15dd007700c21825fcee39040e03f8c549b994bc
[linux-2.6-microblaze.git] / drivers / pinctrl / sh-pfc / pinctrl-rza1.c
1 // SPDX-License-Identifier: GPL-2.0
2 /*
3  * Combined GPIO and pin controller support for Renesas RZ/A1 (r7s72100) SoC
4  *
5  * Copyright (C) 2017 Jacopo Mondi
6  */
7
8 /*
9  * This pin controller/gpio combined driver supports Renesas devices of RZ/A1
10  * family.
11  * This includes SoCs which are sub- or super- sets of this particular line,
12  * as RZ/A1H (r7s721000), RZ/A1M (r7s721010) and RZ/A1L (r7s721020).
13  */
14
15 #include <linux/bitops.h>
16 #include <linux/err.h>
17 #include <linux/gpio/driver.h>
18 #include <linux/init.h>
19 #include <linux/ioport.h>
20 #include <linux/module.h>
21 #include <linux/of.h>
22 #include <linux/of_address.h>
23 #include <linux/of_device.h>
24 #include <linux/pinctrl/pinconf-generic.h>
25 #include <linux/pinctrl/pinctrl.h>
26 #include <linux/pinctrl/pinmux.h>
27 #include <linux/slab.h>
28
29 #include "../core.h"
30 #include "../devicetree.h"
31 #include "../pinconf.h"
32 #include "../pinmux.h"
33
34 #define DRIVER_NAME                     "pinctrl-rza1"
35
36 #define RZA1_P_REG                      0x0000
37 #define RZA1_PPR_REG                    0x0200
38 #define RZA1_PM_REG                     0x0300
39 #define RZA1_PMC_REG                    0x0400
40 #define RZA1_PFC_REG                    0x0500
41 #define RZA1_PFCE_REG                   0x0600
42 #define RZA1_PFCEA_REG                  0x0a00
43 #define RZA1_PIBC_REG                   0x4000
44 #define RZA1_PBDC_REG                   0x4100
45 #define RZA1_PIPC_REG                   0x4200
46
47 #define RZA1_ADDR(mem, reg, port)       ((mem) + (reg) + ((port) * 4))
48
49 #define RZA1_NPORTS                     12
50 #define RZA1_PINS_PER_PORT              16
51 #define RZA1_NPINS                      (RZA1_PINS_PER_PORT * RZA1_NPORTS)
52 #define RZA1_PIN_ID_TO_PORT(id)         ((id) / RZA1_PINS_PER_PORT)
53 #define RZA1_PIN_ID_TO_PIN(id)          ((id) % RZA1_PINS_PER_PORT)
54
55 /*
56  * Use 16 lower bits [15:0] for pin identifier
57  * Use 16 higher bits [31:16] for pin mux function
58  */
59 #define MUX_PIN_ID_MASK                 GENMASK(15, 0)
60 #define MUX_FUNC_MASK                   GENMASK(31, 16)
61
62 #define MUX_FUNC_OFFS                   16
63 #define MUX_FUNC(pinconf)               \
64         ((pinconf & MUX_FUNC_MASK) >> MUX_FUNC_OFFS)
65 #define MUX_FUNC_PFC_MASK               BIT(0)
66 #define MUX_FUNC_PFCE_MASK              BIT(1)
67 #define MUX_FUNC_PFCEA_MASK             BIT(2)
68
69 /* Pin mux flags */
70 #define MUX_FLAGS_BIDIR                 BIT(0)
71 #define MUX_FLAGS_SWIO_INPUT            BIT(1)
72 #define MUX_FLAGS_SWIO_OUTPUT           BIT(2)
73
74 /* ----------------------------------------------------------------------------
75  * RZ/A1 pinmux flags
76  */
77
78 /*
79  * rza1_bidir_pin - describe a single pin that needs bidir flag applied.
80  */
81 struct rza1_bidir_pin {
82         u8 pin: 4;
83         u8 func: 4;
84 };
85
86 /*
87  * rza1_bidir_entry - describe a list of pins that needs bidir flag applied.
88  *                    Each struct rza1_bidir_entry describes a port.
89  */
90 struct rza1_bidir_entry {
91         const unsigned int npins;
92         const struct rza1_bidir_pin *pins;
93 };
94
95 /*
96  * rza1_swio_pin - describe a single pin that needs swio flag applied.
97  */
98 struct rza1_swio_pin {
99         u16 pin: 4;
100         u16 port: 4;
101         u16 func: 4;
102         u16 input: 1;
103 };
104
105 /*
106  * rza1_swio_entry - describe a list of pins that needs swio flag applied
107  */
108 struct rza1_swio_entry {
109         const unsigned int npins;
110         const struct rza1_swio_pin *pins;
111 };
112
113 /*
114  * rza1_pinmux_conf - group together bidir and swio pinmux flag tables
115  */
116 struct rza1_pinmux_conf {
117         const struct rza1_bidir_entry *bidir_entries;
118         const struct rza1_swio_entry *swio_entries;
119 };
120
121 /* ----------------------------------------------------------------------------
122  * RZ/A1H (r7s72100) pinmux flags
123  */
124
125 static const struct rza1_bidir_pin rza1h_bidir_pins_p1[] = {
126         { .pin = 0, .func = 1 },
127         { .pin = 1, .func = 1 },
128         { .pin = 2, .func = 1 },
129         { .pin = 3, .func = 1 },
130         { .pin = 4, .func = 1 },
131         { .pin = 5, .func = 1 },
132         { .pin = 6, .func = 1 },
133         { .pin = 7, .func = 1 },
134 };
135
136 static const struct rza1_bidir_pin rza1h_bidir_pins_p2[] = {
137         { .pin = 0, .func = 1 },
138         { .pin = 1, .func = 1 },
139         { .pin = 2, .func = 1 },
140         { .pin = 3, .func = 1 },
141         { .pin = 4, .func = 1 },
142         { .pin = 0, .func = 4 },
143         { .pin = 1, .func = 4 },
144         { .pin = 2, .func = 4 },
145         { .pin = 3, .func = 4 },
146         { .pin = 5, .func = 1 },
147         { .pin = 6, .func = 1 },
148         { .pin = 7, .func = 1 },
149         { .pin = 8, .func = 1 },
150         { .pin = 9, .func = 1 },
151         { .pin = 10, .func = 1 },
152         { .pin = 11, .func = 1 },
153         { .pin = 12, .func = 1 },
154         { .pin = 13, .func = 1 },
155         { .pin = 14, .func = 1 },
156         { .pin = 15, .func = 1 },
157         { .pin = 12, .func = 4 },
158         { .pin = 13, .func = 4 },
159         { .pin = 14, .func = 4 },
160         { .pin = 15, .func = 4 },
161 };
162
163 static const struct rza1_bidir_pin rza1h_bidir_pins_p3[] = {
164         { .pin = 3, .func = 2 },
165         { .pin = 10, .func = 7 },
166         { .pin = 11, .func = 7 },
167         { .pin = 13, .func = 7 },
168         { .pin = 14, .func = 7 },
169         { .pin = 15, .func = 7 },
170         { .pin = 10, .func = 8 },
171         { .pin = 11, .func = 8 },
172         { .pin = 13, .func = 8 },
173         { .pin = 14, .func = 8 },
174         { .pin = 15, .func = 8 },
175 };
176
177 static const struct rza1_bidir_pin rza1h_bidir_pins_p4[] = {
178         { .pin = 0, .func = 8 },
179         { .pin = 1, .func = 8 },
180         { .pin = 2, .func = 8 },
181         { .pin = 3, .func = 8 },
182         { .pin = 10, .func = 3 },
183         { .pin = 11, .func = 3 },
184         { .pin = 13, .func = 3 },
185         { .pin = 14, .func = 3 },
186         { .pin = 15, .func = 3 },
187         { .pin = 10, .func = 4 },
188         { .pin = 11, .func = 4 },
189         { .pin = 13, .func = 4 },
190         { .pin = 14, .func = 4 },
191         { .pin = 15, .func = 4 },
192         { .pin = 12, .func = 5 },
193         { .pin = 13, .func = 5 },
194         { .pin = 14, .func = 5 },
195         { .pin = 15, .func = 5 },
196 };
197
198 static const struct rza1_bidir_pin rza1h_bidir_pins_p6[] = {
199         { .pin = 0, .func = 1 },
200         { .pin = 1, .func = 1 },
201         { .pin = 2, .func = 1 },
202         { .pin = 3, .func = 1 },
203         { .pin = 4, .func = 1 },
204         { .pin = 5, .func = 1 },
205         { .pin = 6, .func = 1 },
206         { .pin = 7, .func = 1 },
207         { .pin = 8, .func = 1 },
208         { .pin = 9, .func = 1 },
209         { .pin = 10, .func = 1 },
210         { .pin = 11, .func = 1 },
211         { .pin = 12, .func = 1 },
212         { .pin = 13, .func = 1 },
213         { .pin = 14, .func = 1 },
214         { .pin = 15, .func = 1 },
215 };
216
217 static const struct rza1_bidir_pin rza1h_bidir_pins_p7[] = {
218         { .pin = 13, .func = 3 },
219 };
220
221 static const struct rza1_bidir_pin rza1h_bidir_pins_p8[] = {
222         { .pin = 8, .func = 3 },
223         { .pin = 9, .func = 3 },
224         { .pin = 10, .func = 3 },
225         { .pin = 11, .func = 3 },
226         { .pin = 14, .func = 2 },
227         { .pin = 15, .func = 2 },
228         { .pin = 14, .func = 3 },
229         { .pin = 15, .func = 3 },
230 };
231
232 static const struct rza1_bidir_pin rza1h_bidir_pins_p9[] = {
233         { .pin = 0, .func = 2 },
234         { .pin = 1, .func = 2 },
235         { .pin = 4, .func = 2 },
236         { .pin = 5, .func = 2 },
237         { .pin = 6, .func = 2 },
238         { .pin = 7, .func = 2 },
239 };
240
241 static const struct rza1_bidir_pin rza1h_bidir_pins_p11[] = {
242         { .pin = 6, .func = 2 },
243         { .pin = 7, .func = 2 },
244         { .pin = 9, .func = 2 },
245         { .pin = 6, .func = 4 },
246         { .pin = 7, .func = 4 },
247         { .pin = 9, .func = 4 },
248         { .pin = 10, .func = 2 },
249         { .pin = 11, .func = 2 },
250         { .pin = 10, .func = 4 },
251         { .pin = 11, .func = 4 },
252         { .pin = 12, .func = 4 },
253         { .pin = 13, .func = 4 },
254         { .pin = 14, .func = 4 },
255         { .pin = 15, .func = 4 },
256 };
257
258 static const struct rza1_swio_pin rza1h_swio_pins[] = {
259         { .port = 2, .pin = 7, .func = 4, .input = 0 },
260         { .port = 2, .pin = 11, .func = 4, .input = 0 },
261         { .port = 3, .pin = 7, .func = 3, .input = 0 },
262         { .port = 3, .pin = 7, .func = 8, .input = 0 },
263         { .port = 4, .pin = 7, .func = 5, .input = 0 },
264         { .port = 4, .pin = 7, .func = 11, .input = 0 },
265         { .port = 4, .pin = 15, .func = 6, .input = 0 },
266         { .port = 5, .pin = 0, .func = 1, .input = 1 },
267         { .port = 5, .pin = 1, .func = 1, .input = 1 },
268         { .port = 5, .pin = 2, .func = 1, .input = 1 },
269         { .port = 5, .pin = 3, .func = 1, .input = 1 },
270         { .port = 5, .pin = 4, .func = 1, .input = 1 },
271         { .port = 5, .pin = 5, .func = 1, .input = 1 },
272         { .port = 5, .pin = 6, .func = 1, .input = 1 },
273         { .port = 5, .pin = 7, .func = 1, .input = 1 },
274         { .port = 7, .pin = 4, .func = 6, .input = 0 },
275         { .port = 7, .pin = 11, .func = 2, .input = 0 },
276         { .port = 8, .pin = 10, .func = 8, .input = 0 },
277         { .port = 10, .pin = 15, .func = 2, .input = 0 },
278 };
279
280 static const struct rza1_bidir_entry rza1h_bidir_entries[RZA1_NPORTS] = {
281         [1] = { ARRAY_SIZE(rza1h_bidir_pins_p1), rza1h_bidir_pins_p1 },
282         [2] = { ARRAY_SIZE(rza1h_bidir_pins_p2), rza1h_bidir_pins_p2 },
283         [3] = { ARRAY_SIZE(rza1h_bidir_pins_p3), rza1h_bidir_pins_p3 },
284         [4] = { ARRAY_SIZE(rza1h_bidir_pins_p4), rza1h_bidir_pins_p4 },
285         [6] = { ARRAY_SIZE(rza1h_bidir_pins_p6), rza1h_bidir_pins_p6 },
286         [7] = { ARRAY_SIZE(rza1h_bidir_pins_p7), rza1h_bidir_pins_p7 },
287         [8] = { ARRAY_SIZE(rza1h_bidir_pins_p8), rza1h_bidir_pins_p8 },
288         [9] = { ARRAY_SIZE(rza1h_bidir_pins_p9), rza1h_bidir_pins_p9 },
289         [11] = { ARRAY_SIZE(rza1h_bidir_pins_p11), rza1h_bidir_pins_p11 },
290 };
291
292 static const struct rza1_swio_entry rza1h_swio_entries[] = {
293         [0] = { ARRAY_SIZE(rza1h_swio_pins), rza1h_swio_pins },
294 };
295
296 /* RZ/A1H (r7s72100x) pinmux flags table */
297 static const struct rza1_pinmux_conf rza1h_pmx_conf = {
298         .bidir_entries  = rza1h_bidir_entries,
299         .swio_entries   = rza1h_swio_entries,
300 };
301
302 /* ----------------------------------------------------------------------------
303  * RZ/A1L (r7s72102) pinmux flags
304  */
305
306 static const struct rza1_bidir_pin rza1l_bidir_pins_p1[] = {
307         { .pin = 0, .func = 1 },
308         { .pin = 1, .func = 1 },
309         { .pin = 2, .func = 1 },
310         { .pin = 3, .func = 1 },
311         { .pin = 4, .func = 1 },
312         { .pin = 5, .func = 1 },
313         { .pin = 6, .func = 1 },
314         { .pin = 7, .func = 1 },
315 };
316
317 static const struct rza1_bidir_pin rza1l_bidir_pins_p3[] = {
318         { .pin = 0, .func = 2 },
319         { .pin = 1, .func = 2 },
320         { .pin = 2, .func = 2 },
321         { .pin = 4, .func = 2 },
322         { .pin = 5, .func = 2 },
323         { .pin = 10, .func = 2 },
324         { .pin = 11, .func = 2 },
325         { .pin = 12, .func = 2 },
326         { .pin = 13, .func = 2 },
327 };
328
329 static const struct rza1_bidir_pin rza1l_bidir_pins_p4[] = {
330         { .pin = 1, .func = 4 },
331         { .pin = 2, .func = 2 },
332         { .pin = 3, .func = 2 },
333         { .pin = 6, .func = 2 },
334         { .pin = 7, .func = 2 },
335 };
336
337 static const struct rza1_bidir_pin rza1l_bidir_pins_p5[] = {
338         { .pin = 0, .func = 1 },
339         { .pin = 1, .func = 1 },
340         { .pin = 2, .func = 1 },
341         { .pin = 3, .func = 1 },
342         { .pin = 4, .func = 1 },
343         { .pin = 5, .func = 1 },
344         { .pin = 6, .func = 1 },
345         { .pin = 7, .func = 1 },
346         { .pin = 8, .func = 1 },
347         { .pin = 9, .func = 1 },
348         { .pin = 10, .func = 1 },
349         { .pin = 11, .func = 1 },
350         { .pin = 12, .func = 1 },
351         { .pin = 13, .func = 1 },
352         { .pin = 14, .func = 1 },
353         { .pin = 15, .func = 1 },
354         { .pin = 0, .func = 2 },
355         { .pin = 1, .func = 2 },
356         { .pin = 2, .func = 2 },
357         { .pin = 3, .func = 2 },
358 };
359
360 static const struct rza1_bidir_pin rza1l_bidir_pins_p6[] = {
361         { .pin = 0, .func = 1 },
362         { .pin = 1, .func = 1 },
363         { .pin = 2, .func = 1 },
364         { .pin = 3, .func = 1 },
365         { .pin = 4, .func = 1 },
366         { .pin = 5, .func = 1 },
367         { .pin = 6, .func = 1 },
368         { .pin = 7, .func = 1 },
369         { .pin = 8, .func = 1 },
370         { .pin = 9, .func = 1 },
371         { .pin = 10, .func = 1 },
372         { .pin = 11, .func = 1 },
373         { .pin = 12, .func = 1 },
374         { .pin = 13, .func = 1 },
375         { .pin = 14, .func = 1 },
376         { .pin = 15, .func = 1 },
377 };
378
379 static const struct rza1_bidir_pin rza1l_bidir_pins_p7[] = {
380         { .pin = 2, .func = 2 },
381         { .pin = 3, .func = 2 },
382         { .pin = 5, .func = 2 },
383         { .pin = 6, .func = 2 },
384         { .pin = 7, .func = 2 },
385         { .pin = 2, .func = 3 },
386         { .pin = 3, .func = 3 },
387         { .pin = 5, .func = 3 },
388         { .pin = 6, .func = 3 },
389         { .pin = 7, .func = 3 },
390 };
391
392 static const struct rza1_bidir_pin rza1l_bidir_pins_p9[] = {
393         { .pin = 1, .func = 2 },
394         { .pin = 0, .func = 3 },
395         { .pin = 1, .func = 3 },
396         { .pin = 3, .func = 3 },
397         { .pin = 4, .func = 3 },
398         { .pin = 5, .func = 3 },
399 };
400
401 static const struct rza1_swio_pin rza1l_swio_pins[] = {
402         { .port = 2, .pin = 8, .func = 2, .input = 0 },
403         { .port = 5, .pin = 6, .func = 3, .input = 0 },
404         { .port = 6, .pin = 6, .func = 3, .input = 0 },
405         { .port = 6, .pin = 10, .func = 3, .input = 0 },
406         { .port = 7, .pin = 10, .func = 2, .input = 0 },
407         { .port = 8, .pin = 2, .func = 3, .input = 0 },
408 };
409
410 static const struct rza1_bidir_entry rza1l_bidir_entries[RZA1_NPORTS] = {
411         [1] = { ARRAY_SIZE(rza1l_bidir_pins_p1), rza1l_bidir_pins_p1 },
412         [3] = { ARRAY_SIZE(rza1l_bidir_pins_p3), rza1l_bidir_pins_p3 },
413         [4] = { ARRAY_SIZE(rza1l_bidir_pins_p4), rza1l_bidir_pins_p4 },
414         [5] = { ARRAY_SIZE(rza1l_bidir_pins_p4), rza1l_bidir_pins_p5 },
415         [6] = { ARRAY_SIZE(rza1l_bidir_pins_p6), rza1l_bidir_pins_p6 },
416         [7] = { ARRAY_SIZE(rza1l_bidir_pins_p7), rza1l_bidir_pins_p7 },
417         [9] = { ARRAY_SIZE(rza1l_bidir_pins_p9), rza1l_bidir_pins_p9 },
418 };
419
420 static const struct rza1_swio_entry rza1l_swio_entries[] = {
421         [0] = { ARRAY_SIZE(rza1l_swio_pins), rza1l_swio_pins },
422 };
423
424 /* RZ/A1L (r7s72102x) pinmux flags table */
425 static const struct rza1_pinmux_conf rza1l_pmx_conf = {
426         .bidir_entries  = rza1l_bidir_entries,
427         .swio_entries   = rza1l_swio_entries,
428 };
429
430 /* ----------------------------------------------------------------------------
431  * RZ/A1 types
432  */
433 /**
434  * struct rza1_mux_conf - describes a pin multiplexing operation
435  *
436  * @id: the pin identifier from 0 to RZA1_NPINS
437  * @port: the port where pin sits on
438  * @pin: pin id
439  * @mux_func: alternate function id number
440  * @mux_flags: alternate function flags
441  * @value: output value to set the pin to
442  */
443 struct rza1_mux_conf {
444         u16 id;
445         u8 port;
446         u8 pin;
447         u8 mux_func;
448         u8 mux_flags;
449         u8 value;
450 };
451
452 /**
453  * struct rza1_port - describes a pin port
454  *
455  * This is mostly useful to lock register writes per-bank and not globally.
456  *
457  * @lock: protect access to HW registers
458  * @id: port number
459  * @base: logical address base
460  * @pins: pins sitting on this port
461  */
462 struct rza1_port {
463         spinlock_t lock;
464         unsigned int id;
465         void __iomem *base;
466         struct pinctrl_pin_desc *pins;
467 };
468
469 /**
470  * struct rza1_pinctrl - RZ pincontroller device
471  *
472  * @dev: parent device structure
473  * @mutex: protect [pinctrl|pinmux]_generic functions
474  * @base: logical address base
475  * @nport: number of pin controller ports
476  * @ports: pin controller banks
477  * @pins: pin array for pinctrl core
478  * @desc: pincontroller desc for pinctrl core
479  * @pctl: pinctrl device
480  * @data: device specific data
481  */
482 struct rza1_pinctrl {
483         struct device *dev;
484
485         struct mutex mutex;
486
487         void __iomem *base;
488
489         unsigned int nport;
490         struct rza1_port *ports;
491
492         struct pinctrl_pin_desc *pins;
493         struct pinctrl_desc desc;
494         struct pinctrl_dev *pctl;
495
496         const void *data;
497 };
498
499 /* ----------------------------------------------------------------------------
500  * RZ/A1 pinmux flags
501  */
502 static inline bool rza1_pinmux_get_bidir(unsigned int port,
503                                          unsigned int pin,
504                                          unsigned int func,
505                                          const struct rza1_bidir_entry *table)
506 {
507         const struct rza1_bidir_entry *entry = &table[port];
508         const struct rza1_bidir_pin *bidir_pin;
509         unsigned int i;
510
511         for (i = 0; i < entry->npins; ++i) {
512                 bidir_pin = &entry->pins[i];
513                 if (bidir_pin->pin == pin && bidir_pin->func == func)
514                         return true;
515         }
516
517         return false;
518 }
519
520 static inline int rza1_pinmux_get_swio(unsigned int port,
521                                        unsigned int pin,
522                                        unsigned int func,
523                                        const struct rza1_swio_entry *table)
524 {
525         const struct rza1_swio_pin *swio_pin;
526         unsigned int i;
527
528
529         for (i = 0; i < table->npins; ++i) {
530                 swio_pin = &table->pins[i];
531                 if (swio_pin->port == port && swio_pin->pin == pin &&
532                     swio_pin->func == func)
533                         return swio_pin->input;
534         }
535
536         return -ENOENT;
537 }
538
539 /*
540  * rza1_pinmux_get_flags() - return pinmux flags associated to a pin
541  */
542 static unsigned int rza1_pinmux_get_flags(unsigned int port, unsigned int pin,
543                                           unsigned int func,
544                                           struct rza1_pinctrl *rza1_pctl)
545
546 {
547         const struct rza1_pinmux_conf *pmx_conf = rza1_pctl->data;
548         const struct rza1_bidir_entry *bidir_entries = pmx_conf->bidir_entries;
549         const struct rza1_swio_entry *swio_entries = pmx_conf->swio_entries;
550         unsigned int pmx_flags = 0;
551         int ret;
552
553         if (rza1_pinmux_get_bidir(port, pin, func, bidir_entries))
554                 pmx_flags |= MUX_FLAGS_BIDIR;
555
556         ret = rza1_pinmux_get_swio(port, pin, func, swio_entries);
557         if (ret == 0)
558                 pmx_flags |= MUX_FLAGS_SWIO_OUTPUT;
559         else if (ret > 0)
560                 pmx_flags |= MUX_FLAGS_SWIO_INPUT;
561
562         return pmx_flags;
563 }
564
565 /* ----------------------------------------------------------------------------
566  * RZ/A1 SoC operations
567  */
568
569 /*
570  * rza1_set_bit() - un-locked set/clear a single bit in pin configuration
571  *                  registers
572  */
573 static inline void rza1_set_bit(struct rza1_port *port, unsigned int reg,
574                                 unsigned int bit, bool set)
575 {
576         void __iomem *mem = RZA1_ADDR(port->base, reg, port->id);
577         u16 val = ioread16(mem);
578
579         if (set)
580                 val |= BIT(bit);
581         else
582                 val &= ~BIT(bit);
583
584         iowrite16(val, mem);
585 }
586
587 static inline unsigned int rza1_get_bit(struct rza1_port *port,
588                                         unsigned int reg, unsigned int bit)
589 {
590         void __iomem *mem = RZA1_ADDR(port->base, reg, port->id);
591
592         return ioread16(mem) & BIT(bit);
593 }
594
595 /**
596  * rza1_pin_reset() - reset a pin to default initial state
597  *
598  * Reset pin state disabling input buffer and bi-directional control,
599  * and configure it as input port.
600  * Note that pin is now configured with direction as input but with input
601  * buffer disabled. This implies the pin value cannot be read in this state.
602  *
603  * @port: port where pin sits on
604  * @pin: pin offset
605  */
606 static void rza1_pin_reset(struct rza1_port *port, unsigned int pin)
607 {
608         unsigned long irqflags;
609
610         spin_lock_irqsave(&port->lock, irqflags);
611         rza1_set_bit(port, RZA1_PIBC_REG, pin, 0);
612         rza1_set_bit(port, RZA1_PBDC_REG, pin, 0);
613
614         rza1_set_bit(port, RZA1_PM_REG, pin, 1);
615         rza1_set_bit(port, RZA1_PMC_REG, pin, 0);
616         rza1_set_bit(port, RZA1_PIPC_REG, pin, 0);
617         spin_unlock_irqrestore(&port->lock, irqflags);
618 }
619
620 /**
621  * rza1_pin_set_direction() - set I/O direction on a pin in port mode
622  *
623  * When running in output port mode keep PBDC enabled to allow reading the
624  * pin value from PPR.
625  *
626  * @port: port where pin sits on
627  * @pin: pin offset
628  * @input: input enable/disable flag
629  */
630 static inline void rza1_pin_set_direction(struct rza1_port *port,
631                                           unsigned int pin, bool input)
632 {
633         unsigned long irqflags;
634
635         spin_lock_irqsave(&port->lock, irqflags);
636
637         rza1_set_bit(port, RZA1_PIBC_REG, pin, 1);
638         if (input) {
639                 rza1_set_bit(port, RZA1_PM_REG, pin, 1);
640                 rza1_set_bit(port, RZA1_PBDC_REG, pin, 0);
641         } else {
642                 rza1_set_bit(port, RZA1_PM_REG, pin, 0);
643                 rza1_set_bit(port, RZA1_PBDC_REG, pin, 1);
644         }
645
646         spin_unlock_irqrestore(&port->lock, irqflags);
647 }
648
649 static inline void rza1_pin_set(struct rza1_port *port, unsigned int pin,
650                                 unsigned int value)
651 {
652         unsigned long irqflags;
653
654         spin_lock_irqsave(&port->lock, irqflags);
655         rza1_set_bit(port, RZA1_P_REG, pin, !!value);
656         spin_unlock_irqrestore(&port->lock, irqflags);
657 }
658
659 static inline int rza1_pin_get(struct rza1_port *port, unsigned int pin)
660 {
661         return rza1_get_bit(port, RZA1_PPR_REG, pin);
662 }
663
664 /**
665  * rza1_pin_mux_single() - configure pin multiplexing on a single pin
666  *
667  * @rza1_pctl: RZ/A1 pin controller device
668  * @mux_conf: pin multiplexing descriptor
669  */
670 static int rza1_pin_mux_single(struct rza1_pinctrl *rza1_pctl,
671                                struct rza1_mux_conf *mux_conf)
672 {
673         struct rza1_port *port = &rza1_pctl->ports[mux_conf->port];
674         unsigned int pin = mux_conf->pin;
675         u8 mux_func = mux_conf->mux_func;
676         u8 mux_flags = mux_conf->mux_flags;
677         u8 mux_flags_from_table;
678
679         rza1_pin_reset(port, pin);
680
681         /* SWIO pinmux flags coming from DT are high precedence */
682         mux_flags_from_table = rza1_pinmux_get_flags(port->id, pin, mux_func,
683                                                      rza1_pctl);
684         if (mux_flags)
685                 mux_flags |= (mux_flags_from_table & MUX_FLAGS_BIDIR);
686         else
687                 mux_flags = mux_flags_from_table;
688
689         if (mux_flags & MUX_FLAGS_BIDIR)
690                 rza1_set_bit(port, RZA1_PBDC_REG, pin, 1);
691
692         /*
693          * Enable alternate function mode and select it.
694          *
695          * Be careful here: the pin mux sub-nodes in device tree
696          * enumerate alternate functions from 1 to 8;
697          * subtract 1 before using macros to match registers configuration
698          * which expects numbers from 0 to 7 instead.
699          *
700          * ----------------------------------------------------
701          * Alternate mode selection table:
702          *
703          * PMC  PFC     PFCE    PFCAE   (mux_func - 1)
704          * 1    0       0       0       0
705          * 1    1       0       0       1
706          * 1    0       1       0       2
707          * 1    1       1       0       3
708          * 1    0       0       1       4
709          * 1    1       0       1       5
710          * 1    0       1       1       6
711          * 1    1       1       1       7
712          * ----------------------------------------------------
713          */
714         mux_func -= 1;
715         rza1_set_bit(port, RZA1_PFC_REG, pin, mux_func & MUX_FUNC_PFC_MASK);
716         rza1_set_bit(port, RZA1_PFCE_REG, pin, mux_func & MUX_FUNC_PFCE_MASK);
717         rza1_set_bit(port, RZA1_PFCEA_REG, pin, mux_func & MUX_FUNC_PFCEA_MASK);
718
719         /*
720          * All alternate functions except a few need PIPCn = 1.
721          * If PIPCn has to stay disabled (SW IO mode), configure PMn according
722          * to I/O direction specified by pin configuration -after- PMC has been
723          * set to one.
724          */
725         if (mux_flags & (MUX_FLAGS_SWIO_INPUT | MUX_FLAGS_SWIO_OUTPUT))
726                 rza1_set_bit(port, RZA1_PM_REG, pin,
727                              mux_flags & MUX_FLAGS_SWIO_INPUT);
728         else
729                 rza1_set_bit(port, RZA1_PIPC_REG, pin, 1);
730
731         rza1_set_bit(port, RZA1_PMC_REG, pin, 1);
732
733         return 0;
734 }
735
736 /* ----------------------------------------------------------------------------
737  * gpio operations
738  */
739
740 /**
741  * rza1_gpio_request() - configure pin in port mode
742  *
743  * Configure a pin as gpio (port mode).
744  * After reset, the pin is in input mode with input buffer disabled.
745  * To use the pin as input or output, set_direction shall be called first
746  *
747  * @chip: gpio chip where the gpio sits on
748  * @gpio: gpio offset
749  */
750 static int rza1_gpio_request(struct gpio_chip *chip, unsigned int gpio)
751 {
752         struct rza1_port *port = gpiochip_get_data(chip);
753
754         rza1_pin_reset(port, gpio);
755
756         return 0;
757 }
758
759 /**
760  * rza1_gpio_disable_free() - reset a pin
761  *
762  * Surprisingly, disable_free a gpio, is equivalent to request it.
763  * Reset pin to port mode, with input buffer disabled. This overwrites all
764  * port direction settings applied with set_direction
765  *
766  * @chip: gpio chip where the gpio sits on
767  * @gpio: gpio offset
768  */
769 static void rza1_gpio_free(struct gpio_chip *chip, unsigned int gpio)
770 {
771         struct rza1_port *port = gpiochip_get_data(chip);
772
773         rza1_pin_reset(port, gpio);
774 }
775
776 static int rza1_gpio_get_direction(struct gpio_chip *chip, unsigned int gpio)
777 {
778         struct rza1_port *port = gpiochip_get_data(chip);
779
780         if (rza1_get_bit(port, RZA1_PM_REG, gpio))
781                 return GPIO_LINE_DIRECTION_IN;
782
783         return GPIO_LINE_DIRECTION_OUT;
784 }
785
786 static int rza1_gpio_direction_input(struct gpio_chip *chip,
787                                      unsigned int gpio)
788 {
789         struct rza1_port *port = gpiochip_get_data(chip);
790
791         rza1_pin_set_direction(port, gpio, true);
792
793         return 0;
794 }
795
796 static int rza1_gpio_direction_output(struct gpio_chip *chip,
797                                       unsigned int gpio,
798                                       int value)
799 {
800         struct rza1_port *port = gpiochip_get_data(chip);
801
802         /* Set value before driving pin direction */
803         rza1_pin_set(port, gpio, value);
804         rza1_pin_set_direction(port, gpio, false);
805
806         return 0;
807 }
808
809 /**
810  * rza1_gpio_get() - read a gpio pin value
811  *
812  * Read gpio pin value through PPR register.
813  * Requires bi-directional mode to work when reading the value of a pin
814  * in output mode
815  *
816  * @chip: gpio chip where the gpio sits on
817  * @gpio: gpio offset
818  */
819 static int rza1_gpio_get(struct gpio_chip *chip, unsigned int gpio)
820 {
821         struct rza1_port *port = gpiochip_get_data(chip);
822
823         return rza1_pin_get(port, gpio);
824 }
825
826 static void rza1_gpio_set(struct gpio_chip *chip, unsigned int gpio,
827                           int value)
828 {
829         struct rza1_port *port = gpiochip_get_data(chip);
830
831         rza1_pin_set(port, gpio, value);
832 }
833
834 static const struct gpio_chip rza1_gpiochip_template = {
835         .request                = rza1_gpio_request,
836         .free                   = rza1_gpio_free,
837         .get_direction          = rza1_gpio_get_direction,
838         .direction_input        = rza1_gpio_direction_input,
839         .direction_output       = rza1_gpio_direction_output,
840         .get                    = rza1_gpio_get,
841         .set                    = rza1_gpio_set,
842 };
843 /* ----------------------------------------------------------------------------
844  * pinctrl operations
845  */
846
847 /**
848  * rza1_dt_node_pin_count() - Count number of pins in a dt node or in all its
849  *                            children sub-nodes
850  *
851  * @np: device tree node to parse
852  */
853 static int rza1_dt_node_pin_count(struct device_node *np)
854 {
855         struct device_node *child;
856         struct property *of_pins;
857         unsigned int npins;
858
859         of_pins = of_find_property(np, "pinmux", NULL);
860         if (of_pins)
861                 return of_pins->length / sizeof(u32);
862
863         npins = 0;
864         for_each_child_of_node(np, child) {
865                 of_pins = of_find_property(child, "pinmux", NULL);
866                 if (!of_pins) {
867                         of_node_put(child);
868                         return -EINVAL;
869                 }
870
871                 npins += of_pins->length / sizeof(u32);
872         }
873
874         return npins;
875 }
876
877 /**
878  * rza1_parse_pmx_function() - parse a pin mux sub-node
879  *
880  * @rza1_pctl: RZ/A1 pin controller device
881  * @np: of pmx sub-node
882  * @mux_confs: array of pin mux configurations to fill with parsed info
883  * @grpins: array of pin ids to mux
884  */
885 static int rza1_parse_pinmux_node(struct rza1_pinctrl *rza1_pctl,
886                                   struct device_node *np,
887                                   struct rza1_mux_conf *mux_confs,
888                                   unsigned int *grpins)
889 {
890         struct pinctrl_dev *pctldev = rza1_pctl->pctl;
891         char const *prop_name = "pinmux";
892         unsigned long *pin_configs;
893         unsigned int npin_configs;
894         struct property *of_pins;
895         unsigned int npins;
896         u8 pinmux_flags;
897         unsigned int i;
898         int ret;
899
900         of_pins = of_find_property(np, prop_name, NULL);
901         if (!of_pins) {
902                 dev_dbg(rza1_pctl->dev, "Missing %s property\n", prop_name);
903                 return -ENOENT;
904         }
905         npins = of_pins->length / sizeof(u32);
906
907         /*
908          * Collect pin configuration properties: they apply to all pins in
909          * this sub-node
910          */
911         ret = pinconf_generic_parse_dt_config(np, pctldev, &pin_configs,
912                                               &npin_configs);
913         if (ret) {
914                 dev_err(rza1_pctl->dev,
915                         "Unable to parse pin configuration options for %pOFn\n",
916                         np);
917                 return ret;
918         }
919
920         /*
921          * Create a mask with pinmux flags from pin configuration;
922          * very few pins (TIOC[0-4][A|B|C|D] require SWIO direction
923          * specified in device tree.
924          */
925         pinmux_flags = 0;
926         for (i = 0; i < npin_configs && pinmux_flags == 0; i++)
927                 switch (pinconf_to_config_param(pin_configs[i])) {
928                 case PIN_CONFIG_INPUT_ENABLE:
929                         pinmux_flags |= MUX_FLAGS_SWIO_INPUT;
930                         break;
931                 case PIN_CONFIG_OUTPUT: /* for DT backwards compatibility */
932                 case PIN_CONFIG_OUTPUT_ENABLE:
933                         pinmux_flags |= MUX_FLAGS_SWIO_OUTPUT;
934                 default:
935                         break;
936
937                 }
938
939         kfree(pin_configs);
940
941         /* Collect pin positions and their mux settings. */
942         for (i = 0; i < npins; ++i) {
943                 u32 of_pinconf;
944                 struct rza1_mux_conf *mux_conf = &mux_confs[i];
945
946                 ret = of_property_read_u32_index(np, prop_name, i, &of_pinconf);
947                 if (ret)
948                         return ret;
949
950                 mux_conf->id            = of_pinconf & MUX_PIN_ID_MASK;
951                 mux_conf->port          = RZA1_PIN_ID_TO_PORT(mux_conf->id);
952                 mux_conf->pin           = RZA1_PIN_ID_TO_PIN(mux_conf->id);
953                 mux_conf->mux_func      = MUX_FUNC(of_pinconf);
954                 mux_conf->mux_flags     = pinmux_flags;
955
956                 if (mux_conf->port >= RZA1_NPORTS ||
957                     mux_conf->pin >= RZA1_PINS_PER_PORT) {
958                         dev_err(rza1_pctl->dev,
959                                 "Wrong port %u pin %u for %s property\n",
960                                 mux_conf->port, mux_conf->pin, prop_name);
961                         return -EINVAL;
962                 }
963
964                 grpins[i] = mux_conf->id;
965         }
966
967         return npins;
968 }
969
970 /**
971  * rza1_dt_node_to_map() - map a pin mux node to a function/group
972  *
973  * Parse and register a pin mux function.
974  *
975  * @pctldev: pin controller device
976  * @np: device tree node to parse
977  * @map: pointer to pin map (output)
978  * @num_maps: number of collected maps (output)
979  */
980 static int rza1_dt_node_to_map(struct pinctrl_dev *pctldev,
981                                struct device_node *np,
982                                struct pinctrl_map **map,
983                                unsigned int *num_maps)
984 {
985         struct rza1_pinctrl *rza1_pctl = pinctrl_dev_get_drvdata(pctldev);
986         struct rza1_mux_conf *mux_confs, *mux_conf;
987         unsigned int *grpins, *grpin;
988         struct device_node *child;
989         const char *grpname;
990         const char **fngrps;
991         int ret, npins;
992         int gsel, fsel;
993
994         npins = rza1_dt_node_pin_count(np);
995         if (npins < 0) {
996                 dev_err(rza1_pctl->dev, "invalid pinmux node structure\n");
997                 return -EINVAL;
998         }
999
1000         /*
1001          * Functions are made of 1 group only;
1002          * in fact, functions and groups are identical for this pin controller
1003          * except that functions carry an array of per-pin mux configuration
1004          * settings.
1005          */
1006         mux_confs = devm_kcalloc(rza1_pctl->dev, npins, sizeof(*mux_confs),
1007                                  GFP_KERNEL);
1008         grpins = devm_kcalloc(rza1_pctl->dev, npins, sizeof(*grpins),
1009                               GFP_KERNEL);
1010         fngrps = devm_kzalloc(rza1_pctl->dev, sizeof(*fngrps), GFP_KERNEL);
1011
1012         if (!mux_confs || !grpins || !fngrps)
1013                 return -ENOMEM;
1014
1015         /*
1016          * Parse the pinmux node.
1017          * If the node does not contain "pinmux" property (-ENOENT)
1018          * that property shall be specified in all its children sub-nodes.
1019          */
1020         mux_conf = &mux_confs[0];
1021         grpin = &grpins[0];
1022
1023         ret = rza1_parse_pinmux_node(rza1_pctl, np, mux_conf, grpin);
1024         if (ret == -ENOENT)
1025                 for_each_child_of_node(np, child) {
1026                         ret = rza1_parse_pinmux_node(rza1_pctl, child, mux_conf,
1027                                                      grpin);
1028                         if (ret < 0) {
1029                                 of_node_put(child);
1030                                 return ret;
1031                         }
1032
1033                         grpin += ret;
1034                         mux_conf += ret;
1035                 }
1036         else if (ret < 0)
1037                 return ret;
1038
1039         /* Register pin group and function name to pinctrl_generic */
1040         grpname = np->name;
1041         fngrps[0] = grpname;
1042
1043         mutex_lock(&rza1_pctl->mutex);
1044         gsel = pinctrl_generic_add_group(pctldev, grpname, grpins, npins,
1045                                          NULL);
1046         if (gsel < 0) {
1047                 mutex_unlock(&rza1_pctl->mutex);
1048                 return gsel;
1049         }
1050
1051         fsel = pinmux_generic_add_function(pctldev, grpname, fngrps, 1,
1052                                            mux_confs);
1053         if (fsel < 0) {
1054                 ret = fsel;
1055                 goto remove_group;
1056         }
1057
1058         dev_info(rza1_pctl->dev, "Parsed function and group %s with %d pins\n",
1059                                  grpname, npins);
1060
1061         /* Create map where to retrieve function and mux settings from */
1062         *num_maps = 0;
1063         *map = kzalloc(sizeof(**map), GFP_KERNEL);
1064         if (!*map) {
1065                 ret = -ENOMEM;
1066                 goto remove_function;
1067         }
1068
1069         (*map)->type = PIN_MAP_TYPE_MUX_GROUP;
1070         (*map)->data.mux.group = np->name;
1071         (*map)->data.mux.function = np->name;
1072         *num_maps = 1;
1073         mutex_unlock(&rza1_pctl->mutex);
1074
1075         return 0;
1076
1077 remove_function:
1078         pinmux_generic_remove_function(pctldev, fsel);
1079
1080 remove_group:
1081         pinctrl_generic_remove_group(pctldev, gsel);
1082         mutex_unlock(&rza1_pctl->mutex);
1083
1084         dev_info(rza1_pctl->dev, "Unable to parse function and group %s\n",
1085                                  grpname);
1086
1087         return ret;
1088 }
1089
1090 static void rza1_dt_free_map(struct pinctrl_dev *pctldev,
1091                              struct pinctrl_map *map, unsigned int num_maps)
1092 {
1093         kfree(map);
1094 }
1095
1096 static const struct pinctrl_ops rza1_pinctrl_ops = {
1097         .get_groups_count       = pinctrl_generic_get_group_count,
1098         .get_group_name         = pinctrl_generic_get_group_name,
1099         .get_group_pins         = pinctrl_generic_get_group_pins,
1100         .dt_node_to_map         = rza1_dt_node_to_map,
1101         .dt_free_map            = rza1_dt_free_map,
1102 };
1103
1104 /* ----------------------------------------------------------------------------
1105  * pinmux operations
1106  */
1107
1108 /**
1109  * rza1_set_mux() - retrieve pins from a group and apply their mux settings
1110  *
1111  * @pctldev: pin controller device
1112  * @selector: function selector
1113  * @group: group selector
1114  */
1115 static int rza1_set_mux(struct pinctrl_dev *pctldev, unsigned int selector,
1116                            unsigned int group)
1117 {
1118         struct rza1_pinctrl *rza1_pctl = pinctrl_dev_get_drvdata(pctldev);
1119         struct rza1_mux_conf *mux_confs;
1120         struct function_desc *func;
1121         struct group_desc *grp;
1122         int i;
1123
1124         grp = pinctrl_generic_get_group(pctldev, group);
1125         if (!grp)
1126                 return -EINVAL;
1127
1128         func = pinmux_generic_get_function(pctldev, selector);
1129         if (!func)
1130                 return -EINVAL;
1131
1132         mux_confs = (struct rza1_mux_conf *)func->data;
1133         for (i = 0; i < grp->num_pins; ++i) {
1134                 int ret;
1135
1136                 ret = rza1_pin_mux_single(rza1_pctl, &mux_confs[i]);
1137                 if (ret)
1138                         return ret;
1139         }
1140
1141         return 0;
1142 }
1143
1144 static const struct pinmux_ops rza1_pinmux_ops = {
1145         .get_functions_count    = pinmux_generic_get_function_count,
1146         .get_function_name      = pinmux_generic_get_function_name,
1147         .get_function_groups    = pinmux_generic_get_function_groups,
1148         .set_mux                = rza1_set_mux,
1149         .strict                 = true,
1150 };
1151
1152 /* ----------------------------------------------------------------------------
1153  * RZ/A1 pin controller driver operations
1154  */
1155
1156 static unsigned int rza1_count_gpio_chips(struct device_node *np)
1157 {
1158         struct device_node *child;
1159         unsigned int count = 0;
1160
1161         for_each_child_of_node(np, child) {
1162                 if (!of_property_read_bool(child, "gpio-controller"))
1163                         continue;
1164
1165                 count++;
1166         }
1167
1168         return count;
1169 }
1170
1171 /**
1172  * rza1_parse_gpiochip() - parse and register a gpio chip and pin range
1173  *
1174  * The gpio controller subnode shall provide a "gpio-ranges" list property as
1175  * defined by gpio device tree binding documentation.
1176  *
1177  * @rza1_pctl: RZ/A1 pin controller device
1178  * @np: of gpio-controller node
1179  * @chip: gpio chip to register to gpiolib
1180  * @range: pin range to register to pinctrl core
1181  */
1182 static int rza1_parse_gpiochip(struct rza1_pinctrl *rza1_pctl,
1183                                struct device_node *np,
1184                                struct gpio_chip *chip,
1185                                struct pinctrl_gpio_range *range)
1186 {
1187         const char *list_name = "gpio-ranges";
1188         struct of_phandle_args of_args;
1189         unsigned int gpioport;
1190         u32 pinctrl_base;
1191         int ret;
1192
1193         ret = of_parse_phandle_with_fixed_args(np, list_name, 3, 0, &of_args);
1194         if (ret) {
1195                 dev_err(rza1_pctl->dev, "Unable to parse %s list property\n",
1196                         list_name);
1197                 return ret;
1198         }
1199
1200         /*
1201          * Find out on which port this gpio-chip maps to by inspecting the
1202          * second argument of the "gpio-ranges" property.
1203          */
1204         pinctrl_base = of_args.args[1];
1205         gpioport = RZA1_PIN_ID_TO_PORT(pinctrl_base);
1206         if (gpioport >= RZA1_NPORTS) {
1207                 dev_err(rza1_pctl->dev,
1208                         "Invalid values in property %s\n", list_name);
1209                 return -EINVAL;
1210         }
1211
1212         *chip           = rza1_gpiochip_template;
1213         chip->base      = -1;
1214         chip->label     = devm_kasprintf(rza1_pctl->dev, GFP_KERNEL, "%pOFn",
1215                                          np);
1216         if (!chip->label)
1217                 return -ENOMEM;
1218
1219         chip->ngpio     = of_args.args[2];
1220         chip->of_node   = np;
1221         chip->parent    = rza1_pctl->dev;
1222
1223         range->id       = gpioport;
1224         range->name     = chip->label;
1225         range->pin_base = range->base = pinctrl_base;
1226         range->npins    = of_args.args[2];
1227         range->gc       = chip;
1228
1229         ret = devm_gpiochip_add_data(rza1_pctl->dev, chip,
1230                                      &rza1_pctl->ports[gpioport]);
1231         if (ret)
1232                 return ret;
1233
1234         pinctrl_add_gpio_range(rza1_pctl->pctl, range);
1235
1236         dev_dbg(rza1_pctl->dev, "Parsed gpiochip %s with %d pins\n",
1237                 chip->label, chip->ngpio);
1238
1239         return 0;
1240 }
1241
1242 /**
1243  * rza1_gpio_register() - parse DT to collect gpio-chips and gpio-ranges
1244  *
1245  * @rza1_pctl: RZ/A1 pin controller device
1246  */
1247 static int rza1_gpio_register(struct rza1_pinctrl *rza1_pctl)
1248 {
1249         struct device_node *np = rza1_pctl->dev->of_node;
1250         struct pinctrl_gpio_range *gpio_ranges;
1251         struct gpio_chip *gpio_chips;
1252         struct device_node *child;
1253         unsigned int ngpiochips;
1254         unsigned int i;
1255         int ret;
1256
1257         ngpiochips = rza1_count_gpio_chips(np);
1258         if (ngpiochips == 0) {
1259                 dev_dbg(rza1_pctl->dev, "No gpiochip registered\n");
1260                 return 0;
1261         }
1262
1263         gpio_chips = devm_kcalloc(rza1_pctl->dev, ngpiochips,
1264                                   sizeof(*gpio_chips), GFP_KERNEL);
1265         gpio_ranges = devm_kcalloc(rza1_pctl->dev, ngpiochips,
1266                                    sizeof(*gpio_ranges), GFP_KERNEL);
1267         if (!gpio_chips || !gpio_ranges)
1268                 return -ENOMEM;
1269
1270         i = 0;
1271         for_each_child_of_node(np, child) {
1272                 if (!of_property_read_bool(child, "gpio-controller"))
1273                         continue;
1274
1275                 ret = rza1_parse_gpiochip(rza1_pctl, child, &gpio_chips[i],
1276                                           &gpio_ranges[i]);
1277                 if (ret) {
1278                         of_node_put(child);
1279                         return ret;
1280                 }
1281
1282                 ++i;
1283         }
1284
1285         dev_info(rza1_pctl->dev, "Registered %u gpio controllers\n", i);
1286
1287         return 0;
1288 }
1289
1290 /**
1291  * rza1_pinctrl_register() - Enumerate pins, ports and gpiochips; register
1292  *                           them to pinctrl and gpio cores.
1293  *
1294  * @rza1_pctl: RZ/A1 pin controller device
1295  */
1296 static int rza1_pinctrl_register(struct rza1_pinctrl *rza1_pctl)
1297 {
1298         struct pinctrl_pin_desc *pins;
1299         struct rza1_port *ports;
1300         unsigned int i;
1301         int ret;
1302
1303         pins = devm_kcalloc(rza1_pctl->dev, RZA1_NPINS, sizeof(*pins),
1304                             GFP_KERNEL);
1305         ports = devm_kcalloc(rza1_pctl->dev, RZA1_NPORTS, sizeof(*ports),
1306                              GFP_KERNEL);
1307         if (!pins || !ports)
1308                 return -ENOMEM;
1309
1310         rza1_pctl->pins         = pins;
1311         rza1_pctl->desc.pins    = pins;
1312         rza1_pctl->desc.npins   = RZA1_NPINS;
1313         rza1_pctl->ports        = ports;
1314
1315         for (i = 0; i < RZA1_NPINS; ++i) {
1316                 unsigned int pin = RZA1_PIN_ID_TO_PIN(i);
1317                 unsigned int port = RZA1_PIN_ID_TO_PORT(i);
1318
1319                 pins[i].number = i;
1320                 pins[i].name = devm_kasprintf(rza1_pctl->dev, GFP_KERNEL,
1321                                               "P%u-%u", port, pin);
1322                 if (!pins[i].name)
1323                         return -ENOMEM;
1324
1325                 if (i % RZA1_PINS_PER_PORT == 0) {
1326                         /*
1327                          * Setup ports;
1328                          * they provide per-port lock and logical base address.
1329                          */
1330                         unsigned int port_id = RZA1_PIN_ID_TO_PORT(i);
1331
1332                         ports[port_id].id       = port_id;
1333                         ports[port_id].base     = rza1_pctl->base;
1334                         ports[port_id].pins     = &pins[i];
1335                         spin_lock_init(&ports[port_id].lock);
1336                 }
1337         }
1338
1339         ret = devm_pinctrl_register_and_init(rza1_pctl->dev, &rza1_pctl->desc,
1340                                              rza1_pctl, &rza1_pctl->pctl);
1341         if (ret) {
1342                 dev_err(rza1_pctl->dev,
1343                         "RZ/A1 pin controller registration failed\n");
1344                 return ret;
1345         }
1346
1347         ret = pinctrl_enable(rza1_pctl->pctl);
1348         if (ret) {
1349                 dev_err(rza1_pctl->dev,
1350                         "RZ/A1 pin controller failed to start\n");
1351                 return ret;
1352         }
1353
1354         ret = rza1_gpio_register(rza1_pctl);
1355         if (ret) {
1356                 dev_err(rza1_pctl->dev, "RZ/A1 GPIO registration failed\n");
1357                 return ret;
1358         }
1359
1360         return 0;
1361 }
1362
1363 static int rza1_pinctrl_probe(struct platform_device *pdev)
1364 {
1365         struct rza1_pinctrl *rza1_pctl;
1366         int ret;
1367
1368         rza1_pctl = devm_kzalloc(&pdev->dev, sizeof(*rza1_pctl), GFP_KERNEL);
1369         if (!rza1_pctl)
1370                 return -ENOMEM;
1371
1372         rza1_pctl->dev = &pdev->dev;
1373
1374         rza1_pctl->base = devm_platform_ioremap_resource(pdev, 0);
1375         if (IS_ERR(rza1_pctl->base))
1376                 return PTR_ERR(rza1_pctl->base);
1377
1378         mutex_init(&rza1_pctl->mutex);
1379
1380         platform_set_drvdata(pdev, rza1_pctl);
1381
1382         rza1_pctl->desc.name    = DRIVER_NAME;
1383         rza1_pctl->desc.pctlops = &rza1_pinctrl_ops;
1384         rza1_pctl->desc.pmxops  = &rza1_pinmux_ops;
1385         rza1_pctl->desc.owner   = THIS_MODULE;
1386         rza1_pctl->data         = of_device_get_match_data(&pdev->dev);
1387
1388         ret = rza1_pinctrl_register(rza1_pctl);
1389         if (ret)
1390                 return ret;
1391
1392         dev_info(&pdev->dev,
1393                  "RZ/A1 pin controller and gpio successfully registered\n");
1394
1395         return 0;
1396 }
1397
1398 static const struct of_device_id rza1_pinctrl_of_match[] = {
1399         {
1400                 /* RZ/A1H, RZ/A1M */
1401                 .compatible     = "renesas,r7s72100-ports",
1402                 .data           = &rza1h_pmx_conf,
1403         },
1404         {
1405                 /* RZ/A1L */
1406                 .compatible     = "renesas,r7s72102-ports",
1407                 .data           = &rza1l_pmx_conf,
1408         },
1409         { }
1410 };
1411
1412 static struct platform_driver rza1_pinctrl_driver = {
1413         .driver = {
1414                 .name = DRIVER_NAME,
1415                 .of_match_table = rza1_pinctrl_of_match,
1416         },
1417         .probe = rza1_pinctrl_probe,
1418 };
1419
1420 static int __init rza1_pinctrl_init(void)
1421 {
1422         return platform_driver_register(&rza1_pinctrl_driver);
1423 }
1424 core_initcall(rza1_pinctrl_init);
1425
1426 MODULE_AUTHOR("Jacopo Mondi <jacopo+renesas@jmondi.org");
1427 MODULE_DESCRIPTION("Pin and gpio controller driver for Reneas RZ/A1 SoC");
1428 MODULE_LICENSE("GPL v2");