drivers/spi/spi-s3c64xx.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 //
   3 // Copyright (c) 2009 Samsung Electronics Co., Ltd.
   4 //      Jaswinder Singh <jassi.brar@samsung.com>
   5
   6 #include <linux/init.h>
   7 #include <linux/module.h>
   8 #include <linux/interrupt.h>
   9 #include <linux/delay.h>
  10 #include <linux/clk.h>
  11 #include <linux/dma-mapping.h>
  12 #include <linux/dmaengine.h>
  13 #include <linux/platform_device.h>
  14 #include <linux/pm_runtime.h>
  15 #include <linux/spi/spi.h>
  16 #include <linux/gpio.h>
  17 #include <linux/of.h>
  18 #include <linux/of_gpio.h>
  19
  20 #include <linux/platform_data/spi-s3c64xx.h>
  21
  22 #define MAX_SPI_PORTS           6
  23 #define S3C64XX_SPI_QUIRK_POLL          (1 << 0)
  24 #define S3C64XX_SPI_QUIRK_CS_AUTO       (1 << 1)
  25 #define AUTOSUSPEND_TIMEOUT     2000
  26
  27 /* Registers and bit-fields */
  28
  29 #define S3C64XX_SPI_CH_CFG              0x00
  30 #define S3C64XX_SPI_CLK_CFG             0x04
  31 #define S3C64XX_SPI_MODE_CFG            0x08
  32 #define S3C64XX_SPI_SLAVE_SEL           0x0C
  33 #define S3C64XX_SPI_INT_EN              0x10
  34 #define S3C64XX_SPI_STATUS              0x14
  35 #define S3C64XX_SPI_TX_DATA             0x18
  36 #define S3C64XX_SPI_RX_DATA             0x1C
  37 #define S3C64XX_SPI_PACKET_CNT          0x20
  38 #define S3C64XX_SPI_PENDING_CLR         0x24
  39 #define S3C64XX_SPI_SWAP_CFG            0x28
  40 #define S3C64XX_SPI_FB_CLK              0x2C
  41
  42 #define S3C64XX_SPI_CH_HS_EN            (1<<6)  /* High Speed Enable */
  43 #define S3C64XX_SPI_CH_SW_RST           (1<<5)
  44 #define S3C64XX_SPI_CH_SLAVE            (1<<4)
  45 #define S3C64XX_SPI_CPOL_L              (1<<3)
  46 #define S3C64XX_SPI_CPHA_B              (1<<2)
  47 #define S3C64XX_SPI_CH_RXCH_ON          (1<<1)
  48 #define S3C64XX_SPI_CH_TXCH_ON          (1<<0)
  49
  50 #define S3C64XX_SPI_CLKSEL_SRCMSK       (3<<9)
  51 #define S3C64XX_SPI_CLKSEL_SRCSHFT      9
  52 #define S3C64XX_SPI_ENCLK_ENABLE        (1<<8)
  53 #define S3C64XX_SPI_PSR_MASK            0xff
  54
  55 #define S3C64XX_SPI_MODE_CH_TSZ_BYTE            (0<<29)
  56 #define S3C64XX_SPI_MODE_CH_TSZ_HALFWORD        (1<<29)
  57 #define S3C64XX_SPI_MODE_CH_TSZ_WORD            (2<<29)
  58 #define S3C64XX_SPI_MODE_CH_TSZ_MASK            (3<<29)
  59 #define S3C64XX_SPI_MODE_BUS_TSZ_BYTE           (0<<17)
  60 #define S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD       (1<<17)
  61 #define S3C64XX_SPI_MODE_BUS_TSZ_WORD           (2<<17)
  62 #define S3C64XX_SPI_MODE_BUS_TSZ_MASK           (3<<17)
  63 #define S3C64XX_SPI_MODE_RXDMA_ON               (1<<2)
  64 #define S3C64XX_SPI_MODE_TXDMA_ON               (1<<1)
  65 #define S3C64XX_SPI_MODE_4BURST                 (1<<0)
  66
  67 #define S3C64XX_SPI_SLAVE_AUTO                  (1<<1)
  68 #define S3C64XX_SPI_SLAVE_SIG_INACT             (1<<0)
  69 #define S3C64XX_SPI_SLAVE_NSC_CNT_2             (2<<4)
  70
  71 #define S3C64XX_SPI_INT_TRAILING_EN             (1<<6)
  72 #define S3C64XX_SPI_INT_RX_OVERRUN_EN           (1<<5)
  73 #define S3C64XX_SPI_INT_RX_UNDERRUN_EN          (1<<4)
  74 #define S3C64XX_SPI_INT_TX_OVERRUN_EN           (1<<3)
  75 #define S3C64XX_SPI_INT_TX_UNDERRUN_EN          (1<<2)
  76 #define S3C64XX_SPI_INT_RX_FIFORDY_EN           (1<<1)
  77 #define S3C64XX_SPI_INT_TX_FIFORDY_EN           (1<<0)
  78
  79 #define S3C64XX_SPI_ST_RX_OVERRUN_ERR           (1<<5)
  80 #define S3C64XX_SPI_ST_RX_UNDERRUN_ERR          (1<<4)
  81 #define S3C64XX_SPI_ST_TX_OVERRUN_ERR           (1<<3)
  82 #define S3C64XX_SPI_ST_TX_UNDERRUN_ERR          (1<<2)
  83 #define S3C64XX_SPI_ST_RX_FIFORDY               (1<<1)
  84 #define S3C64XX_SPI_ST_TX_FIFORDY               (1<<0)
  85
  86 #define S3C64XX_SPI_PACKET_CNT_EN               (1<<16)
  87
  88 #define S3C64XX_SPI_PND_TX_UNDERRUN_CLR         (1<<4)
  89 #define S3C64XX_SPI_PND_TX_OVERRUN_CLR          (1<<3)
  90 #define S3C64XX_SPI_PND_RX_UNDERRUN_CLR         (1<<2)
  91 #define S3C64XX_SPI_PND_RX_OVERRUN_CLR          (1<<1)
  92 #define S3C64XX_SPI_PND_TRAILING_CLR            (1<<0)
  93
  94 #define S3C64XX_SPI_SWAP_RX_HALF_WORD           (1<<7)
  95 #define S3C64XX_SPI_SWAP_RX_BYTE                (1<<6)
  96 #define S3C64XX_SPI_SWAP_RX_BIT                 (1<<5)
  97 #define S3C64XX_SPI_SWAP_RX_EN                  (1<<4)
  98 #define S3C64XX_SPI_SWAP_TX_HALF_WORD           (1<<3)
  99 #define S3C64XX_SPI_SWAP_TX_BYTE                (1<<2)
 100 #define S3C64XX_SPI_SWAP_TX_BIT                 (1<<1)
 101 #define S3C64XX_SPI_SWAP_TX_EN                  (1<<0)
 102
 103 #define S3C64XX_SPI_FBCLK_MSK                   (3<<0)
 104
 105 #define FIFO_LVL_MASK(i) ((i)->port_conf->fifo_lvl_mask[i->port_id])
 106 #define S3C64XX_SPI_ST_TX_DONE(v, i) (((v) & \
 107                                 (1 << (i)->port_conf->tx_st_done)) ? 1 : 0)
 108 #define TX_FIFO_LVL(v, i) (((v) >> 6) & FIFO_LVL_MASK(i))
 109 #define RX_FIFO_LVL(v, i) (((v) >> (i)->port_conf->rx_lvl_offset) & \
 110                                         FIFO_LVL_MASK(i))
 111
 112 #define S3C64XX_SPI_MAX_TRAILCNT        0x3ff
 113 #define S3C64XX_SPI_TRAILCNT_OFF        19
 114
 115 #define S3C64XX_SPI_TRAILCNT            S3C64XX_SPI_MAX_TRAILCNT
 116
 117 #define msecs_to_loops(t) (loops_per_jiffy / 1000 * HZ * t)
 118 #define is_polling(x)   (x->port_conf->quirks & S3C64XX_SPI_QUIRK_POLL)
 119
 120 #define RXBUSY    (1<<2)
 121 #define TXBUSY    (1<<3)
 122
 123 struct s3c64xx_spi_dma_data {
 124         struct dma_chan *ch;
 125         enum dma_transfer_direction direction;
 126 };
 127
 128 /**
 129  * struct s3c64xx_spi_info - SPI Controller hardware info
 130  * @fifo_lvl_mask: Bit-mask for {TX|RX}_FIFO_LVL bits in SPI_STATUS register.
 131  * @rx_lvl_offset: Bit offset of RX_FIFO_LVL bits in SPI_STATUS regiter.
 132  * @tx_st_done: Bit offset of TX_DONE bit in SPI_STATUS regiter.
 133  * @quirks: Bitmask of known quirks
 134  * @high_speed: True, if the controller supports HIGH_SPEED_EN bit.
 135  * @clk_from_cmu: True, if the controller does not include a clock mux and
 136  *      prescaler unit.
 137  * @clk_ioclk: True if clock is present on this device
 138  *
 139  * The Samsung s3c64xx SPI controller are used on various Samsung SoC's but
 140  * differ in some aspects such as the size of the fifo and spi bus clock
 141  * setup. Such differences are specified to the driver using this structure
 142  * which is provided as driver data to the driver.
 143  */
 144 struct s3c64xx_spi_port_config {
 145         int     fifo_lvl_mask[MAX_SPI_PORTS];
 146         int     rx_lvl_offset;
 147         int     tx_st_done;
 148         int     quirks;
 149         bool    high_speed;
 150         bool    clk_from_cmu;
 151         bool    clk_ioclk;
 152 };
 153
 154 /**
 155  * struct s3c64xx_spi_driver_data - Runtime info holder for SPI driver.
 156  * @clk: Pointer to the spi clock.
 157  * @src_clk: Pointer to the clock used to generate SPI signals.
 158  * @ioclk: Pointer to the i/o clock between master and slave
 159  * @pdev: Pointer to device's platform device data
 160  * @master: Pointer to the SPI Protocol master.
 161  * @cntrlr_info: Platform specific data for the controller this driver manages.
 162  * @lock: Controller specific lock.
 163  * @state: Set of FLAGS to indicate status.
 164  * @rx_dmach: Controller's DMA channel for Rx.
 165  * @tx_dmach: Controller's DMA channel for Tx.
 166  * @sfr_start: BUS address of SPI controller regs.
 167  * @regs: Pointer to ioremap'ed controller registers.
 168  * @irq: interrupt
 169  * @xfer_completion: To indicate completion of xfer task.
 170  * @cur_mode: Stores the active configuration of the controller.
 171  * @cur_bpw: Stores the active bits per word settings.
 172  * @cur_speed: Current clock speed
 173  * @rx_dma: Local receive DMA data (e.g. chan and direction)
 174  * @tx_dma: Local transmit DMA data (e.g. chan and direction)
 175  * @port_conf: Local SPI port configuartion data
 176  * @port_id: Port identification number
 177  */
 178 struct s3c64xx_spi_driver_data {
 179         void __iomem                    *regs;
 180         struct clk                      *clk;
 181         struct clk                      *src_clk;
 182         struct clk                      *ioclk;
 183         struct platform_device          *pdev;
 184         struct spi_master               *master;
 185         struct s3c64xx_spi_info  *cntrlr_info;
 186         spinlock_t                      lock;
 187         unsigned long                   sfr_start;
 188         struct completion               xfer_completion;
 189         unsigned                        state;
 190         unsigned                        cur_mode, cur_bpw;
 191         unsigned                        cur_speed;
 192         struct s3c64xx_spi_dma_data     rx_dma;
 193         struct s3c64xx_spi_dma_data     tx_dma;
 194         struct s3c64xx_spi_port_config  *port_conf;
 195         unsigned int                    port_id;
 196 };
 197
 198 static void s3c64xx_flush_fifo(struct s3c64xx_spi_driver_data *sdd)
 199 {
 200         void __iomem *regs = sdd->regs;
 201         unsigned long loops;
 202         u32 val;
 203
 204         writel(0, regs + S3C64XX_SPI_PACKET_CNT);
 205
 206         val = readl(regs + S3C64XX_SPI_CH_CFG);
 207         val &= ~(S3C64XX_SPI_CH_RXCH_ON | S3C64XX_SPI_CH_TXCH_ON);
 208         writel(val, regs + S3C64XX_SPI_CH_CFG);
 209
 210         val = readl(regs + S3C64XX_SPI_CH_CFG);
 211         val |= S3C64XX_SPI_CH_SW_RST;
 212         val &= ~S3C64XX_SPI_CH_HS_EN;
 213         writel(val, regs + S3C64XX_SPI_CH_CFG);
 214
 215         /* Flush TxFIFO*/
 216         loops = msecs_to_loops(1);
 217         do {
 218                 val = readl(regs + S3C64XX_SPI_STATUS);
 219         } while (TX_FIFO_LVL(val, sdd) && loops--);
 220
 221         if (loops == 0)
 222                 dev_warn(&sdd->pdev->dev, "Timed out flushing TX FIFO\n");
 223
 224         /* Flush RxFIFO*/
 225         loops = msecs_to_loops(1);
 226         do {
 227                 val = readl(regs + S3C64XX_SPI_STATUS);
 228                 if (RX_FIFO_LVL(val, sdd))
 229                         readl(regs + S3C64XX_SPI_RX_DATA);
 230                 else
 231                         break;
 232         } while (loops--);
 233
 234         if (loops == 0)
 235                 dev_warn(&sdd->pdev->dev, "Timed out flushing RX FIFO\n");
 236
 237         val = readl(regs + S3C64XX_SPI_CH_CFG);
 238         val &= ~S3C64XX_SPI_CH_SW_RST;
 239         writel(val, regs + S3C64XX_SPI_CH_CFG);
 240
 241         val = readl(regs + S3C64XX_SPI_MODE_CFG);
 242         val &= ~(S3C64XX_SPI_MODE_TXDMA_ON | S3C64XX_SPI_MODE_RXDMA_ON);
 243         writel(val, regs + S3C64XX_SPI_MODE_CFG);
 244 }
 245
 246 static void s3c64xx_spi_dmacb(void *data)
 247 {
 248         struct s3c64xx_spi_driver_data *sdd;
 249         struct s3c64xx_spi_dma_data *dma = data;
 250         unsigned long flags;
 251
 252         if (dma->direction == DMA_DEV_TO_MEM)
 253                 sdd = container_of(data,
 254                         struct s3c64xx_spi_driver_data, rx_dma);
 255         else
 256                 sdd = container_of(data,
 257                         struct s3c64xx_spi_driver_data, tx_dma);
 258
 259         spin_lock_irqsave(&sdd->lock, flags);
 260
 261         if (dma->direction == DMA_DEV_TO_MEM) {
 262                 sdd->state &= ~RXBUSY;
 263                 if (!(sdd->state & TXBUSY))
 264                         complete(&sdd->xfer_completion);
 265         } else {
 266                 sdd->state &= ~TXBUSY;
 267                 if (!(sdd->state & RXBUSY))
 268                         complete(&sdd->xfer_completion);
 269         }
 270
 271         spin_unlock_irqrestore(&sdd->lock, flags);
 272 }
 273
 274 static void prepare_dma(struct s3c64xx_spi_dma_data *dma,
 275                         struct sg_table *sgt)
 276 {
 277         struct s3c64xx_spi_driver_data *sdd;
 278         struct dma_slave_config config;
 279         struct dma_async_tx_descriptor *desc;
 280
 281         memset(&config, 0, sizeof(config));
 282
 283         if (dma->direction == DMA_DEV_TO_MEM) {
 284                 sdd = container_of((void *)dma,
 285                         struct s3c64xx_spi_driver_data, rx_dma);
 286                 config.direction = dma->direction;
 287                 config.src_addr = sdd->sfr_start + S3C64XX_SPI_RX_DATA;
 288                 config.src_addr_width = sdd->cur_bpw / 8;
 289                 config.src_maxburst = 1;
 290                 dmaengine_slave_config(dma->ch, &config);
 291         } else {
 292                 sdd = container_of((void *)dma,
 293                         struct s3c64xx_spi_driver_data, tx_dma);
 294                 config.direction = dma->direction;
 295                 config.dst_addr = sdd->sfr_start + S3C64XX_SPI_TX_DATA;
 296                 config.dst_addr_width = sdd->cur_bpw / 8;
 297                 config.dst_maxburst = 1;
 298                 dmaengine_slave_config(dma->ch, &config);
 299         }
 300
 301         desc = dmaengine_prep_slave_sg(dma->ch, sgt->sgl, sgt->nents,
 302                                        dma->direction, DMA_PREP_INTERRUPT);
 303
 304         desc->callback = s3c64xx_spi_dmacb;
 305         desc->callback_param = dma;
 306
 307         dmaengine_submit(desc);
 308         dma_async_issue_pending(dma->ch);
 309 }
 310
 311 static void s3c64xx_spi_set_cs(struct spi_device *spi, bool enable)
 312 {
 313         struct s3c64xx_spi_driver_data *sdd =
 314                                         spi_master_get_devdata(spi->master);
 315
 316         if (sdd->cntrlr_info->no_cs)
 317                 return;
 318
 319         if (enable) {
 320                 if (!(sdd->port_conf->quirks & S3C64XX_SPI_QUIRK_CS_AUTO)) {
 321                         writel(0, sdd->regs + S3C64XX_SPI_SLAVE_SEL);
 322                 } else {
 323                         u32 ssel = readl(sdd->regs + S3C64XX_SPI_SLAVE_SEL);
 324
 325                         ssel |= (S3C64XX_SPI_SLAVE_AUTO |
 326                                                 S3C64XX_SPI_SLAVE_NSC_CNT_2);
 327                         writel(ssel, sdd->regs + S3C64XX_SPI_SLAVE_SEL);
 328                 }
 329         } else {
 330                 if (!(sdd->port_conf->quirks & S3C64XX_SPI_QUIRK_CS_AUTO))
 331                         writel(S3C64XX_SPI_SLAVE_SIG_INACT,
 332                                sdd->regs + S3C64XX_SPI_SLAVE_SEL);
 333         }
 334 }
 335
 336 static int s3c64xx_spi_prepare_transfer(struct spi_master *spi)
 337 {
 338         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(spi);
 339
 340         if (is_polling(sdd))
 341                 return 0;
 342
 343         spi->dma_rx = sdd->rx_dma.ch;
 344         spi->dma_tx = sdd->tx_dma.ch;
 345
 346         return 0;
 347 }
 348
 349 static bool s3c64xx_spi_can_dma(struct spi_master *master,
 350                                 struct spi_device *spi,
 351                                 struct spi_transfer *xfer)
 352 {
 353         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
 354
 355         return xfer->len > (FIFO_LVL_MASK(sdd) >> 1) + 1;
 356 }
 357
 358 static void s3c64xx_enable_datapath(struct s3c64xx_spi_driver_data *sdd,
 359                                     struct spi_transfer *xfer, int dma_mode)
 360 {
 361         void __iomem *regs = sdd->regs;
 362         u32 modecfg, chcfg;
 363
 364         modecfg = readl(regs + S3C64XX_SPI_MODE_CFG);
 365         modecfg &= ~(S3C64XX_SPI_MODE_TXDMA_ON | S3C64XX_SPI_MODE_RXDMA_ON);
 366
 367         chcfg = readl(regs + S3C64XX_SPI_CH_CFG);
 368         chcfg &= ~S3C64XX_SPI_CH_TXCH_ON;
 369
 370         if (dma_mode) {
 371                 chcfg &= ~S3C64XX_SPI_CH_RXCH_ON;
 372         } else {
 373                 /* Always shift in data in FIFO, even if xfer is Tx only,
 374                  * this helps setting PCKT_CNT value for generating clocks
 375                  * as exactly needed.
 376                  */
 377                 chcfg |= S3C64XX_SPI_CH_RXCH_ON;
 378                 writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff)
 379                                         | S3C64XX_SPI_PACKET_CNT_EN,
 380                                         regs + S3C64XX_SPI_PACKET_CNT);
 381         }
 382
 383         if (xfer->tx_buf != NULL) {
 384                 sdd->state |= TXBUSY;
 385                 chcfg |= S3C64XX_SPI_CH_TXCH_ON;
 386                 if (dma_mode) {
 387                         modecfg |= S3C64XX_SPI_MODE_TXDMA_ON;
 388                         prepare_dma(&sdd->tx_dma, &xfer->tx_sg);
 389                 } else {
 390                         switch (sdd->cur_bpw) {
 391                         case 32:
 392                                 iowrite32_rep(regs + S3C64XX_SPI_TX_DATA,
 393                                         xfer->tx_buf, xfer->len / 4);
 394                                 break;
 395                         case 16:
 396                                 iowrite16_rep(regs + S3C64XX_SPI_TX_DATA,
 397                                         xfer->tx_buf, xfer->len / 2);
 398                                 break;
 399                         default:
 400                                 iowrite8_rep(regs + S3C64XX_SPI_TX_DATA,
 401                                         xfer->tx_buf, xfer->len);
 402                                 break;
 403                         }
 404                 }
 405         }
 406
 407         if (xfer->rx_buf != NULL) {
 408                 sdd->state |= RXBUSY;
 409
 410                 if (sdd->port_conf->high_speed && sdd->cur_speed >= 30000000UL
 411                                         && !(sdd->cur_mode & SPI_CPHA))
 412                         chcfg |= S3C64XX_SPI_CH_HS_EN;
 413
 414                 if (dma_mode) {
 415                         modecfg |= S3C64XX_SPI_MODE_RXDMA_ON;
 416                         chcfg |= S3C64XX_SPI_CH_RXCH_ON;
 417                         writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff)
 418                                         | S3C64XX_SPI_PACKET_CNT_EN,
 419                                         regs + S3C64XX_SPI_PACKET_CNT);
 420                         prepare_dma(&sdd->rx_dma, &xfer->rx_sg);
 421                 }
 422         }
 423
 424         writel(modecfg, regs + S3C64XX_SPI_MODE_CFG);
 425         writel(chcfg, regs + S3C64XX_SPI_CH_CFG);
 426 }
 427
 428 static u32 s3c64xx_spi_wait_for_timeout(struct s3c64xx_spi_driver_data *sdd,
 429                                         int timeout_ms)
 430 {
 431         void __iomem *regs = sdd->regs;
 432         unsigned long val = 1;
 433         u32 status;
 434
 435         /* max fifo depth available */
 436         u32 max_fifo = (FIFO_LVL_MASK(sdd) >> 1) + 1;
 437
 438         if (timeout_ms)
 439                 val = msecs_to_loops(timeout_ms);
 440
 441         do {
 442                 status = readl(regs + S3C64XX_SPI_STATUS);
 443         } while (RX_FIFO_LVL(status, sdd) < max_fifo && --val);
 444
 445         /* return the actual received data length */
 446         return RX_FIFO_LVL(status, sdd);
 447 }
 448
 449 static int s3c64xx_wait_for_dma(struct s3c64xx_spi_driver_data *sdd,
 450                                 struct spi_transfer *xfer)
 451 {
 452         void __iomem *regs = sdd->regs;
 453         unsigned long val;
 454         u32 status;
 455         int ms;
 456
 457         /* millisecs to xfer 'len' bytes @ 'cur_speed' */
 458         ms = xfer->len * 8 * 1000 / sdd->cur_speed;
 459         ms += 10; /* some tolerance */
 460
 461         val = msecs_to_jiffies(ms) + 10;
 462         val = wait_for_completion_timeout(&sdd->xfer_completion, val);
 463
 464         /*
 465          * If the previous xfer was completed within timeout, then
 466          * proceed further else return -EIO.
 467          * DmaTx returns after simply writing data in the FIFO,
 468          * w/o waiting for real transmission on the bus to finish.
 469          * DmaRx returns only after Dma read data from FIFO which
 470          * needs bus transmission to finish, so we don't worry if
 471          * Xfer involved Rx(with or without Tx).
 472          */
 473         if (val && !xfer->rx_buf) {
 474                 val = msecs_to_loops(10);
 475                 status = readl(regs + S3C64XX_SPI_STATUS);
 476                 while ((TX_FIFO_LVL(status, sdd)
 477                         || !S3C64XX_SPI_ST_TX_DONE(status, sdd))
 478                        && --val) {
 479                         cpu_relax();
 480                         status = readl(regs + S3C64XX_SPI_STATUS);
 481                 }
 482
 483         }
 484
 485         /* If timed out while checking rx/tx status return error */
 486         if (!val)
 487                 return -EIO;
 488
 489         return 0;
 490 }
 491
 492 static int s3c64xx_wait_for_pio(struct s3c64xx_spi_driver_data *sdd,
 493                                 struct spi_transfer *xfer)
 494 {
 495         void __iomem *regs = sdd->regs;
 496         unsigned long val;
 497         u32 status;
 498         int loops;
 499         u32 cpy_len;
 500         u8 *buf;
 501         int ms;
 502
 503         /* millisecs to xfer 'len' bytes @ 'cur_speed' */
 504         ms = xfer->len * 8 * 1000 / sdd->cur_speed;
 505         ms += 10; /* some tolerance */
 506
 507         val = msecs_to_loops(ms);
 508         do {
 509                 status = readl(regs + S3C64XX_SPI_STATUS);
 510         } while (RX_FIFO_LVL(status, sdd) < xfer->len && --val);
 511
 512         if (!val)
 513                 return -EIO;
 514
 515         /* If it was only Tx */
 516         if (!xfer->rx_buf) {
 517                 sdd->state &= ~TXBUSY;
 518                 return 0;
 519         }
 520
 521         /*
 522          * If the receive length is bigger than the controller fifo
 523          * size, calculate the loops and read the fifo as many times.
 524          * loops = length / max fifo size (calculated by using the
 525          * fifo mask).
 526          * For any size less than the fifo size the below code is
 527          * executed atleast once.
 528          */
 529         loops = xfer->len / ((FIFO_LVL_MASK(sdd) >> 1) + 1);
 530         buf = xfer->rx_buf;
 531         do {
 532                 /* wait for data to be received in the fifo */
 533                 cpy_len = s3c64xx_spi_wait_for_timeout(sdd,
 534                                                        (loops ? ms : 0));
 535
 536                 switch (sdd->cur_bpw) {
 537                 case 32:
 538                         ioread32_rep(regs + S3C64XX_SPI_RX_DATA,
 539                                      buf, cpy_len / 4);
 540                         break;
 541                 case 16:
 542                         ioread16_rep(regs + S3C64XX_SPI_RX_DATA,
 543                                      buf, cpy_len / 2);
 544                         break;
 545                 default:
 546                         ioread8_rep(regs + S3C64XX_SPI_RX_DATA,
 547                                     buf, cpy_len);
 548                         break;
 549                 }
 550
 551                 buf = buf + cpy_len;
 552         } while (loops--);
 553         sdd->state &= ~RXBUSY;
 554
 555         return 0;
 556 }
 557
 558 static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd)
 559 {
 560         void __iomem *regs = sdd->regs;
 561         u32 val;
 562
 563         /* Disable Clock */
 564         if (!sdd->port_conf->clk_from_cmu) {
 565                 val = readl(regs + S3C64XX_SPI_CLK_CFG);
 566                 val &= ~S3C64XX_SPI_ENCLK_ENABLE;
 567                 writel(val, regs + S3C64XX_SPI_CLK_CFG);
 568         }
 569
 570         /* Set Polarity and Phase */
 571         val = readl(regs + S3C64XX_SPI_CH_CFG);
 572         val &= ~(S3C64XX_SPI_CH_SLAVE |
 573                         S3C64XX_SPI_CPOL_L |
 574                         S3C64XX_SPI_CPHA_B);
 575
 576         if (sdd->cur_mode & SPI_CPOL)
 577                 val |= S3C64XX_SPI_CPOL_L;
 578
 579         if (sdd->cur_mode & SPI_CPHA)
 580                 val |= S3C64XX_SPI_CPHA_B;
 581
 582         writel(val, regs + S3C64XX_SPI_CH_CFG);
 583
 584         /* Set Channel & DMA Mode */
 585         val = readl(regs + S3C64XX_SPI_MODE_CFG);
 586         val &= ~(S3C64XX_SPI_MODE_BUS_TSZ_MASK
 587                         | S3C64XX_SPI_MODE_CH_TSZ_MASK);
 588
 589         switch (sdd->cur_bpw) {
 590         case 32:
 591                 val |= S3C64XX_SPI_MODE_BUS_TSZ_WORD;
 592                 val |= S3C64XX_SPI_MODE_CH_TSZ_WORD;
 593                 break;
 594         case 16:
 595                 val |= S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD;
 596                 val |= S3C64XX_SPI_MODE_CH_TSZ_HALFWORD;
 597                 break;
 598         default:
 599                 val |= S3C64XX_SPI_MODE_BUS_TSZ_BYTE;
 600                 val |= S3C64XX_SPI_MODE_CH_TSZ_BYTE;
 601                 break;
 602         }
 603
 604         writel(val, regs + S3C64XX_SPI_MODE_CFG);
 605
 606         if (sdd->port_conf->clk_from_cmu) {
 607                 /* The src_clk clock is divided internally by 2 */
 608                 clk_set_rate(sdd->src_clk, sdd->cur_speed * 2);
 609         } else {
 610                 /* Configure Clock */
 611                 val = readl(regs + S3C64XX_SPI_CLK_CFG);
 612                 val &= ~S3C64XX_SPI_PSR_MASK;
 613                 val |= ((clk_get_rate(sdd->src_clk) / sdd->cur_speed / 2 - 1)
 614                                 & S3C64XX_SPI_PSR_MASK);
 615                 writel(val, regs + S3C64XX_SPI_CLK_CFG);
 616
 617                 /* Enable Clock */
 618                 val = readl(regs + S3C64XX_SPI_CLK_CFG);
 619                 val |= S3C64XX_SPI_ENCLK_ENABLE;
 620                 writel(val, regs + S3C64XX_SPI_CLK_CFG);
 621         }
 622 }
 623
 624 #define XFER_DMAADDR_INVALID DMA_BIT_MASK(32)
 625
 626 static int s3c64xx_spi_prepare_message(struct spi_master *master,
 627                                        struct spi_message *msg)
 628 {
 629         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
 630         struct spi_device *spi = msg->spi;
 631         struct s3c64xx_spi_csinfo *cs = spi->controller_data;
 632
 633         /* Configure feedback delay */
 634         writel(cs->fb_delay & 0x3, sdd->regs + S3C64XX_SPI_FB_CLK);
 635
 636         return 0;
 637 }
 638
 639 static int s3c64xx_spi_transfer_one(struct spi_master *master,
 640                                     struct spi_device *spi,
 641                                     struct spi_transfer *xfer)
 642 {
 643         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
 644         const unsigned int fifo_len = (FIFO_LVL_MASK(sdd) >> 1) + 1;
 645         const void *tx_buf = NULL;
 646         void *rx_buf = NULL;
 647         int target_len = 0, origin_len = 0;
 648         int use_dma = 0;
 649         int status;
 650         u32 speed;
 651         u8 bpw;
 652         unsigned long flags;
 653
 654         reinit_completion(&sdd->xfer_completion);
 655
 656         /* Only BPW and Speed may change across transfers */
 657         bpw = xfer->bits_per_word;
 658         speed = xfer->speed_hz;
 659
 660         if (bpw != sdd->cur_bpw || speed != sdd->cur_speed) {
 661                 sdd->cur_bpw = bpw;
 662                 sdd->cur_speed = speed;
 663                 sdd->cur_mode = spi->mode;
 664                 s3c64xx_spi_config(sdd);
 665         }
 666
 667         if (!is_polling(sdd) && (xfer->len > fifo_len) &&
 668             sdd->rx_dma.ch && sdd->tx_dma.ch) {
 669                 use_dma = 1;
 670
 671         } else if (is_polling(sdd) && xfer->len > fifo_len) {
 672                 tx_buf = xfer->tx_buf;
 673                 rx_buf = xfer->rx_buf;
 674                 origin_len = xfer->len;
 675
 676                 target_len = xfer->len;
 677                 if (xfer->len > fifo_len)
 678                         xfer->len = fifo_len;
 679         }
 680
 681         do {
 682                 spin_lock_irqsave(&sdd->lock, flags);
 683
 684                 /* Pending only which is to be done */
 685                 sdd->state &= ~RXBUSY;
 686                 sdd->state &= ~TXBUSY;
 687
 688                 s3c64xx_enable_datapath(sdd, xfer, use_dma);
 689
 690                 /* Start the signals */
 691                 s3c64xx_spi_set_cs(spi, true);
 692
 693                 spin_unlock_irqrestore(&sdd->lock, flags);
 694
 695                 if (use_dma)
 696                         status = s3c64xx_wait_for_dma(sdd, xfer);
 697                 else
 698                         status = s3c64xx_wait_for_pio(sdd, xfer);
 699
 700                 if (status) {
 701                         dev_err(&spi->dev,
 702                                 "I/O Error: rx-%d tx-%d res:rx-%c tx-%c len-%d\n",
 703                                 xfer->rx_buf ? 1 : 0, xfer->tx_buf ? 1 : 0,
 704                                 (sdd->state & RXBUSY) ? 'f' : 'p',
 705                                 (sdd->state & TXBUSY) ? 'f' : 'p',
 706                                 xfer->len);
 707
 708                         if (use_dma) {
 709                                 if (xfer->tx_buf && (sdd->state & TXBUSY))
 710                                         dmaengine_terminate_all(sdd->tx_dma.ch);
 711                                 if (xfer->rx_buf && (sdd->state & RXBUSY))
 712                                         dmaengine_terminate_all(sdd->rx_dma.ch);
 713                         }
 714                 } else {
 715                         s3c64xx_flush_fifo(sdd);
 716                 }
 717                 if (target_len > 0) {
 718                         target_len -= xfer->len;
 719
 720                         if (xfer->tx_buf)
 721                                 xfer->tx_buf += xfer->len;
 722
 723                         if (xfer->rx_buf)
 724                                 xfer->rx_buf += xfer->len;
 725
 726                         if (target_len > fifo_len)
 727                                 xfer->len = fifo_len;
 728                         else
 729                                 xfer->len = target_len;
 730                 }
 731         } while (target_len > 0);
 732
 733         if (origin_len) {
 734                 /* Restore original xfer buffers and length */
 735                 xfer->tx_buf = tx_buf;
 736                 xfer->rx_buf = rx_buf;
 737                 xfer->len = origin_len;
 738         }
 739
 740         return status;
 741 }
 742
 743 static struct s3c64xx_spi_csinfo *s3c64xx_get_slave_ctrldata(
 744                                 struct spi_device *spi)
 745 {
 746         struct s3c64xx_spi_csinfo *cs;
 747         struct device_node *slave_np, *data_np = NULL;
 748         u32 fb_delay = 0;
 749
 750         slave_np = spi->dev.of_node;
 751         if (!slave_np) {
 752                 dev_err(&spi->dev, "device node not found\n");
 753                 return ERR_PTR(-EINVAL);
 754         }
 755
 756         data_np = of_get_child_by_name(slave_np, "controller-data");
 757         if (!data_np) {
 758                 dev_err(&spi->dev, "child node 'controller-data' not found\n");
 759                 return ERR_PTR(-EINVAL);
 760         }
 761
 762         cs = kzalloc(sizeof(*cs), GFP_KERNEL);
 763         if (!cs) {
 764                 of_node_put(data_np);
 765                 return ERR_PTR(-ENOMEM);
 766         }
 767
 768         of_property_read_u32(data_np, "samsung,spi-feedback-delay", &fb_delay);
 769         cs->fb_delay = fb_delay;
 770         of_node_put(data_np);
 771         return cs;
 772 }
 773
 774 /*
 775  * Here we only check the validity of requested configuration
 776  * and save the configuration in a local data-structure.
 777  * The controller is actually configured only just before we
 778  * get a message to transfer.
 779  */
 780 static int s3c64xx_spi_setup(struct spi_device *spi)
 781 {
 782         struct s3c64xx_spi_csinfo *cs = spi->controller_data;
 783         struct s3c64xx_spi_driver_data *sdd;
 784         int err;
 785
 786         sdd = spi_master_get_devdata(spi->master);
 787         if (spi->dev.of_node) {
 788                 cs = s3c64xx_get_slave_ctrldata(spi);
 789                 spi->controller_data = cs;
 790         } else if (cs) {
 791                 /* On non-DT platforms the SPI core will set spi->cs_gpio
 792                  * to -ENOENT. The GPIO pin used to drive the chip select
 793                  * is defined by using platform data so spi->cs_gpio value
 794                  * has to be override to have the proper GPIO pin number.
 795                  */
 796                 spi->cs_gpio = cs->line;
 797         }
 798
 799         if (IS_ERR_OR_NULL(cs)) {
 800                 dev_err(&spi->dev, "No CS for SPI(%d)\n", spi->chip_select);
 801                 return -ENODEV;
 802         }
 803
 804         if (!spi_get_ctldata(spi)) {
 805                 if (gpio_is_valid(spi->cs_gpio)) {
 806                         err = gpio_request_one(spi->cs_gpio, GPIOF_OUT_INIT_HIGH,
 807                                                dev_name(&spi->dev));
 808                         if (err) {
 809                                 dev_err(&spi->dev,
 810                                         "Failed to get /CS gpio [%d]: %d\n",
 811                                         spi->cs_gpio, err);
 812                                 goto err_gpio_req;
 813                         }
 814                 }
 815
 816                 spi_set_ctldata(spi, cs);
 817         }
 818
 819         pm_runtime_get_sync(&sdd->pdev->dev);
 820
 821         /* Check if we can provide the requested rate */
 822         if (!sdd->port_conf->clk_from_cmu) {
 823                 u32 psr, speed;
 824
 825                 /* Max possible */
 826                 speed = clk_get_rate(sdd->src_clk) / 2 / (0 + 1);
 827
 828                 if (spi->max_speed_hz > speed)
 829                         spi->max_speed_hz = speed;
 830
 831                 psr = clk_get_rate(sdd->src_clk) / 2 / spi->max_speed_hz - 1;
 832                 psr &= S3C64XX_SPI_PSR_MASK;
 833                 if (psr == S3C64XX_SPI_PSR_MASK)
 834                         psr--;
 835
 836                 speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1);
 837                 if (spi->max_speed_hz < speed) {
 838                         if (psr+1 < S3C64XX_SPI_PSR_MASK) {
 839                                 psr++;
 840                         } else {
 841                                 err = -EINVAL;
 842                                 goto setup_exit;
 843                         }
 844                 }
 845
 846                 speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1);
 847                 if (spi->max_speed_hz >= speed) {
 848                         spi->max_speed_hz = speed;
 849                 } else {
 850                         dev_err(&spi->dev, "Can't set %dHz transfer speed\n",
 851                                 spi->max_speed_hz);
 852                         err = -EINVAL;
 853                         goto setup_exit;
 854                 }
 855         }
 856
 857         pm_runtime_mark_last_busy(&sdd->pdev->dev);
 858         pm_runtime_put_autosuspend(&sdd->pdev->dev);
 859         s3c64xx_spi_set_cs(spi, false);
 860
 861         return 0;
 862
 863 setup_exit:
 864         pm_runtime_mark_last_busy(&sdd->pdev->dev);
 865         pm_runtime_put_autosuspend(&sdd->pdev->dev);
 866         /* setup() returns with device de-selected */
 867         s3c64xx_spi_set_cs(spi, false);
 868
 869         if (gpio_is_valid(spi->cs_gpio))
 870                 gpio_free(spi->cs_gpio);
 871         spi_set_ctldata(spi, NULL);
 872
 873 err_gpio_req:
 874         if (spi->dev.of_node)
 875                 kfree(cs);
 876
 877         return err;
 878 }
 879
 880 static void s3c64xx_spi_cleanup(struct spi_device *spi)
 881 {
 882         struct s3c64xx_spi_csinfo *cs = spi_get_ctldata(spi);
 883
 884         if (gpio_is_valid(spi->cs_gpio)) {
 885                 gpio_free(spi->cs_gpio);
 886                 if (spi->dev.of_node)
 887                         kfree(cs);
 888                 else {
 889                         /* On non-DT platforms, the SPI core sets
 890                          * spi->cs_gpio to -ENOENT and .setup()
 891                          * overrides it with the GPIO pin value
 892                          * passed using platform data.
 893                          */
 894                         spi->cs_gpio = -ENOENT;
 895                 }
 896         }
 897
 898         spi_set_ctldata(spi, NULL);
 899 }
 900
 901 static irqreturn_t s3c64xx_spi_irq(int irq, void *data)
 902 {
 903         struct s3c64xx_spi_driver_data *sdd = data;
 904         struct spi_master *spi = sdd->master;
 905         unsigned int val, clr = 0;
 906
 907         val = readl(sdd->regs + S3C64XX_SPI_STATUS);
 908
 909         if (val & S3C64XX_SPI_ST_RX_OVERRUN_ERR) {
 910                 clr = S3C64XX_SPI_PND_RX_OVERRUN_CLR;
 911                 dev_err(&spi->dev, "RX overrun\n");
 912         }
 913         if (val & S3C64XX_SPI_ST_RX_UNDERRUN_ERR) {
 914                 clr |= S3C64XX_SPI_PND_RX_UNDERRUN_CLR;
 915                 dev_err(&spi->dev, "RX underrun\n");
 916         }
 917         if (val & S3C64XX_SPI_ST_TX_OVERRUN_ERR) {
 918                 clr |= S3C64XX_SPI_PND_TX_OVERRUN_CLR;
 919                 dev_err(&spi->dev, "TX overrun\n");
 920         }
 921         if (val & S3C64XX_SPI_ST_TX_UNDERRUN_ERR) {
 922                 clr |= S3C64XX_SPI_PND_TX_UNDERRUN_CLR;
 923                 dev_err(&spi->dev, "TX underrun\n");
 924         }
 925
 926         /* Clear the pending irq by setting and then clearing it */
 927         writel(clr, sdd->regs + S3C64XX_SPI_PENDING_CLR);
 928         writel(0, sdd->regs + S3C64XX_SPI_PENDING_CLR);
 929
 930         return IRQ_HANDLED;
 931 }
 932
 933 static void s3c64xx_spi_hwinit(struct s3c64xx_spi_driver_data *sdd)
 934 {
 935         struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
 936         void __iomem *regs = sdd->regs;
 937         unsigned int val;
 938
 939         sdd->cur_speed = 0;
 940
 941         if (sci->no_cs)
 942                 writel(0, sdd->regs + S3C64XX_SPI_SLAVE_SEL);
 943         else if (!(sdd->port_conf->quirks & S3C64XX_SPI_QUIRK_CS_AUTO))
 944                 writel(S3C64XX_SPI_SLAVE_SIG_INACT, sdd->regs + S3C64XX_SPI_SLAVE_SEL);
 945
 946         /* Disable Interrupts - we use Polling if not DMA mode */
 947         writel(0, regs + S3C64XX_SPI_INT_EN);
 948
 949         if (!sdd->port_conf->clk_from_cmu)
 950                 writel(sci->src_clk_nr << S3C64XX_SPI_CLKSEL_SRCSHFT,
 951                                 regs + S3C64XX_SPI_CLK_CFG);
 952         writel(0, regs + S3C64XX_SPI_MODE_CFG);
 953         writel(0, regs + S3C64XX_SPI_PACKET_CNT);
 954
 955         /* Clear any irq pending bits, should set and clear the bits */
 956         val = S3C64XX_SPI_PND_RX_OVERRUN_CLR |
 957                 S3C64XX_SPI_PND_RX_UNDERRUN_CLR |
 958                 S3C64XX_SPI_PND_TX_OVERRUN_CLR |
 959                 S3C64XX_SPI_PND_TX_UNDERRUN_CLR;
 960         writel(val, regs + S3C64XX_SPI_PENDING_CLR);
 961         writel(0, regs + S3C64XX_SPI_PENDING_CLR);
 962
 963         writel(0, regs + S3C64XX_SPI_SWAP_CFG);
 964
 965         val = readl(regs + S3C64XX_SPI_MODE_CFG);
 966         val &= ~S3C64XX_SPI_MODE_4BURST;
 967         val &= ~(S3C64XX_SPI_MAX_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF);
 968         val |= (S3C64XX_SPI_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF);
 969         writel(val, regs + S3C64XX_SPI_MODE_CFG);
 970
 971         s3c64xx_flush_fifo(sdd);
 972 }
 973
 974 #ifdef CONFIG_OF
 975 static struct s3c64xx_spi_info *s3c64xx_spi_parse_dt(struct device *dev)
 976 {
 977         struct s3c64xx_spi_info *sci;
 978         u32 temp;
 979
 980         sci = devm_kzalloc(dev, sizeof(*sci), GFP_KERNEL);
 981         if (!sci)
 982                 return ERR_PTR(-ENOMEM);
 983
 984         if (of_property_read_u32(dev->of_node, "samsung,spi-src-clk", &temp)) {
 985                 dev_warn(dev, "spi bus clock parent not specified, using clock at index 0 as parent\n");
 986                 sci->src_clk_nr = 0;
 987         } else {
 988                 sci->src_clk_nr = temp;
 989         }
 990
 991         if (of_property_read_u32(dev->of_node, "num-cs", &temp)) {
 992                 dev_warn(dev, "number of chip select lines not specified, assuming 1 chip select line\n");
 993                 sci->num_cs = 1;
 994         } else {
 995                 sci->num_cs = temp;
 996         }
 997
 998         sci->no_cs = of_property_read_bool(dev->of_node, "no-cs-readback");
 999
1000         return sci;
1001 }
1002 #else
1003 static struct s3c64xx_spi_info *s3c64xx_spi_parse_dt(struct device *dev)
1004 {
1005         return dev_get_platdata(dev);
1006 }
1007 #endif
1008
1009 static const struct of_device_id s3c64xx_spi_dt_match[];
1010
1011 static inline struct s3c64xx_spi_port_config *s3c64xx_spi_get_port_config(
1012                                                 struct platform_device *pdev)
1013 {
1014 #ifdef CONFIG_OF
1015         if (pdev->dev.of_node) {
1016                 const struct of_device_id *match;
1017                 match = of_match_node(s3c64xx_spi_dt_match, pdev->dev.of_node);
1018                 return (struct s3c64xx_spi_port_config *)match->data;
1019         }
1020 #endif
1021         return (struct s3c64xx_spi_port_config *)
1022                          platform_get_device_id(pdev)->driver_data;
1023 }
1024
1025 static int s3c64xx_spi_probe(struct platform_device *pdev)
1026 {
1027         struct resource *mem_res;
1028         struct s3c64xx_spi_driver_data *sdd;
1029         struct s3c64xx_spi_info *sci = dev_get_platdata(&pdev->dev);
1030         struct spi_master *master;
1031         int ret, irq;
1032         char clk_name[16];
1033
1034         if (!sci && pdev->dev.of_node) {
1035                 sci = s3c64xx_spi_parse_dt(&pdev->dev);
1036                 if (IS_ERR(sci))
1037                         return PTR_ERR(sci);
1038         }
1039
1040         if (!sci) {
1041                 dev_err(&pdev->dev, "platform_data missing!\n");
1042                 return -ENODEV;
1043         }
1044
1045         mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1046         if (mem_res == NULL) {
1047                 dev_err(&pdev->dev, "Unable to get SPI MEM resource\n");
1048                 return -ENXIO;
1049         }
1050
1051         irq = platform_get_irq(pdev, 0);
1052         if (irq < 0) {
1053                 dev_warn(&pdev->dev, "Failed to get IRQ: %d\n", irq);
1054                 return irq;
1055         }
1056
1057         master = spi_alloc_master(&pdev->dev,
1058                                 sizeof(struct s3c64xx_spi_driver_data));
1059         if (master == NULL) {
1060                 dev_err(&pdev->dev, "Unable to allocate SPI Master\n");
1061                 return -ENOMEM;
1062         }
1063
1064         platform_set_drvdata(pdev, master);
1065
1066         sdd = spi_master_get_devdata(master);
1067         sdd->port_conf = s3c64xx_spi_get_port_config(pdev);
1068         sdd->master = master;
1069         sdd->cntrlr_info = sci;
1070         sdd->pdev = pdev;
1071         sdd->sfr_start = mem_res->start;
1072         if (pdev->dev.of_node) {
1073                 ret = of_alias_get_id(pdev->dev.of_node, "spi");
1074                 if (ret < 0) {
1075                         dev_err(&pdev->dev, "failed to get alias id, errno %d\n",
1076                                 ret);
1077                         goto err_deref_master;
1078                 }
1079                 sdd->port_id = ret;
1080         } else {
1081                 sdd->port_id = pdev->id;
1082         }
1083
1084         sdd->cur_bpw = 8;
1085
1086         sdd->tx_dma.direction = DMA_MEM_TO_DEV;
1087         sdd->rx_dma.direction = DMA_DEV_TO_MEM;
1088
1089         master->dev.of_node = pdev->dev.of_node;
1090         master->bus_num = sdd->port_id;
1091         master->setup = s3c64xx_spi_setup;
1092         master->cleanup = s3c64xx_spi_cleanup;
1093         master->prepare_transfer_hardware = s3c64xx_spi_prepare_transfer;
1094         master->prepare_message = s3c64xx_spi_prepare_message;
1095         master->transfer_one = s3c64xx_spi_transfer_one;
1096         master->num_chipselect = sci->num_cs;
1097         master->dma_alignment = 8;
1098         master->bits_per_word_mask = SPI_BPW_MASK(32) | SPI_BPW_MASK(16) |
1099                                         SPI_BPW_MASK(8);
1100         /* the spi->mode bits understood by this driver: */
1101         master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
1102         master->auto_runtime_pm = true;
1103         if (!is_polling(sdd))
1104                 master->can_dma = s3c64xx_spi_can_dma;
1105
1106         sdd->regs = devm_ioremap_resource(&pdev->dev, mem_res);
1107         if (IS_ERR(sdd->regs)) {
1108                 ret = PTR_ERR(sdd->regs);
1109                 goto err_deref_master;
1110         }
1111
1112         if (sci->cfg_gpio && sci->cfg_gpio()) {
1113                 dev_err(&pdev->dev, "Unable to config gpio\n");
1114                 ret = -EBUSY;
1115                 goto err_deref_master;
1116         }
1117
1118         /* Setup clocks */
1119         sdd->clk = devm_clk_get(&pdev->dev, "spi");
1120         if (IS_ERR(sdd->clk)) {
1121                 dev_err(&pdev->dev, "Unable to acquire clock 'spi'\n");
1122                 ret = PTR_ERR(sdd->clk);
1123                 goto err_deref_master;
1124         }
1125
1126         ret = clk_prepare_enable(sdd->clk);
1127         if (ret) {
1128                 dev_err(&pdev->dev, "Couldn't enable clock 'spi'\n");
1129                 goto err_deref_master;
1130         }
1131
1132         sprintf(clk_name, "spi_busclk%d", sci->src_clk_nr);
1133         sdd->src_clk = devm_clk_get(&pdev->dev, clk_name);
1134         if (IS_ERR(sdd->src_clk)) {
1135                 dev_err(&pdev->dev,
1136                         "Unable to acquire clock '%s'\n", clk_name);
1137                 ret = PTR_ERR(sdd->src_clk);
1138                 goto err_disable_clk;
1139         }
1140
1141         ret = clk_prepare_enable(sdd->src_clk);
1142         if (ret) {
1143                 dev_err(&pdev->dev, "Couldn't enable clock '%s'\n", clk_name);
1144                 goto err_disable_clk;
1145         }
1146
1147         if (sdd->port_conf->clk_ioclk) {
1148                 sdd->ioclk = devm_clk_get(&pdev->dev, "spi_ioclk");
1149                 if (IS_ERR(sdd->ioclk)) {
1150                         dev_err(&pdev->dev, "Unable to acquire 'ioclk'\n");
1151                         ret = PTR_ERR(sdd->ioclk);
1152                         goto err_disable_src_clk;
1153                 }
1154
1155                 ret = clk_prepare_enable(sdd->ioclk);
1156                 if (ret) {
1157                         dev_err(&pdev->dev, "Couldn't enable clock 'ioclk'\n");
1158                         goto err_disable_src_clk;
1159                 }
1160         }
1161
1162         if (!is_polling(sdd)) {
1163                 /* Acquire DMA channels */
1164                 sdd->rx_dma.ch = dma_request_chan(&pdev->dev, "rx");
1165                 if (IS_ERR(sdd->rx_dma.ch)) {
1166                         dev_err(&pdev->dev, "Failed to get RX DMA channel\n");
1167                         ret = PTR_ERR(sdd->rx_dma.ch);
1168                         goto err_disable_io_clk;
1169                 }
1170                 sdd->tx_dma.ch = dma_request_chan(&pdev->dev, "tx");
1171                 if (IS_ERR(sdd->tx_dma.ch)) {
1172                         dev_err(&pdev->dev, "Failed to get TX DMA channel\n");
1173                         ret = PTR_ERR(sdd->tx_dma.ch);
1174                         goto err_release_rx_dma;
1175                 }
1176         }
1177
1178         pm_runtime_set_autosuspend_delay(&pdev->dev, AUTOSUSPEND_TIMEOUT);
1179         pm_runtime_use_autosuspend(&pdev->dev);
1180         pm_runtime_set_active(&pdev->dev);
1181         pm_runtime_enable(&pdev->dev);
1182         pm_runtime_get_sync(&pdev->dev);
1183
1184         /* Setup Deufult Mode */
1185         s3c64xx_spi_hwinit(sdd);
1186
1187         spin_lock_init(&sdd->lock);
1188         init_completion(&sdd->xfer_completion);
1189
1190         ret = devm_request_irq(&pdev->dev, irq, s3c64xx_spi_irq, 0,
1191                                 "spi-s3c64xx", sdd);
1192         if (ret != 0) {
1193                 dev_err(&pdev->dev, "Failed to request IRQ %d: %d\n",
1194                         irq, ret);
1195                 goto err_pm_put;
1196         }
1197
1198         writel(S3C64XX_SPI_INT_RX_OVERRUN_EN | S3C64XX_SPI_INT_RX_UNDERRUN_EN |
1199                S3C64XX_SPI_INT_TX_OVERRUN_EN | S3C64XX_SPI_INT_TX_UNDERRUN_EN,
1200                sdd->regs + S3C64XX_SPI_INT_EN);
1201
1202         ret = devm_spi_register_master(&pdev->dev, master);
1203         if (ret != 0) {
1204                 dev_err(&pdev->dev, "cannot register SPI master: %d\n", ret);
1205                 goto err_pm_put;
1206         }
1207
1208         dev_dbg(&pdev->dev, "Samsung SoC SPI Driver loaded for Bus SPI-%d with %d Slaves attached\n",
1209                                         sdd->port_id, master->num_chipselect);
1210         dev_dbg(&pdev->dev, "\tIOmem=[%pR]\tFIFO %dbytes\n",
1211                                         mem_res, (FIFO_LVL_MASK(sdd) >> 1) + 1);
1212
1213         pm_runtime_mark_last_busy(&pdev->dev);
1214         pm_runtime_put_autosuspend(&pdev->dev);
1215
1216         return 0;
1217
1218 err_pm_put:
1219         pm_runtime_put_noidle(&pdev->dev);
1220         pm_runtime_disable(&pdev->dev);
1221         pm_runtime_set_suspended(&pdev->dev);
1222
1223         if (!is_polling(sdd))
1224                 dma_release_channel(sdd->tx_dma.ch);
1225 err_release_rx_dma:
1226         if (!is_polling(sdd))
1227                 dma_release_channel(sdd->rx_dma.ch);
1228 err_disable_io_clk:
1229         clk_disable_unprepare(sdd->ioclk);
1230 err_disable_src_clk:
1231         clk_disable_unprepare(sdd->src_clk);
1232 err_disable_clk:
1233         clk_disable_unprepare(sdd->clk);
1234 err_deref_master:
1235         spi_master_put(master);
1236
1237         return ret;
1238 }
1239
1240 static int s3c64xx_spi_remove(struct platform_device *pdev)
1241 {
1242         struct spi_master *master = platform_get_drvdata(pdev);
1243         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
1244
1245         pm_runtime_get_sync(&pdev->dev);
1246
1247         writel(0, sdd->regs + S3C64XX_SPI_INT_EN);
1248
1249         if (!is_polling(sdd)) {
1250                 dma_release_channel(sdd->rx_dma.ch);
1251                 dma_release_channel(sdd->tx_dma.ch);
1252         }
1253
1254         clk_disable_unprepare(sdd->ioclk);
1255
1256         clk_disable_unprepare(sdd->src_clk);
1257
1258         clk_disable_unprepare(sdd->clk);
1259
1260         pm_runtime_put_noidle(&pdev->dev);
1261         pm_runtime_disable(&pdev->dev);
1262         pm_runtime_set_suspended(&pdev->dev);
1263
1264         return 0;
1265 }
1266
1267 #ifdef CONFIG_PM_SLEEP
1268 static int s3c64xx_spi_suspend(struct device *dev)
1269 {
1270         struct spi_master *master = dev_get_drvdata(dev);
1271         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
1272
1273         int ret = spi_master_suspend(master);
1274         if (ret)
1275                 return ret;
1276
1277         ret = pm_runtime_force_suspend(dev);
1278         if (ret < 0)
1279                 return ret;
1280
1281         sdd->cur_speed = 0; /* Output Clock is stopped */
1282
1283         return 0;
1284 }
1285
1286 static int s3c64xx_spi_resume(struct device *dev)
1287 {
1288         struct spi_master *master = dev_get_drvdata(dev);
1289         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
1290         struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
1291         int ret;
1292
1293         if (sci->cfg_gpio)
1294                 sci->cfg_gpio();
1295
1296         ret = pm_runtime_force_resume(dev);
1297         if (ret < 0)
1298                 return ret;
1299
1300         return spi_master_resume(master);
1301 }
1302 #endif /* CONFIG_PM_SLEEP */
1303
1304 #ifdef CONFIG_PM
1305 static int s3c64xx_spi_runtime_suspend(struct device *dev)
1306 {
1307         struct spi_master *master = dev_get_drvdata(dev);
1308         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
1309
1310         clk_disable_unprepare(sdd->clk);
1311         clk_disable_unprepare(sdd->src_clk);
1312         clk_disable_unprepare(sdd->ioclk);
1313
1314         return 0;
1315 }
1316
1317 static int s3c64xx_spi_runtime_resume(struct device *dev)
1318 {
1319         struct spi_master *master = dev_get_drvdata(dev);
1320         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
1321         int ret;
1322
1323         if (sdd->port_conf->clk_ioclk) {
1324                 ret = clk_prepare_enable(sdd->ioclk);
1325                 if (ret != 0)
1326                         return ret;
1327         }
1328
1329         ret = clk_prepare_enable(sdd->src_clk);
1330         if (ret != 0)
1331                 goto err_disable_ioclk;
1332
1333         ret = clk_prepare_enable(sdd->clk);
1334         if (ret != 0)
1335                 goto err_disable_src_clk;
1336
1337         s3c64xx_spi_hwinit(sdd);
1338
1339         return 0;
1340
1341 err_disable_src_clk:
1342         clk_disable_unprepare(sdd->src_clk);
1343 err_disable_ioclk:
1344         clk_disable_unprepare(sdd->ioclk);
1345
1346         return ret;
1347 }
1348 #endif /* CONFIG_PM */
1349
1350 static const struct dev_pm_ops s3c64xx_spi_pm = {
1351         SET_SYSTEM_SLEEP_PM_OPS(s3c64xx_spi_suspend, s3c64xx_spi_resume)
1352         SET_RUNTIME_PM_OPS(s3c64xx_spi_runtime_suspend,
1353                            s3c64xx_spi_runtime_resume, NULL)
1354 };
1355
1356 static struct s3c64xx_spi_port_config s3c2443_spi_port_config = {
1357         .fifo_lvl_mask  = { 0x7f },
1358         .rx_lvl_offset  = 13,
1359         .tx_st_done     = 21,
1360         .high_speed     = true,
1361 };
1362
1363 static struct s3c64xx_spi_port_config s3c6410_spi_port_config = {
1364         .fifo_lvl_mask  = { 0x7f, 0x7F },
1365         .rx_lvl_offset  = 13,
1366         .tx_st_done     = 21,
1367 };
1368
1369 static struct s3c64xx_spi_port_config s5pv210_spi_port_config = {
1370         .fifo_lvl_mask  = { 0x1ff, 0x7F },
1371         .rx_lvl_offset  = 15,
1372         .tx_st_done     = 25,
1373         .high_speed     = true,
1374 };
1375
1376 static struct s3c64xx_spi_port_config exynos4_spi_port_config = {
1377         .fifo_lvl_mask  = { 0x1ff, 0x7F, 0x7F },
1378         .rx_lvl_offset  = 15,
1379         .tx_st_done     = 25,
1380         .high_speed     = true,
1381         .clk_from_cmu   = true,
1382 };
1383
1384 static struct s3c64xx_spi_port_config exynos7_spi_port_config = {
1385         .fifo_lvl_mask  = { 0x1ff, 0x7F, 0x7F, 0x7F, 0x7F, 0x1ff},
1386         .rx_lvl_offset  = 15,
1387         .tx_st_done     = 25,
1388         .high_speed     = true,
1389         .clk_from_cmu   = true,
1390         .quirks         = S3C64XX_SPI_QUIRK_CS_AUTO,
1391 };
1392
1393 static struct s3c64xx_spi_port_config exynos5433_spi_port_config = {
1394         .fifo_lvl_mask  = { 0x1ff, 0x7f, 0x7f, 0x7f, 0x7f, 0x1ff},
1395         .rx_lvl_offset  = 15,
1396         .tx_st_done     = 25,
1397         .high_speed     = true,
1398         .clk_from_cmu   = true,
1399         .clk_ioclk      = true,
1400         .quirks         = S3C64XX_SPI_QUIRK_CS_AUTO,
1401 };
1402
1403 static const struct platform_device_id s3c64xx_spi_driver_ids[] = {
1404         {
1405                 .name           = "s3c2443-spi",
1406                 .driver_data    = (kernel_ulong_t)&s3c2443_spi_port_config,
1407         }, {
1408                 .name           = "s3c6410-spi",
1409                 .driver_data    = (kernel_ulong_t)&s3c6410_spi_port_config,
1410         },
1411         { },
1412 };
1413
1414 static const struct of_device_id s3c64xx_spi_dt_match[] = {
1415         { .compatible = "samsung,s3c2443-spi",
1416                         .data = (void *)&s3c2443_spi_port_config,
1417         },
1418         { .compatible = "samsung,s3c6410-spi",
1419                         .data = (void *)&s3c6410_spi_port_config,
1420         },
1421         { .compatible = "samsung,s5pv210-spi",
1422                         .data = (void *)&s5pv210_spi_port_config,
1423         },
1424         { .compatible = "samsung,exynos4210-spi",
1425                         .data = (void *)&exynos4_spi_port_config,
1426         },
1427         { .compatible = "samsung,exynos7-spi",
1428                         .data = (void *)&exynos7_spi_port_config,
1429         },
1430         { .compatible = "samsung,exynos5433-spi",
1431                         .data = (void *)&exynos5433_spi_port_config,
1432         },
1433         { },
1434 };
1435 MODULE_DEVICE_TABLE(of, s3c64xx_spi_dt_match);
1436
1437 static struct platform_driver s3c64xx_spi_driver = {
1438         .driver = {
1439                 .name   = "s3c64xx-spi",
1440                 .pm = &s3c64xx_spi_pm,
1441                 .of_match_table = of_match_ptr(s3c64xx_spi_dt_match),
1442         },
1443         .probe = s3c64xx_spi_probe,
1444         .remove = s3c64xx_spi_remove,
1445         .id_table = s3c64xx_spi_driver_ids,
1446 };
1447 MODULE_ALIAS("platform:s3c64xx-spi");
1448
1449 module_platform_driver(s3c64xx_spi_driver);
1450
1451 MODULE_AUTHOR("Jaswinder Singh <jassi.brar@samsung.com>");
1452 MODULE_DESCRIPTION("S3C64XX SPI Controller Driver");
1453 MODULE_LICENSE("GPL");