1 /* SPDX-License-Identifier: GPL-2.0-only */
3 * driver.h -- SoC Regulator driver support.
5 * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC.
7 * Author: Liam Girdwood <lrg@slimlogic.co.uk>
9 * Regulator Driver Interface.
12 #ifndef __LINUX_REGULATOR_DRIVER_H_
13 #define __LINUX_REGULATOR_DRIVER_H_
15 #include <linux/device.h>
16 #include <linux/notifier.h>
17 #include <linux/regulator/consumer.h>
18 #include <linux/ww_mutex.h>
23 struct regulator_config;
24 struct regulator_init_data;
25 struct regulator_enable_gpio;
27 enum regulator_status {
30 REGULATOR_STATUS_ERROR,
31 /* fast/normal/idle/standby are flavors of "on" */
32 REGULATOR_STATUS_FAST,
33 REGULATOR_STATUS_NORMAL,
34 REGULATOR_STATUS_IDLE,
35 REGULATOR_STATUS_STANDBY,
36 /* The regulator is enabled but not regulating */
37 REGULATOR_STATUS_BYPASS,
38 /* in case that any other status doesn't apply */
39 REGULATOR_STATUS_UNDEFINED,
43 * struct regulator_linear_range - specify linear voltage ranges
45 * Specify a range of voltages for regulator_map_linear_range() and
46 * regulator_list_linear_range().
48 * @min_uV: Lowest voltage in range
49 * @min_sel: Lowest selector for range
50 * @max_sel: Highest selector for range
53 struct regulator_linear_range {
60 /* Initialize struct regulator_linear_range */
61 #define REGULATOR_LINEAR_RANGE(_min_uV, _min_sel, _max_sel, _step_uV) \
64 .min_sel = _min_sel, \
65 .max_sel = _max_sel, \
66 .uV_step = _step_uV, \
70 * struct regulator_ops - regulator operations.
72 * @enable: Configure the regulator as enabled.
73 * @disable: Configure the regulator as disabled.
74 * @is_enabled: Return 1 if the regulator is enabled, 0 if not.
75 * May also return negative errno.
77 * @set_voltage: Set the voltage for the regulator within the range specified.
78 * The driver should select the voltage closest to min_uV.
79 * @set_voltage_sel: Set the voltage for the regulator using the specified
81 * @map_voltage: Convert a voltage into a selector
82 * @get_voltage: Return the currently configured voltage for the regulator;
83 * return -ENOTRECOVERABLE if regulator can't be read at
84 * bootup and hasn't been set yet.
85 * @get_voltage_sel: Return the currently configured voltage selector for the
86 * regulator; return -ENOTRECOVERABLE if regulator can't
87 * be read at bootup and hasn't been set yet.
88 * @list_voltage: Return one of the supported voltages, in microvolts; zero
89 * if the selector indicates a voltage that is unusable on this system;
90 * or negative errno. Selectors range from zero to one less than
91 * regulator_desc.n_voltages. Voltages may be reported in any order.
93 * @set_current_limit: Configure a limit for a current-limited regulator.
94 * The driver should select the current closest to max_uA.
95 * @get_current_limit: Get the configured limit for a current-limited regulator.
96 * @set_input_current_limit: Configure an input limit.
98 * @set_over_current_protection: Support capability of automatically shutting
99 * down when detecting an over current event.
101 * @set_active_discharge: Set active discharge enable/disable of regulators.
103 * @set_mode: Set the configured operating mode for the regulator.
104 * @get_mode: Get the configured operating mode for the regulator.
105 * @get_error_flags: Get the current error(s) for the regulator.
106 * @get_status: Return actual (not as-configured) status of regulator, as a
107 * REGULATOR_STATUS value (or negative errno)
108 * @get_optimum_mode: Get the most efficient operating mode for the regulator
109 * when running with the specified parameters.
110 * @set_load: Set the load for the regulator.
112 * @set_bypass: Set the regulator in bypass mode.
113 * @get_bypass: Get the regulator bypass mode state.
115 * @enable_time: Time taken for the regulator voltage output voltage to
116 * stabilise after being enabled, in microseconds.
117 * @set_ramp_delay: Set the ramp delay for the regulator. The driver should
118 * select ramp delay equal to or less than(closest) ramp_delay.
119 * @set_voltage_time: Time taken for the regulator voltage output voltage
120 * to stabilise after being set to a new value, in microseconds.
121 * The function receives the from and to voltage as input, it
122 * should return the worst case.
123 * @set_voltage_time_sel: Time taken for the regulator voltage output voltage
124 * to stabilise after being set to a new value, in microseconds.
125 * The function receives the from and to voltage selector as
126 * input, it should return the worst case.
127 * @set_soft_start: Enable soft start for the regulator.
129 * @set_suspend_voltage: Set the voltage for the regulator when the system
131 * @set_suspend_enable: Mark the regulator as enabled when the system is
133 * @set_suspend_disable: Mark the regulator as disabled when the system is
135 * @set_suspend_mode: Set the operating mode for the regulator when the
136 * system is suspended.
138 * @set_pull_down: Configure the regulator to pull down when the regulator
141 * This struct describes regulator operations which can be implemented by
142 * regulator chip drivers.
144 struct regulator_ops {
146 /* enumerate supported voltages */
147 int (*list_voltage) (struct regulator_dev *, unsigned selector);
149 /* get/set regulator voltage */
150 int (*set_voltage) (struct regulator_dev *, int min_uV, int max_uV,
152 int (*map_voltage)(struct regulator_dev *, int min_uV, int max_uV);
153 int (*set_voltage_sel) (struct regulator_dev *, unsigned selector);
154 int (*get_voltage) (struct regulator_dev *);
155 int (*get_voltage_sel) (struct regulator_dev *);
157 /* get/set regulator current */
158 int (*set_current_limit) (struct regulator_dev *,
159 int min_uA, int max_uA);
160 int (*get_current_limit) (struct regulator_dev *);
162 int (*set_input_current_limit) (struct regulator_dev *, int lim_uA);
163 int (*set_over_current_protection) (struct regulator_dev *);
164 int (*set_active_discharge) (struct regulator_dev *, bool enable);
166 /* enable/disable regulator */
167 int (*enable) (struct regulator_dev *);
168 int (*disable) (struct regulator_dev *);
169 int (*is_enabled) (struct regulator_dev *);
171 /* get/set regulator operating mode (defined in consumer.h) */
172 int (*set_mode) (struct regulator_dev *, unsigned int mode);
173 unsigned int (*get_mode) (struct regulator_dev *);
175 /* retrieve current error flags on the regulator */
176 int (*get_error_flags)(struct regulator_dev *, unsigned int *flags);
178 /* Time taken to enable or set voltage on the regulator */
179 int (*enable_time) (struct regulator_dev *);
180 int (*set_ramp_delay) (struct regulator_dev *, int ramp_delay);
181 int (*set_voltage_time) (struct regulator_dev *, int old_uV,
183 int (*set_voltage_time_sel) (struct regulator_dev *,
184 unsigned int old_selector,
185 unsigned int new_selector);
187 int (*set_soft_start) (struct regulator_dev *);
189 /* report regulator status ... most other accessors report
190 * control inputs, this reports results of combining inputs
191 * from Linux (and other sources) with the actual load.
192 * returns REGULATOR_STATUS_* or negative errno.
194 int (*get_status)(struct regulator_dev *);
196 /* get most efficient regulator operating mode for load */
197 unsigned int (*get_optimum_mode) (struct regulator_dev *, int input_uV,
198 int output_uV, int load_uA);
199 /* set the load on the regulator */
200 int (*set_load)(struct regulator_dev *, int load_uA);
202 /* control and report on bypass mode */
203 int (*set_bypass)(struct regulator_dev *dev, bool enable);
204 int (*get_bypass)(struct regulator_dev *dev, bool *enable);
206 /* the operations below are for configuration of regulator state when
207 * its parent PMIC enters a global STANDBY/HIBERNATE state */
209 /* set regulator suspend voltage */
210 int (*set_suspend_voltage) (struct regulator_dev *, int uV);
212 /* enable/disable regulator in suspend state */
213 int (*set_suspend_enable) (struct regulator_dev *);
214 int (*set_suspend_disable) (struct regulator_dev *);
216 /* set regulator suspend operating mode (defined in consumer.h) */
217 int (*set_suspend_mode) (struct regulator_dev *, unsigned int mode);
219 int (*resume)(struct regulator_dev *rdev);
221 int (*set_pull_down) (struct regulator_dev *);
225 * Regulators can either control voltage or current.
227 enum regulator_type {
233 * struct regulator_desc - Static regulator descriptor
235 * Each regulator registered with the core is described with a
236 * structure of this type and a struct regulator_config. This
237 * structure contains the non-varying parts of the regulator
240 * @name: Identifying name for the regulator.
241 * @supply_name: Identifying the regulator supply
242 * @of_match: Name used to identify regulator in DT.
243 * @regulators_node: Name of node containing regulator definitions in DT.
244 * @of_parse_cb: Optional callback called only if of_match is present.
245 * Will be called for each regulator parsed from DT, during
247 * The regulator_config passed as argument to the callback will
248 * be a copy of config passed to regulator_register, valid only
249 * for this particular call. Callback may freely change the
250 * config but it cannot store it for later usage.
251 * Callback should return 0 on success or negative ERRNO
252 * indicating failure.
253 * @id: Numerical identifier for the regulator.
254 * @ops: Regulator operations table.
255 * @irq: Interrupt number for the regulator.
256 * @type: Indicates if the regulator is a voltage or current regulator.
257 * @owner: Module providing the regulator, used for refcounting.
259 * @continuous_voltage_range: Indicates if the regulator can set any
260 * voltage within constrains range.
261 * @n_voltages: Number of selectors available for ops.list_voltage().
262 * @n_current_limits: Number of selectors available for current limits
264 * @min_uV: Voltage given by the lowest selector (if linear mapping)
265 * @uV_step: Voltage increase with each selector (if linear mapping)
266 * @linear_min_sel: Minimal selector for starting linear mapping
267 * @fixed_uV: Fixed voltage of rails.
268 * @ramp_delay: Time to settle down after voltage change (unit: uV/us)
269 * @min_dropout_uV: The minimum dropout voltage this regulator can handle
270 * @linear_ranges: A constant table of possible voltage ranges.
271 * @linear_range_selectors: A constant table of voltage range selectors.
272 * If pickable ranges are used each range must
273 * have corresponding selector here.
274 * @n_linear_ranges: Number of entries in the @linear_ranges (and in
275 * linear_range_selectors if used) table(s).
276 * @volt_table: Voltage mapping table (if table based mapping)
277 * @curr_table: Current limit mapping table (if table based mapping)
279 * @vsel_range_reg: Register for range selector when using pickable ranges
280 * and regulator_regmap_X_voltage_X_pickable functions.
281 * @vsel_range_mask: Mask for register bitfield used for range selector
282 * @vsel_reg: Register for selector when using regulator_regmap_X_voltage_
283 * @vsel_mask: Mask for register bitfield used for selector
284 * @vsel_step: Specify the resolution of selector stepping when setting
285 * voltage. If 0, then no stepping is done (requested selector is
286 * set directly), if >0 then the regulator API will ramp the
287 * voltage up/down gradually each time increasing/decreasing the
288 * selector by the specified step value.
289 * @csel_reg: Register for current limit selector using regmap set_current_limit
290 * @csel_mask: Mask for register bitfield used for current limit selector
291 * @apply_reg: Register for initiate voltage change on the output when
292 * using regulator_set_voltage_sel_regmap
293 * @apply_bit: Register bitfield used for initiate voltage change on the
294 * output when using regulator_set_voltage_sel_regmap
295 * @enable_reg: Register for control when using regmap enable/disable ops
296 * @enable_mask: Mask for control when using regmap enable/disable ops
297 * @enable_val: Enabling value for control when using regmap enable/disable ops
298 * @disable_val: Disabling value for control when using regmap enable/disable ops
299 * @enable_is_inverted: A flag to indicate set enable_mask bits to disable
300 * when using regulator_enable_regmap and friends APIs.
301 * @bypass_reg: Register for control when using regmap set_bypass
302 * @bypass_mask: Mask for control when using regmap set_bypass
303 * @bypass_val_on: Enabling value for control when using regmap set_bypass
304 * @bypass_val_off: Disabling value for control when using regmap set_bypass
305 * @active_discharge_off: Enabling value for control when using regmap
306 * set_active_discharge
307 * @active_discharge_on: Disabling value for control when using regmap
308 * set_active_discharge
309 * @active_discharge_mask: Mask for control when using regmap
310 * set_active_discharge
311 * @active_discharge_reg: Register for control when using regmap
312 * set_active_discharge
313 * @soft_start_reg: Register for control when using regmap set_soft_start
314 * @soft_start_mask: Mask for control when using regmap set_soft_start
315 * @soft_start_val_on: Enabling value for control when using regmap
317 * @pull_down_reg: Register for control when using regmap set_pull_down
318 * @pull_down_mask: Mask for control when using regmap set_pull_down
319 * @pull_down_val_on: Enabling value for control when using regmap
322 * @enable_time: Time taken for initial enable of regulator (in uS).
323 * @off_on_delay: guard time (in uS), before re-enabling a regulator
325 * @of_map_mode: Maps a hardware mode defined in a DeviceTree to a standard mode
327 struct regulator_desc {
329 const char *supply_name;
330 const char *of_match;
331 const char *regulators_node;
332 int (*of_parse_cb)(struct device_node *,
333 const struct regulator_desc *,
334 struct regulator_config *);
336 unsigned int continuous_voltage_range:1;
338 unsigned int n_current_limits;
339 const struct regulator_ops *ops;
341 enum regulator_type type;
342 struct module *owner;
345 unsigned int uV_step;
346 unsigned int linear_min_sel;
348 unsigned int ramp_delay;
351 const struct regulator_linear_range *linear_ranges;
352 const unsigned int *linear_range_selectors;
356 const unsigned int *volt_table;
357 const unsigned int *curr_table;
359 unsigned int vsel_range_reg;
360 unsigned int vsel_range_mask;
361 unsigned int vsel_reg;
362 unsigned int vsel_mask;
363 unsigned int vsel_step;
364 unsigned int csel_reg;
365 unsigned int csel_mask;
366 unsigned int apply_reg;
367 unsigned int apply_bit;
368 unsigned int enable_reg;
369 unsigned int enable_mask;
370 unsigned int enable_val;
371 unsigned int disable_val;
372 bool enable_is_inverted;
373 unsigned int bypass_reg;
374 unsigned int bypass_mask;
375 unsigned int bypass_val_on;
376 unsigned int bypass_val_off;
377 unsigned int active_discharge_on;
378 unsigned int active_discharge_off;
379 unsigned int active_discharge_mask;
380 unsigned int active_discharge_reg;
381 unsigned int soft_start_reg;
382 unsigned int soft_start_mask;
383 unsigned int soft_start_val_on;
384 unsigned int pull_down_reg;
385 unsigned int pull_down_mask;
386 unsigned int pull_down_val_on;
388 unsigned int enable_time;
390 unsigned int off_on_delay;
392 unsigned int (*of_map_mode)(unsigned int mode);
396 * struct regulator_config - Dynamic regulator descriptor
398 * Each regulator registered with the core is described with a
399 * structure of this type and a struct regulator_desc. This structure
400 * contains the runtime variable parts of the regulator description.
402 * @dev: struct device for the regulator
403 * @init_data: platform provided init data, passed through by driver
404 * @driver_data: private regulator data
405 * @of_node: OpenFirmware node to parse for device tree bindings (may be
407 * @regmap: regmap to use for core regmap helpers if dev_get_regmap() is
409 * @ena_gpiod: GPIO controlling regulator enable.
411 struct regulator_config {
413 const struct regulator_init_data *init_data;
415 struct device_node *of_node;
416 struct regmap *regmap;
418 struct gpio_desc *ena_gpiod;
422 * struct coupling_desc
424 * Describes coupling of regulators. Each regulator should have
425 * at least a pointer to itself in coupled_rdevs array.
426 * When a new coupled regulator is resolved, n_resolved is
429 struct coupling_desc {
430 struct regulator_dev **coupled_rdevs;
431 struct regulator_coupler *coupler;
437 * struct regulator_dev
439 * Voltage / Current regulator class device. One for each
442 * This should *not* be used directly by anything except the regulator
443 * core and notification injection (which should take the mutex and do
444 * no other direct access).
446 struct regulator_dev {
447 const struct regulator_desc *desc;
453 /* lists we belong to */
454 struct list_head list; /* list of all regulators */
457 struct list_head consumer_list; /* consumers we supply */
459 struct coupling_desc coupling_desc;
461 struct blocking_notifier_head notifier;
462 struct ww_mutex mutex; /* consumer lock */
463 struct task_struct *mutex_owner;
465 struct module *owner;
467 struct regulation_constraints *constraints;
468 struct regulator *supply; /* for tree */
469 const char *supply_name;
470 struct regmap *regmap;
472 struct delayed_work disable_work;
474 void *reg_data; /* regulator_dev data */
476 struct dentry *debugfs;
478 struct regulator_enable_gpio *ena_pin;
479 unsigned int ena_gpio_state:1;
481 unsigned int is_switch:1;
483 /* time when this regulator was disabled last time */
484 unsigned long last_off_jiffy;
487 struct regulator_dev *
488 regulator_register(const struct regulator_desc *regulator_desc,
489 const struct regulator_config *config);
490 struct regulator_dev *
491 devm_regulator_register(struct device *dev,
492 const struct regulator_desc *regulator_desc,
493 const struct regulator_config *config);
494 void regulator_unregister(struct regulator_dev *rdev);
495 void devm_regulator_unregister(struct device *dev, struct regulator_dev *rdev);
497 int regulator_notifier_call_chain(struct regulator_dev *rdev,
498 unsigned long event, void *data);
500 void *rdev_get_drvdata(struct regulator_dev *rdev);
501 struct device *rdev_get_dev(struct regulator_dev *rdev);
502 struct regmap *rdev_get_regmap(struct regulator_dev *rdev);
503 int rdev_get_id(struct regulator_dev *rdev);
505 int regulator_mode_to_status(unsigned int);
507 int regulator_list_voltage_linear(struct regulator_dev *rdev,
508 unsigned int selector);
509 int regulator_list_voltage_pickable_linear_range(struct regulator_dev *rdev,
510 unsigned int selector);
511 int regulator_list_voltage_linear_range(struct regulator_dev *rdev,
512 unsigned int selector);
513 int regulator_list_voltage_table(struct regulator_dev *rdev,
514 unsigned int selector);
515 int regulator_map_voltage_linear(struct regulator_dev *rdev,
516 int min_uV, int max_uV);
517 int regulator_map_voltage_pickable_linear_range(struct regulator_dev *rdev,
518 int min_uV, int max_uV);
519 int regulator_map_voltage_linear_range(struct regulator_dev *rdev,
520 int min_uV, int max_uV);
521 int regulator_map_voltage_iterate(struct regulator_dev *rdev,
522 int min_uV, int max_uV);
523 int regulator_map_voltage_ascend(struct regulator_dev *rdev,
524 int min_uV, int max_uV);
525 int regulator_get_voltage_sel_pickable_regmap(struct regulator_dev *rdev);
526 int regulator_set_voltage_sel_pickable_regmap(struct regulator_dev *rdev,
528 int regulator_get_voltage_sel_regmap(struct regulator_dev *rdev);
529 int regulator_set_voltage_sel_regmap(struct regulator_dev *rdev, unsigned sel);
530 int regulator_is_enabled_regmap(struct regulator_dev *rdev);
531 int regulator_enable_regmap(struct regulator_dev *rdev);
532 int regulator_disable_regmap(struct regulator_dev *rdev);
533 int regulator_set_voltage_time_sel(struct regulator_dev *rdev,
534 unsigned int old_selector,
535 unsigned int new_selector);
536 int regulator_set_bypass_regmap(struct regulator_dev *rdev, bool enable);
537 int regulator_get_bypass_regmap(struct regulator_dev *rdev, bool *enable);
538 int regulator_set_soft_start_regmap(struct regulator_dev *rdev);
539 int regulator_set_pull_down_regmap(struct regulator_dev *rdev);
541 int regulator_set_active_discharge_regmap(struct regulator_dev *rdev,
543 int regulator_set_current_limit_regmap(struct regulator_dev *rdev,
544 int min_uA, int max_uA);
545 int regulator_get_current_limit_regmap(struct regulator_dev *rdev);
546 void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data);
548 void regulator_lock(struct regulator_dev *rdev);
549 void regulator_unlock(struct regulator_dev *rdev);
552 * Helper functions intended to be used by regulator drivers prior registering
555 int regulator_desc_list_voltage_linear_range(const struct regulator_desc *desc,
556 unsigned int selector);