1 /* SPDX-License-Identifier: GPL-2.0 */
2 /* ///////////////////////////////////////////////////////////////////////// */
4 /* Copyright (c) Atmel Corporation. All rights reserved. */
6 /* Module Name: wilc_wlan_if.h */
9 /* ///////////////////////////////////////////////////////////////////////// */
11 #ifndef WILC_WLAN_IF_H
12 #define WILC_WLAN_IF_H
14 #include <linux/netdevice.h>
16 /********************************************
18 * Host Interface Defines
20 ********************************************/
23 #define HIF_SPI BIT(0)
24 #define HIF_SDIO_GPIO_IRQ BIT(2)
26 /********************************************
28 * Wlan Interface Defines
30 ********************************************/
51 #define WILC_MAC_INDICATE_STATUS 0x1
52 #define WILC_MAC_STATUS_INIT -1
53 #define WILC_MAC_STATUS_READY 0
54 #define WILC_MAC_STATUS_CONNECT 1
56 #define WILC_MAC_INDICATE_SCAN 0x2
58 struct tx_complete_data {
65 typedef void (*wilc_tx_complete_func_t)(void *, int);
67 #define WILC_TX_ERR_NO_BUF (-2)
69 /********************************************
71 * Wlan Configuration ID
73 ********************************************/
74 #define WILC_MULTICAST_TABLE_SIZE 8
75 #define MAX_SSID_LEN 33
76 #define MAX_RATES_SUPPORTED 12
80 EXT_SUPP_RATES_IE = 50,
81 HT_CAPABILITY_IE = 45,
111 B_ONLY_MODE = 0, /* 1, 2 M, otherwise 5, 11 M */
112 G_ONLY_MODE, /* 6,12,24 otherwise 9,18,36,48,54 */
113 G_MIXED_11B_1_MODE, /* 1,2,5.5,11 otherwise all on */
114 G_MIXED_11B_2_MODE, /* 1,2,5,11,6,12,24 otherwise all on */
115 } G_OPERATING_MODE_T;
118 G_SHORT_PREAMBLE = 0, /* Short Preamble */
119 G_LONG_PREAMBLE = 1, /* Long Preamble */
120 G_AUTO_PREAMBLE = 2, /* Auto Preamble Selection */
123 #define MAC_CONNECTED 1
124 #define MAC_DISCONNECTED 0
126 #define SCAN_DONE TRUE
142 CHIP_SLEEPING_AUTO = 1,
143 CHIP_SLEEPING_MANUAL = 2
148 ACQUIRE_AND_WAKEUP = 1,
153 RELEASE_ALLOW_SLEEP = 1,
162 WPA_AES_TKIP = 0x69, /* Aes or Tkip */
165 WPA2_AES_TKIP = 0x71, /* Aes or Tkip */
177 SITE_SURVEY_ALL_CH = 1,
197 } RSNA_REKEY_POLICY_T;
201 FILTER_AP_ONLY = 0x01,
202 FILTER_STA_ONLY = 0x02
203 } SCAN_CLASS_FITLER_T;
206 PRI_HIGH_RSSI = 0x00,
212 CH_FILTER_OFF = 0x00,
217 AUTO_PROT = 0, /* Auto */
218 NO_PROT, /* Do not use any protection */
219 ERP_PROT, /* Protect all ERP frame exchanges */
220 HT_PROT, /* Protect all HT frame exchanges */
221 GF_PROT, /* Protect all GF frame exchanges */
222 } N_PROTECTION_MODE_T;
227 } G_PROTECTION_MODE_T;
232 HT_ONLY_20_40MHZ_MODE,
233 } N_OPERATING_MODE_T;
239 DETECT_PROTECT_REPORT = 3,
240 } N_OBSS_DETECTION_T;
243 RTS_CTS_NONHT_PROT = 0, /* RTS-CTS at non-HT rate */
244 FIRST_FRAME_NONHT_PROT, /* First frame at non-HT rate */
245 LSIG_TXOP_PROT, /* LSIG TXOP Protection */
246 FIRST_FRAME_MIXED_PROT, /* First frame at Mixed format */
247 } N_PROTECTION_TYPE_T;
252 MIMO_MODE = 3, /* power save disable */
274 WID_TYPE_FORCE_32BIT = 0xFFFFFFFF
289 * -----------------------------------------------------------
290 * Configuration : Infrastructure Independent Access Point
291 * Values to set : 0 1 2
292 * -----------------------------------------------------------
294 WID_BSS_TYPE = 0x0000,
298 * -----------------------------------------------------------
299 * Configuration : 1 2 5.5 11 6 9 12 18 24 36 48 54
300 * Values to set : 1 2 5 11 6 9 12 18 24 36 48 54
301 * -----------------------------------------------------------
303 WID_CURRENT_TX_RATE = 0x0001,
307 * -----------------------------------------------------------
308 * Configuration(g) : 1 2 3 4 5 6 7 8 9 10 11 12 13 14
309 * Values to set : 1 2 3 4 5 6 7 8 9 10 11 12 13 14
310 * -----------------------------------------------------------
312 WID_CURRENT_CHANNEL = 0x0002,
316 * -----------------------------------------------------------
317 * Configuration : short long Auto
318 * Values to set : 0 1 2
319 * -----------------------------------------------------------
321 WID_PREAMBLE = 0x0003,
324 * 11g operating mode (ignored if 11g not present)
325 * -----------------------------------------------------------
326 * Configuration : HighPerf Compat(RSet #1) Compat(RSet #2)
327 * Values to set : 1 2 3
328 * -----------------------------------------------------------
330 WID_11G_OPERATING_MODE = 0x0004,
333 * Mac status (response only)
334 * -----------------------------------------------------------
335 * Configuration : disconnect connect
336 * Values to get : 0 1
337 * -----------------------------------------------------------
343 * -----------------------------------------------------------
344 * Configuration : Passive Scanning Active Scanning
345 * Values to set : 0 1
346 * -----------------------------------------------------------
348 WID_SCAN_TYPE = 0x0007,
351 * Key Id (WEP default key Id)
352 * -----------------------------------------------------------
353 * Configuration : Any value between 0 to 3
354 * Values to set : Same value. Default is 0
355 * -----------------------------------------------------------
361 * -----------------------------------------------------------
362 * Configuration : QoS Disable WMM Enable
363 * Values to set : 0 1
364 * -----------------------------------------------------------
366 WID_QOS_ENABLE = 0x000A,
370 * -----------------------------------------------------------
371 * Configuration : NO_POWERSAVE MIN_POWERSAVE MAX_POWERSAVE
372 * Values to set : 0 1 2
373 * -----------------------------------------------------------
375 WID_POWER_MANAGEMENT = 0x000B,
378 * WEP/802 11I Configuration
379 * -----------------------------------------------------------
380 * Configuration:Disable WP40 WP104 WPA-AES WPA-TKIP RSN-AES RSN-TKIP
381 * Values (0x) : 00 03 07 29 49 31 51
382 * Configuration:WPA-AES+TKIP RSN-AES+TKIP
383 * Values (0x) : 69 71
384 * -----------------------------------------------------------
386 WID_11I_MODE = 0x000C,
389 * WEP Configuration: Used in BSS STA mode only when WEP is enabled
390 * -----------------------------------------------------------
391 * Configuration : Open System Shared Key Any Type | 802.1x Auth
392 * Values (0x) : 01 02 03 | BIT2
393 * -----------------------------------------------------------
395 WID_AUTH_TYPE = 0x000D,
399 * -----------------------------------------------------------
400 * Configuration : Values to set
401 * Survey 1 Channel : 0
402 * survey all Channels : 1
403 * Disable Site Survey : 2
404 * -----------------------------------------------------------
406 WID_SITE_SURVEY = 0x000E,
410 * -----------------------------------------------------------
411 * Configuration : Any value between 1 to 255
412 * Values to set : Same value. Default is 3
413 * -----------------------------------------------------------
415 WID_LISTEN_INTERVAL = 0x000F,
419 * -----------------------------------------------------------
420 * Configuration : Any value between 1 to 255
421 * Values to set : Same value. Default is 3
422 * -----------------------------------------------------------
424 WID_DTIM_PERIOD = 0x0010,
428 * -----------------------------------------------------------
429 * Configuration : Normal Ack No Ack
430 * Values to set : 0 1
431 * -----------------------------------------------------------
433 WID_ACK_POLICY = 0x0011,
436 * Reset MAC (Set only)
437 * -----------------------------------------------------------
438 * Configuration : Don't Reset Reset No Request
439 * Values to set : 0 1 2
440 * -----------------------------------------------------------
445 * Broadcast SSID Option: Setting this will adhere to "" SSID element
446 * -----------------------------------------------------------
447 * Configuration : Enable Disable
448 * Values to set : 1 0
449 * -----------------------------------------------------------
451 WID_BCAST_SSID = 0x0015,
454 * Disconnect (Station)
455 * -----------------------------------------------------------
456 * Configuration : Association ID
457 * Values to set : Association ID
458 * -----------------------------------------------------------
460 WID_DISCONNECT = 0x0016,
464 * -----------------------------------------------------------
465 * Configuration : Sets TX Power (Higher the value greater the power)
466 * Values to set : Any value between 0 and 63 (inclusive Default 48)
467 * -----------------------------------------------------------
469 WID_TX_POWER_LEVEL_11A = 0x0018,
472 * Group Key Update Policy Selection
473 * -----------------------------------------------------------
474 * Configuration : Disabled timeBased packetBased timePacketBased
475 * Values to set : 1 2 3 4
476 * -----------------------------------------------------------
478 WID_REKEY_POLICY = 0x0019,
482 * -----------------------------------------------------------
483 * Configuration : Disallow Short Slot Allow Short Slot
484 * (Enable Only Long Slot) (Enable Short Slot if applicable)
485 * Values to set : 0 1
486 * -----------------------------------------------------------
488 WID_SHORT_SLOT_ALLOWED = 0x001A,
490 WID_PHY_ACTIVE_REG = 0x001B,
494 * -----------------------------------------------------------
495 * Configuration : Sets TX Power (Higher the value greater the power)
496 * Values to set : Any value between 0 and 63 (inclusive Default 48)
497 * -----------------------------------------------------------
499 WID_TX_POWER_LEVEL_11B = 0x001D,
503 * -----------------------------------------------------------
504 * Configuration : Request default scan
506 * -----------------------------------------------------------
508 WID_START_SCAN_REQ = 0x001E,
512 * -----------------------------------------------------------
514 * Values to get : Rssi value
515 * -----------------------------------------------------------
521 * -----------------------------------------------------------
522 * Configuration : Request to join
523 * Values to set : index of scan result
524 * -----------------------------------------------------------
526 WID_JOIN_REQ = 0x0020,
528 WID_LINKSPEED = 0x0026,
531 * Enable User Control of TX Power
532 * -----------------------------------------------------------
533 * Configuration : Disable Enable
534 * Values to set : 0 1
535 * -----------------------------------------------------------
537 WID_USER_CONTROL_ON_TX_POWER = 0x0027,
539 WID_MEMORY_ACCESS_8BIT = 0x0029,
542 * Enable Auto RX Sensitivity feature
543 * -----------------------------------------------------------
544 * Configuration : Disable Enable
545 * Values to set : 0 1
546 * -----------------------------------------------------------
548 WID_AUTO_RX_SENSITIVITY = 0x0032,
551 * Receive Buffer Based Ack
552 * -----------------------------------------------------------
553 * Configuration : Disable Enable
554 * Values to set : 0 1
555 * -----------------------------------------------------------
557 WID_DATAFLOW_CONTROL = 0x0033,
561 * -----------------------------------------------------------
562 * Configuration : Class No filter AP only Station Only
563 * Values to set : 0 1 2
564 * Configuration : Priority High Rssi Low Rssi Detect
565 * Values to set : 0 0x4 0x0
566 * Configuration : Channel filter off filter on
567 * Values to set : 0 0x10
568 * -----------------------------------------------------------
570 WID_SCAN_FILTER = 0x0036,
573 * Link Loss Threshold (measure in the beacon period)
574 * -----------------------------------------------------------
575 * Configuration : Any value between 10 and 254(Set to 255 disable)
576 * Values to set : Same value. Default is 10
577 * -----------------------------------------------------------
579 WID_LINK_LOSS_THRESHOLD = 0x0037,
581 WID_ABORT_RUNNING_SCAN = 0x003E,
583 /* NMAC Character WID list */
584 WID_WPS_START = 0x0043,
587 * Protection mode for MAC
588 * -----------------------------------------------------------
589 * Configuration : Auto No protection ERP HT GF
590 * Values to set : 0 1 2 3 4
591 * -----------------------------------------------------------
593 WID_11N_PROT_MECH = 0x0080,
596 * ERP Protection type for MAC
597 * -----------------------------------------------------------
598 * Configuration : Self-CTS RTS-CTS
599 * Values to set : 0 1
600 * -----------------------------------------------------------
602 WID_11N_ERP_PROT_TYPE = 0x0081,
606 * -----------------------------------------------------------
607 * Configuration : HT Enable HT Disable
608 * Values to set : 1 0
609 * -----------------------------------------------------------
611 WID_11N_ENABLE = 0x0082,
614 * 11n Operating mode (Note that 11g operating mode will also be
615 * used in addition to this, if this is set to HT Mixed mode)
616 * -----------------------------------------------------------
617 * Configuration : HT Mixed HT Only-20MHz HT Only-20/40MHz
618 * Values to set : 1 2 3
619 * -----------------------------------------------------------
621 WID_11N_OPERATING_MODE = 0x0083,
624 * 11n OBSS non-HT STA Detection flag
625 * -----------------------------------------------------------
626 * Configuration : Do not detect
628 * Configuration : Detect, do not protect or report
630 * Configuration : Detect, protect and do not report
632 * Configuration : Detect, protect and report to other BSS
634 * -----------------------------------------------------------
636 WID_11N_OBSS_NONHT_DETECTION = 0x0084,
639 * 11n HT Protection Type
640 * -----------------------------------------------------------
641 * Configuration : RTS-CTS First Frame Exchange at non-HT-rate
642 * Values to set : 0 1
643 * Configuration : LSIG TXOP First Frame Exchange in Mixed Fmt
644 * Values to set : 2 3
645 * -----------------------------------------------------------
647 WID_11N_HT_PROT_TYPE = 0x0085,
650 * 11n RIFS Protection Enable Flag
651 * -----------------------------------------------------------
652 * Configuration : Disable Enable
653 * Values to set : 0 1
654 * -----------------------------------------------------------
656 WID_11N_RIFS_PROT_ENABLE = 0x0086,
660 * -----------------------------------------------------------
661 * Configuration : Static Dynamic MIMO (Power Save Disabled)
662 * Values to set : 1 2 3
663 * -----------------------------------------------------------
665 WID_11N_SMPS_MODE = 0x0087,
668 * Current transmit MCS
669 * -----------------------------------------------------------
670 * Configuration : MCS Index for data rate
671 * Values to set : 0 to 7
672 * -----------------------------------------------------------
674 WID_11N_CURRENT_TX_MCS = 0x0088,
676 WID_11N_PRINT_STATS = 0x0089,
679 * 11n Short GI Enable Flag
680 * -----------------------------------------------------------
681 * Configuration : Disable Enable
682 * Values to set : 0 1
683 * -----------------------------------------------------------
685 WID_11N_SHORT_GI_ENABLE = 0x008D,
688 * 11n RIFS Enable Flag
689 * -----------------------------------------------------------
690 * Configuration : Disable Enable
691 * Values to set : 0 1
692 * -----------------------------------------------------------
694 WID_RIFS_MODE = 0x0094,
698 * -----------------------------------------------------------
699 * Configuration : Disable Self CTS Enable Self CTS
700 * Values to set : 0 1
701 * Configuration : Disable TX Abort Enable TX Abort
702 * Values to set : 2 3
703 * Configuration : Enable HW TX Abort Enable SW TX Abort
704 * Values to set : 4 5
705 * -----------------------------------------------------------
707 WID_TX_ABORT_CONFIG = 0x00A1,
709 WID_REG_TSSI_11B_VALUE = 0x00A6,
710 WID_REG_TSSI_11G_VALUE = 0x00A7,
711 WID_REG_TSSI_11N_VALUE = 0x00A8,
712 WID_TX_CALIBRATION = 0x00A9,
713 WID_DSCR_TSSI_11B_VALUE = 0x00AA,
714 WID_DSCR_TSSI_11G_VALUE = 0x00AB,
715 WID_DSCR_TSSI_11N_VALUE = 0x00AC,
718 * Immediate Block-Ack Support
719 * -----------------------------------------------------------
720 * Configuration : Disable Enable
721 * Values to set : 0 1
722 * -----------------------------------------------------------
724 WID_11N_IMMEDIATE_BA_ENABLED = 0x00AF,
728 * -----------------------------------------------------------
729 * Configuration : Disable Enable
730 * Values to set : 1 0
731 * -----------------------------------------------------------
733 WID_11N_TXOP_PROT_DISABLE = 0x00B0,
735 WID_TX_POWER_LEVEL_11N = 0x00B1,
737 /* Custom Character WID list */
738 WID_PC_TEST_MODE = 0x00C8,
739 /* SCAN Complete notification WID*/
740 WID_SCAN_COMPLETE = 0x00C9,
742 WID_DEL_BEACON = 0x00CA,
744 WID_LOGTerminal_Switch = 0x00CD,
745 WID_TX_POWER = 0x00CE,
746 /* EMAC Short WID list */
749 * -----------------------------------------------------------
750 * Configuration : Any value between 256 to 2347
751 * Values to set : Same value. Default is 2347
752 * -----------------------------------------------------------
754 WID_RTS_THRESHOLD = 0x1000,
757 * Fragmentation Threshold
758 * -----------------------------------------------------------
759 * Configuration : Any value between 256 to 2346
760 * Values to set : Same value. Default is 2346
761 * -----------------------------------------------------------
763 WID_FRAG_THRESHOLD = 0x1001,
765 WID_SHORT_RETRY_LIMIT = 0x1002,
766 WID_LONG_RETRY_LIMIT = 0x1003,
767 WID_BEACON_INTERVAL = 0x1006,
768 WID_MEMORY_ACCESS_16BIT = 0x1008,
769 WID_RX_SENSE = 0x100B,
770 WID_ACTIVE_SCAN_TIME = 0x100C,
771 WID_PASSIVE_SCAN_TIME = 0x100D,
773 WID_SITE_SURVEY_SCAN_TIME = 0x100E,
774 WID_JOIN_START_TIMEOUT = 0x100F,
775 WID_AUTH_TIMEOUT = 0x1010,
776 WID_ASOC_TIMEOUT = 0x1011,
777 WID_11I_PROTOCOL_TIMEOUT = 0x1012,
778 WID_EAPOL_RESPONSE_TIMEOUT = 0x1013,
780 /* NMAC Short WID list */
781 WID_11N_SIG_QUAL_VAL = 0x1085,
782 WID_CCA_THRESHOLD = 0x1087,
784 /* Custom Short WID list */
786 /* EMAC Integer WID list */
787 WID_FAILED_COUNT = 0x2000,
788 WID_RETRY_COUNT = 0x2001,
789 WID_MULTIPLE_RETRY_COUNT = 0x2002,
790 WID_FRAME_DUPLICATE_COUNT = 0x2003,
791 WID_ACK_FAILURE_COUNT = 0x2004,
792 WID_RECEIVED_FRAGMENT_COUNT = 0x2005,
793 WID_MCAST_RECEIVED_FRAME_COUNT = 0x2006,
794 WID_FCS_ERROR_COUNT = 0x2007,
795 WID_SUCCESS_FRAME_COUNT = 0x2008,
796 WID_HUT_TX_COUNT = 0x200A,
797 WID_TX_FRAGMENT_COUNT = 0x200B,
798 WID_TX_MULTICAST_FRAME_COUNT = 0x200C,
799 WID_RTS_SUCCESS_COUNT = 0x200D,
800 WID_RTS_FAILURE_COUNT = 0x200E,
801 WID_WEP_UNDECRYPTABLE_COUNT = 0x200F,
802 WID_REKEY_PERIOD = 0x2010,
803 WID_REKEY_PACKET_COUNT = 0x2011,
804 WID_1X_SERV_ADDR = 0x2012,
805 WID_STACK_IP_ADDR = 0x2013,
806 WID_STACK_NETMASK_ADDR = 0x2014,
807 WID_HW_RX_COUNT = 0x2015,
808 WID_MEMORY_ADDRESS = 0x201E,
809 WID_MEMORY_ACCESS_32BIT = 0x201F,
810 WID_RF_REG_VAL = 0x2021,
812 /* NMAC Integer WID list */
813 WID_11N_PHY_ACTIVE_REG_VAL = 0x2080,
815 /* Custom Integer WID list */
816 WID_GET_INACTIVE_TIME = 0x2084,
817 WID_SET_OPERATION_MODE = 0X2086,
818 /* EMAC String WID list */
820 WID_FIRMWARE_VERSION = 0x3001,
821 WID_OPERATIONAL_RATE_SET = 0x3002,
823 WID_WEP_KEY_VALUE = 0x3004,
824 WID_11I_PSK = 0x3008,
825 WID_11E_P_ACTION_REQ = 0x3009,
827 WID_HARDWARE_VERSION = 0x300B,
828 WID_MAC_ADDR = 0x300C,
829 WID_HUT_DEST_ADDR = 0x300D,
830 WID_PHY_VERSION = 0x300F,
831 WID_SUPP_USERNAME = 0x3010,
832 WID_SUPP_PASSWORD = 0x3011,
833 WID_SITE_SURVEY_RESULTS = 0x3012,
834 WID_RX_POWER_LEVEL = 0x3013,
835 WID_DEL_ALL_RX_BA = 0x3014,
836 WID_SET_STA_MAC_INACTIVE_TIME = 0x3017,
837 WID_ADD_WEP_KEY = 0x3019,
838 WID_REMOVE_WEP_KEY = 0x301A,
839 WID_ADD_PTK = 0x301B,
840 WID_ADD_RX_GTK = 0x301C,
841 WID_ADD_TX_GTK = 0x301D,
842 WID_REMOVE_KEY = 0x301E,
843 WID_ASSOC_REQ_INFO = 0x301F,
844 WID_ASSOC_RES_INFO = 0x3020,
845 WID_MANUFACTURER = 0x3026, /*Added for CAPI tool */
846 WID_MODEL_NAME = 0x3027, /*Added for CAPI tool */
847 WID_MODEL_NUM = 0x3028, /*Added for CAPI tool */
848 WID_DEVICE_NAME = 0x3029, /*Added for CAPI tool */
849 WID_SET_DRV_HANDLER = 0x3079,
851 /* NMAC String WID list */
852 WID_11N_P_ACTION_REQ = 0x3080,
853 WID_HUT_TEST_ID = 0x3081,
854 WID_PMKID_INFO = 0x3082,
855 WID_FIRMWARE_INFO = 0x3083,
856 WID_REGISTER_FRAME = 0x3084,
857 WID_DEL_ALL_STA = 0x3085,
858 WID_REMAIN_ON_CHAN = 0x3996,
859 WID_SSID_PROBE_REQ = 0x3997,
860 WID_JOIN_REQ_EXTENDED = 0x3998,
862 WID_IP_ADDRESS = 0x3999,
864 /* Custom String WID list */
866 /* EMAC Binary WID list */
867 WID_UAPSD_CONFIG = 0x4001,
868 WID_UAPSD_STATUS = 0x4002,
869 WID_WMM_AP_AC_PARAMS = 0x4003,
870 WID_WMM_STA_AC_PARAMS = 0x4004,
871 WID_NETWORK_INFO = 0x4005,
872 WID_STA_JOIN_INFO = 0x4006,
873 WID_CONNECTED_STA_LIST = 0x4007,
875 /* NMAC Binary WID list */
876 WID_11N_AUTORATE_TABLE = 0x4080,
878 WID_SCAN_CHANNEL_LIST = 0x4084,
880 WID_INFO_ELEMENT_PROBE = 0x4085,
881 WID_INFO_ELEMENT_ASSOCIATE = 0x4086,
882 WID_ADD_STA = 0X4087,
883 WID_REMOVE_STA = 0X4088,
884 WID_EDIT_STA = 0X4089,
885 WID_ADD_BEACON = 0x408a,
887 WID_SETUP_MULTICAST_FILTER = 0x408b,
889 /* Miscellaneous WIDs */
895 int wilc_wlan_init(struct net_device *dev);
896 u32 wilc_get_chipid(struct wilc *wilc, bool update);