1 // SPDX-License-Identifier: GPL-2.0
4 * Texas Instruments AM35x "glue layer"
6 * Copyright (c) 2010, by Texas Instruments
8 * Based on the DA8xx "glue layer" code.
9 * Copyright (c) 2008-2009, MontaVista Software, Inc. <source@mvista.com>
11 * This file is part of the Inventra Controller Driver for Linux.
14 #include <linux/module.h>
15 #include <linux/clk.h>
16 #include <linux/err.h>
18 #include <linux/platform_device.h>
19 #include <linux/dma-mapping.h>
20 #include <linux/usb/usb_phy_generic.h>
21 #include <linux/platform_data/usb-omap.h>
23 #include "musb_core.h"
26 * AM35x specific definitions
28 /* USB 2.0 OTG module registers */
29 #define USB_REVISION_REG 0x00
30 #define USB_CTRL_REG 0x04
31 #define USB_STAT_REG 0x08
32 #define USB_EMULATION_REG 0x0c
34 #define USB_AUTOREQ_REG 0x14
35 #define USB_SRP_FIX_TIME_REG 0x18
36 #define USB_TEARDOWN_REG 0x1c
37 #define EP_INTR_SRC_REG 0x20
38 #define EP_INTR_SRC_SET_REG 0x24
39 #define EP_INTR_SRC_CLEAR_REG 0x28
40 #define EP_INTR_MASK_REG 0x2c
41 #define EP_INTR_MASK_SET_REG 0x30
42 #define EP_INTR_MASK_CLEAR_REG 0x34
43 #define EP_INTR_SRC_MASKED_REG 0x38
44 #define CORE_INTR_SRC_REG 0x40
45 #define CORE_INTR_SRC_SET_REG 0x44
46 #define CORE_INTR_SRC_CLEAR_REG 0x48
47 #define CORE_INTR_MASK_REG 0x4c
48 #define CORE_INTR_MASK_SET_REG 0x50
49 #define CORE_INTR_MASK_CLEAR_REG 0x54
50 #define CORE_INTR_SRC_MASKED_REG 0x58
52 #define USB_END_OF_INTR_REG 0x60
54 /* Control register bits */
55 #define AM35X_SOFT_RESET_MASK 1
57 /* USB interrupt register bits */
58 #define AM35X_INTR_USB_SHIFT 16
59 #define AM35X_INTR_USB_MASK (0x1ff << AM35X_INTR_USB_SHIFT)
60 #define AM35X_INTR_DRVVBUS 0x100
61 #define AM35X_INTR_RX_SHIFT 16
62 #define AM35X_INTR_TX_SHIFT 0
63 #define AM35X_TX_EP_MASK 0xffff /* EP0 + 15 Tx EPs */
64 #define AM35X_RX_EP_MASK 0xfffe /* 15 Rx EPs */
65 #define AM35X_TX_INTR_MASK (AM35X_TX_EP_MASK << AM35X_INTR_TX_SHIFT)
66 #define AM35X_RX_INTR_MASK (AM35X_RX_EP_MASK << AM35X_INTR_RX_SHIFT)
68 #define USB_MENTOR_CORE_OFFSET 0x400
72 struct platform_device *musb;
73 struct platform_device *phy;
79 * am35x_musb_enable - enable interrupts
81 static void am35x_musb_enable(struct musb *musb)
83 void __iomem *reg_base = musb->ctrl_base;
86 /* Workaround: setup IRQs through both register sets. */
87 epmask = ((musb->epmask & AM35X_TX_EP_MASK) << AM35X_INTR_TX_SHIFT) |
88 ((musb->epmask & AM35X_RX_EP_MASK) << AM35X_INTR_RX_SHIFT);
90 musb_writel(reg_base, EP_INTR_MASK_SET_REG, epmask);
91 musb_writel(reg_base, CORE_INTR_MASK_SET_REG, AM35X_INTR_USB_MASK);
93 /* Force the DRVVBUS IRQ so we can start polling for ID change. */
94 musb_writel(reg_base, CORE_INTR_SRC_SET_REG,
95 AM35X_INTR_DRVVBUS << AM35X_INTR_USB_SHIFT);
99 * am35x_musb_disable - disable HDRC and flush interrupts
101 static void am35x_musb_disable(struct musb *musb)
103 void __iomem *reg_base = musb->ctrl_base;
105 musb_writel(reg_base, CORE_INTR_MASK_CLEAR_REG, AM35X_INTR_USB_MASK);
106 musb_writel(reg_base, EP_INTR_MASK_CLEAR_REG,
107 AM35X_TX_INTR_MASK | AM35X_RX_INTR_MASK);
108 musb_writel(reg_base, USB_END_OF_INTR_REG, 0);
111 #define portstate(stmt) stmt
113 static void am35x_musb_set_vbus(struct musb *musb, int is_on)
115 WARN_ON(is_on && is_peripheral_active(musb));
118 #define POLL_SECONDS 2
120 static void otg_timer(struct timer_list *t)
122 struct musb *musb = from_timer(musb, t, dev_timer);
123 void __iomem *mregs = musb->mregs;
128 * We poll because AM35x's won't expose several OTG-critical
129 * status change events (from the transceiver) otherwise.
131 devctl = musb_readb(mregs, MUSB_DEVCTL);
132 dev_dbg(musb->controller, "Poll devctl %02x (%s)\n", devctl,
133 usb_otg_state_string(musb->xceiv->otg->state));
135 spin_lock_irqsave(&musb->lock, flags);
136 switch (musb->xceiv->otg->state) {
137 case OTG_STATE_A_WAIT_BCON:
138 devctl &= ~MUSB_DEVCTL_SESSION;
139 musb_writeb(musb->mregs, MUSB_DEVCTL, devctl);
141 devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
142 if (devctl & MUSB_DEVCTL_BDEVICE) {
143 musb->xceiv->otg->state = OTG_STATE_B_IDLE;
146 musb->xceiv->otg->state = OTG_STATE_A_IDLE;
150 case OTG_STATE_A_WAIT_VFALL:
151 musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
152 musb_writel(musb->ctrl_base, CORE_INTR_SRC_SET_REG,
153 MUSB_INTR_VBUSERROR << AM35X_INTR_USB_SHIFT);
155 case OTG_STATE_B_IDLE:
156 devctl = musb_readb(mregs, MUSB_DEVCTL);
157 if (devctl & MUSB_DEVCTL_BDEVICE)
158 mod_timer(&musb->dev_timer, jiffies + POLL_SECONDS * HZ);
160 musb->xceiv->otg->state = OTG_STATE_A_IDLE;
165 spin_unlock_irqrestore(&musb->lock, flags);
168 static void am35x_musb_try_idle(struct musb *musb, unsigned long timeout)
170 static unsigned long last_timer;
173 timeout = jiffies + msecs_to_jiffies(3);
175 /* Never idle if active, or when VBUS timeout is not set as host */
176 if (musb->is_active || (musb->a_wait_bcon == 0 &&
177 musb->xceiv->otg->state == OTG_STATE_A_WAIT_BCON)) {
178 dev_dbg(musb->controller, "%s active, deleting timer\n",
179 usb_otg_state_string(musb->xceiv->otg->state));
180 del_timer(&musb->dev_timer);
181 last_timer = jiffies;
185 if (time_after(last_timer, timeout) && timer_pending(&musb->dev_timer)) {
186 dev_dbg(musb->controller, "Longer idle timer already pending, ignoring...\n");
189 last_timer = timeout;
191 dev_dbg(musb->controller, "%s inactive, starting idle timer for %u ms\n",
192 usb_otg_state_string(musb->xceiv->otg->state),
193 jiffies_to_msecs(timeout - jiffies));
194 mod_timer(&musb->dev_timer, timeout);
197 static irqreturn_t am35x_musb_interrupt(int irq, void *hci)
199 struct musb *musb = hci;
200 void __iomem *reg_base = musb->ctrl_base;
201 struct device *dev = musb->controller;
202 struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
203 struct omap_musb_board_data *data = plat->board_data;
204 struct usb_otg *otg = musb->xceiv->otg;
206 irqreturn_t ret = IRQ_NONE;
209 spin_lock_irqsave(&musb->lock, flags);
211 /* Get endpoint interrupts */
212 epintr = musb_readl(reg_base, EP_INTR_SRC_MASKED_REG);
215 musb_writel(reg_base, EP_INTR_SRC_CLEAR_REG, epintr);
218 (epintr & AM35X_RX_INTR_MASK) >> AM35X_INTR_RX_SHIFT;
220 (epintr & AM35X_TX_INTR_MASK) >> AM35X_INTR_TX_SHIFT;
223 /* Get usb core interrupts */
224 usbintr = musb_readl(reg_base, CORE_INTR_SRC_MASKED_REG);
225 if (!usbintr && !epintr)
229 musb_writel(reg_base, CORE_INTR_SRC_CLEAR_REG, usbintr);
232 (usbintr & AM35X_INTR_USB_MASK) >> AM35X_INTR_USB_SHIFT;
235 * DRVVBUS IRQs are the only proxy we have (a very poor one!) for
236 * AM35x's missing ID change IRQ. We need an ID change IRQ to
237 * switch appropriately between halves of the OTG state machine.
238 * Managing DEVCTL.SESSION per Mentor docs requires that we know its
239 * value but DEVCTL.BDEVICE is invalid without DEVCTL.SESSION set.
240 * Also, DRVVBUS pulses for SRP (but not at 5V) ...
242 if (usbintr & (AM35X_INTR_DRVVBUS << AM35X_INTR_USB_SHIFT)) {
243 int drvvbus = musb_readl(reg_base, USB_STAT_REG);
244 void __iomem *mregs = musb->mregs;
245 u8 devctl = musb_readb(mregs, MUSB_DEVCTL);
248 err = musb->int_usb & MUSB_INTR_VBUSERROR;
251 * The Mentor core doesn't debounce VBUS as needed
252 * to cope with device connect current spikes. This
253 * means it's not uncommon for bus-powered devices
254 * to get VBUS errors during enumeration.
256 * This is a workaround, but newer RTL from Mentor
257 * seems to allow a better one: "re"-starting sessions
258 * without waiting for VBUS to stop registering in
261 musb->int_usb &= ~MUSB_INTR_VBUSERROR;
262 musb->xceiv->otg->state = OTG_STATE_A_WAIT_VFALL;
263 mod_timer(&musb->dev_timer, jiffies + POLL_SECONDS * HZ);
264 WARNING("VBUS error workaround (delay coming)\n");
265 } else if (drvvbus) {
268 musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
269 portstate(musb->port1_status |= USB_PORT_STAT_POWER);
270 del_timer(&musb->dev_timer);
275 musb->xceiv->otg->state = OTG_STATE_B_IDLE;
276 portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
279 /* NOTE: this must complete power-on within 100 ms. */
280 dev_dbg(musb->controller, "VBUS %s (%s)%s, devctl %02x\n",
281 drvvbus ? "on" : "off",
282 usb_otg_state_string(musb->xceiv->otg->state),
288 /* Drop spurious RX and TX if device is disconnected */
289 if (musb->int_usb & MUSB_INTR_DISCONNECT) {
294 if (musb->int_tx || musb->int_rx || musb->int_usb)
295 ret |= musb_interrupt(musb);
298 /* EOI needs to be written for the IRQ to be re-asserted. */
299 if (ret == IRQ_HANDLED || epintr || usbintr) {
300 /* clear level interrupt */
304 musb_writel(reg_base, USB_END_OF_INTR_REG, 0);
307 /* Poll for ID change */
308 if (musb->xceiv->otg->state == OTG_STATE_B_IDLE)
309 mod_timer(&musb->dev_timer, jiffies + POLL_SECONDS * HZ);
311 spin_unlock_irqrestore(&musb->lock, flags);
316 static int am35x_musb_set_mode(struct musb *musb, u8 musb_mode)
318 struct device *dev = musb->controller;
319 struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
320 struct omap_musb_board_data *data = plat->board_data;
324 data->set_mode(musb_mode);
331 static int am35x_musb_init(struct musb *musb)
333 struct device *dev = musb->controller;
334 struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
335 struct omap_musb_board_data *data = plat->board_data;
336 void __iomem *reg_base = musb->ctrl_base;
339 musb->mregs += USB_MENTOR_CORE_OFFSET;
341 /* Returns zero if e.g. not clocked */
342 rev = musb_readl(reg_base, USB_REVISION_REG);
346 musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
347 if (IS_ERR_OR_NULL(musb->xceiv))
348 return -EPROBE_DEFER;
350 timer_setup(&musb->dev_timer, otg_timer, 0);
356 /* Reset the controller */
357 musb_writel(reg_base, USB_CTRL_REG, AM35X_SOFT_RESET_MASK);
359 /* Start the on-chip PHY and its PLL. */
360 if (data->set_phy_power)
361 data->set_phy_power(1);
365 musb->isr = am35x_musb_interrupt;
367 /* clear level interrupt */
374 static int am35x_musb_exit(struct musb *musb)
376 struct device *dev = musb->controller;
377 struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
378 struct omap_musb_board_data *data = plat->board_data;
380 del_timer_sync(&musb->dev_timer);
382 /* Shutdown the on-chip PHY and its PLL. */
383 if (data->set_phy_power)
384 data->set_phy_power(0);
386 usb_put_phy(musb->xceiv);
391 /* AM35x supports only 32bit read operation */
392 static void am35x_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst)
394 void __iomem *fifo = hw_ep->fifo;
398 /* Read for 32bit-aligned destination address */
399 if (likely((0x03 & (unsigned long) dst) == 0) && len >= 4) {
400 readsl(fifo, dst, len >> 2);
405 * Now read the remaining 1 to 3 byte or complete length if
409 for (i = 0; i < (len >> 2); i++) {
410 *(u32 *) dst = musb_readl(fifo, 0);
416 val = musb_readl(fifo, 0);
417 memcpy(dst, &val, len);
421 static const struct musb_platform_ops am35x_ops = {
422 .quirks = MUSB_DMA_INVENTRA | MUSB_INDEXED_EP,
423 .init = am35x_musb_init,
424 .exit = am35x_musb_exit,
426 .read_fifo = am35x_read_fifo,
427 #ifdef CONFIG_USB_INVENTRA_DMA
428 .dma_init = musbhs_dma_controller_create,
429 .dma_exit = musbhs_dma_controller_destroy,
431 .enable = am35x_musb_enable,
432 .disable = am35x_musb_disable,
434 .set_mode = am35x_musb_set_mode,
435 .try_idle = am35x_musb_try_idle,
437 .set_vbus = am35x_musb_set_vbus,
440 static const struct platform_device_info am35x_dev_info = {
442 .id = PLATFORM_DEVID_AUTO,
443 .dma_mask = DMA_BIT_MASK(32),
446 static int am35x_probe(struct platform_device *pdev)
448 struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev);
449 struct platform_device *musb;
450 struct am35x_glue *glue;
451 struct platform_device_info pinfo;
457 glue = kzalloc(sizeof(*glue), GFP_KERNEL);
461 phy_clk = clk_get(&pdev->dev, "fck");
462 if (IS_ERR(phy_clk)) {
463 dev_err(&pdev->dev, "failed to get PHY clock\n");
464 ret = PTR_ERR(phy_clk);
468 clk = clk_get(&pdev->dev, "ick");
470 dev_err(&pdev->dev, "failed to get clock\n");
475 ret = clk_enable(phy_clk);
477 dev_err(&pdev->dev, "failed to enable PHY clock\n");
481 ret = clk_enable(clk);
483 dev_err(&pdev->dev, "failed to enable clock\n");
487 glue->dev = &pdev->dev;
488 glue->phy_clk = phy_clk;
491 pdata->platform_ops = &am35x_ops;
493 glue->phy = usb_phy_generic_register();
494 if (IS_ERR(glue->phy)) {
495 ret = PTR_ERR(glue->phy);
498 platform_set_drvdata(pdev, glue);
500 pinfo = am35x_dev_info;
501 pinfo.parent = &pdev->dev;
502 pinfo.res = pdev->resource;
503 pinfo.num_res = pdev->num_resources;
505 pinfo.size_data = sizeof(*pdata);
507 glue->musb = musb = platform_device_register_full(&pinfo);
510 dev_err(&pdev->dev, "failed to register musb device: %d\n", ret);
517 usb_phy_generic_unregister(glue->phy);
523 clk_disable(phy_clk);
538 static int am35x_remove(struct platform_device *pdev)
540 struct am35x_glue *glue = platform_get_drvdata(pdev);
542 platform_device_unregister(glue->musb);
543 usb_phy_generic_unregister(glue->phy);
544 clk_disable(glue->clk);
545 clk_disable(glue->phy_clk);
547 clk_put(glue->phy_clk);
553 #ifdef CONFIG_PM_SLEEP
554 static int am35x_suspend(struct device *dev)
556 struct am35x_glue *glue = dev_get_drvdata(dev);
557 struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
558 struct omap_musb_board_data *data = plat->board_data;
560 /* Shutdown the on-chip PHY and its PLL. */
561 if (data->set_phy_power)
562 data->set_phy_power(0);
564 clk_disable(glue->phy_clk);
565 clk_disable(glue->clk);
570 static int am35x_resume(struct device *dev)
572 struct am35x_glue *glue = dev_get_drvdata(dev);
573 struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
574 struct omap_musb_board_data *data = plat->board_data;
577 /* Start the on-chip PHY and its PLL. */
578 if (data->set_phy_power)
579 data->set_phy_power(1);
581 ret = clk_enable(glue->phy_clk);
583 dev_err(dev, "failed to enable PHY clock\n");
587 ret = clk_enable(glue->clk);
589 dev_err(dev, "failed to enable clock\n");
597 static SIMPLE_DEV_PM_OPS(am35x_pm_ops, am35x_suspend, am35x_resume);
599 static struct platform_driver am35x_driver = {
600 .probe = am35x_probe,
601 .remove = am35x_remove,
603 .name = "musb-am35x",
608 MODULE_DESCRIPTION("AM35x MUSB Glue Layer");
609 MODULE_AUTHOR("Ajay Kumar Gupta <ajay.gupta@ti.com>");
610 MODULE_LICENSE("GPL v2");
611 module_platform_driver(am35x_driver);