drivers/rtc/rtc-ds1305.c

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * rtc-ds1305.c -- driver for DS1305 and DS1306 SPI RTC chips
   4  *
   5  * Copyright (C) 2008 David Brownell
   6  */
   7 #include <linux/kernel.h>
   8 #include <linux/init.h>
   9 #include <linux/bcd.h>
  10 #include <linux/slab.h>
  11 #include <linux/rtc.h>
  12 #include <linux/workqueue.h>
  13
  14 #include <linux/spi/spi.h>
  15 #include <linux/spi/ds1305.h>
  16 #include <linux/module.h>
  17
  18
  19 /*
  20  * Registers ... mask DS1305_WRITE into register address to write,
  21  * otherwise you're reading it.  All non-bitmask values are BCD.
  22  */
  23 #define DS1305_WRITE            0x80
  24
  25
  26 /* RTC date/time ... the main special cases are that we:
  27  *  - Need fancy "hours" encoding in 12hour mode
  28  *  - Don't rely on the "day-of-week" field (or tm_wday)
  29  *  - Are a 21st-century clock (2000 <= year < 2100)
  30  */
  31 #define DS1305_RTC_LEN          7               /* bytes for RTC regs */
  32
  33 #define DS1305_SEC              0x00            /* register addresses */
  34 #define DS1305_MIN              0x01
  35 #define DS1305_HOUR             0x02
  36 #       define DS1305_HR_12             0x40    /* set == 12 hr mode */
  37 #       define DS1305_HR_PM             0x20    /* set == PM (12hr mode) */
  38 #define DS1305_WDAY             0x03
  39 #define DS1305_MDAY             0x04
  40 #define DS1305_MON              0x05
  41 #define DS1305_YEAR             0x06
  42
  43
  44 /* The two alarms have only sec/min/hour/wday fields (ALM_LEN).
  45  * DS1305_ALM_DISABLE disables a match field (some combos are bad).
  46  *
  47  * NOTE that since we don't use WDAY, we limit ourselves to alarms
  48  * only one day into the future (vs potentially up to a week).
  49  *
  50  * NOTE ALSO that while we could generate once-a-second IRQs (UIE), we
  51  * don't currently support them.  We'd either need to do it only when
  52  * no alarm is pending (not the standard model), or to use the second
  53  * alarm (implying that this is a DS1305 not DS1306, *and* that either
  54  * it's wired up a second IRQ we know, or that INTCN is set)
  55  */
  56 #define DS1305_ALM_LEN          4               /* bytes for ALM regs */
  57 #define DS1305_ALM_DISABLE      0x80
  58
  59 #define DS1305_ALM0(r)          (0x07 + (r))    /* register addresses */
  60 #define DS1305_ALM1(r)          (0x0b + (r))
  61
  62
  63 /* three control registers */
  64 #define DS1305_CONTROL_LEN      3               /* bytes of control regs */
  65
  66 #define DS1305_CONTROL          0x0f            /* register addresses */
  67 #       define DS1305_nEOSC             0x80    /* low enables oscillator */
  68 #       define DS1305_WP                0x40    /* write protect */
  69 #       define DS1305_INTCN             0x04    /* clear == only int0 used */
  70 #       define DS1306_1HZ               0x04    /* enable 1Hz output */
  71 #       define DS1305_AEI1              0x02    /* enable ALM1 IRQ */
  72 #       define DS1305_AEI0              0x01    /* enable ALM0 IRQ */
  73 #define DS1305_STATUS           0x10
  74 /* status has just AEIx bits, mirrored as IRQFx */
  75 #define DS1305_TRICKLE          0x11
  76 /* trickle bits are defined in <linux/spi/ds1305.h> */
  77
  78 /* a bunch of NVRAM */
  79 #define DS1305_NVRAM_LEN        96              /* bytes of NVRAM */
  80
  81 #define DS1305_NVRAM            0x20            /* register addresses */
  82
  83
  84 struct ds1305 {
  85         struct spi_device       *spi;
  86         struct rtc_device       *rtc;
  87
  88         struct work_struct      work;
  89
  90         unsigned long           flags;
  91 #define FLAG_EXITING    0
  92
  93         bool                    hr12;
  94         u8                      ctrl[DS1305_CONTROL_LEN];
  95 };
  96
  97
  98 /*----------------------------------------------------------------------*/
  99
 100 /*
 101  * Utilities ...  tolerate 12-hour AM/PM notation in case of non-Linux
 102  * software (like a bootloader) which may require it.
 103  */
 104
 105 static unsigned bcd2hour(u8 bcd)
 106 {
 107         if (bcd & DS1305_HR_12) {
 108                 unsigned        hour = 0;
 109
 110                 bcd &= ~DS1305_HR_12;
 111                 if (bcd & DS1305_HR_PM) {
 112                         hour = 12;
 113                         bcd &= ~DS1305_HR_PM;
 114                 }
 115                 hour += bcd2bin(bcd);
 116                 return hour - 1;
 117         }
 118         return bcd2bin(bcd);
 119 }
 120
 121 static u8 hour2bcd(bool hr12, int hour)
 122 {
 123         if (hr12) {
 124                 hour++;
 125                 if (hour <= 12)
 126                         return DS1305_HR_12 | bin2bcd(hour);
 127                 hour -= 12;
 128                 return DS1305_HR_12 | DS1305_HR_PM | bin2bcd(hour);
 129         }
 130         return bin2bcd(hour);
 131 }
 132
 133 /*----------------------------------------------------------------------*/
 134
 135 /*
 136  * Interface to RTC framework
 137  */
 138
 139 static int ds1305_alarm_irq_enable(struct device *dev, unsigned int enabled)
 140 {
 141         struct ds1305   *ds1305 = dev_get_drvdata(dev);
 142         u8              buf[2];
 143         long            err = -EINVAL;
 144
 145         buf[0] = DS1305_WRITE | DS1305_CONTROL;
 146         buf[1] = ds1305->ctrl[0];
 147
 148         if (enabled) {
 149                 if (ds1305->ctrl[0] & DS1305_AEI0)
 150                         goto done;
 151                 buf[1] |= DS1305_AEI0;
 152         } else {
 153                 if (!(buf[1] & DS1305_AEI0))
 154                         goto done;
 155                 buf[1] &= ~DS1305_AEI0;
 156         }
 157         err = spi_write_then_read(ds1305->spi, buf, sizeof(buf), NULL, 0);
 158         if (err >= 0)
 159                 ds1305->ctrl[0] = buf[1];
 160 done:
 161         return err;
 162
 163 }
 164
 165
 166 /*
 167  * Get/set of date and time is pretty normal.
 168  */
 169
 170 static int ds1305_get_time(struct device *dev, struct rtc_time *time)
 171 {
 172         struct ds1305   *ds1305 = dev_get_drvdata(dev);
 173         u8              addr = DS1305_SEC;
 174         u8              buf[DS1305_RTC_LEN];
 175         int             status;
 176
 177         /* Use write-then-read to get all the date/time registers
 178          * since dma from stack is nonportable
 179          */
 180         status = spi_write_then_read(ds1305->spi, &addr, sizeof(addr),
 181                         buf, sizeof(buf));
 182         if (status < 0)
 183                 return status;
 184
 185         dev_vdbg(dev, "%s: %3ph, %4ph\n", "read", &buf[0], &buf[3]);
 186
 187         /* Decode the registers */
 188         time->tm_sec = bcd2bin(buf[DS1305_SEC]);
 189         time->tm_min = bcd2bin(buf[DS1305_MIN]);
 190         time->tm_hour = bcd2hour(buf[DS1305_HOUR]);
 191         time->tm_wday = buf[DS1305_WDAY] - 1;
 192         time->tm_mday = bcd2bin(buf[DS1305_MDAY]);
 193         time->tm_mon = bcd2bin(buf[DS1305_MON]) - 1;
 194         time->tm_year = bcd2bin(buf[DS1305_YEAR]) + 100;
 195
 196         dev_vdbg(dev, "%s secs=%d, mins=%d, "
 197                 "hours=%d, mday=%d, mon=%d, year=%d, wday=%d\n",
 198                 "read", time->tm_sec, time->tm_min,
 199                 time->tm_hour, time->tm_mday,
 200                 time->tm_mon, time->tm_year, time->tm_wday);
 201
 202         return 0;
 203 }
 204
 205 static int ds1305_set_time(struct device *dev, struct rtc_time *time)
 206 {
 207         struct ds1305   *ds1305 = dev_get_drvdata(dev);
 208         u8              buf[1 + DS1305_RTC_LEN];
 209         u8              *bp = buf;
 210
 211         dev_vdbg(dev, "%s secs=%d, mins=%d, "
 212                 "hours=%d, mday=%d, mon=%d, year=%d, wday=%d\n",
 213                 "write", time->tm_sec, time->tm_min,
 214                 time->tm_hour, time->tm_mday,
 215                 time->tm_mon, time->tm_year, time->tm_wday);
 216
 217         /* Write registers starting at the first time/date address. */
 218         *bp++ = DS1305_WRITE | DS1305_SEC;
 219
 220         *bp++ = bin2bcd(time->tm_sec);
 221         *bp++ = bin2bcd(time->tm_min);
 222         *bp++ = hour2bcd(ds1305->hr12, time->tm_hour);
 223         *bp++ = (time->tm_wday < 7) ? (time->tm_wday + 1) : 1;
 224         *bp++ = bin2bcd(time->tm_mday);
 225         *bp++ = bin2bcd(time->tm_mon + 1);
 226         *bp++ = bin2bcd(time->tm_year - 100);
 227
 228         dev_dbg(dev, "%s: %3ph, %4ph\n", "write", &buf[1], &buf[4]);
 229
 230         /* use write-then-read since dma from stack is nonportable */
 231         return spi_write_then_read(ds1305->spi, buf, sizeof(buf),
 232                         NULL, 0);
 233 }
 234
 235 /*
 236  * Get/set of alarm is a bit funky:
 237  *
 238  * - First there's the inherent raciness of getting the (partitioned)
 239  *   status of an alarm that could trigger while we're reading parts
 240  *   of that status.
 241  *
 242  * - Second there's its limited range (we could increase it a bit by
 243  *   relying on WDAY), which means it will easily roll over.
 244  *
 245  * - Third there's the choice of two alarms and alarm signals.
 246  *   Here we use ALM0 and expect that nINT0 (open drain) is used;
 247  *   that's the only real option for DS1306 runtime alarms, and is
 248  *   natural on DS1305.
 249  *
 250  * - Fourth, there's also ALM1, and a second interrupt signal:
 251  *     + On DS1305 ALM1 uses nINT1 (when INTCN=1) else nINT0;
 252  *     + On DS1306 ALM1 only uses INT1 (an active high pulse)
 253  *       and it won't work when VCC1 is active.
 254  *
 255  *   So to be most general, we should probably set both alarms to the
 256  *   same value, letting ALM1 be the wakeup event source on DS1306
 257  *   and handling several wiring options on DS1305.
 258  *
 259  * - Fifth, we support the polled mode (as well as possible; why not?)
 260  *   even when no interrupt line is wired to an IRQ.
 261  */
 262
 263 /*
 264  * Context: caller holds rtc->ops_lock (to protect ds1305->ctrl)
 265  */
 266 static int ds1305_get_alarm(struct device *dev, struct rtc_wkalrm *alm)
 267 {
 268         struct ds1305   *ds1305 = dev_get_drvdata(dev);
 269         struct spi_device *spi = ds1305->spi;
 270         u8              addr;
 271         int             status;
 272         u8              buf[DS1305_ALM_LEN];
 273
 274         /* Refresh control register cache BEFORE reading ALM0 registers,
 275          * since reading alarm registers acks any pending IRQ.  That
 276          * makes returning "pending" status a bit of a lie, but that bit
 277          * of EFI status is at best fragile anyway (given IRQ handlers).
 278          */
 279         addr = DS1305_CONTROL;
 280         status = spi_write_then_read(spi, &addr, sizeof(addr),
 281                         ds1305->ctrl, sizeof(ds1305->ctrl));
 282         if (status < 0)
 283                 return status;
 284
 285         alm->enabled = !!(ds1305->ctrl[0] & DS1305_AEI0);
 286         alm->pending = !!(ds1305->ctrl[1] & DS1305_AEI0);
 287
 288         /* get and check ALM0 registers */
 289         addr = DS1305_ALM0(DS1305_SEC);
 290         status = spi_write_then_read(spi, &addr, sizeof(addr),
 291                         buf, sizeof(buf));
 292         if (status < 0)
 293                 return status;
 294
 295         dev_vdbg(dev, "%s: %02x %02x %02x %02x\n",
 296                 "alm0 read", buf[DS1305_SEC], buf[DS1305_MIN],
 297                 buf[DS1305_HOUR], buf[DS1305_WDAY]);
 298
 299         if ((DS1305_ALM_DISABLE & buf[DS1305_SEC])
 300                         || (DS1305_ALM_DISABLE & buf[DS1305_MIN])
 301                         || (DS1305_ALM_DISABLE & buf[DS1305_HOUR]))
 302                 return -EIO;
 303
 304         /* Stuff these values into alm->time and let RTC framework code
 305          * fill in the rest ... and also handle rollover to tomorrow when
 306          * that's needed.
 307          */
 308         alm->time.tm_sec = bcd2bin(buf[DS1305_SEC]);
 309         alm->time.tm_min = bcd2bin(buf[DS1305_MIN]);
 310         alm->time.tm_hour = bcd2hour(buf[DS1305_HOUR]);
 311
 312         return 0;
 313 }
 314
 315 /*
 316  * Context: caller holds rtc->ops_lock (to protect ds1305->ctrl)
 317  */
 318 static int ds1305_set_alarm(struct device *dev, struct rtc_wkalrm *alm)
 319 {
 320         struct ds1305   *ds1305 = dev_get_drvdata(dev);
 321         struct spi_device *spi = ds1305->spi;
 322         unsigned long   now, later;
 323         struct rtc_time tm;
 324         int             status;
 325         u8              buf[1 + DS1305_ALM_LEN];
 326
 327         /* convert desired alarm to time_t */
 328         later = rtc_tm_to_time64(&alm->time);
 329
 330         /* Read current time as time_t */
 331         status = ds1305_get_time(dev, &tm);
 332         if (status < 0)
 333                 return status;
 334         now = rtc_tm_to_time64(&tm);
 335
 336         /* make sure alarm fires within the next 24 hours */
 337         if (later <= now)
 338                 return -EINVAL;
 339         if ((later - now) > 24 * 60 * 60)
 340                 return -EDOM;
 341
 342         /* disable alarm if needed */
 343         if (ds1305->ctrl[0] & DS1305_AEI0) {
 344                 ds1305->ctrl[0] &= ~DS1305_AEI0;
 345
 346                 buf[0] = DS1305_WRITE | DS1305_CONTROL;
 347                 buf[1] = ds1305->ctrl[0];
 348                 status = spi_write_then_read(ds1305->spi, buf, 2, NULL, 0);
 349                 if (status < 0)
 350                         return status;
 351         }
 352
 353         /* write alarm */
 354         buf[0] = DS1305_WRITE | DS1305_ALM0(DS1305_SEC);
 355         buf[1 + DS1305_SEC] = bin2bcd(alm->time.tm_sec);
 356         buf[1 + DS1305_MIN] = bin2bcd(alm->time.tm_min);
 357         buf[1 + DS1305_HOUR] = hour2bcd(ds1305->hr12, alm->time.tm_hour);
 358         buf[1 + DS1305_WDAY] = DS1305_ALM_DISABLE;
 359
 360         dev_dbg(dev, "%s: %02x %02x %02x %02x\n",
 361                 "alm0 write", buf[1 + DS1305_SEC], buf[1 + DS1305_MIN],
 362                 buf[1 + DS1305_HOUR], buf[1 + DS1305_WDAY]);
 363
 364         status = spi_write_then_read(spi, buf, sizeof(buf), NULL, 0);
 365         if (status < 0)
 366                 return status;
 367
 368         /* enable alarm if requested */
 369         if (alm->enabled) {
 370                 ds1305->ctrl[0] |= DS1305_AEI0;
 371
 372                 buf[0] = DS1305_WRITE | DS1305_CONTROL;
 373                 buf[1] = ds1305->ctrl[0];
 374                 status = spi_write_then_read(ds1305->spi, buf, 2, NULL, 0);
 375         }
 376
 377         return status;
 378 }
 379
 380 #ifdef CONFIG_PROC_FS
 381
 382 static int ds1305_proc(struct device *dev, struct seq_file *seq)
 383 {
 384         struct ds1305   *ds1305 = dev_get_drvdata(dev);
 385         char            *diodes = "no";
 386         char            *resistors = "";
 387
 388         /* ctrl[2] is treated as read-only; no locking needed */
 389         if ((ds1305->ctrl[2] & 0xf0) == DS1305_TRICKLE_MAGIC) {
 390                 switch (ds1305->ctrl[2] & 0x0c) {
 391                 case DS1305_TRICKLE_DS2:
 392                         diodes = "2 diodes, ";
 393                         break;
 394                 case DS1305_TRICKLE_DS1:
 395                         diodes = "1 diode, ";
 396                         break;
 397                 default:
 398                         goto done;
 399                 }
 400                 switch (ds1305->ctrl[2] & 0x03) {
 401                 case DS1305_TRICKLE_2K:
 402                         resistors = "2k Ohm";
 403                         break;
 404                 case DS1305_TRICKLE_4K:
 405                         resistors = "4k Ohm";
 406                         break;
 407                 case DS1305_TRICKLE_8K:
 408                         resistors = "8k Ohm";
 409                         break;
 410                 default:
 411                         diodes = "no";
 412                         break;
 413                 }
 414         }
 415
 416 done:
 417         seq_printf(seq, "trickle_charge\t: %s%s\n", diodes, resistors);
 418
 419         return 0;
 420 }
 421
 422 #else
 423 #define ds1305_proc     NULL
 424 #endif
 425
 426 static const struct rtc_class_ops ds1305_ops = {
 427         .read_time      = ds1305_get_time,
 428         .set_time       = ds1305_set_time,
 429         .read_alarm     = ds1305_get_alarm,
 430         .set_alarm      = ds1305_set_alarm,
 431         .proc           = ds1305_proc,
 432         .alarm_irq_enable = ds1305_alarm_irq_enable,
 433 };
 434
 435 static void ds1305_work(struct work_struct *work)
 436 {
 437         struct ds1305   *ds1305 = container_of(work, struct ds1305, work);
 438         struct spi_device *spi = ds1305->spi;
 439         u8              buf[3];
 440         int             status;
 441
 442         /* lock to protect ds1305->ctrl */
 443         rtc_lock(ds1305->rtc);
 444
 445         /* Disable the IRQ, and clear its status ... for now, we "know"
 446          * that if more than one alarm is active, they're in sync.
 447          * Note that reading ALM data registers also clears IRQ status.
 448          */
 449         ds1305->ctrl[0] &= ~(DS1305_AEI1 | DS1305_AEI0);
 450         ds1305->ctrl[1] = 0;
 451
 452         buf[0] = DS1305_WRITE | DS1305_CONTROL;
 453         buf[1] = ds1305->ctrl[0];
 454         buf[2] = 0;
 455
 456         status = spi_write_then_read(spi, buf, sizeof(buf),
 457                         NULL, 0);
 458         if (status < 0)
 459                 dev_dbg(&spi->dev, "clear irq --> %d\n", status);
 460
 461         rtc_unlock(ds1305->rtc);
 462
 463         if (!test_bit(FLAG_EXITING, &ds1305->flags))
 464                 enable_irq(spi->irq);
 465
 466         rtc_update_irq(ds1305->rtc, 1, RTC_AF | RTC_IRQF);
 467 }
 468
 469 /*
 470  * This "real" IRQ handler hands off to a workqueue mostly to allow
 471  * mutex locking for ds1305->ctrl ... unlike I2C, we could issue async
 472  * I/O requests in IRQ context (to clear the IRQ status).
 473  */
 474 static irqreturn_t ds1305_irq(int irq, void *p)
 475 {
 476         struct ds1305           *ds1305 = p;
 477
 478         disable_irq(irq);
 479         schedule_work(&ds1305->work);
 480         return IRQ_HANDLED;
 481 }
 482
 483 /*----------------------------------------------------------------------*/
 484
 485 /*
 486  * Interface for NVRAM
 487  */
 488
 489 static void msg_init(struct spi_message *m, struct spi_transfer *x,
 490                 u8 *addr, size_t count, char *tx, char *rx)
 491 {
 492         spi_message_init(m);
 493         memset(x, 0, 2 * sizeof(*x));
 494
 495         x->tx_buf = addr;
 496         x->len = 1;
 497         spi_message_add_tail(x, m);
 498
 499         x++;
 500
 501         x->tx_buf = tx;
 502         x->rx_buf = rx;
 503         x->len = count;
 504         spi_message_add_tail(x, m);
 505 }
 506
 507 static int ds1305_nvram_read(void *priv, unsigned int off, void *buf,
 508                              size_t count)
 509 {
 510         struct ds1305           *ds1305 = priv;
 511         struct spi_device       *spi = ds1305->spi;
 512         u8                      addr;
 513         struct spi_message      m;
 514         struct spi_transfer     x[2];
 515
 516         addr = DS1305_NVRAM + off;
 517         msg_init(&m, x, &addr, count, NULL, buf);
 518
 519         return spi_sync(spi, &m);
 520 }
 521
 522 static int ds1305_nvram_write(void *priv, unsigned int off, void *buf,
 523                               size_t count)
 524 {
 525         struct ds1305           *ds1305 = priv;
 526         struct spi_device       *spi = ds1305->spi;
 527         u8                      addr;
 528         struct spi_message      m;
 529         struct spi_transfer     x[2];
 530
 531         addr = (DS1305_WRITE | DS1305_NVRAM) + off;
 532         msg_init(&m, x, &addr, count, buf, NULL);
 533
 534         return spi_sync(spi, &m);
 535 }
 536
 537 /*----------------------------------------------------------------------*/
 538
 539 /*
 540  * Interface to SPI stack
 541  */
 542
 543 static int ds1305_probe(struct spi_device *spi)
 544 {
 545         struct ds1305                   *ds1305;
 546         int                             status;
 547         u8                              addr, value;
 548         struct ds1305_platform_data     *pdata = dev_get_platdata(&spi->dev);
 549         bool                            write_ctrl = false;
 550         struct nvmem_config ds1305_nvmem_cfg = {
 551                 .name = "ds1305_nvram",
 552                 .word_size = 1,
 553                 .stride = 1,
 554                 .size = DS1305_NVRAM_LEN,
 555                 .reg_read = ds1305_nvram_read,
 556                 .reg_write = ds1305_nvram_write,
 557         };
 558
 559         /* Sanity check board setup data.  This may be hooked up
 560          * in 3wire mode, but we don't care.  Note that unless
 561          * there's an inverter in place, this needs SPI_CS_HIGH!
 562          */
 563         if ((spi->bits_per_word && spi->bits_per_word != 8)
 564                         || (spi->max_speed_hz > 2000000)
 565                         || !(spi->mode & SPI_CPHA))
 566                 return -EINVAL;
 567
 568         /* set up driver data */
 569         ds1305 = devm_kzalloc(&spi->dev, sizeof(*ds1305), GFP_KERNEL);
 570         if (!ds1305)
 571                 return -ENOMEM;
 572         ds1305->spi = spi;
 573         spi_set_drvdata(spi, ds1305);
 574
 575         /* read and cache control registers */
 576         addr = DS1305_CONTROL;
 577         status = spi_write_then_read(spi, &addr, sizeof(addr),
 578                         ds1305->ctrl, sizeof(ds1305->ctrl));
 579         if (status < 0) {
 580                 dev_dbg(&spi->dev, "can't %s, %d\n",
 581                                 "read", status);
 582                 return status;
 583         }
 584
 585         dev_dbg(&spi->dev, "ctrl %s: %3ph\n", "read", ds1305->ctrl);
 586
 587         /* Sanity check register values ... partially compensating for the
 588          * fact that SPI has no device handshake.  A pullup on MISO would
 589          * make these tests fail; but not all systems will have one.  If
 590          * some register is neither 0x00 nor 0xff, a chip is likely there.
 591          */
 592         if ((ds1305->ctrl[0] & 0x38) != 0 || (ds1305->ctrl[1] & 0xfc) != 0) {
 593                 dev_dbg(&spi->dev, "RTC chip is not present\n");
 594                 return -ENODEV;
 595         }
 596         if (ds1305->ctrl[2] == 0)
 597                 dev_dbg(&spi->dev, "chip may not be present\n");
 598
 599         /* enable writes if needed ... if we were paranoid it would
 600          * make sense to enable them only when absolutely necessary.
 601          */
 602         if (ds1305->ctrl[0] & DS1305_WP) {
 603                 u8              buf[2];
 604
 605                 ds1305->ctrl[0] &= ~DS1305_WP;
 606
 607                 buf[0] = DS1305_WRITE | DS1305_CONTROL;
 608                 buf[1] = ds1305->ctrl[0];
 609                 status = spi_write_then_read(spi, buf, sizeof(buf), NULL, 0);
 610
 611                 dev_dbg(&spi->dev, "clear WP --> %d\n", status);
 612                 if (status < 0)
 613                         return status;
 614         }
 615
 616         /* on DS1305, maybe start oscillator; like most low power
 617          * oscillators, it may take a second to stabilize
 618          */
 619         if (ds1305->ctrl[0] & DS1305_nEOSC) {
 620                 ds1305->ctrl[0] &= ~DS1305_nEOSC;
 621                 write_ctrl = true;
 622                 dev_warn(&spi->dev, "SET TIME!\n");
 623         }
 624
 625         /* ack any pending IRQs */
 626         if (ds1305->ctrl[1]) {
 627                 ds1305->ctrl[1] = 0;
 628                 write_ctrl = true;
 629         }
 630
 631         /* this may need one-time (re)init */
 632         if (pdata) {
 633                 /* maybe enable trickle charge */
 634                 if (((ds1305->ctrl[2] & 0xf0) != DS1305_TRICKLE_MAGIC)) {
 635                         ds1305->ctrl[2] = DS1305_TRICKLE_MAGIC
 636                                                 | pdata->trickle;
 637                         write_ctrl = true;
 638                 }
 639
 640                 /* on DS1306, configure 1 Hz signal */
 641                 if (pdata->is_ds1306) {
 642                         if (pdata->en_1hz) {
 643                                 if (!(ds1305->ctrl[0] & DS1306_1HZ)) {
 644                                         ds1305->ctrl[0] |= DS1306_1HZ;
 645                                         write_ctrl = true;
 646                                 }
 647                         } else {
 648                                 if (ds1305->ctrl[0] & DS1306_1HZ) {
 649                                         ds1305->ctrl[0] &= ~DS1306_1HZ;
 650                                         write_ctrl = true;
 651                                 }
 652                         }
 653                 }
 654         }
 655
 656         if (write_ctrl) {
 657                 u8              buf[4];
 658
 659                 buf[0] = DS1305_WRITE | DS1305_CONTROL;
 660                 buf[1] = ds1305->ctrl[0];
 661                 buf[2] = ds1305->ctrl[1];
 662                 buf[3] = ds1305->ctrl[2];
 663                 status = spi_write_then_read(spi, buf, sizeof(buf), NULL, 0);
 664                 if (status < 0) {
 665                         dev_dbg(&spi->dev, "can't %s, %d\n",
 666                                         "write", status);
 667                         return status;
 668                 }
 669
 670                 dev_dbg(&spi->dev, "ctrl %s: %3ph\n", "write", ds1305->ctrl);
 671         }
 672
 673         /* see if non-Linux software set up AM/PM mode */
 674         addr = DS1305_HOUR;
 675         status = spi_write_then_read(spi, &addr, sizeof(addr),
 676                                 &value, sizeof(value));
 677         if (status < 0) {
 678                 dev_dbg(&spi->dev, "read HOUR --> %d\n", status);
 679                 return status;
 680         }
 681
 682         ds1305->hr12 = (DS1305_HR_12 & value) != 0;
 683         if (ds1305->hr12)
 684                 dev_dbg(&spi->dev, "AM/PM\n");
 685
 686         /* register RTC ... from here on, ds1305->ctrl needs locking */
 687         ds1305->rtc = devm_rtc_allocate_device(&spi->dev);
 688         if (IS_ERR(ds1305->rtc))
 689                 return PTR_ERR(ds1305->rtc);
 690
 691         ds1305->rtc->ops = &ds1305_ops;
 692         ds1305->rtc->range_min = RTC_TIMESTAMP_BEGIN_2000;
 693         ds1305->rtc->range_max = RTC_TIMESTAMP_END_2099;
 694
 695         ds1305_nvmem_cfg.priv = ds1305;
 696         status = devm_rtc_register_device(ds1305->rtc);
 697         if (status)
 698                 return status;
 699
 700         devm_rtc_nvmem_register(ds1305->rtc, &ds1305_nvmem_cfg);
 701
 702         /* Maybe set up alarm IRQ; be ready to handle it triggering right
 703          * away.  NOTE that we don't share this.  The signal is active low,
 704          * and we can't ack it before a SPI message delay.  We temporarily
 705          * disable the IRQ until it's acked, which lets us work with more
 706          * IRQ trigger modes (not all IRQ controllers can do falling edge).
 707          */
 708         if (spi->irq) {
 709                 INIT_WORK(&ds1305->work, ds1305_work);
 710                 status = devm_request_irq(&spi->dev, spi->irq, ds1305_irq,
 711                                 0, dev_name(&ds1305->rtc->dev), ds1305);
 712                 if (status < 0) {
 713                         dev_err(&spi->dev, "request_irq %d --> %d\n",
 714                                         spi->irq, status);
 715                 } else {
 716                         device_set_wakeup_capable(&spi->dev, 1);
 717                 }
 718         }
 719
 720         return 0;
 721 }
 722
 723 static int ds1305_remove(struct spi_device *spi)
 724 {
 725         struct ds1305 *ds1305 = spi_get_drvdata(spi);
 726
 727         /* carefully shut down irq and workqueue, if present */
 728         if (spi->irq) {
 729                 set_bit(FLAG_EXITING, &ds1305->flags);
 730                 devm_free_irq(&spi->dev, spi->irq, ds1305);
 731                 cancel_work_sync(&ds1305->work);
 732         }
 733
 734         return 0;
 735 }
 736
 737 static struct spi_driver ds1305_driver = {
 738         .driver.name    = "rtc-ds1305",
 739         .probe          = ds1305_probe,
 740         .remove         = ds1305_remove,
 741         /* REVISIT add suspend/resume */
 742 };
 743
 744 module_spi_driver(ds1305_driver);
 745
 746 MODULE_DESCRIPTION("RTC driver for DS1305 and DS1306 chips");
 747 MODULE_LICENSE("GPL");
 748 MODULE_ALIAS("spi:rtc-ds1305");