5 #include <linux/spinlock.h>
6 #include <linux/workqueue.h>
15 MLO_PAUSE_RX = BIT(0),
16 MLO_PAUSE_TX = BIT(1),
17 MLO_PAUSE_TXRX_MASK = MLO_PAUSE_TX | MLO_PAUSE_RX,
18 MLO_PAUSE_AN = BIT(2),
20 MLO_AN_PHY = 0, /* Conventional PHY */
21 MLO_AN_FIXED, /* Fixed-link mode */
22 MLO_AN_INBAND, /* In-band protocol */
24 /* MAC_SYM_PAUSE and MAC_ASYM_PAUSE are used when configuring our
25 * autonegotiation advertisement. They correspond to the PAUSE and
26 * ASM_DIR bits defined by 802.3, respectively.
28 * The following table lists the values of tx_pause and rx_pause which
29 * might be requested in mac_link_up. The exact values depend on either
30 * the results of autonegotation (if MLO_PAUSE_AN is set) or user
31 * configuration (if MLO_PAUSE_AN is not set).
33 * MAC_SYM_PAUSE MAC_ASYM_PAUSE MLO_PAUSE_AN tx_pause/rx_pause
34 * ============= ============== ============ ==================
37 * 0 1 0 0/0, 0/1, 1/0, 1/1
41 * 1 1 0 0/0, 0/1, 1/0, 1/1
44 * If you set MAC_ASYM_PAUSE, the user may request any combination of
45 * tx_pause and rx_pause. You do not have to support these
48 * However, you should support combinations of tx_pause and rx_pause
49 * which might be the result of autonegotation. For example, don't set
50 * MAC_SYM_PAUSE unless your device can support tx_pause and rx_pause
53 MAC_SYM_PAUSE = BIT(0),
54 MAC_ASYM_PAUSE = BIT(1),
57 MAC_10 = MAC_10HD | MAC_10FD,
60 MAC_100 = MAC_100HD | MAC_100FD,
63 MAC_1000 = MAC_1000HD | MAC_1000FD,
66 MAC_10000FD = BIT(10),
67 MAC_20000FD = BIT(11),
68 MAC_25000FD = BIT(12),
69 MAC_40000FD = BIT(13),
70 MAC_50000FD = BIT(14),
71 MAC_56000FD = BIT(15),
72 MAC_100000FD = BIT(16),
73 MAC_200000FD = BIT(17),
74 MAC_400000FD = BIT(18),
77 static inline bool phylink_autoneg_inband(unsigned int mode)
79 return mode == MLO_AN_INBAND;
83 * struct phylink_link_state - link state structure
84 * @advertising: ethtool bitmask containing advertised link modes
85 * @lp_advertising: ethtool bitmask containing link partner advertised link
87 * @interface: link &typedef phy_interface_t mode
88 * @speed: link speed, one of the SPEED_* constants.
89 * @duplex: link duplex mode, one of DUPLEX_* constants.
90 * @pause: link pause state, described by MLO_PAUSE_* constants.
91 * @rate_matching: rate matching being performed, one of the RATE_MATCH_*
92 * constants. If rate matching is taking place, then the speed/duplex of
93 * the medium link mode (@speed and @duplex) and the speed/duplex of the phy
94 * interface mode (@interface) are different.
95 * @link: true if the link is up.
96 * @an_enabled: true if autonegotiation is enabled/desired.
97 * @an_complete: true if autonegotiation has completed.
99 struct phylink_link_state {
100 __ETHTOOL_DECLARE_LINK_MODE_MASK(advertising);
101 __ETHTOOL_DECLARE_LINK_MODE_MASK(lp_advertising);
102 phy_interface_t interface;
108 unsigned int an_enabled:1;
109 unsigned int an_complete:1;
112 enum phylink_op_type {
118 * struct phylink_config - PHYLINK configuration structure
119 * @dev: a pointer to a struct device associated with the MAC
120 * @type: operation type of PHYLINK instance
121 * @legacy_pre_march2020: driver has not been updated for March 2020 updates
122 * (See commit 7cceb599d15d ("net: phylink: avoid mac_config calls")
123 * @poll_fixed_state: if true, starts link_poll,
124 * if MAC link is at %MLO_AN_FIXED mode.
125 * @ovr_an_inband: if true, override PCS to MLO_AN_INBAND
126 * @get_fixed_state: callback to execute to determine the fixed link state,
127 * if MAC link is at %MLO_AN_FIXED mode.
128 * @supported_interfaces: bitmap describing which PHY_INTERFACE_MODE_xxx
129 * are supported by the MAC/PCS.
130 * @mac_capabilities: MAC pause/speed/duplex capabilities.
132 struct phylink_config {
134 enum phylink_op_type type;
135 bool legacy_pre_march2020;
136 bool poll_fixed_state;
138 void (*get_fixed_state)(struct phylink_config *config,
139 struct phylink_link_state *state);
140 DECLARE_PHY_INTERFACE_MASK(supported_interfaces);
141 unsigned long mac_capabilities;
145 * struct phylink_mac_ops - MAC operations structure.
146 * @validate: Validate and update the link configuration.
147 * @mac_select_pcs: Select a PCS for the interface mode.
148 * @mac_pcs_get_state: Read the current link state from the hardware.
149 * @mac_prepare: prepare for a major reconfiguration of the interface.
150 * @mac_config: configure the MAC for the selected mode and state.
151 * @mac_finish: finish a major reconfiguration of the interface.
152 * @mac_an_restart: restart 802.3z BaseX autonegotiation.
153 * @mac_link_down: take the link down.
154 * @mac_link_up: allow the link to come up.
156 * The individual methods are described more fully below.
158 struct phylink_mac_ops {
159 void (*validate)(struct phylink_config *config,
160 unsigned long *supported,
161 struct phylink_link_state *state);
162 struct phylink_pcs *(*mac_select_pcs)(struct phylink_config *config,
163 phy_interface_t interface);
164 void (*mac_pcs_get_state)(struct phylink_config *config,
165 struct phylink_link_state *state);
166 int (*mac_prepare)(struct phylink_config *config, unsigned int mode,
167 phy_interface_t iface);
168 void (*mac_config)(struct phylink_config *config, unsigned int mode,
169 const struct phylink_link_state *state);
170 int (*mac_finish)(struct phylink_config *config, unsigned int mode,
171 phy_interface_t iface);
172 void (*mac_an_restart)(struct phylink_config *config);
173 void (*mac_link_down)(struct phylink_config *config, unsigned int mode,
174 phy_interface_t interface);
175 void (*mac_link_up)(struct phylink_config *config,
176 struct phy_device *phy, unsigned int mode,
177 phy_interface_t interface, int speed, int duplex,
178 bool tx_pause, bool rx_pause);
181 #if 0 /* For kernel-doc purposes only. */
183 * validate - Validate and update the link configuration
184 * @config: a pointer to a &struct phylink_config.
185 * @supported: ethtool bitmask for supported link modes.
186 * @state: a pointer to a &struct phylink_link_state.
188 * Clear bits in the @supported and @state->advertising masks that
189 * are not supportable by the MAC.
191 * Note that the PHY may be able to transform from one connection
192 * technology to another, so, eg, don't clear 1000BaseX just
193 * because the MAC is unable to BaseX mode. This is more about
194 * clearing unsupported speeds and duplex settings. The port modes
195 * should not be cleared; phylink_set_port_modes() will help with this.
197 * When @config->supported_interfaces has been set, phylink will iterate
198 * over the supported interfaces to determine the full capability of the
199 * MAC. The validation function must not print errors if @state->interface
200 * is set to an unexpected value.
202 * When @config->supported_interfaces is empty, phylink will call this
203 * function with @state->interface set to %PHY_INTERFACE_MODE_NA, and
204 * expects the MAC driver to return all supported link modes.
206 * If the @state->interface mode is not supported, then the @supported
207 * mask must be cleared.
209 void validate(struct phylink_config *config, unsigned long *supported,
210 struct phylink_link_state *state);
212 * mac_select_pcs: Select a PCS for the interface mode.
213 * @config: a pointer to a &struct phylink_config.
214 * @interface: PHY interface mode for PCS
216 * Return the &struct phylink_pcs for the specified interface mode, or
217 * NULL if none is required, or an error pointer on error.
219 * This must not modify any state. It is used to query which PCS should
220 * be used. Phylink will use this during validation to ensure that the
221 * configuration is valid, and when setting a configuration to internally
222 * set the PCS that will be used.
224 struct phylink_pcs *mac_select_pcs(struct phylink_config *config,
225 phy_interface_t interface);
228 * mac_pcs_get_state() - Read the current inband link state from the hardware
229 * @config: a pointer to a &struct phylink_config.
230 * @state: a pointer to a &struct phylink_link_state.
232 * Read the current inband link state from the MAC PCS, reporting the
233 * current speed in @state->speed, duplex mode in @state->duplex, pause
234 * mode in @state->pause using the %MLO_PAUSE_RX and %MLO_PAUSE_TX bits,
235 * negotiation completion state in @state->an_complete, and link up state
236 * in @state->link. If possible, @state->lp_advertising should also be
239 * Note: This is a legacy method. This function will not be called unless
240 * legacy_pre_march2020 is set in &struct phylink_config and there is no
243 void mac_pcs_get_state(struct phylink_config *config,
244 struct phylink_link_state *state);
247 * mac_prepare() - prepare to change the PHY interface mode
248 * @config: a pointer to a &struct phylink_config.
249 * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
250 * @iface: interface mode to switch to
252 * phylink will call this method at the beginning of a full initialisation
253 * of the link, which includes changing the interface mode or at initial
254 * startup time. It may be called for the current mode. The MAC driver
255 * should perform whatever actions are required, e.g. disabling the
258 * This will be the first call in the sequence:
262 * - possible pcs_an_restart()
265 * Returns zero on success, or negative errno on failure which will be
266 * reported to the kernel log.
268 int mac_prepare(struct phylink_config *config, unsigned int mode,
269 phy_interface_t iface);
272 * mac_config() - configure the MAC for the selected mode and state
273 * @config: a pointer to a &struct phylink_config.
274 * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
275 * @state: a pointer to a &struct phylink_link_state.
277 * Note - not all members of @state are valid. In particular,
278 * @state->lp_advertising, @state->link, @state->an_complete are never
279 * guaranteed to be correct, and so any mac_config() implementation must
280 * never reference these fields.
282 * Note: For legacy March 2020 drivers (drivers with legacy_pre_march2020 set
283 * in their &phylnk_config and which don't have a PCS), this function will be
284 * called on each link up event, and to also change the in-band advert. For
285 * non-legacy drivers, it will only be called to reconfigure the MAC for a
286 * "major" change in e.g. interface mode. It will not be called for changes
287 * in speed, duplex or pause modes or to change the in-band advertisement.
288 * In any case, it is strongly preferred that speed, duplex and pause settings
289 * are handled in the mac_link_up() method and not in this method.
291 * (this requires a rewrite - please refer to mac_link_up() for situations
292 * where the PCS and MAC are not tightly integrated.)
294 * In all negotiation modes, as defined by @mode, @state->pause indicates the
295 * pause settings which should be applied as follows. If %MLO_PAUSE_AN is not
296 * set, %MLO_PAUSE_TX and %MLO_PAUSE_RX indicate whether the MAC should send
297 * pause frames and/or act on received pause frames respectively. Otherwise,
298 * the results of in-band negotiation/status from the MAC PCS should be used
299 * to control the MAC pause mode settings.
301 * The action performed depends on the currently selected mode:
303 * %MLO_AN_FIXED, %MLO_AN_PHY:
304 * Configure for non-inband negotiation mode, where the link settings
305 * are completely communicated via mac_link_up(). The physical link
306 * protocol from the MAC is specified by @state->interface.
308 * @state->advertising may be used, but is not required.
310 * Older drivers (prior to the mac_link_up() change) may use @state->speed,
311 * @state->duplex and @state->pause to configure the MAC, but this is
312 * deprecated; such drivers should be converted to use mac_link_up().
314 * Other members of @state must be ignored.
316 * Valid state members: interface, advertising.
317 * Deprecated state members: speed, duplex, pause.
320 * place the link in an inband negotiation mode (such as 802.3z
321 * 1000base-X or Cisco SGMII mode depending on the @state->interface
322 * mode). In both cases, link state management (whether the link
323 * is up or not) is performed by the MAC, and reported via the
324 * mac_pcs_get_state() callback. Changes in link state must be made
325 * by calling phylink_mac_change().
327 * Interface mode specific details are mentioned below.
329 * If in 802.3z mode, the link speed is fixed, dependent on the
330 * @state->interface. Duplex and pause modes are negotiated via
331 * the in-band configuration word. Advertised pause modes are set
332 * according to the @state->an_enabled and @state->advertising
333 * flags. Beware of MACs which only support full duplex at gigabit
336 * If in Cisco SGMII mode, the link speed and duplex mode are passed
337 * in the serial bitstream 16-bit configuration word, and the MAC
338 * should be configured to read these bits and acknowledge the
339 * configuration word. Nothing is advertised by the MAC. The MAC is
340 * responsible for reading the configuration word and configuring
341 * itself accordingly.
343 * Valid state members: interface, an_enabled, pause, advertising.
345 * Implementations are expected to update the MAC to reflect the
346 * requested settings - i.o.w., if nothing has changed between two
347 * calls, no action is expected. If only flow control settings have
348 * changed, flow control should be updated *without* taking the link
349 * down. This "update" behaviour is critical to avoid bouncing the
352 void mac_config(struct phylink_config *config, unsigned int mode,
353 const struct phylink_link_state *state);
356 * mac_finish() - finish a to change the PHY interface mode
357 * @config: a pointer to a &struct phylink_config.
358 * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
359 * @iface: interface mode to switch to
361 * phylink will call this if it called mac_prepare() to allow the MAC to
362 * complete any necessary steps after the MAC and PCS have been configured
363 * for the @mode and @iface. E.g. a MAC driver may wish to re-enable the
364 * Serdes PHY here if it was previously disabled by mac_prepare().
366 * Returns zero on success, or negative errno on failure which will be
367 * reported to the kernel log.
369 int mac_finish(struct phylink_config *config, unsigned int mode,
370 phy_interface_t iface);
373 * mac_an_restart() - restart 802.3z BaseX autonegotiation
374 * @config: a pointer to a &struct phylink_config.
376 * Note: This is a legacy method. This function will not be called unless
377 * legacy_pre_march2020 is set in &struct phylink_config and there is no
380 void mac_an_restart(struct phylink_config *config);
383 * mac_link_down() - take the link down
384 * @config: a pointer to a &struct phylink_config.
385 * @mode: link autonegotiation mode
386 * @interface: link &typedef phy_interface_t mode
388 * If @mode is not an in-band negotiation mode (as defined by
389 * phylink_autoneg_inband()), force the link down and disable any
390 * Energy Efficient Ethernet MAC configuration. Interface type
391 * selection must be done in mac_config().
393 void mac_link_down(struct phylink_config *config, unsigned int mode,
394 phy_interface_t interface);
397 * mac_link_up() - allow the link to come up
398 * @config: a pointer to a &struct phylink_config.
399 * @phy: any attached phy
400 * @mode: link autonegotiation mode
401 * @interface: link &typedef phy_interface_t mode
403 * @duplex: link duplex
404 * @tx_pause: link transmit pause enablement status
405 * @rx_pause: link receive pause enablement status
407 * Configure the MAC for an established link.
409 * @speed, @duplex, @tx_pause and @rx_pause indicate the finalised link
410 * settings, and should be used to configure the MAC block appropriately
411 * where these settings are not automatically conveyed from the PCS block,
412 * or if in-band negotiation (as defined by phylink_autoneg_inband(@mode))
415 * Note that when 802.3z in-band negotiation is in use, it is possible
416 * that the user wishes to override the pause settings, and this should
417 * be allowed when considering the implementation of this method.
419 * If in-band negotiation mode is disabled, allow the link to come up. If
420 * @phy is non-%NULL, configure Energy Efficient Ethernet by calling
421 * phy_init_eee() and perform appropriate MAC configuration for EEE.
422 * Interface type selection must be done in mac_config().
424 void mac_link_up(struct phylink_config *config, struct phy_device *phy,
425 unsigned int mode, phy_interface_t interface,
426 int speed, int duplex, bool tx_pause, bool rx_pause);
429 struct phylink_pcs_ops;
432 * struct phylink_pcs - PHYLINK PCS instance
433 * @ops: a pointer to the &struct phylink_pcs_ops structure
434 * @poll: poll the PCS for link changes
436 * This structure is designed to be embedded within the PCS private data,
437 * and will be passed between phylink and the PCS.
440 const struct phylink_pcs_ops *ops;
445 * struct phylink_pcs_ops - MAC PCS operations structure.
446 * @pcs_validate: validate the link configuration.
447 * @pcs_get_state: read the current MAC PCS link state from the hardware.
448 * @pcs_config: configure the MAC PCS for the selected mode and state.
449 * @pcs_an_restart: restart 802.3z BaseX autonegotiation.
450 * @pcs_link_up: program the PCS for the resolved link configuration
453 struct phylink_pcs_ops {
454 int (*pcs_validate)(struct phylink_pcs *pcs, unsigned long *supported,
455 const struct phylink_link_state *state);
456 void (*pcs_get_state)(struct phylink_pcs *pcs,
457 struct phylink_link_state *state);
458 int (*pcs_config)(struct phylink_pcs *pcs, unsigned int mode,
459 phy_interface_t interface,
460 const unsigned long *advertising,
461 bool permit_pause_to_mac);
462 void (*pcs_an_restart)(struct phylink_pcs *pcs);
463 void (*pcs_link_up)(struct phylink_pcs *pcs, unsigned int mode,
464 phy_interface_t interface, int speed, int duplex);
467 #if 0 /* For kernel-doc purposes only. */
469 * pcs_validate() - validate the link configuration.
470 * @pcs: a pointer to a &struct phylink_pcs.
471 * @supported: ethtool bitmask for supported link modes.
472 * @state: a const pointer to a &struct phylink_link_state.
474 * Validate the interface mode, and advertising's autoneg bit, removing any
475 * media ethtool link modes that would not be supportable from the supported
476 * mask. Phylink will propagate the changes to the advertising mask. See the
477 * &struct phylink_mac_ops validate() method.
479 * Returns -EINVAL if the interface mode/autoneg mode is not supported.
480 * Returns non-zero positive if the link state can be supported.
482 int pcs_validate(struct phylink_pcs *pcs, unsigned long *supported,
483 const struct phylink_link_state *state);
486 * pcs_get_state() - Read the current inband link state from the hardware
487 * @pcs: a pointer to a &struct phylink_pcs.
488 * @state: a pointer to a &struct phylink_link_state.
490 * Read the current inband link state from the MAC PCS, reporting the
491 * current speed in @state->speed, duplex mode in @state->duplex, pause
492 * mode in @state->pause using the %MLO_PAUSE_RX and %MLO_PAUSE_TX bits,
493 * negotiation completion state in @state->an_complete, and link up state
494 * in @state->link. If possible, @state->lp_advertising should also be
497 * When present, this overrides mac_pcs_get_state() in &struct
500 void pcs_get_state(struct phylink_pcs *pcs,
501 struct phylink_link_state *state);
504 * pcs_config() - Configure the PCS mode and advertisement
505 * @pcs: a pointer to a &struct phylink_pcs.
506 * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
507 * @interface: interface mode to be used
508 * @advertising: adertisement ethtool link mode mask
509 * @permit_pause_to_mac: permit forwarding pause resolution to MAC
511 * Configure the PCS for the operating mode, the interface mode, and set
512 * the advertisement mask. @permit_pause_to_mac indicates whether the
513 * hardware may forward the pause mode resolution to the MAC.
515 * When operating in %MLO_AN_INBAND, inband should always be enabled,
516 * otherwise inband should be disabled.
518 * For SGMII, there is no advertisement from the MAC side, the PCS should
519 * be programmed to acknowledge the inband word from the PHY.
521 * For 1000BASE-X, the advertisement should be programmed into the PCS.
523 * For most 10GBASE-R, there is no advertisement.
525 int pcs_config(struct phylink_pcs *pcs, unsigned int mode,
526 phy_interface_t interface, const unsigned long *advertising,
527 bool permit_pause_to_mac);
530 * pcs_an_restart() - restart 802.3z BaseX autonegotiation
531 * @pcs: a pointer to a &struct phylink_pcs.
533 * When PCS ops are present, this overrides mac_an_restart() in &struct
536 void pcs_an_restart(struct phylink_pcs *pcs);
539 * pcs_link_up() - program the PCS for the resolved link configuration
540 * @pcs: a pointer to a &struct phylink_pcs.
541 * @mode: link autonegotiation mode
542 * @interface: link &typedef phy_interface_t mode
544 * @duplex: link duplex
546 * This call will be made just before mac_link_up() to inform the PCS of
547 * the resolved link parameters. For example, a PCS operating in SGMII
548 * mode without in-band AN needs to be manually configured for the link
549 * and duplex setting. Otherwise, this should be a no-op.
551 void pcs_link_up(struct phylink_pcs *pcs, unsigned int mode,
552 phy_interface_t interface, int speed, int duplex);
555 void phylink_caps_to_linkmodes(unsigned long *linkmodes, unsigned long caps);
556 unsigned long phylink_get_capabilities(phy_interface_t interface,
557 unsigned long mac_capabilities,
559 void phylink_generic_validate(struct phylink_config *config,
560 unsigned long *supported,
561 struct phylink_link_state *state);
563 struct phylink *phylink_create(struct phylink_config *, struct fwnode_handle *,
564 phy_interface_t iface,
565 const struct phylink_mac_ops *mac_ops);
566 void phylink_destroy(struct phylink *);
568 int phylink_connect_phy(struct phylink *, struct phy_device *);
569 int phylink_of_phy_connect(struct phylink *, struct device_node *, u32 flags);
570 int phylink_fwnode_phy_connect(struct phylink *pl,
571 struct fwnode_handle *fwnode,
573 void phylink_disconnect_phy(struct phylink *);
575 void phylink_mac_change(struct phylink *, bool up);
577 void phylink_start(struct phylink *);
578 void phylink_stop(struct phylink *);
580 void phylink_suspend(struct phylink *pl, bool mac_wol);
581 void phylink_resume(struct phylink *pl);
583 void phylink_ethtool_get_wol(struct phylink *, struct ethtool_wolinfo *);
584 int phylink_ethtool_set_wol(struct phylink *, struct ethtool_wolinfo *);
586 int phylink_ethtool_ksettings_get(struct phylink *,
587 struct ethtool_link_ksettings *);
588 int phylink_ethtool_ksettings_set(struct phylink *,
589 const struct ethtool_link_ksettings *);
590 int phylink_ethtool_nway_reset(struct phylink *);
591 void phylink_ethtool_get_pauseparam(struct phylink *,
592 struct ethtool_pauseparam *);
593 int phylink_ethtool_set_pauseparam(struct phylink *,
594 struct ethtool_pauseparam *);
595 int phylink_get_eee_err(struct phylink *);
596 int phylink_init_eee(struct phylink *, bool);
597 int phylink_ethtool_get_eee(struct phylink *, struct ethtool_eee *);
598 int phylink_ethtool_set_eee(struct phylink *, struct ethtool_eee *);
599 int phylink_mii_ioctl(struct phylink *, struct ifreq *, int);
600 int phylink_speed_down(struct phylink *pl, bool sync);
601 int phylink_speed_up(struct phylink *pl);
603 #define phylink_zero(bm) \
604 bitmap_zero(bm, __ETHTOOL_LINK_MODE_MASK_NBITS)
605 #define __phylink_do_bit(op, bm, mode) \
606 op(ETHTOOL_LINK_MODE_ ## mode ## _BIT, bm)
608 #define phylink_set(bm, mode) __phylink_do_bit(__set_bit, bm, mode)
609 #define phylink_clear(bm, mode) __phylink_do_bit(__clear_bit, bm, mode)
610 #define phylink_test(bm, mode) __phylink_do_bit(test_bit, bm, mode)
612 void phylink_set_port_modes(unsigned long *bits);
614 void phylink_mii_c22_pcs_decode_state(struct phylink_link_state *state,
616 void phylink_mii_c22_pcs_get_state(struct mdio_device *pcs,
617 struct phylink_link_state *state);
618 int phylink_mii_c22_pcs_encode_advertisement(phy_interface_t interface,
619 const unsigned long *advertising);
620 int phylink_mii_c22_pcs_config(struct mdio_device *pcs, unsigned int mode,
621 phy_interface_t interface,
622 const unsigned long *advertising);
623 void phylink_mii_c22_pcs_an_restart(struct mdio_device *pcs);
625 void phylink_mii_c45_pcs_get_state(struct mdio_device *pcs,
626 struct phylink_link_state *state);
628 void phylink_decode_usxgmii_word(struct phylink_link_state *state,