drivers/nvmem/imx-ocotp.c

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * i.MX6 OCOTP fusebox driver
   4  *
   5  * Copyright (c) 2015 Pengutronix, Philipp Zabel <p.zabel@pengutronix.de>
   6  *
   7  * Copyright 2019 NXP
   8  *
   9  * Based on the barebox ocotp driver,
  10  * Copyright (c) 2010 Baruch Siach <baruch@tkos.co.il>,
  11  *      Orex Computed Radiography
  12  *
  13  * Write support based on the fsl_otp driver,
  14  * Copyright (C) 2010-2013 Freescale Semiconductor, Inc
  15  */
  16
  17 #include <linux/clk.h>
  18 #include <linux/device.h>
  19 #include <linux/io.h>
  20 #include <linux/module.h>
  21 #include <linux/nvmem-provider.h>
  22 #include <linux/of.h>
  23 #include <linux/of_device.h>
  24 #include <linux/platform_device.h>
  25 #include <linux/slab.h>
  26 #include <linux/delay.h>
  27
  28 #define IMX_OCOTP_OFFSET_B0W0           0x400 /* Offset from base address of the
  29                                                * OTP Bank0 Word0
  30                                                */
  31 #define IMX_OCOTP_OFFSET_PER_WORD       0x10  /* Offset between the start addr
  32                                                * of two consecutive OTP words.
  33                                                */
  34
  35 #define IMX_OCOTP_ADDR_CTRL             0x0000
  36 #define IMX_OCOTP_ADDR_CTRL_SET         0x0004
  37 #define IMX_OCOTP_ADDR_CTRL_CLR         0x0008
  38 #define IMX_OCOTP_ADDR_TIMING           0x0010
  39 #define IMX_OCOTP_ADDR_DATA0            0x0020
  40 #define IMX_OCOTP_ADDR_DATA1            0x0030
  41 #define IMX_OCOTP_ADDR_DATA2            0x0040
  42 #define IMX_OCOTP_ADDR_DATA3            0x0050
  43
  44 #define IMX_OCOTP_BM_CTRL_ADDR          0x000000FF
  45 #define IMX_OCOTP_BM_CTRL_BUSY          0x00000100
  46 #define IMX_OCOTP_BM_CTRL_ERROR         0x00000200
  47 #define IMX_OCOTP_BM_CTRL_REL_SHADOWS   0x00000400
  48
  49 #define IMX_OCOTP_BM_CTRL_ADDR_8MP              0x000001FF
  50 #define IMX_OCOTP_BM_CTRL_BUSY_8MP              0x00000200
  51 #define IMX_OCOTP_BM_CTRL_ERROR_8MP             0x00000400
  52 #define IMX_OCOTP_BM_CTRL_REL_SHADOWS_8MP       0x00000800
  53
  54 #define IMX_OCOTP_BM_CTRL_DEFAULT                               \
  55         {                                                       \
  56                 .bm_addr = IMX_OCOTP_BM_CTRL_ADDR,              \
  57                 .bm_busy = IMX_OCOTP_BM_CTRL_BUSY,              \
  58                 .bm_error = IMX_OCOTP_BM_CTRL_ERROR,            \
  59                 .bm_rel_shadows = IMX_OCOTP_BM_CTRL_REL_SHADOWS,\
  60         }
  61
  62 #define IMX_OCOTP_BM_CTRL_8MP                                   \
  63         {                                                       \
  64                 .bm_addr = IMX_OCOTP_BM_CTRL_ADDR_8MP,          \
  65                 .bm_busy = IMX_OCOTP_BM_CTRL_BUSY_8MP,          \
  66                 .bm_error = IMX_OCOTP_BM_CTRL_ERROR_8MP,        \
  67                 .bm_rel_shadows = IMX_OCOTP_BM_CTRL_REL_SHADOWS_8MP,\
  68         }
  69
  70 #define TIMING_STROBE_PROG_US           10      /* Min time to blow a fuse */
  71 #define TIMING_STROBE_READ_NS           37      /* Min time before read */
  72 #define TIMING_RELAX_NS                 17
  73 #define DEF_FSOURCE                     1001    /* > 1000 ns */
  74 #define DEF_STROBE_PROG                 10000   /* IPG clocks */
  75 #define IMX_OCOTP_WR_UNLOCK             0x3E770000
  76 #define IMX_OCOTP_READ_LOCKED_VAL       0xBADABADA
  77
  78 static DEFINE_MUTEX(ocotp_mutex);
  79
  80 struct ocotp_priv {
  81         struct device *dev;
  82         struct clk *clk;
  83         void __iomem *base;
  84         const struct ocotp_params *params;
  85         struct nvmem_config *config;
  86 };
  87
  88 struct ocotp_ctrl_reg {
  89         u32 bm_addr;
  90         u32 bm_busy;
  91         u32 bm_error;
  92         u32 bm_rel_shadows;
  93 };
  94
  95 struct ocotp_params {
  96         unsigned int nregs;
  97         unsigned int bank_address_words;
  98         void (*set_timing)(struct ocotp_priv *priv);
  99         struct ocotp_ctrl_reg ctrl;
 100 };
 101
 102 static int imx_ocotp_wait_for_busy(struct ocotp_priv *priv, u32 flags)
 103 {
 104         int count;
 105         u32 c, mask;
 106         u32 bm_ctrl_busy, bm_ctrl_error;
 107         void __iomem *base = priv->base;
 108
 109         bm_ctrl_busy = priv->params->ctrl.bm_busy;
 110         bm_ctrl_error = priv->params->ctrl.bm_error;
 111
 112         mask = bm_ctrl_busy | bm_ctrl_error | flags;
 113
 114         for (count = 10000; count >= 0; count--) {
 115                 c = readl(base + IMX_OCOTP_ADDR_CTRL);
 116                 if (!(c & mask))
 117                         break;
 118                 cpu_relax();
 119         }
 120
 121         if (count < 0) {
 122                 /* HW_OCOTP_CTRL[ERROR] will be set under the following
 123                  * conditions:
 124                  * - A write is performed to a shadow register during a shadow
 125                  *   reload (essentially, while HW_OCOTP_CTRL[RELOAD_SHADOWS] is
 126                  *   set. In addition, the contents of the shadow register shall
 127                  *   not be updated.
 128                  * - A write is performed to a shadow register which has been
 129                  *   locked.
 130                  * - A read is performed to from a shadow register which has
 131                  *   been read locked.
 132                  * - A program is performed to a fuse word which has been locked
 133                  * - A read is performed to from a fuse word which has been read
 134                  *   locked.
 135                  */
 136                 if (c & bm_ctrl_error)
 137                         return -EPERM;
 138                 return -ETIMEDOUT;
 139         }
 140
 141         return 0;
 142 }
 143
 144 static void imx_ocotp_clr_err_if_set(struct ocotp_priv *priv)
 145 {
 146         u32 c, bm_ctrl_error;
 147         void __iomem *base = priv->base;
 148
 149         bm_ctrl_error = priv->params->ctrl.bm_error;
 150
 151         c = readl(base + IMX_OCOTP_ADDR_CTRL);
 152         if (!(c & bm_ctrl_error))
 153                 return;
 154
 155         writel(bm_ctrl_error, base + IMX_OCOTP_ADDR_CTRL_CLR);
 156 }
 157
 158 static int imx_ocotp_read(void *context, unsigned int offset,
 159                           void *val, size_t bytes)
 160 {
 161         struct ocotp_priv *priv = context;
 162         unsigned int count;
 163         u8 *buf, *p;
 164         int i, ret;
 165         u32 index, num_bytes;
 166
 167         index = offset >> 2;
 168         num_bytes = round_up((offset % 4) + bytes, 4);
 169         count = num_bytes >> 2;
 170
 171         if (count > (priv->params->nregs - index))
 172                 count = priv->params->nregs - index;
 173
 174         p = kzalloc(num_bytes, GFP_KERNEL);
 175         if (!p)
 176                 return -ENOMEM;
 177
 178         mutex_lock(&ocotp_mutex);
 179
 180         buf = p;
 181
 182         ret = clk_prepare_enable(priv->clk);
 183         if (ret < 0) {
 184                 mutex_unlock(&ocotp_mutex);
 185                 dev_err(priv->dev, "failed to prepare/enable ocotp clk\n");
 186                 kfree(p);
 187                 return ret;
 188         }
 189
 190         ret = imx_ocotp_wait_for_busy(priv, 0);
 191         if (ret < 0) {
 192                 dev_err(priv->dev, "timeout during read setup\n");
 193                 goto read_end;
 194         }
 195
 196         for (i = index; i < (index + count); i++) {
 197                 *(u32 *)buf = readl(priv->base + IMX_OCOTP_OFFSET_B0W0 +
 198                                i * IMX_OCOTP_OFFSET_PER_WORD);
 199
 200                 /* 47.3.1.2
 201                  * For "read locked" registers 0xBADABADA will be returned and
 202                  * HW_OCOTP_CTRL[ERROR] will be set. It must be cleared by
 203                  * software before any new write, read or reload access can be
 204                  * issued
 205                  */
 206                 if (*((u32 *)buf) == IMX_OCOTP_READ_LOCKED_VAL)
 207                         imx_ocotp_clr_err_if_set(priv);
 208
 209                 buf += 4;
 210         }
 211
 212         index = offset % 4;
 213         memcpy(val, &p[index], bytes);
 214
 215 read_end:
 216         clk_disable_unprepare(priv->clk);
 217         mutex_unlock(&ocotp_mutex);
 218
 219         kfree(p);
 220
 221         return ret;
 222 }
 223
 224 static int imx_ocotp_cell_pp(void *context, const char *id, int index,
 225                              unsigned int offset, void *data, size_t bytes)
 226 {
 227         u8 *buf = data;
 228         int i;
 229
 230         /* Deal with some post processing of nvmem cell data */
 231         if (id && !strcmp(id, "mac-address"))
 232                 for (i = 0; i < bytes / 2; i++)
 233                         swap(buf[i], buf[bytes - i - 1]);
 234
 235         return 0;
 236 }
 237
 238 static void imx_ocotp_set_imx6_timing(struct ocotp_priv *priv)
 239 {
 240         unsigned long clk_rate;
 241         unsigned long strobe_read, relax, strobe_prog;
 242         u32 timing;
 243
 244         /* 47.3.1.3.1
 245          * Program HW_OCOTP_TIMING[STROBE_PROG] and HW_OCOTP_TIMING[RELAX]
 246          * fields with timing values to match the current frequency of the
 247          * ipg_clk. OTP writes will work at maximum bus frequencies as long
 248          * as the HW_OCOTP_TIMING parameters are set correctly.
 249          *
 250          * Note: there are minimum timings required to ensure an OTP fuse burns
 251          * correctly that are independent of the ipg_clk. Those values are not
 252          * formally documented anywhere however, working from the minimum
 253          * timings given in u-boot we can say:
 254          *
 255          * - Minimum STROBE_PROG time is 10 microseconds. Intuitively 10
 256          *   microseconds feels about right as representative of a minimum time
 257          *   to physically burn out a fuse.
 258          *
 259          * - Minimum STROBE_READ i.e. the time to wait post OTP fuse burn before
 260          *   performing another read is 37 nanoseconds
 261          *
 262          * - Minimum RELAX timing is 17 nanoseconds. This final RELAX minimum
 263          *   timing is not entirely clear the documentation says "This
 264          *   count value specifies the time to add to all default timing
 265          *   parameters other than the Tpgm and Trd. It is given in number
 266          *   of ipg_clk periods." where Tpgm and Trd refer to STROBE_PROG
 267          *   and STROBE_READ respectively. What the other timing parameters
 268          *   are though, is not specified. Experience shows a zero RELAX
 269          *   value will mess up a re-load of the shadow registers post OTP
 270          *   burn.
 271          */
 272         clk_rate = clk_get_rate(priv->clk);
 273
 274         relax = DIV_ROUND_UP(clk_rate * TIMING_RELAX_NS, 1000000000) - 1;
 275         strobe_read = DIV_ROUND_UP(clk_rate * TIMING_STROBE_READ_NS,
 276                                    1000000000);
 277         strobe_read += 2 * (relax + 1) - 1;
 278         strobe_prog = DIV_ROUND_CLOSEST(clk_rate * TIMING_STROBE_PROG_US,
 279                                         1000000);
 280         strobe_prog += 2 * (relax + 1) - 1;
 281
 282         timing = readl(priv->base + IMX_OCOTP_ADDR_TIMING) & 0x0FC00000;
 283         timing |= strobe_prog & 0x00000FFF;
 284         timing |= (relax       << 12) & 0x0000F000;
 285         timing |= (strobe_read << 16) & 0x003F0000;
 286
 287         writel(timing, priv->base + IMX_OCOTP_ADDR_TIMING);
 288 }
 289
 290 static void imx_ocotp_set_imx7_timing(struct ocotp_priv *priv)
 291 {
 292         unsigned long clk_rate;
 293         u64 fsource, strobe_prog;
 294         u32 timing;
 295
 296         /* i.MX 7Solo Applications Processor Reference Manual, Rev. 0.1
 297          * 6.4.3.3
 298          */
 299         clk_rate = clk_get_rate(priv->clk);
 300         fsource = DIV_ROUND_UP_ULL((u64)clk_rate * DEF_FSOURCE,
 301                                    NSEC_PER_SEC) + 1;
 302         strobe_prog = DIV_ROUND_CLOSEST_ULL((u64)clk_rate * DEF_STROBE_PROG,
 303                                             NSEC_PER_SEC) + 1;
 304
 305         timing = strobe_prog & 0x00000FFF;
 306         timing |= (fsource << 12) & 0x000FF000;
 307
 308         writel(timing, priv->base + IMX_OCOTP_ADDR_TIMING);
 309 }
 310
 311 static int imx_ocotp_write(void *context, unsigned int offset, void *val,
 312                            size_t bytes)
 313 {
 314         struct ocotp_priv *priv = context;
 315         u32 *buf = val;
 316         int ret;
 317
 318         u32 ctrl;
 319         u8 waddr;
 320         u8 word = 0;
 321
 322         /* allow only writing one complete OTP word at a time */
 323         if ((bytes != priv->config->word_size) ||
 324             (offset % priv->config->word_size))
 325                 return -EINVAL;
 326
 327         mutex_lock(&ocotp_mutex);
 328
 329         ret = clk_prepare_enable(priv->clk);
 330         if (ret < 0) {
 331                 mutex_unlock(&ocotp_mutex);
 332                 dev_err(priv->dev, "failed to prepare/enable ocotp clk\n");
 333                 return ret;
 334         }
 335
 336         /* Setup the write timing values */
 337         priv->params->set_timing(priv);
 338
 339         /* 47.3.1.3.2
 340          * Check that HW_OCOTP_CTRL[BUSY] and HW_OCOTP_CTRL[ERROR] are clear.
 341          * Overlapped accesses are not supported by the controller. Any pending
 342          * write or reload must be completed before a write access can be
 343          * requested.
 344          */
 345         ret = imx_ocotp_wait_for_busy(priv, 0);
 346         if (ret < 0) {
 347                 dev_err(priv->dev, "timeout during timing setup\n");
 348                 goto write_end;
 349         }
 350
 351         /* 47.3.1.3.3
 352          * Write the requested address to HW_OCOTP_CTRL[ADDR] and program the
 353          * unlock code into HW_OCOTP_CTRL[WR_UNLOCK]. This must be programmed
 354          * for each write access. The lock code is documented in the register
 355          * description. Both the unlock code and address can be written in the
 356          * same operation.
 357          */
 358         if (priv->params->bank_address_words != 0) {
 359                 /*
 360                  * In banked/i.MX7 mode the OTP register bank goes into waddr
 361                  * see i.MX 7Solo Applications Processor Reference Manual, Rev.
 362                  * 0.1 section 6.4.3.1
 363                  */
 364                 offset = offset / priv->config->word_size;
 365                 waddr = offset / priv->params->bank_address_words;
 366                 word  = offset & (priv->params->bank_address_words - 1);
 367         } else {
 368                 /*
 369                  * Non-banked i.MX6 mode.
 370                  * OTP write/read address specifies one of 128 word address
 371                  * locations
 372                  */
 373                 waddr = offset / 4;
 374         }
 375
 376         ctrl = readl(priv->base + IMX_OCOTP_ADDR_CTRL);
 377         ctrl &= ~priv->params->ctrl.bm_addr;
 378         ctrl |= waddr & priv->params->ctrl.bm_addr;
 379         ctrl |= IMX_OCOTP_WR_UNLOCK;
 380
 381         writel(ctrl, priv->base + IMX_OCOTP_ADDR_CTRL);
 382
 383         /* 47.3.1.3.4
 384          * Write the data to the HW_OCOTP_DATA register. This will automatically
 385          * set HW_OCOTP_CTRL[BUSY] and clear HW_OCOTP_CTRL[WR_UNLOCK]. To
 386          * protect programming same OTP bit twice, before program OCOTP will
 387          * automatically read fuse value in OTP and use read value to mask
 388          * program data. The controller will use masked program data to program
 389          * a 32-bit word in the OTP per the address in HW_OCOTP_CTRL[ADDR]. Bit
 390          * fields with 1's will result in that OTP bit being programmed. Bit
 391          * fields with 0's will be ignored. At the same time that the write is
 392          * accepted, the controller makes an internal copy of
 393          * HW_OCOTP_CTRL[ADDR] which cannot be updated until the next write
 394          * sequence is initiated. This copy guarantees that erroneous writes to
 395          * HW_OCOTP_CTRL[ADDR] will not affect an active write operation. It
 396          * should also be noted that during the programming HW_OCOTP_DATA will
 397          * shift right (with zero fill). This shifting is required to program
 398          * the OTP serially. During the write operation, HW_OCOTP_DATA cannot be
 399          * modified.
 400          * Note: on i.MX7 there are four data fields to write for banked write
 401          *       with the fuse blowing operation only taking place after data0
 402          *       has been written. This is why data0 must always be the last
 403          *       register written.
 404          */
 405         if (priv->params->bank_address_words != 0) {
 406                 /* Banked/i.MX7 mode */
 407                 switch (word) {
 408                 case 0:
 409                         writel(0, priv->base + IMX_OCOTP_ADDR_DATA1);
 410                         writel(0, priv->base + IMX_OCOTP_ADDR_DATA2);
 411                         writel(0, priv->base + IMX_OCOTP_ADDR_DATA3);
 412                         writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA0);
 413                         break;
 414                 case 1:
 415                         writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA1);
 416                         writel(0, priv->base + IMX_OCOTP_ADDR_DATA2);
 417                         writel(0, priv->base + IMX_OCOTP_ADDR_DATA3);
 418                         writel(0, priv->base + IMX_OCOTP_ADDR_DATA0);
 419                         break;
 420                 case 2:
 421                         writel(0, priv->base + IMX_OCOTP_ADDR_DATA1);
 422                         writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA2);
 423                         writel(0, priv->base + IMX_OCOTP_ADDR_DATA3);
 424                         writel(0, priv->base + IMX_OCOTP_ADDR_DATA0);
 425                         break;
 426                 case 3:
 427                         writel(0, priv->base + IMX_OCOTP_ADDR_DATA1);
 428                         writel(0, priv->base + IMX_OCOTP_ADDR_DATA2);
 429                         writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA3);
 430                         writel(0, priv->base + IMX_OCOTP_ADDR_DATA0);
 431                         break;
 432                 }
 433         } else {
 434                 /* Non-banked i.MX6 mode */
 435                 writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA0);
 436         }
 437
 438         /* 47.4.1.4.5
 439          * Once complete, the controller will clear BUSY. A write request to a
 440          * protected or locked region will result in no OTP access and no
 441          * setting of HW_OCOTP_CTRL[BUSY]. In addition HW_OCOTP_CTRL[ERROR] will
 442          * be set. It must be cleared by software before any new write access
 443          * can be issued.
 444          */
 445         ret = imx_ocotp_wait_for_busy(priv, 0);
 446         if (ret < 0) {
 447                 if (ret == -EPERM) {
 448                         dev_err(priv->dev, "failed write to locked region");
 449                         imx_ocotp_clr_err_if_set(priv);
 450                 } else {
 451                         dev_err(priv->dev, "timeout during data write\n");
 452                 }
 453                 goto write_end;
 454         }
 455
 456         /* 47.3.1.4
 457          * Write Postamble: Due to internal electrical characteristics of the
 458          * OTP during writes, all OTP operations following a write must be
 459          * separated by 2 us after the clearing of HW_OCOTP_CTRL_BUSY following
 460          * the write.
 461          */
 462         udelay(2);
 463
 464         /* reload all shadow registers */
 465         writel(priv->params->ctrl.bm_rel_shadows,
 466                priv->base + IMX_OCOTP_ADDR_CTRL_SET);
 467         ret = imx_ocotp_wait_for_busy(priv,
 468                                       priv->params->ctrl.bm_rel_shadows);
 469         if (ret < 0)
 470                 dev_err(priv->dev, "timeout during shadow register reload\n");
 471
 472 write_end:
 473         clk_disable_unprepare(priv->clk);
 474         mutex_unlock(&ocotp_mutex);
 475         return ret < 0 ? ret : bytes;
 476 }
 477
 478 static struct nvmem_config imx_ocotp_nvmem_config = {
 479         .name = "imx-ocotp",
 480         .read_only = false,
 481         .word_size = 4,
 482         .stride = 1,
 483         .reg_read = imx_ocotp_read,
 484         .reg_write = imx_ocotp_write,
 485 };
 486
 487 static const struct ocotp_params imx6q_params = {
 488         .nregs = 128,
 489         .bank_address_words = 0,
 490         .set_timing = imx_ocotp_set_imx6_timing,
 491         .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT,
 492 };
 493
 494 static const struct ocotp_params imx6sl_params = {
 495         .nregs = 64,
 496         .bank_address_words = 0,
 497         .set_timing = imx_ocotp_set_imx6_timing,
 498         .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT,
 499 };
 500
 501 static const struct ocotp_params imx6sll_params = {
 502         .nregs = 128,
 503         .bank_address_words = 0,
 504         .set_timing = imx_ocotp_set_imx6_timing,
 505         .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT,
 506 };
 507
 508 static const struct ocotp_params imx6sx_params = {
 509         .nregs = 128,
 510         .bank_address_words = 0,
 511         .set_timing = imx_ocotp_set_imx6_timing,
 512         .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT,
 513 };
 514
 515 static const struct ocotp_params imx6ul_params = {
 516         .nregs = 128,
 517         .bank_address_words = 0,
 518         .set_timing = imx_ocotp_set_imx6_timing,
 519         .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT,
 520 };
 521
 522 static const struct ocotp_params imx6ull_params = {
 523         .nregs = 64,
 524         .bank_address_words = 0,
 525         .set_timing = imx_ocotp_set_imx6_timing,
 526         .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT,
 527 };
 528
 529 static const struct ocotp_params imx7d_params = {
 530         .nregs = 64,
 531         .bank_address_words = 4,
 532         .set_timing = imx_ocotp_set_imx7_timing,
 533         .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT,
 534 };
 535
 536 static const struct ocotp_params imx7ulp_params = {
 537         .nregs = 256,
 538         .bank_address_words = 0,
 539         .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT,
 540 };
 541
 542 static const struct ocotp_params imx8mq_params = {
 543         .nregs = 256,
 544         .bank_address_words = 0,
 545         .set_timing = imx_ocotp_set_imx6_timing,
 546         .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT,
 547 };
 548
 549 static const struct ocotp_params imx8mm_params = {
 550         .nregs = 256,
 551         .bank_address_words = 0,
 552         .set_timing = imx_ocotp_set_imx6_timing,
 553         .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT,
 554 };
 555
 556 static const struct ocotp_params imx8mn_params = {
 557         .nregs = 256,
 558         .bank_address_words = 0,
 559         .set_timing = imx_ocotp_set_imx6_timing,
 560         .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT,
 561 };
 562
 563 static const struct ocotp_params imx8mp_params = {
 564         .nregs = 384,
 565         .bank_address_words = 0,
 566         .set_timing = imx_ocotp_set_imx6_timing,
 567         .ctrl = IMX_OCOTP_BM_CTRL_8MP,
 568 };
 569
 570 static const struct of_device_id imx_ocotp_dt_ids[] = {
 571         { .compatible = "fsl,imx6q-ocotp",  .data = &imx6q_params },
 572         { .compatible = "fsl,imx6sl-ocotp", .data = &imx6sl_params },
 573         { .compatible = "fsl,imx6sx-ocotp", .data = &imx6sx_params },
 574         { .compatible = "fsl,imx6ul-ocotp", .data = &imx6ul_params },
 575         { .compatible = "fsl,imx6ull-ocotp", .data = &imx6ull_params },
 576         { .compatible = "fsl,imx7d-ocotp",  .data = &imx7d_params },
 577         { .compatible = "fsl,imx6sll-ocotp", .data = &imx6sll_params },
 578         { .compatible = "fsl,imx7ulp-ocotp", .data = &imx7ulp_params },
 579         { .compatible = "fsl,imx8mq-ocotp", .data = &imx8mq_params },
 580         { .compatible = "fsl,imx8mm-ocotp", .data = &imx8mm_params },
 581         { .compatible = "fsl,imx8mn-ocotp", .data = &imx8mn_params },
 582         { .compatible = "fsl,imx8mp-ocotp", .data = &imx8mp_params },
 583         { },
 584 };
 585 MODULE_DEVICE_TABLE(of, imx_ocotp_dt_ids);
 586
 587 static void imx_ocotp_fixup_cell_info(struct nvmem_device *nvmem,
 588                                       struct nvmem_layout *layout,
 589                                       struct nvmem_cell_info *cell)
 590 {
 591         cell->read_post_process = imx_ocotp_cell_pp;
 592 }
 593
 594 static struct nvmem_layout imx_ocotp_layout = {
 595         .fixup_cell_info = imx_ocotp_fixup_cell_info,
 596 };
 597
 598 static int imx_ocotp_probe(struct platform_device *pdev)
 599 {
 600         struct device *dev = &pdev->dev;
 601         struct ocotp_priv *priv;
 602         struct nvmem_device *nvmem;
 603
 604         priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
 605         if (!priv)
 606                 return -ENOMEM;
 607
 608         priv->dev = dev;
 609
 610         priv->base = devm_platform_ioremap_resource(pdev, 0);
 611         if (IS_ERR(priv->base))
 612                 return PTR_ERR(priv->base);
 613
 614         priv->clk = devm_clk_get(dev, NULL);
 615         if (IS_ERR(priv->clk))
 616                 return PTR_ERR(priv->clk);
 617
 618         priv->params = of_device_get_match_data(&pdev->dev);
 619         imx_ocotp_nvmem_config.size = 4 * priv->params->nregs;
 620         imx_ocotp_nvmem_config.dev = dev;
 621         imx_ocotp_nvmem_config.priv = priv;
 622         imx_ocotp_nvmem_config.layout = &imx_ocotp_layout;
 623
 624         priv->config = &imx_ocotp_nvmem_config;
 625
 626         clk_prepare_enable(priv->clk);
 627         imx_ocotp_clr_err_if_set(priv);
 628         clk_disable_unprepare(priv->clk);
 629
 630         nvmem = devm_nvmem_register(dev, &imx_ocotp_nvmem_config);
 631
 632         return PTR_ERR_OR_ZERO(nvmem);
 633 }
 634
 635 static struct platform_driver imx_ocotp_driver = {
 636         .probe  = imx_ocotp_probe,
 637         .driver = {
 638                 .name   = "imx_ocotp",
 639                 .of_match_table = imx_ocotp_dt_ids,
 640         },
 641 };
 642 module_platform_driver(imx_ocotp_driver);
 643
 644 MODULE_AUTHOR("Philipp Zabel <p.zabel@pengutronix.de>");
 645 MODULE_DESCRIPTION("i.MX6/i.MX7 OCOTP fuse box driver");
 646 MODULE_LICENSE("GPL v2");