1 # SPDX-License-Identifier: GPL-2.0-only
3 # SPI driver configuration
9 The "Serial Peripheral Interface" is a low level synchronous
10 protocol. Chips that support SPI can have data transfer rates
11 up to several tens of Mbit/sec. Chips are addressed with a
12 controller and a chipselect. Most SPI slaves don't support
13 dynamic device discovery; some are even write-only or read-only.
15 SPI is widely used by microcontrollers to talk with sensors,
16 eeprom and flash memory, codecs and various other controller
17 chips, analog to digital (and d-to-a) converters, and more.
18 MMC and SD cards can be accessed using SPI protocol; and for
19 DataFlash cards used in MMC sockets, SPI must always be used.
21 SPI is one of a family of similar protocols using a four wire
22 interface (select, clock, data in, data out) including Microwire
23 (half duplex), SSP, SSI, and PSP. This driver framework should
24 work with most such devices and controllers.
29 bool "Debug support for SPI drivers"
30 depends on DEBUG_KERNEL
32 Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
33 sysfs, and debugfs support in SPI controller and protocol drivers.
36 # MASTER side ... talking to discrete SPI slave chips including microcontrollers
40 # bool "SPI Master Support"
44 If your system has an master-capable SPI controller (which
45 provides the clock and chipselect), you can enable that
46 controller and the protocol drivers for the SPI slave chips
52 bool "SPI memory extension"
54 Enable this option if you want to enable the SPI memory extension.
55 This extension is meant to simplify interaction with SPI memories
56 by providing a high-level interface to send memory-like commands.
58 comment "SPI Master Controller Drivers"
61 tristate "Altera SPI Controller"
64 This is the driver for the Altera SPI Controller.
67 tristate "Qualcomm Atheros AR934X/QCA95XX SPI controller driver"
68 depends on ATH79 || COMPILE_TEST
70 This enables support for the SPI controller present on the
71 Qualcomm Atheros AR934X/QCA95XX SoCs.
74 tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
75 depends on ATH79 || COMPILE_TEST
78 This enables support for the SPI controller present on the
79 Atheros AR71XX/AR724X/AR913X SoCs.
81 config SPI_ARMADA_3700
82 tristate "Marvell Armada 3700 SPI Controller"
83 depends on (ARCH_MVEBU && OF) || COMPILE_TEST
85 This enables support for the SPI controller present on the
86 Marvell Armada 3700 SoCs.
89 tristate "Atmel SPI Controller"
90 depends on ARCH_AT91 || COMPILE_TEST
93 This selects a driver for the Atmel SPI Controller, present on
97 tristate "Atmel USART Controller SPI driver"
98 depends on (ARCH_AT91 || COMPILE_TEST)
99 depends on MFD_AT91_USART
101 This selects a driver for the AT91 USART Controller as SPI Master,
102 present on AT91 and SAMA5 SoC series.
104 config SPI_ATMEL_QUADSPI
105 tristate "Atmel Quad SPI Controller"
106 depends on ARCH_AT91 || COMPILE_TEST
107 depends on OF && HAS_IOMEM
109 This enables support for the Quad SPI controller in master mode.
110 This driver does not support generic SPI. The implementation only
111 supports spi-mem interface.
114 tristate "Au1550/Au1200/Au1300 SPI Controller"
115 depends on MIPS_ALCHEMY
118 If you say yes to this option, support will be included for the
119 PSC SPI controller found on Au1550, Au1200 and Au1300 series.
121 config SPI_AXI_SPI_ENGINE
122 tristate "Analog Devices AXI SPI Engine controller"
125 This enables support for the Analog Devices AXI SPI Engine SPI controller.
126 It is part of the SPI Engine framework that is used in some Analog Devices
127 reference designs for FPGAs.
130 tristate "BCM2835 SPI controller"
132 depends on ARCH_BCM2835 || ARCH_BRCMSTB || COMPILE_TEST
134 This selects a driver for the Broadcom BCM2835 SPI master.
136 The BCM2835 contains two types of SPI master controller; the
137 "universal SPI master", and the regular SPI controller. This driver
138 is for the regular SPI controller. Slave mode operation is not also
141 config SPI_BCM2835AUX
142 tristate "BCM2835 SPI auxiliary controller"
143 depends on ((ARCH_BCM2835 || ARCH_BRCMSTB) && GPIOLIB) || COMPILE_TEST
145 This selects a driver for the Broadcom BCM2835 SPI aux master.
147 The BCM2835 contains two types of SPI master controller; the
148 "universal SPI master", and the regular SPI controller.
149 This driver is for the universal/auxiliary SPI controller.
152 tristate "Broadcom BCM63xx SPI controller"
153 depends on BCM63XX || BMIPS_GENERIC || COMPILE_TEST
155 Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
157 config SPI_BCM63XX_HSSPI
158 tristate "Broadcom BCM63XX HS SPI controller driver"
159 depends on BCM63XX || BMIPS_GENERIC || ARCH_BCM_63XX || COMPILE_TEST
161 This enables support for the High Speed SPI controller present on
162 newer Broadcom BCM63XX SoCs.
165 tristate "Broadcom BSPI and MSPI controller support"
166 depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || \
167 BMIPS_GENERIC || COMPILE_TEST
168 default ARCH_BCM_IPROC
170 Enables support for the Broadcom SPI flash and MSPI controller.
171 Select this option for any one of BRCMSTB, iProc NSP and NS2 SoCs
172 based platforms. This driver works for both SPI master for SPI NOR
173 flash device as well as MSPI device.
176 tristate "Utilities for Bitbanging SPI masters"
178 With a few GPIO pins, your system can bitbang the SPI protocol.
179 Select this to get SPI support through I/O pins (GPIO, parallel
180 port, etc). Or, some systems' SPI master controller drivers use
181 this code to manage the per-word or per-transfer accesses to the
182 hardware shift registers.
184 This is library code, and is automatically selected by drivers that
185 need it. You only need to select this explicitly to support driver
186 modules that aren't part of this kernel tree.
189 tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
193 This uses a custom parallel port cable to connect to an AVR
194 Butterfly <http://www.atmel.com/products/avr/butterfly>, an
195 inexpensive battery powered microcontroller evaluation board.
196 This same cable can be used to flash new firmware.
199 tristate "Cadence SPI controller"
201 This selects the Cadence SPI controller master driver
202 used by Xilinx Zynq and ZynqMP.
204 config SPI_CADENCE_QUADSPI
205 tristate "Cadence Quad SPI controller"
206 depends on OF && (ARM || ARM64 || COMPILE_TEST)
208 Enable support for the Cadence Quad SPI Flash controller.
210 Cadence QSPI is a specialized controller for connecting an SPI
211 Flash over 1/2/4-bit wide bus. Enable this option if you have a
212 device with a Cadence QSPI controller and want to access the
213 Flash as an MTD device.
216 tristate "CLPS711X host SPI controller"
217 depends on ARCH_CLPS711X || COMPILE_TEST
219 This enables dedicated general purpose SPI/Microwire1-compatible
220 master mode interface (SSI1) for CLPS711X-based CPUs.
222 config SPI_COLDFIRE_QSPI
223 tristate "Freescale Coldfire QSPI controller"
224 depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
226 This enables support for the Coldfire QSPI controller in master
230 tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
231 depends on ARCH_DAVINCI || ARCH_KEYSTONE
234 SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
236 config SPI_DESIGNWARE
237 tristate "DesignWare SPI controller core support"
240 general driver for SPI controller core from DesignWare
245 bool "DMA support for DW SPI controller"
248 tristate "PCI interface driver for DW SPI core"
252 tristate "Memory-mapped io interface driver for DW SPI core"
256 tristate "Baikal-T1 SPI driver for DW SPI core"
257 depends on MIPS_BAIKAL_T1 || COMPILE_TEST
261 Baikal-T1 SoC is equipped with three DW APB SSI-based MMIO SPI
262 controllers. Two of them are pretty much normal: with IRQ, DMA,
263 FIFOs of 64 words depth, 4x CSs, but the third one as being a
264 part of the Baikal-T1 System Boot Controller has got a very
265 limited resources: no IRQ, no DMA, only a single native
266 chip-select and Tx/Rx FIFO with just 8 words depth available.
267 The later one is normally connected to an external SPI-nor flash
268 of 128Mb (in general can be of bigger size).
270 config SPI_DW_BT1_DIRMAP
271 bool "Directly mapped Baikal-T1 Boot SPI flash support"
272 depends on SPI_DW_BT1
274 Directly mapped SPI flash memory is an interface specific to the
275 Baikal-T1 System Boot Controller. It is a 16MB MMIO region, which
276 can be used to access a peripheral memory device just by
277 reading/writing data from/to it. Note that the system APB bus
278 will stall during each IO from/to the dirmap region until the
279 operation is finished. So try not to use it concurrently with
280 time-critical tasks (like the SPI memory operations implemented
286 tristate "Diolan DLN-2 USB SPI adapter"
289 If you say yes to this option, support will be included for Diolan
290 DLN2, a USB to SPI interface.
292 This driver can also be built as a module. If so, the module
293 will be called spi-dln2.
296 tristate "EFM32 SPI controller"
297 depends on OF && ARM && (ARCH_EFM32 || COMPILE_TEST)
300 Driver for the spi controller found on Energy Micro's EFM32 SoCs.
303 tristate "Cirrus Logic EP93xx SPI controller"
304 depends on ARCH_EP93XX || COMPILE_TEST
306 This enables using the Cirrus EP93xx SPI controller in master
310 bool "Falcon SPI controller support"
311 depends on SOC_FALCON
313 The external bus unit (EBU) found on the FALC-ON SoC has SPI
314 emulation that is designed for serial flash access. This driver
315 has only been tested with m25p80 type chips. The hardware has no
316 support for other types of SPI peripherals.
319 tristate "FSI SPI driver"
322 This enables support for the driver for FSI bus attached SPI
326 tristate "Freescale i.MX LPSPI controller"
327 depends on ARCH_MXC || COMPILE_TEST
329 This enables Freescale i.MX LPSPI controllers in master mode.
331 config SPI_FSL_QUADSPI
332 tristate "Freescale QSPI controller"
333 depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
336 This enables support for the Quad SPI controller in master mode.
337 Up to four flash chips can be connected on two buses with two
339 This controller does not support generic SPI messages. It only
340 supports the high-level SPI memory interface.
342 config SPI_HISI_SFC_V3XX
343 tristate "HiSilicon SPI NOR Flash Controller for Hi16XX chipsets"
344 depends on (ARM64 && ACPI) || COMPILE_TEST
347 This enables support for HiSilicon v3xx SPI NOR flash controller
348 found in hi16xx chipsets.
350 config SPI_NXP_FLEXSPI
351 tristate "NXP Flex SPI controller"
352 depends on ARCH_LAYERSCAPE || HAS_IOMEM
354 This enables support for the Flex SPI controller in master mode.
355 Up to four slave devices can be connected on two buses with two
357 This controller does not support generic SPI messages and only
358 supports the high-level SPI memory interface.
361 tristate "GPIO-based bitbanging SPI Master"
362 depends on GPIOLIB || COMPILE_TEST
365 This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
366 interface to manage MOSI, MISO, SCK, and chipselect signals. SPI
367 slaves connected to a bus using this driver are configured as usual,
368 except that the spi_board_info.controller_data holds the GPIO number
369 for the chipselect used by this controller driver.
371 Note that this driver often won't achieve even 1 Mbit/sec speeds,
372 making it unusually slow for SPI. If your platform can inline
373 GPIO operations, you should be able to leverage that for better
374 speed with a custom version of this driver; see the source code.
377 tristate "IMG SPFI controller"
378 depends on MIPS || COMPILE_TEST
380 This enables support for the SPFI master controller found on
384 tristate "Freescale i.MX SPI controllers"
385 depends on ARCH_MXC || COMPILE_TEST
388 This enables support for the Freescale i.MX SPI controllers.
391 tristate "J-Core SPI Master"
392 depends on OF && (SUPERH || COMPILE_TEST)
394 This enables support for the SPI master controller in the J-Core
395 synthesizable, open source SoC.
398 tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
402 This driver supports the NS LM70 LLP Evaluation Board,
403 which interfaces to an LM70 temperature sensor using
406 config SPI_LP8841_RTC
407 tristate "ICP DAS LP-8841 SPI Controller for RTC"
408 depends on MACH_PXA27X_DT || COMPILE_TEST
410 This driver provides an SPI master device to drive Maxim
411 DS-1302 real time clock.
413 Say N here unless you plan to run the kernel on an ICP DAS
414 LP-8x4x industrial computer.
417 tristate "Freescale MPC52xx SPI (non-PSC) controller support"
418 depends on PPC_MPC52xx
420 This drivers supports the MPC52xx SPI controller in master SPI
423 config SPI_MPC52xx_PSC
424 tristate "Freescale MPC52xx PSC SPI controller"
425 depends on PPC_MPC52xx
427 This enables using the Freescale MPC52xx Programmable Serial
428 Controller in master SPI mode.
430 config SPI_MPC512x_PSC
431 tristate "Freescale MPC512x PSC SPI controller"
432 depends on PPC_MPC512x
434 This enables using the Freescale MPC5121 Programmable Serial
435 Controller in SPI master mode.
446 tristate "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller"
449 select SPI_FSL_CPM if FSL_SOC
451 This enables using the Freescale SPI controllers in master mode.
452 MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
453 MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
454 This also enables using the Aeroflex Gaisler GRLIB SPI controller in
458 tristate "Freescale DSPI controller"
460 depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || M5441x || COMPILE_TEST
462 This enables support for the Freescale DSPI controller in master
463 mode. VF610, LS1021A and ColdFire platforms uses the controller.
466 tristate "Freescale eSPI controller"
469 This enables using the Freescale eSPI controllers in master mode.
470 From MPC8536, 85xx platform uses the controller, and all P10xx,
471 P20xx, P30xx,P40xx, P50xx uses this controller.
473 config SPI_MESON_SPICC
474 tristate "Amlogic Meson SPICC controller"
475 depends on COMMON_CLK
476 depends on ARCH_MESON || COMPILE_TEST
478 This enables master mode support for the SPICC (SPI communication
479 controller) available in Amlogic Meson SoCs.
481 config SPI_MESON_SPIFC
482 tristate "Amlogic Meson SPIFC controller"
483 depends on ARCH_MESON || COMPILE_TEST
486 This enables master mode support for the SPIFC (SPI flash
487 controller) available in Amlogic Meson SoCs.
490 tristate "MediaTek SPI controller"
491 depends on ARCH_MEDIATEK || COMPILE_TEST
493 This selects the MediaTek(R) SPI bus driver.
494 If you want to use MediaTek(R) SPI interface,
495 say Y or M here.If you are not sure, say N.
496 SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
499 tristate "MediaTek MT7621 SPI Controller"
500 depends on RALINK || COMPILE_TEST
502 This selects a driver for the MediaTek MT7621 SPI Controller.
505 tristate "MediaTek SPI NOR controller"
506 depends on ARCH_MEDIATEK || COMPILE_TEST
508 This enables support for SPI NOR controller found on MediaTek
509 ARM SoCs. This is a controller specifically for SPI NOR flash.
510 It can perform generic SPI transfers up to 6 bytes via generic
511 SPI interface as well as several SPI NOR specific instructions
512 via SPI MEM interface.
515 tristate "Nuvoton NPCM FLASH Interface Unit"
516 depends on ARCH_NPCM || COMPILE_TEST
517 depends on OF && HAS_IOMEM
519 This enables support for the Flash Interface Unit SPI controller
521 This driver does not support generic SPI. The implementation only
522 supports spi-mem interface.
525 tristate "Nuvoton NPCM PSPI Controller"
526 depends on ARCH_NPCM || COMPILE_TEST
528 This driver provides support for Nuvoton NPCM BMC
529 Peripheral SPI controller in master mode.
531 config SPI_LANTIQ_SSC
532 tristate "Lantiq SSC SPI controller"
533 depends on LANTIQ || X86 || COMPILE_TEST
535 This driver supports the Lantiq SSC SPI controller in master
536 mode. This controller is found on Intel (former Lantiq) SoCs like
537 the Danube, Falcon, xRX200, xRX300, Lightning Mountain.
540 tristate "OpenCores tiny SPI"
541 depends on GPIOLIB || COMPILE_TEST
544 This is the driver for OpenCores tiny SPI master controller.
547 tristate "Cavium OCTEON SPI controller"
548 depends on CAVIUM_OCTEON_SOC
550 SPI host driver for the hardware found on some Cavium OCTEON
553 config SPI_OMAP_UWIRE
554 tristate "OMAP1 MicroWire"
555 depends on ARCH_OMAP1
558 This hooks up to the MicroWire controller on OMAP1 chips.
561 tristate "McSPI driver for OMAP"
562 depends on ARCH_OMAP2PLUS || ARCH_K3 || COMPILE_TEST
565 SPI master controller for OMAP24XX and later Multichannel SPI
569 tristate "DRA7xxx QSPI controller support"
570 depends on ARCH_OMAP2PLUS || COMPILE_TEST
572 QSPI master controller for DRA7xxx used for flash devices.
573 This device supports single, dual and quad read support, while
574 it only supports single write mode.
577 tristate "OMAP SPI 100K"
578 depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST
580 OMAP SPI 100K master controller for omap7xx boards.
583 tristate "Orion SPI master"
584 depends on PLAT_ORION || ARCH_MVEBU || COMPILE_TEST
586 This enables using the SPI master controller on the Orion
590 tristate "Microchip PIC32 series SPI"
591 depends on MACH_PIC32 || COMPILE_TEST
593 SPI driver for Microchip PIC32 SPI master controller.
596 tristate "Microchip PIC32 Quad SPI driver"
597 depends on MACH_PIC32 || COMPILE_TEST
599 SPI driver for PIC32 Quad SPI controller.
602 tristate "ARM AMBA PL022 SSP controller"
604 default y if ARCH_REALVIEW
605 default y if INTEGRATOR_IMPD1
606 default y if ARCH_VERSATILE
608 This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
609 controller. If you have an embedded system with an AMBA(R)
610 bus and a PL022 controller, say Y or M here.
613 tristate "PPC4xx SPI Controller"
614 depends on PPC32 && 4xx
617 This selects a driver for the PPC4xx SPI Controller.
620 tristate "PXA2xx SSP SPI master"
621 depends on ARCH_PXA || ARCH_MMP || PCI || ACPI || COMPILE_TEST
622 select PXA_SSP if ARCH_PXA || ARCH_MMP
624 This enables using a PXA2xx or Sodaville SSP port as a SPI master
625 controller. The driver can be configured to use any SSP port and
626 additional documentation can be found a Documentation/spi/pxa2xx.rst.
628 config SPI_PXA2XX_PCI
629 def_tristate SPI_PXA2XX && PCI && COMMON_CLK
632 tristate "Rockchip SPI controller driver"
634 This selects a driver for Rockchip SPI controller.
636 If you say yes to this option, support will be included for
637 RK3066, RK3188 and RK3288 families of SPI controller.
638 Rockchip SPI controller support DMA transport and PIO mode.
639 The main usecase of this controller is to use spi flash as boot
643 tristate "Mikrotik RB4XX SPI master"
644 depends on SPI_MASTER && ATH79
646 SPI controller driver for the Mikrotik RB4xx series boards.
649 tristate "Renesas RPC-IF SPI driver"
650 depends on RENESAS_RPCIF
652 SPI driver for Renesas R-Car Gen3 RPC-IF.
655 tristate "Renesas RSPI/QSPI controller"
656 depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
658 SPI driver for Renesas RSPI and QSPI blocks.
661 tristate "QTI QSPI controller"
664 QSPI(Quad SPI) driver for Qualcomm QSPI controller.
667 tristate "Qualcomm SPI controller with QUP interface"
668 depends on ARCH_QCOM || COMPILE_TEST
670 Qualcomm Universal Peripheral (QUP) core is an AHB slave that
671 provides a common data path (an output FIFO and an input FIFO)
672 for serial peripheral interface (SPI) mini-core. SPI in master
673 mode supports up to 50MHz, up to four chip selects, programmable
674 data path from 4 bits to 32 bits and numerous protocol variants.
676 This driver can also be built as a module. If so, the module
677 will be called spi_qup.
680 tristate "Qualcomm GENI based SPI controller"
681 depends on QCOM_GENI_SE
683 This driver supports GENI serial engine based SPI controller in
684 master mode on the Qualcomm Technologies Inc.'s SoCs. If you say
685 yes to this option, support will be included for the built-in SPI
686 interface on the Qualcomm Technologies Inc.'s SoCs.
688 This driver can also be built as a module. If so, the module
689 will be called spi-geni-qcom.
692 tristate "Samsung S3C24XX series SPI"
693 depends on ARCH_S3C24XX
696 SPI driver for Samsung S3C24XX series ARM SoCs
698 config SPI_S3C24XX_FIQ
699 bool "S3C24XX driver with FIQ pseudo-DMA"
700 depends on SPI_S3C24XX
703 Enable FIQ support for the S3C24XX SPI driver to provide pseudo
704 DMA by using the fast-interrupt request framework, This allows
705 the driver to get DMA-like performance when there are either
706 no free DMA channels, or when doing transfers that required both
707 TX and RX data paths.
710 tristate "Samsung S3C64XX series type SPI"
711 depends on (PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST)
713 SPI driver for Samsung S3C64XX and newer SoCs.
716 tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
719 SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
722 tristate "SuperH MSIOF SPI controller"
724 depends on ARCH_SHMOBILE || ARCH_RENESAS || COMPILE_TEST
726 SPI driver for SuperH and SH Mobile MSIOF blocks.
729 tristate "SuperH SPI controller"
730 depends on SUPERH || COMPILE_TEST
732 SPI driver for SuperH SPI blocks.
735 tristate "SuperH SCI SPI controller"
739 SPI driver for SuperH SCI blocks.
742 tristate "SuperH HSPI controller"
743 depends on ARCH_RENESAS || COMPILE_TEST
745 SPI driver for SuperH HSPI blocks.
748 tristate "SiFive SPI controller"
751 This exposes the SPI controller IP from SiFive.
754 tristate "CSR SiRFprimaII SPI controller"
758 SPI driver for CSR SiRFprimaII SoCs
760 config SPI_SLAVE_MT27XX
761 tristate "MediaTek SPI slave device"
762 depends on ARCH_MEDIATEK || COMPILE_TEST
765 This selects the MediaTek(R) SPI slave device driver.
766 If you want to use MediaTek(R) SPI slave interface,
767 say Y or M here.If you are not sure, say N.
768 SPI slave drivers for Mediatek MT27XX series ARM SoCs.
771 tristate "Spreadtrum SPI controller"
772 depends on ARCH_SPRD || COMPILE_TEST
774 SPI driver for Spreadtrum SoCs.
777 tristate "Spreadtrum ADI controller"
778 depends on ARCH_SPRD || COMPILE_TEST
779 depends on HWSPINLOCK || (COMPILE_TEST && !HWSPINLOCK)
781 ADI driver based on SPI for Spreadtrum SoCs.
784 tristate "STMicroelectronics STM32 SPI controller"
785 depends on ARCH_STM32 || COMPILE_TEST
787 SPI driver for STMicroelectronics STM32 SoCs.
789 STM32 SPI controller supports DMA and PIO modes. When DMA
790 is not available, the driver automatically falls back to
793 config SPI_STM32_QSPI
794 tristate "STMicroelectronics STM32 QUAD SPI controller"
795 depends on ARCH_STM32 || COMPILE_TEST
798 This enables support for the Quad SPI controller in master mode.
799 This driver does not support generic SPI. The implementation only
800 supports spi-mem interface.
803 tristate "STMicroelectronics SPI SSC-based driver"
804 depends on ARCH_STI || COMPILE_TEST
806 STMicroelectronics SoCs support for SPI. If you say yes to
807 this option, support will be included for the SSC driven SPI.
810 tristate "Allwinner A10 SoCs SPI controller"
811 depends on ARCH_SUNXI || COMPILE_TEST
813 SPI driver for Allwinner sun4i, sun5i and sun7i SoCs
816 tristate "Allwinner A31 SPI controller"
817 depends on ARCH_SUNXI || COMPILE_TEST
818 depends on RESET_CONTROLLER
820 This enables using the SPI controller on the Allwinner A31 SoCs.
823 tristate "Socionext's SynQuacer HighSpeed SPI controller"
824 depends on ARCH_SYNQUACER || COMPILE_TEST
826 SPI driver for Socionext's High speed SPI controller which provides
827 various operating modes for interfacing to serial peripheral devices
828 that use the de-facto standard SPI protocol.
830 It also supports the new dual-bit and quad-bit SPI protocol.
833 tristate "Macronix MX25F0A SPI controller"
834 depends on SPI_MASTER
836 This selects the Macronix MX25F0A SPI controller driver.
839 tristate "Freescale MXS SPI controller"
843 SPI driver for Freescale MXS devices.
846 tristate "NVIDIA Tegra114 SPI Controller"
847 depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
848 depends on RESET_CONTROLLER
850 SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
851 is different than the older SoCs SPI controller and also register interface
852 get changed with this controller.
854 config SPI_TEGRA20_SFLASH
855 tristate "Nvidia Tegra20 Serial flash Controller"
856 depends on ARCH_TEGRA || COMPILE_TEST
857 depends on RESET_CONTROLLER
859 SPI driver for Nvidia Tegra20 Serial flash Controller interface.
860 The main usecase of this controller is to use spi flash as boot
863 config SPI_TEGRA20_SLINK
864 tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
865 depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
866 depends on RESET_CONTROLLER
868 SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
871 tristate "Cavium ThunderX SPI controller"
872 depends on PCI && 64BIT && (ARM64 || COMPILE_TEST)
874 SPI host driver for the hardware found on Cavium ThunderX
877 config SPI_TOPCLIFF_PCH
878 tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
879 depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
881 SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
882 used in some x86 embedded processors.
884 This driver also supports the ML7213/ML7223/ML7831, a companion chip
885 for the Atom E6xx series and compatible with the Intel EG20T PCH.
888 tristate "Toshiba TXx9 SPI controller"
889 depends on GPIOLIB && (CPU_TX49XX || COMPILE_TEST)
891 SPI driver for Toshiba TXx9 MIPS SoCs
894 tristate "Socionext UniPhier SPI Controller"
895 depends on (ARCH_UNIPHIER || COMPILE_TEST) && OF
898 This enables a driver for the Socionext UniPhier SoC SCSSI SPI controller.
900 UniPhier SoCs have SCSSI and MCSSI SPI controllers.
901 Every UniPhier SoC has SCSSI which supports single channel.
902 Older UniPhier Pro4/Pro5 also has MCSSI which support multiple channels.
903 This driver supports SCSSI only.
905 If your SoC supports SCSSI, say Y here.
908 tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
911 Support for the SPI-I2C bridge found on the Analog Devices
912 AD-FMCOMMS1-EBZ board.
915 tristate "Xilinx SPI controller common module"
919 This exposes the SPI controller IP from the Xilinx EDK.
921 See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
922 Product Specification document (DS464) for hardware details.
924 Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
927 tristate "Netlogic XLP SPI controller driver"
928 depends on CPU_XLP || ARCH_THUNDER2 || COMPILE_TEST
930 Enable support for the SPI controller on the Netlogic XLP SoCs.
931 Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, XLP9XX
934 If you have a Netlogic XLP platform say Y here.
937 config SPI_XTENSA_XTFPGA
938 tristate "Xtensa SPI controller for xtfpga"
939 depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
942 SPI driver for xtfpga SPI master controller.
944 This simple SPI master controller is built into xtfpga bitstreams
945 and is used to control daughterboard audio codec. It always transfers
946 16 bit words in SPI mode 0, automatically asserting CS on transfer
947 start and deasserting on end.
950 tristate "Xilinx Zynq QSPI controller"
951 depends on ARCH_ZYNQ || COMPILE_TEST
953 This enables support for the Zynq Quad SPI controller
955 This controller only supports SPI memory interface.
957 config SPI_ZYNQMP_GQSPI
958 tristate "Xilinx ZynqMP GQSPI controller"
959 depends on (SPI_MASTER && HAS_DMA) || COMPILE_TEST
961 Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
964 tristate "AMD SPI controller"
965 depends on SPI_MASTER || COMPILE_TEST
967 Enables SPI controller driver for AMD SoC.
970 # Add new SPI master controllers in alphabetical order above this line
973 comment "SPI Multiplexer support"
976 tristate "SPI multiplexer support"
979 This adds support for SPI multiplexers. Each SPI mux will be
980 accessible as a SPI controller, the devices behind the mux will appear
981 to be chip selects on this controller. It is still necessary to
982 select one or more specific mux-controller drivers.
985 # There are lots of SPI device types, with sensors and memory
986 # being probably the most widely used ones.
988 comment "SPI Protocol Masters"
991 tristate "User mode SPI device driver support"
993 This supports user mode SPI protocol drivers.
995 Note that this application programming interface is EXPERIMENTAL
996 and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
998 config SPI_LOOPBACK_TEST
999 tristate "spi loopback test framework support"
1002 This enables the SPI loopback testing framework driver
1004 primarily used for development of spi_master drivers
1005 and to detect regressions
1008 tristate "Infineon TLE62X0 (for power switching)"
1011 SPI driver for Infineon TLE62X0 series line driver chips,
1012 such as the TLE6220, TLE6230 and TLE6240. This provides a
1013 sysfs interface, with each line presented as a kind of GPIO
1014 exposing both switch control and diagnostic feedback.
1017 # Add new SPI protocol masters in alphabetical order above this line
1023 # SLAVE side ... listening to other SPI masters
1027 bool "SPI slave protocol handlers"
1029 If your system has a slave-capable SPI controller, you can enable
1030 slave protocol handlers.
1034 config SPI_SLAVE_TIME
1035 tristate "SPI slave handler reporting boot up time"
1037 SPI slave handler responding with the time of reception of the last
1040 config SPI_SLAVE_SYSTEM_CONTROL
1041 tristate "SPI slave handler controlling system state"
1043 SPI slave handler to allow remote control of system reboot, power
1044 off, halt, and suspend.
1049 def_bool ACPI || OF_DYNAMIC || SPI_SLAVE