
+ respectively. Disabled by default.
+
+ pata_legacy.opti82c611a= [HW,LIBATA]
+ Format: <int>
+ Set to 1, 2, or 3 for Opti 82c465MV on the primary
+ channel, the secondary channel, or both channels
+ respectively. Disabled by default.
+
+ pata_legacy.pio_mask= [HW,LIBATA]
+ Format: <int>
+ PIO mode mask for autospeed devices. Set individual
+ bits to allow the use of the respective PIO modes.
+ Bit 0 is for mode 0, bit 1 is for mode 1, and so on.
+ All modes allowed by default.
+
+ pata_legacy.probe_all= [HW,LIBATA]
+ Format: <int>
+ Set to non-zero to probe tertiary and further ISA
+ port ranges on PCI systems. Disabled by default.
+
+ pata_legacy.probe_mask= [HW,LIBATA]
+ Format: <int>
+ Probe mask for legacy ISA PATA ports. Depending on
+ platform configuration and the use of other driver
+ options up to 6 legacy ports are supported: 0x1f0,
+ 0x170, 0x1e8, 0x168, 0x1e0, 0x160, however probing
+ of individual ports can be disabled by setting the
+ corresponding bits in the mask to 1. Bit 0 is for
+ the first port in the list above (0x1f0), and so on.
+ By default all supported ports are probed.
+
+ pata_legacy.qdi= [HW,LIBATA]
+ Format: <int>
+ Set to non-zero to probe QDI controllers. By default
+ set to 1 if CONFIG_PATA_QDI_MODULE, 0 otherwise.
+
+ pata_legacy.winbond= [HW,LIBATA]
+ Format: <int>
+ Set to non-zero to probe Winbond controllers. Use
+ the standard I/O port (0x130) if 1, otherwise the
+ value given is the I/O port to use (typically 0x1b0).
+ By default set to 1 if CONFIG_PATA_WINBOND_VLB_MODULE,
+ 0 otherwise.
+
+ pata_platform.pio_mask= [HW,LIBATA]
+ Format: <int>
+ Supported PIO mode mask. Set individual bits to allow
+ the use of the respective PIO modes. Bit 0 is for
+ mode 0, bit 1 is for mode 1, and so on. Mode 0 only
+ allowed by default.
+
pause_on_oops=
Halt all CPUs after the first oops has been printed for
the specified number of seconds. This is to be used if
see CONFIG_RAS_CEC help text.
rcu_nocbs= [KNL]
- The argument is a cpu list, as described above,
- except that the string "all" can be used to
- specify every CPU on the system.
+ The argument is a cpu list, as described above.
In kernels built with CONFIG_RCU_NOCB_CPU=y, set
the specified list of CPUs to be no-callback CPUs.
rcuscale.kfree_rcu_test= [KNL]
Set to measure performance of kfree_rcu() flooding.
+ rcuscale.kfree_rcu_test_double= [KNL]
+ Test the double-argument variant of kfree_rcu().
+ If this parameter has the same value as
+ rcuscale.kfree_rcu_test_single, both the single-
+ and double-argument variants are tested.
+
+ rcuscale.kfree_rcu_test_single= [KNL]
+ Test the single-argument variant of kfree_rcu().
+ If this parameter has the same value as
+ rcuscale.kfree_rcu_test_double, both the single-
+ and double-argument variants are tested.
+
rcuscale.kfree_nthreads= [KNL]
The number of threads running loops of kfree_rcu().
sbni= [NET] Granch SBNI12 leased line adapter
- sched_debug [KNL] Enables verbose scheduler debug messages.
+ sched_verbose [KNL] Enables verbose scheduler debug messages.
schedstats= [KNL,X86] Enable or disable scheduled statistics.
Allowed values are enable and disable. This feature
slram= [HW,MTD]
+ slab_merge [MM]
+ Enable merging of slabs with similar size when the
+ kernel is built without CONFIG_SLAB_MERGE_DEFAULT.
+
slab_nomerge [MM]
Disable merging of slabs with similar size. May be
necessary if there is some reason to distinguish
lower than slub_max_order.
For more information see Documentation/vm/slub.rst.
+ slub_merge [MM, SLUB]
+ Same with slab_merge.
+
slub_nomerge [MM, SLUB]
Same with slab_nomerge. This is supported for legacy.
See slab_nomerge for more information.