drivers/serial/sunsab.c

   1 /* sunsab.c: ASYNC Driver for the SIEMENS SAB82532 DUSCC.
   2  *
   3  * Copyright (C) 1997  Eddie C. Dost  (ecd@skynet.be)
   4  * Copyright (C) 2002  David S. Miller (davem@redhat.com)
   5  *
   6  * Rewrote buffer handling to use CIRC(Circular Buffer) macros.
   7  *   Maxim Krasnyanskiy <maxk@qualcomm.com>
   8  *
   9  * Fixed to use tty_get_baud_rate, and to allow for arbitrary baud
  10  * rates to be programmed into the UART.  Also eliminated a lot of
  11  * duplicated code in the console setup.
  12  *   Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12
  13  *
  14  * Ported to new 2.5.x UART layer.
  15  *   David S. Miller <davem@redhat.com>
  16  */
  17
  18 #include <linux/config.h>
  19 #include <linux/module.h>
  20 #include <linux/kernel.h>
  21 #include <linux/sched.h>
  22 #include <linux/errno.h>
  23 #include <linux/tty.h>
  24 #include <linux/tty_flip.h>
  25 #include <linux/major.h>
  26 #include <linux/string.h>
  27 #include <linux/ptrace.h>
  28 #include <linux/ioport.h>
  29 #include <linux/circ_buf.h>
  30 #include <linux/serial.h>
  31 #include <linux/sysrq.h>
  32 #include <linux/console.h>
  33 #include <linux/spinlock.h>
  34 #include <linux/slab.h>
  35 #include <linux/delay.h>
  36 #include <linux/init.h>
  37
  38 #include <asm/io.h>
  39 #include <asm/irq.h>
  40 #include <asm/oplib.h>
  41 #include <asm/ebus.h>
  42
  43 #if defined(CONFIG_SERIAL_SUNZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
  44 #define SUPPORT_SYSRQ
  45 #endif
  46
  47 #include <linux/serial_core.h>
  48
  49 #include "suncore.h"
  50 #include "sunsab.h"
  51
  52 struct uart_sunsab_port {
  53         struct uart_port                port;           /* Generic UART port    */
  54         union sab82532_async_regs       __iomem *regs;  /* Chip registers       */
  55         unsigned long                   irqflags;       /* IRQ state flags      */
  56         int                             dsr;            /* Current DSR state    */
  57         unsigned int                    cec_timeout;    /* Chip poll timeout... */
  58         unsigned int                    tec_timeout;    /* likewise             */
  59         unsigned char                   interrupt_mask0;/* ISR0 masking         */
  60         unsigned char                   interrupt_mask1;/* ISR1 masking         */
  61         unsigned char                   pvr_dtr_bit;    /* Which PVR bit is DTR */
  62         unsigned char                   pvr_dsr_bit;    /* Which PVR bit is DSR */
  63         int                             type;           /* SAB82532 version     */
  64
  65         /* Setting configuration bits while the transmitter is active
  66          * can cause garbage characters to get emitted by the chip.
  67          * Therefore, we cache such writes here and do the real register
  68          * write the next time the transmitter becomes idle.
  69          */
  70         unsigned int                    cached_ebrg;
  71         unsigned char                   cached_mode;
  72         unsigned char                   cached_pvr;
  73         unsigned char                   cached_dafo;
  74 };
  75
  76 /*
  77  * This assumes you have a 29.4912 MHz clock for your UART.
  78  */
  79 #define SAB_BASE_BAUD ( 29491200 / 16 )
  80
  81 static char *sab82532_version[16] = {
  82         "V1.0", "V2.0", "V3.2", "V(0x03)",
  83         "V(0x04)", "V(0x05)", "V(0x06)", "V(0x07)",
  84         "V(0x08)", "V(0x09)", "V(0x0a)", "V(0x0b)",
  85         "V(0x0c)", "V(0x0d)", "V(0x0e)", "V(0x0f)"
  86 };
  87
  88 #define SAB82532_MAX_TEC_TIMEOUT 200000 /* 1 character time (at 50 baud) */
  89 #define SAB82532_MAX_CEC_TIMEOUT  50000 /* 2.5 TX CLKs (at 50 baud) */
  90
  91 #define SAB82532_RECV_FIFO_SIZE 32      /* Standard async fifo sizes */
  92 #define SAB82532_XMIT_FIFO_SIZE 32
  93
  94 static __inline__ void sunsab_tec_wait(struct uart_sunsab_port *up)
  95 {
  96         int timeout = up->tec_timeout;
  97
  98         while ((readb(&up->regs->r.star) & SAB82532_STAR_TEC) && --timeout)
  99                 udelay(1);
 100 }
 101
 102 static __inline__ void sunsab_cec_wait(struct uart_sunsab_port *up)
 103 {
 104         int timeout = up->cec_timeout;
 105
 106         while ((readb(&up->regs->r.star) & SAB82532_STAR_CEC) && --timeout)
 107                 udelay(1);
 108 }
 109
 110 static struct tty_struct *
 111 receive_chars(struct uart_sunsab_port *up,
 112               union sab82532_irq_status *stat,
 113               struct pt_regs *regs)
 114 {
 115         struct tty_struct *tty = NULL;
 116         unsigned char buf[32];
 117         int saw_console_brk = 0;
 118         int free_fifo = 0;
 119         int count = 0;
 120         int i;
 121
 122         if (up->port.info != NULL)              /* Unopened serial console */
 123                 tty = up->port.info->tty;
 124
 125         /* Read number of BYTES (Character + Status) available. */
 126         if (stat->sreg.isr0 & SAB82532_ISR0_RPF) {
 127                 count = SAB82532_RECV_FIFO_SIZE;
 128                 free_fifo++;
 129         }
 130
 131         if (stat->sreg.isr0 & SAB82532_ISR0_TCD) {
 132                 count = readb(&up->regs->r.rbcl) & (SAB82532_RECV_FIFO_SIZE - 1);
 133                 free_fifo++;
 134         }
 135
 136         /* Issue a FIFO read command in case we where idle. */
 137         if (stat->sreg.isr0 & SAB82532_ISR0_TIME) {
 138                 sunsab_cec_wait(up);
 139                 writeb(SAB82532_CMDR_RFRD, &up->regs->w.cmdr);
 140                 return tty;
 141         }
 142
 143         if (stat->sreg.isr0 & SAB82532_ISR0_RFO)
 144                 free_fifo++;
 145
 146         /* Read the FIFO. */
 147         for (i = 0; i < count; i++)
 148                 buf[i] = readb(&up->regs->r.rfifo[i]);
 149
 150         /* Issue Receive Message Complete command. */
 151         if (free_fifo) {
 152                 sunsab_cec_wait(up);
 153                 writeb(SAB82532_CMDR_RMC, &up->regs->w.cmdr);
 154         }
 155
 156         /* Count may be zero for BRK, so we check for it here */
 157         if ((stat->sreg.isr1 & SAB82532_ISR1_BRK) &&
 158             (up->port.line == up->port.cons->index))
 159                 saw_console_brk = 1;
 160
 161         for (i = 0; i < count; i++) {
 162                 unsigned char ch = buf[i];
 163
 164                 if (tty == NULL) {
 165                         uart_handle_sysrq_char(&up->port, ch, regs);
 166                         continue;
 167                 }
 168
 169                 if (unlikely(tty->flip.count >= TTY_FLIPBUF_SIZE)) {
 170                         tty->flip.work.func((void *)tty);
 171                         if (tty->flip.count >= TTY_FLIPBUF_SIZE)
 172                                 return tty; // if TTY_DONT_FLIP is set
 173                 }
 174
 175                 *tty->flip.char_buf_ptr = ch;
 176                 *tty->flip.flag_buf_ptr = TTY_NORMAL;
 177                 up->port.icount.rx++;
 178
 179                 if (unlikely(stat->sreg.isr0 & (SAB82532_ISR0_PERR |
 180                                                 SAB82532_ISR0_FERR |
 181                                                 SAB82532_ISR0_RFO)) ||
 182                     unlikely(stat->sreg.isr1 & SAB82532_ISR1_BRK)) {
 183                         /*
 184                          * For statistics only
 185                          */
 186                         if (stat->sreg.isr1 & SAB82532_ISR1_BRK) {
 187                                 stat->sreg.isr0 &= ~(SAB82532_ISR0_PERR |
 188                                                      SAB82532_ISR0_FERR);
 189                                 up->port.icount.brk++;
 190                                 /*
 191                                  * We do the SysRQ and SAK checking
 192                                  * here because otherwise the break
 193                                  * may get masked by ignore_status_mask
 194                                  * or read_status_mask.
 195                                  */
 196                                 if (uart_handle_break(&up->port))
 197                                         continue;
 198                         } else if (stat->sreg.isr0 & SAB82532_ISR0_PERR)
 199                                 up->port.icount.parity++;
 200                         else if (stat->sreg.isr0 & SAB82532_ISR0_FERR)
 201                                 up->port.icount.frame++;
 202                         if (stat->sreg.isr0 & SAB82532_ISR0_RFO)
 203                                 up->port.icount.overrun++;
 204
 205                         /*
 206                          * Mask off conditions which should be ingored.
 207                          */
 208                         stat->sreg.isr0 &= (up->port.read_status_mask & 0xff);
 209                         stat->sreg.isr1 &= ((up->port.read_status_mask >> 8) & 0xff);
 210
 211                         if (stat->sreg.isr1 & SAB82532_ISR1_BRK) {
 212                                 *tty->flip.flag_buf_ptr = TTY_BREAK;
 213                         } else if (stat->sreg.isr0 & SAB82532_ISR0_PERR)
 214                                 *tty->flip.flag_buf_ptr = TTY_PARITY;
 215                         else if (stat->sreg.isr0 & SAB82532_ISR0_FERR)
 216                                 *tty->flip.flag_buf_ptr = TTY_FRAME;
 217                 }
 218
 219                 if (uart_handle_sysrq_char(&up->port, ch, regs))
 220                         continue;
 221
 222                 if ((stat->sreg.isr0 & (up->port.ignore_status_mask & 0xff)) == 0 &&
 223                     (stat->sreg.isr1 & ((up->port.ignore_status_mask >> 8) & 0xff)) == 0){
 224                         tty->flip.flag_buf_ptr++;
 225                         tty->flip.char_buf_ptr++;
 226                         tty->flip.count++;
 227                 }
 228                 if ((stat->sreg.isr0 & SAB82532_ISR0_RFO) &&
 229                     tty->flip.count < TTY_FLIPBUF_SIZE) {
 230                         /*
 231                          * Overrun is special, since it's reported
 232                          * immediately, and doesn't affect the current
 233                          * character.
 234                          */
 235                         *tty->flip.flag_buf_ptr = TTY_OVERRUN;
 236                         tty->flip.flag_buf_ptr++;
 237                         tty->flip.char_buf_ptr++;
 238                         tty->flip.count++;
 239                 }
 240         }
 241
 242         if (saw_console_brk)
 243                 sun_do_break();
 244
 245         return tty;
 246 }
 247
 248 static void sunsab_stop_tx(struct uart_port *);
 249 static void sunsab_tx_idle(struct uart_sunsab_port *);
 250
 251 static void transmit_chars(struct uart_sunsab_port *up,
 252                            union sab82532_irq_status *stat)
 253 {
 254         struct circ_buf *xmit = &up->port.info->xmit;
 255         int i;
 256
 257         if (stat->sreg.isr1 & SAB82532_ISR1_ALLS) {
 258                 up->interrupt_mask1 |= SAB82532_IMR1_ALLS;
 259                 writeb(up->interrupt_mask1, &up->regs->w.imr1);
 260                 set_bit(SAB82532_ALLS, &up->irqflags);
 261         }
 262
 263 #if 0 /* bde@nwlink.com says this check causes problems */
 264         if (!(stat->sreg.isr1 & SAB82532_ISR1_XPR))
 265                 return;
 266 #endif
 267
 268         if (!(readb(&up->regs->r.star) & SAB82532_STAR_XFW))
 269                 return;
 270
 271         set_bit(SAB82532_XPR, &up->irqflags);
 272         sunsab_tx_idle(up);
 273
 274         if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
 275                 up->interrupt_mask1 |= SAB82532_IMR1_XPR;
 276                 writeb(up->interrupt_mask1, &up->regs->w.imr1);
 277                 return;
 278         }
 279
 280         up->interrupt_mask1 &= ~(SAB82532_IMR1_ALLS|SAB82532_IMR1_XPR);
 281         writeb(up->interrupt_mask1, &up->regs->w.imr1);
 282         clear_bit(SAB82532_ALLS, &up->irqflags);
 283
 284         /* Stuff 32 bytes into Transmit FIFO. */
 285         clear_bit(SAB82532_XPR, &up->irqflags);
 286         for (i = 0; i < up->port.fifosize; i++) {
 287                 writeb(xmit->buf[xmit->tail],
 288                        &up->regs->w.xfifo[i]);
 289                 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 290                 up->port.icount.tx++;
 291                 if (uart_circ_empty(xmit))
 292                         break;
 293         }
 294
 295         /* Issue a Transmit Frame command. */
 296         sunsab_cec_wait(up);
 297         writeb(SAB82532_CMDR_XF, &up->regs->w.cmdr);
 298
 299         if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 300                 uart_write_wakeup(&up->port);
 301
 302         if (uart_circ_empty(xmit))
 303                 sunsab_stop_tx(&up->port);
 304 }
 305
 306 static void check_status(struct uart_sunsab_port *up,
 307                          union sab82532_irq_status *stat)
 308 {
 309         if (stat->sreg.isr0 & SAB82532_ISR0_CDSC)
 310                 uart_handle_dcd_change(&up->port,
 311                                        !(readb(&up->regs->r.vstr) & SAB82532_VSTR_CD));
 312
 313         if (stat->sreg.isr1 & SAB82532_ISR1_CSC)
 314                 uart_handle_cts_change(&up->port,
 315                                        (readb(&up->regs->r.star) & SAB82532_STAR_CTS));
 316
 317         if ((readb(&up->regs->r.pvr) & up->pvr_dsr_bit) ^ up->dsr) {
 318                 up->dsr = (readb(&up->regs->r.pvr) & up->pvr_dsr_bit) ? 0 : 1;
 319                 up->port.icount.dsr++;
 320         }
 321
 322         wake_up_interruptible(&up->port.info->delta_msr_wait);
 323 }
 324
 325 static irqreturn_t sunsab_interrupt(int irq, void *dev_id, struct pt_regs *regs)
 326 {
 327         struct uart_sunsab_port *up = dev_id;
 328         struct tty_struct *tty;
 329         union sab82532_irq_status status;
 330         unsigned long flags;
 331
 332         spin_lock_irqsave(&up->port.lock, flags);
 333
 334         status.stat = 0;
 335         if (readb(&up->regs->r.gis) & SAB82532_GIS_ISA0)
 336                 status.sreg.isr0 = readb(&up->regs->r.isr0);
 337         if (readb(&up->regs->r.gis) & SAB82532_GIS_ISA1)
 338                 status.sreg.isr1 = readb(&up->regs->r.isr1);
 339
 340         tty = NULL;
 341         if (status.stat) {
 342                 if ((status.sreg.isr0 & (SAB82532_ISR0_TCD | SAB82532_ISR0_TIME |
 343                                          SAB82532_ISR0_RFO | SAB82532_ISR0_RPF)) ||
 344                     (status.sreg.isr1 & SAB82532_ISR1_BRK))
 345                         tty = receive_chars(up, &status, regs);
 346                 if ((status.sreg.isr0 & SAB82532_ISR0_CDSC) ||
 347                     (status.sreg.isr1 & SAB82532_ISR1_CSC))
 348                         check_status(up, &status);
 349                 if (status.sreg.isr1 & (SAB82532_ISR1_ALLS | SAB82532_ISR1_XPR))
 350                         transmit_chars(up, &status);
 351         }
 352
 353         spin_unlock(&up->port.lock);
 354
 355         if (tty)
 356                 tty_flip_buffer_push(tty);
 357
 358         up++;
 359
 360         spin_lock(&up->port.lock);
 361
 362         status.stat = 0;
 363         if (readb(&up->regs->r.gis) & SAB82532_GIS_ISB0)
 364                 status.sreg.isr0 = readb(&up->regs->r.isr0);
 365         if (readb(&up->regs->r.gis) & SAB82532_GIS_ISB1)
 366                 status.sreg.isr1 = readb(&up->regs->r.isr1);
 367
 368         tty = NULL;
 369         if (status.stat) {
 370                 if ((status.sreg.isr0 & (SAB82532_ISR0_TCD | SAB82532_ISR0_TIME |
 371                                          SAB82532_ISR0_RFO | SAB82532_ISR0_RPF)) ||
 372                     (status.sreg.isr1 & SAB82532_ISR1_BRK))
 373
 374                         tty = receive_chars(up, &status, regs);
 375                 if ((status.sreg.isr0 & SAB82532_ISR0_CDSC) ||
 376                     (status.sreg.isr1 & (SAB82532_ISR1_BRK | SAB82532_ISR1_CSC)))
 377                         check_status(up, &status);
 378                 if (status.sreg.isr1 & (SAB82532_ISR1_ALLS | SAB82532_ISR1_XPR))
 379                         transmit_chars(up, &status);
 380         }
 381
 382         spin_unlock_irqrestore(&up->port.lock, flags);
 383
 384         if (tty)
 385                 tty_flip_buffer_push(tty);
 386
 387         return IRQ_HANDLED;
 388 }
 389
 390 /* port->lock is not held.  */
 391 static unsigned int sunsab_tx_empty(struct uart_port *port)
 392 {
 393         struct uart_sunsab_port *up = (struct uart_sunsab_port *) port;
 394         int ret;
 395
 396         /* Do not need a lock for a state test like this.  */
 397         if (test_bit(SAB82532_ALLS, &up->irqflags))
 398                 ret = TIOCSER_TEMT;
 399         else
 400                 ret = 0;
 401
 402         return ret;
 403 }
 404
 405 /* port->lock held by caller.  */
 406 static void sunsab_set_mctrl(struct uart_port *port, unsigned int mctrl)
 407 {
 408         struct uart_sunsab_port *up = (struct uart_sunsab_port *) port;
 409
 410         if (mctrl & TIOCM_RTS) {
 411                 up->cached_mode &= ~SAB82532_MODE_FRTS;
 412                 up->cached_mode |= SAB82532_MODE_RTS;
 413         } else {
 414                 up->cached_mode |= (SAB82532_MODE_FRTS |
 415                                     SAB82532_MODE_RTS);
 416         }
 417         if (mctrl & TIOCM_DTR) {
 418                 up->cached_pvr &= ~(up->pvr_dtr_bit);
 419         } else {
 420                 up->cached_pvr |= up->pvr_dtr_bit;
 421         }
 422
 423         set_bit(SAB82532_REGS_PENDING, &up->irqflags);
 424         if (test_bit(SAB82532_XPR, &up->irqflags))
 425                 sunsab_tx_idle(up);
 426 }
 427
 428 /* port->lock is held by caller and interrupts are disabled.  */
 429 static unsigned int sunsab_get_mctrl(struct uart_port *port)
 430 {
 431         struct uart_sunsab_port *up = (struct uart_sunsab_port *) port;
 432         unsigned char val;
 433         unsigned int result;
 434
 435         result = 0;
 436
 437         val = readb(&up->regs->r.pvr);
 438         result |= (val & up->pvr_dsr_bit) ? 0 : TIOCM_DSR;
 439
 440         val = readb(&up->regs->r.vstr);
 441         result |= (val & SAB82532_VSTR_CD) ? 0 : TIOCM_CAR;
 442
 443         val = readb(&up->regs->r.star);
 444         result |= (val & SAB82532_STAR_CTS) ? TIOCM_CTS : 0;
 445
 446         return result;
 447 }
 448
 449 /* port->lock held by caller.  */
 450 static void sunsab_stop_tx(struct uart_port *port)
 451 {
 452         struct uart_sunsab_port *up = (struct uart_sunsab_port *) port;
 453
 454         up->interrupt_mask1 |= SAB82532_IMR1_XPR;
 455         writeb(up->interrupt_mask1, &up->regs->w.imr1);
 456 }
 457
 458 /* port->lock held by caller.  */
 459 static void sunsab_tx_idle(struct uart_sunsab_port *up)
 460 {
 461         if (test_bit(SAB82532_REGS_PENDING, &up->irqflags)) {
 462                 u8 tmp;
 463
 464                 clear_bit(SAB82532_REGS_PENDING, &up->irqflags);
 465                 writeb(up->cached_mode, &up->regs->rw.mode);
 466                 writeb(up->cached_pvr, &up->regs->rw.pvr);
 467                 writeb(up->cached_dafo, &up->regs->w.dafo);
 468
 469                 writeb(up->cached_ebrg & 0xff, &up->regs->w.bgr);
 470                 tmp = readb(&up->regs->rw.ccr2);
 471                 tmp &= ~0xc0;
 472                 tmp |= (up->cached_ebrg >> 2) & 0xc0;
 473                 writeb(tmp, &up->regs->rw.ccr2);
 474         }
 475 }
 476
 477 /* port->lock held by caller.  */
 478 static void sunsab_start_tx(struct uart_port *port)
 479 {
 480         struct uart_sunsab_port *up = (struct uart_sunsab_port *) port;
 481         struct circ_buf *xmit = &up->port.info->xmit;
 482         int i;
 483
 484         up->interrupt_mask1 &= ~(SAB82532_IMR1_ALLS|SAB82532_IMR1_XPR);
 485         writeb(up->interrupt_mask1, &up->regs->w.imr1);
 486
 487         if (!test_bit(SAB82532_XPR, &up->irqflags))
 488                 return;
 489
 490         clear_bit(SAB82532_ALLS, &up->irqflags);
 491         clear_bit(SAB82532_XPR, &up->irqflags);
 492
 493         for (i = 0; i < up->port.fifosize; i++) {
 494                 writeb(xmit->buf[xmit->tail],
 495                        &up->regs->w.xfifo[i]);
 496                 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 497                 up->port.icount.tx++;
 498                 if (uart_circ_empty(xmit))
 499                         break;
 500         }
 501
 502         /* Issue a Transmit Frame command.  */
 503         sunsab_cec_wait(up);
 504         writeb(SAB82532_CMDR_XF, &up->regs->w.cmdr);
 505 }
 506
 507 /* port->lock is not held.  */
 508 static void sunsab_send_xchar(struct uart_port *port, char ch)
 509 {
 510         struct uart_sunsab_port *up = (struct uart_sunsab_port *) port;
 511         unsigned long flags;
 512
 513         spin_lock_irqsave(&up->port.lock, flags);
 514
 515         sunsab_tec_wait(up);
 516         writeb(ch, &up->regs->w.tic);
 517
 518         spin_unlock_irqrestore(&up->port.lock, flags);
 519 }
 520
 521 /* port->lock held by caller.  */
 522 static void sunsab_stop_rx(struct uart_port *port)
 523 {
 524         struct uart_sunsab_port *up = (struct uart_sunsab_port *) port;
 525
 526         up->interrupt_mask0 |= SAB82532_ISR0_TCD;
 527         writeb(up->interrupt_mask1, &up->regs->w.imr0);
 528 }
 529
 530 /* port->lock held by caller.  */
 531 static void sunsab_enable_ms(struct uart_port *port)
 532 {
 533         /* For now we always receive these interrupts.  */
 534 }
 535
 536 /* port->lock is not held.  */
 537 static void sunsab_break_ctl(struct uart_port *port, int break_state)
 538 {
 539         struct uart_sunsab_port *up = (struct uart_sunsab_port *) port;
 540         unsigned long flags;
 541         unsigned char val;
 542
 543         spin_lock_irqsave(&up->port.lock, flags);
 544
 545         val = up->cached_dafo;
 546         if (break_state)
 547                 val |= SAB82532_DAFO_XBRK;
 548         else
 549                 val &= ~SAB82532_DAFO_XBRK;
 550         up->cached_dafo = val;
 551
 552         set_bit(SAB82532_REGS_PENDING, &up->irqflags);
 553         if (test_bit(SAB82532_XPR, &up->irqflags))
 554                 sunsab_tx_idle(up);
 555
 556         spin_unlock_irqrestore(&up->port.lock, flags);
 557 }
 558
 559 /* port->lock is not held.  */
 560 static int sunsab_startup(struct uart_port *port)
 561 {
 562         struct uart_sunsab_port *up = (struct uart_sunsab_port *) port;
 563         unsigned long flags;
 564         unsigned char tmp;
 565
 566         spin_lock_irqsave(&up->port.lock, flags);
 567
 568         /*
 569          * Wait for any commands or immediate characters
 570          */
 571         sunsab_cec_wait(up);
 572         sunsab_tec_wait(up);
 573
 574         /*
 575          * Clear the FIFO buffers.
 576          */
 577         writeb(SAB82532_CMDR_RRES, &up->regs->w.cmdr);
 578         sunsab_cec_wait(up);
 579         writeb(SAB82532_CMDR_XRES, &up->regs->w.cmdr);
 580
 581         /*
 582          * Clear the interrupt registers.
 583          */
 584         (void) readb(&up->regs->r.isr0);
 585         (void) readb(&up->regs->r.isr1);
 586
 587         /*
 588          * Now, initialize the UART
 589          */
 590         writeb(0, &up->regs->w.ccr0);                           /* power-down */
 591         writeb(SAB82532_CCR0_MCE | SAB82532_CCR0_SC_NRZ |
 592                SAB82532_CCR0_SM_ASYNC, &up->regs->w.ccr0);
 593         writeb(SAB82532_CCR1_ODS | SAB82532_CCR1_BCR | 7, &up->regs->w.ccr1);
 594         writeb(SAB82532_CCR2_BDF | SAB82532_CCR2_SSEL |
 595                SAB82532_CCR2_TOE, &up->regs->w.ccr2);
 596         writeb(0, &up->regs->w.ccr3);
 597         writeb(SAB82532_CCR4_MCK4 | SAB82532_CCR4_EBRG, &up->regs->w.ccr4);
 598         up->cached_mode = (SAB82532_MODE_RTS | SAB82532_MODE_FCTS |
 599                            SAB82532_MODE_RAC);
 600         writeb(up->cached_mode, &up->regs->w.mode);
 601         writeb(SAB82532_RFC_DPS|SAB82532_RFC_RFTH_32, &up->regs->w.rfc);
 602
 603         tmp = readb(&up->regs->rw.ccr0);
 604         tmp |= SAB82532_CCR0_PU;        /* power-up */
 605         writeb(tmp, &up->regs->rw.ccr0);
 606
 607         /*
 608          * Finally, enable interrupts
 609          */
 610         up->interrupt_mask0 = (SAB82532_IMR0_PERR | SAB82532_IMR0_FERR |
 611                                SAB82532_IMR0_PLLA);
 612         writeb(up->interrupt_mask0, &up->regs->w.imr0);
 613         up->interrupt_mask1 = (SAB82532_IMR1_BRKT | SAB82532_IMR1_ALLS |
 614                                SAB82532_IMR1_XOFF | SAB82532_IMR1_TIN |
 615                                SAB82532_IMR1_CSC | SAB82532_IMR1_XON |
 616                                SAB82532_IMR1_XPR);
 617         writeb(up->interrupt_mask1, &up->regs->w.imr1);
 618         set_bit(SAB82532_ALLS, &up->irqflags);
 619         set_bit(SAB82532_XPR, &up->irqflags);
 620
 621         spin_unlock_irqrestore(&up->port.lock, flags);
 622
 623         return 0;
 624 }
 625
 626 /* port->lock is not held.  */
 627 static void sunsab_shutdown(struct uart_port *port)
 628 {
 629         struct uart_sunsab_port *up = (struct uart_sunsab_port *) port;
 630         unsigned long flags;
 631
 632         spin_lock_irqsave(&up->port.lock, flags);
 633
 634         /* Disable Interrupts */
 635         up->interrupt_mask0 = 0xff;
 636         writeb(up->interrupt_mask0, &up->regs->w.imr0);
 637         up->interrupt_mask1 = 0xff;
 638         writeb(up->interrupt_mask1, &up->regs->w.imr1);
 639
 640         /* Disable break condition */
 641         up->cached_dafo = readb(&up->regs->rw.dafo);
 642         up->cached_dafo &= ~SAB82532_DAFO_XBRK;
 643         writeb(up->cached_dafo, &up->regs->rw.dafo);
 644
 645         /* Disable Receiver */
 646         up->cached_mode &= ~SAB82532_MODE_RAC;
 647         writeb(up->cached_mode, &up->regs->rw.mode);
 648
 649         /*
 650          * XXX FIXME
 651          *
 652          * If the chip is powered down here the system hangs/crashes during
 653          * reboot or shutdown.  This needs to be investigated further,
 654          * similar behaviour occurs in 2.4 when the driver is configured
 655          * as a module only.  One hint may be that data is sometimes
 656          * transmitted at 9600 baud during shutdown (regardless of the
 657          * speed the chip was configured for when the port was open).
 658          */
 659 #if 0
 660         /* Power Down */
 661         tmp = readb(&up->regs->rw.ccr0);
 662         tmp &= ~SAB82532_CCR0_PU;
 663         writeb(tmp, &up->regs->rw.ccr0);
 664 #endif
 665
 666         spin_unlock_irqrestore(&up->port.lock, flags);
 667 }
 668
 669 /*
 670  * This is used to figure out the divisor speeds.
 671  *
 672  * The formula is:    Baud = SAB_BASE_BAUD / ((N + 1) * (1 << M)),
 673  *
 674  * with               0 <= N < 64 and 0 <= M < 16
 675  */
 676
 677 static void calc_ebrg(int baud, int *n_ret, int *m_ret)
 678 {
 679         int     n, m;
 680
 681         if (baud == 0) {
 682                 *n_ret = 0;
 683                 *m_ret = 0;
 684                 return;
 685         }
 686
 687         /*
 688          * We scale numbers by 10 so that we get better accuracy
 689          * without having to use floating point.  Here we increment m
 690          * until n is within the valid range.
 691          */
 692         n = (SAB_BASE_BAUD * 10) / baud;
 693         m = 0;
 694         while (n >= 640) {
 695                 n = n / 2;
 696                 m++;
 697         }
 698         n = (n+5) / 10;
 699         /*
 700          * We try very hard to avoid speeds with M == 0 since they may
 701          * not work correctly for XTAL frequences above 10 MHz.
 702          */
 703         if ((m == 0) && ((n & 1) == 0)) {
 704                 n = n / 2;
 705                 m++;
 706         }
 707         *n_ret = n - 1;
 708         *m_ret = m;
 709 }
 710
 711 /* Internal routine, port->lock is held and local interrupts are disabled.  */
 712 static void sunsab_convert_to_sab(struct uart_sunsab_port *up, unsigned int cflag,
 713                                   unsigned int iflag, unsigned int baud,
 714                                   unsigned int quot)
 715 {
 716         unsigned char dafo;
 717         int bits, n, m;
 718
 719         /* Byte size and parity */
 720         switch (cflag & CSIZE) {
 721               case CS5: dafo = SAB82532_DAFO_CHL5; bits = 7; break;
 722               case CS6: dafo = SAB82532_DAFO_CHL6; bits = 8; break;
 723               case CS7: dafo = SAB82532_DAFO_CHL7; bits = 9; break;
 724               case CS8: dafo = SAB82532_DAFO_CHL8; bits = 10; break;
 725               /* Never happens, but GCC is too dumb to figure it out */
 726               default:  dafo = SAB82532_DAFO_CHL5; bits = 7; break;
 727         }
 728
 729         if (cflag & CSTOPB) {
 730                 dafo |= SAB82532_DAFO_STOP;
 731                 bits++;
 732         }
 733
 734         if (cflag & PARENB) {
 735                 dafo |= SAB82532_DAFO_PARE;
 736                 bits++;
 737         }
 738
 739         if (cflag & PARODD) {
 740                 dafo |= SAB82532_DAFO_PAR_ODD;
 741         } else {
 742                 dafo |= SAB82532_DAFO_PAR_EVEN;
 743         }
 744         up->cached_dafo = dafo;
 745
 746         calc_ebrg(baud, &n, &m);
 747
 748         up->cached_ebrg = n | (m << 6);
 749
 750         up->tec_timeout = (10 * 1000000) / baud;
 751         up->cec_timeout = up->tec_timeout >> 2;
 752
 753         /* CTS flow control flags */
 754         /* We encode read_status_mask and ignore_status_mask like so:
 755          *
 756          * ---------------------
 757          * | ... | ISR1 | ISR0 |
 758          * ---------------------
 759          *  ..    15   8 7    0
 760          */
 761
 762         up->port.read_status_mask = (SAB82532_ISR0_TCD | SAB82532_ISR0_TIME |
 763                                      SAB82532_ISR0_RFO | SAB82532_ISR0_RPF |
 764                                      SAB82532_ISR0_CDSC);
 765         up->port.read_status_mask |= (SAB82532_ISR1_CSC |
 766                                       SAB82532_ISR1_ALLS |
 767                                       SAB82532_ISR1_XPR) << 8;
 768         if (iflag & INPCK)
 769                 up->port.read_status_mask |= (SAB82532_ISR0_PERR |
 770                                               SAB82532_ISR0_FERR);
 771         if (iflag & (BRKINT | PARMRK))
 772                 up->port.read_status_mask |= (SAB82532_ISR1_BRK << 8);
 773
 774         /*
 775          * Characteres to ignore
 776          */
 777         up->port.ignore_status_mask = 0;
 778         if (iflag & IGNPAR)
 779                 up->port.ignore_status_mask |= (SAB82532_ISR0_PERR |
 780                                                 SAB82532_ISR0_FERR);
 781         if (iflag & IGNBRK) {
 782                 up->port.ignore_status_mask |= (SAB82532_ISR1_BRK << 8);
 783                 /*
 784                  * If we're ignoring parity and break indicators,
 785                  * ignore overruns too (for real raw support).
 786                  */
 787                 if (iflag & IGNPAR)
 788                         up->port.ignore_status_mask |= SAB82532_ISR0_RFO;
 789         }
 790
 791         /*
 792          * ignore all characters if CREAD is not set
 793          */
 794         if ((cflag & CREAD) == 0)
 795                 up->port.ignore_status_mask |= (SAB82532_ISR0_RPF |
 796                                                 SAB82532_ISR0_TCD);
 797
 798         uart_update_timeout(&up->port, cflag,
 799                             (up->port.uartclk / (16 * quot)));
 800
 801         /* Now schedule a register update when the chip's
 802          * transmitter is idle.
 803          */
 804         up->cached_mode |= SAB82532_MODE_RAC;
 805         set_bit(SAB82532_REGS_PENDING, &up->irqflags);
 806         if (test_bit(SAB82532_XPR, &up->irqflags))
 807                 sunsab_tx_idle(up);
 808 }
 809
 810 /* port->lock is not held.  */
 811 static void sunsab_set_termios(struct uart_port *port, struct termios *termios,
 812                                struct termios *old)
 813 {
 814         struct uart_sunsab_port *up = (struct uart_sunsab_port *) port;
 815         unsigned long flags;
 816         unsigned int baud = uart_get_baud_rate(port, termios, old, 0, 4000000);
 817         unsigned int quot = uart_get_divisor(port, baud);
 818
 819         spin_lock_irqsave(&up->port.lock, flags);
 820         sunsab_convert_to_sab(up, termios->c_cflag, termios->c_iflag, baud, quot);
 821         spin_unlock_irqrestore(&up->port.lock, flags);
 822 }
 823
 824 static const char *sunsab_type(struct uart_port *port)
 825 {
 826         struct uart_sunsab_port *up = (void *)port;
 827         static char buf[36];
 828
 829         sprintf(buf, "SAB82532 %s", sab82532_version[up->type]);
 830         return buf;
 831 }
 832
 833 static void sunsab_release_port(struct uart_port *port)
 834 {
 835 }
 836
 837 static int sunsab_request_port(struct uart_port *port)
 838 {
 839         return 0;
 840 }
 841
 842 static void sunsab_config_port(struct uart_port *port, int flags)
 843 {
 844 }
 845
 846 static int sunsab_verify_port(struct uart_port *port, struct serial_struct *ser)
 847 {
 848         return -EINVAL;
 849 }
 850
 851 static struct uart_ops sunsab_pops = {
 852         .tx_empty       = sunsab_tx_empty,
 853         .set_mctrl      = sunsab_set_mctrl,
 854         .get_mctrl      = sunsab_get_mctrl,
 855         .stop_tx        = sunsab_stop_tx,
 856         .start_tx       = sunsab_start_tx,
 857         .send_xchar     = sunsab_send_xchar,
 858         .stop_rx        = sunsab_stop_rx,
 859         .enable_ms      = sunsab_enable_ms,
 860         .break_ctl      = sunsab_break_ctl,
 861         .startup        = sunsab_startup,
 862         .shutdown       = sunsab_shutdown,
 863         .set_termios    = sunsab_set_termios,
 864         .type           = sunsab_type,
 865         .release_port   = sunsab_release_port,
 866         .request_port   = sunsab_request_port,
 867         .config_port    = sunsab_config_port,
 868         .verify_port    = sunsab_verify_port,
 869 };
 870
 871 static struct uart_driver sunsab_reg = {
 872         .owner                  = THIS_MODULE,
 873         .driver_name            = "serial",
 874         .devfs_name             = "tts/",
 875         .dev_name               = "ttyS",
 876         .major                  = TTY_MAJOR,
 877 };
 878
 879 static struct uart_sunsab_port *sunsab_ports;
 880 static int num_channels;
 881
 882 #ifdef CONFIG_SERIAL_SUNSAB_CONSOLE
 883
 884 static __inline__ void sunsab_console_putchar(struct uart_sunsab_port *up, char c)
 885 {
 886         unsigned long flags;
 887
 888         spin_lock_irqsave(&up->port.lock, flags);
 889
 890         sunsab_tec_wait(up);
 891         writeb(c, &up->regs->w.tic);
 892
 893         spin_unlock_irqrestore(&up->port.lock, flags);
 894 }
 895
 896 static void sunsab_console_write(struct console *con, const char *s, unsigned n)
 897 {
 898         struct uart_sunsab_port *up = &sunsab_ports[con->index];
 899         int i;
 900
 901         for (i = 0; i < n; i++) {
 902                 if (*s == '\n')
 903                         sunsab_console_putchar(up, '\r');
 904                 sunsab_console_putchar(up, *s++);
 905         }
 906         sunsab_tec_wait(up);
 907 }
 908
 909 static int sunsab_console_setup(struct console *con, char *options)
 910 {
 911         struct uart_sunsab_port *up = &sunsab_ports[con->index];
 912         unsigned long flags;
 913         unsigned int baud, quot;
 914
 915         printk("Console: ttyS%d (SAB82532)\n",
 916                (sunsab_reg.minor - 64) + con->index);
 917
 918         sunserial_console_termios(con);
 919
 920         /* Firmware console speed is limited to 150-->38400 baud so
 921          * this hackish cflag thing is OK.
 922          */
 923         switch (con->cflag & CBAUD) {
 924         case B150: baud = 150; break;
 925         case B300: baud = 300; break;
 926         case B600: baud = 600; break;
 927         case B1200: baud = 1200; break;
 928         case B2400: baud = 2400; break;
 929         case B4800: baud = 4800; break;
 930         default: case B9600: baud = 9600; break;
 931         case B19200: baud = 19200; break;
 932         case B38400: baud = 38400; break;
 933         };
 934
 935         /*
 936          * Temporary fix.
 937          */
 938         spin_lock_init(&up->port.lock);
 939
 940         /*
 941          * Initialize the hardware
 942          */
 943         sunsab_startup(&up->port);
 944
 945         spin_lock_irqsave(&up->port.lock, flags);
 946
 947         /*
 948          * Finally, enable interrupts
 949          */
 950         up->interrupt_mask0 = SAB82532_IMR0_PERR | SAB82532_IMR0_FERR |
 951                                 SAB82532_IMR0_PLLA | SAB82532_IMR0_CDSC;
 952         writeb(up->interrupt_mask0, &up->regs->w.imr0);
 953         up->interrupt_mask1 = SAB82532_IMR1_BRKT | SAB82532_IMR1_ALLS |
 954                                 SAB82532_IMR1_XOFF | SAB82532_IMR1_TIN |
 955                                 SAB82532_IMR1_CSC | SAB82532_IMR1_XON |
 956                                 SAB82532_IMR1_XPR;
 957         writeb(up->interrupt_mask1, &up->regs->w.imr1);
 958
 959         quot = uart_get_divisor(&up->port, baud);
 960         sunsab_convert_to_sab(up, con->cflag, 0, baud, quot);
 961         sunsab_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS);
 962
 963         spin_unlock_irqrestore(&up->port.lock, flags);
 964
 965         return 0;
 966 }
 967
 968 static struct console sunsab_console = {
 969         .name   =       "ttyS",
 970         .write  =       sunsab_console_write,
 971         .device =       uart_console_device,
 972         .setup  =       sunsab_console_setup,
 973         .flags  =       CON_PRINTBUFFER,
 974         .index  =       -1,
 975         .data   =       &sunsab_reg,
 976 };
 977 #define SUNSAB_CONSOLE  (&sunsab_console)
 978
 979 static void __init sunsab_console_init(void)
 980 {
 981         int i;
 982
 983         if (con_is_present())
 984                 return;
 985
 986         for (i = 0; i < num_channels; i++) {
 987                 int this_minor = sunsab_reg.minor + i;
 988
 989                 if ((this_minor - 64) == (serial_console - 1))
 990                         break;
 991         }
 992         if (i == num_channels)
 993                 return;
 994
 995         sunsab_console.index = i;
 996         register_console(&sunsab_console);
 997 }
 998 #else
 999 #define SUNSAB_CONSOLE          (NULL)
1000 #define sunsab_console_init()   do { } while (0)
1001 #endif
1002
1003 static void __init for_each_sab_edev(void (*callback)(struct linux_ebus_device *, void *), void *arg)
1004 {
1005         struct linux_ebus *ebus;
1006         struct linux_ebus_device *edev = NULL;
1007
1008         for_each_ebus(ebus) {
1009                 for_each_ebusdev(edev, ebus) {
1010                         if (!strcmp(edev->prom_name, "se")) {
1011                                 callback(edev, arg);
1012                                 continue;
1013                         } else if (!strcmp(edev->prom_name, "serial")) {
1014                                 char compat[32];
1015                                 int clen;
1016
1017                                 /* On RIO this can be an SE, check it.  We could
1018                                  * just check ebus->is_rio, but this is more portable.
1019                                  */
1020                                 clen = prom_getproperty(edev->prom_node, "compatible",
1021                                                         compat, sizeof(compat));
1022                                 if (clen > 0) {
1023                                         if (strncmp(compat, "sab82532", 8) == 0) {
1024                                                 callback(edev, arg);
1025                                                 continue;
1026                                         }
1027                                 }
1028                         }
1029                 }
1030         }
1031 }
1032
1033 static void __init sab_count_callback(struct linux_ebus_device *edev, void *arg)
1034 {
1035         int *count_p = arg;
1036
1037         (*count_p)++;
1038 }
1039
1040 static void __init sab_attach_callback(struct linux_ebus_device *edev, void *arg)
1041 {
1042         int *instance_p = arg;
1043         struct uart_sunsab_port *up;
1044         unsigned long regs, offset;
1045         int i;
1046
1047         /* Note: ports are located in reverse order */
1048         regs = edev->resource[0].start;
1049         offset = sizeof(union sab82532_async_regs);
1050         for (i = 0; i < 2; i++) {
1051                 up = &sunsab_ports[(*instance_p * 2) + 1 - i];
1052
1053                 memset(up, 0, sizeof(*up));
1054                 up->regs = ioremap(regs + offset, sizeof(union sab82532_async_regs));
1055                 up->port.irq = edev->irqs[0];
1056                 up->port.fifosize = SAB82532_XMIT_FIFO_SIZE;
1057                 up->port.mapbase = (unsigned long)up->regs;
1058                 up->port.iotype = SERIAL_IO_MEM;
1059
1060                 writeb(SAB82532_IPC_IC_ACT_LOW, &up->regs->w.ipc);
1061
1062                 offset -= sizeof(union sab82532_async_regs);
1063         }
1064
1065         (*instance_p)++;
1066 }
1067
1068 static int __init probe_for_sabs(void)
1069 {
1070         int this_sab = 0;
1071
1072         /* Find device instances.  */
1073         for_each_sab_edev(&sab_count_callback, &this_sab);
1074         if (!this_sab)
1075                 return -ENODEV;
1076
1077         /* Allocate tables.  */
1078         sunsab_ports = kmalloc(sizeof(struct uart_sunsab_port) * this_sab * 2,
1079                                GFP_KERNEL);
1080         if (!sunsab_ports)
1081                 return -ENOMEM;
1082
1083         num_channels = this_sab * 2;
1084
1085         this_sab = 0;
1086         for_each_sab_edev(&sab_attach_callback, &this_sab);
1087         return 0;
1088 }
1089
1090 static void __init sunsab_init_hw(void)
1091 {
1092         int i;
1093
1094         for (i = 0; i < num_channels; i++) {
1095                 struct uart_sunsab_port *up = &sunsab_ports[i];
1096
1097                 up->port.line = i;
1098                 up->port.ops = &sunsab_pops;
1099                 up->port.type = PORT_SUNSAB;
1100                 up->port.uartclk = SAB_BASE_BAUD;
1101
1102                 up->type = readb(&up->regs->r.vstr) & 0x0f;
1103                 writeb(~((1 << 1) | (1 << 2) | (1 << 4)), &up->regs->w.pcr);
1104                 writeb(0xff, &up->regs->w.pim);
1105                 if (up->port.line == 0) {
1106                         up->pvr_dsr_bit = (1 << 0);
1107                         up->pvr_dtr_bit = (1 << 1);
1108                 } else {
1109                         up->pvr_dsr_bit = (1 << 3);
1110                         up->pvr_dtr_bit = (1 << 2);
1111                 }
1112                 up->cached_pvr = (1 << 1) | (1 << 2) | (1 << 4);
1113                 writeb(up->cached_pvr, &up->regs->w.pvr);
1114                 up->cached_mode = readb(&up->regs->rw.mode);
1115                 up->cached_mode |= SAB82532_MODE_FRTS;
1116                 writeb(up->cached_mode, &up->regs->rw.mode);
1117                 up->cached_mode |= SAB82532_MODE_RTS;
1118                 writeb(up->cached_mode, &up->regs->rw.mode);
1119
1120                 up->tec_timeout = SAB82532_MAX_TEC_TIMEOUT;
1121                 up->cec_timeout = SAB82532_MAX_CEC_TIMEOUT;
1122
1123                 if (!(up->port.line & 0x01)) {
1124                         if (request_irq(up->port.irq, sunsab_interrupt,
1125                                         SA_SHIRQ, "serial(sab82532)", up)) {
1126                                 printk("sunsab%d: can't get IRQ %x\n",
1127                                        i, up->port.irq);
1128                                 continue;
1129                         }
1130                 }
1131         }
1132 }
1133
1134 static int __init sunsab_init(void)
1135 {
1136         int ret = probe_for_sabs();
1137         int i;
1138
1139         if (ret < 0)
1140                 return ret;
1141
1142         sunsab_init_hw();
1143
1144         sunsab_reg.minor = sunserial_current_minor;
1145         sunsab_reg.nr = num_channels;
1146         sunsab_reg.cons = SUNSAB_CONSOLE;
1147
1148         ret = uart_register_driver(&sunsab_reg);
1149         if (ret < 0) {
1150                 int i;
1151
1152                 for (i = 0; i < num_channels; i++) {
1153                         struct uart_sunsab_port *up = &sunsab_ports[i];
1154
1155                         if (!(up->port.line & 0x01))
1156                                 free_irq(up->port.irq, up);
1157                         iounmap(up->regs);
1158                 }
1159                 kfree(sunsab_ports);
1160                 sunsab_ports = NULL;
1161
1162                 return ret;
1163         }
1164
1165         sunserial_current_minor += num_channels;
1166
1167         sunsab_console_init();
1168
1169         for (i = 0; i < num_channels; i++) {
1170                 struct uart_sunsab_port *up = &sunsab_ports[i];
1171
1172                 uart_add_one_port(&sunsab_reg, &up->port);
1173         }
1174
1175         return 0;
1176 }
1177
1178 static void __exit sunsab_exit(void)
1179 {
1180         int i;
1181
1182         for (i = 0; i < num_channels; i++) {
1183                 struct uart_sunsab_port *up = &sunsab_ports[i];
1184
1185                 uart_remove_one_port(&sunsab_reg, &up->port);
1186
1187                 if (!(up->port.line & 0x01))
1188                         free_irq(up->port.irq, up);
1189                 iounmap(up->regs);
1190         }
1191
1192         sunserial_current_minor -= num_channels;
1193         uart_unregister_driver(&sunsab_reg);
1194
1195         kfree(sunsab_ports);
1196         sunsab_ports = NULL;
1197 }
1198
1199 module_init(sunsab_init);
1200 module_exit(sunsab_exit);
1201
1202 MODULE_AUTHOR("Eddie C. Dost and David S. Miller");
1203 MODULE_DESCRIPTION("Sun SAB82532 serial port driver");
1204 MODULE_LICENSE("GPL");