2 * This file is part of wl1271
4 * Copyright (C) 2009 Nokia Corporation
6 * Contact: Luciano Coelho <luciano.coelho@nokia.com>
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License
10 * version 2 as published by the Free Software Foundation.
12 * This program is distributed in the hope that it will be useful, but
13 * WITHOUT ANY WARRANTY; without even the implied warranty of
14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
15 * General Public License for more details.
17 * You should have received a copy of the GNU General Public License
18 * along with this program; if not, write to the Free Software
19 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
28 CONF_HW_BIT_RATE_1MBPS = BIT(0),
29 CONF_HW_BIT_RATE_2MBPS = BIT(1),
30 CONF_HW_BIT_RATE_5_5MBPS = BIT(2),
31 CONF_HW_BIT_RATE_6MBPS = BIT(3),
32 CONF_HW_BIT_RATE_9MBPS = BIT(4),
33 CONF_HW_BIT_RATE_11MBPS = BIT(5),
34 CONF_HW_BIT_RATE_12MBPS = BIT(6),
35 CONF_HW_BIT_RATE_18MBPS = BIT(7),
36 CONF_HW_BIT_RATE_22MBPS = BIT(8),
37 CONF_HW_BIT_RATE_24MBPS = BIT(9),
38 CONF_HW_BIT_RATE_36MBPS = BIT(10),
39 CONF_HW_BIT_RATE_48MBPS = BIT(11),
40 CONF_HW_BIT_RATE_54MBPS = BIT(12),
41 CONF_HW_BIT_RATE_MCS_0 = BIT(13),
42 CONF_HW_BIT_RATE_MCS_1 = BIT(14),
43 CONF_HW_BIT_RATE_MCS_2 = BIT(15),
44 CONF_HW_BIT_RATE_MCS_3 = BIT(16),
45 CONF_HW_BIT_RATE_MCS_4 = BIT(17),
46 CONF_HW_BIT_RATE_MCS_5 = BIT(18),
47 CONF_HW_BIT_RATE_MCS_6 = BIT(19),
48 CONF_HW_BIT_RATE_MCS_7 = BIT(20)
52 CONF_HW_RATE_INDEX_1MBPS = 0,
53 CONF_HW_RATE_INDEX_2MBPS = 1,
54 CONF_HW_RATE_INDEX_5_5MBPS = 2,
55 CONF_HW_RATE_INDEX_6MBPS = 3,
56 CONF_HW_RATE_INDEX_9MBPS = 4,
57 CONF_HW_RATE_INDEX_11MBPS = 5,
58 CONF_HW_RATE_INDEX_12MBPS = 6,
59 CONF_HW_RATE_INDEX_18MBPS = 7,
60 CONF_HW_RATE_INDEX_22MBPS = 8,
61 CONF_HW_RATE_INDEX_24MBPS = 9,
62 CONF_HW_RATE_INDEX_36MBPS = 10,
63 CONF_HW_RATE_INDEX_48MBPS = 11,
64 CONF_HW_RATE_INDEX_54MBPS = 12,
65 CONF_HW_RATE_INDEX_MAX = CONF_HW_RATE_INDEX_54MBPS,
68 #define CONF_HW_RXTX_RATE_UNSUPPORTED 0xff
78 * Configure the min and max time BT gains the antenna
79 * in WLAN / BT master basic rate
83 CONF_SG_ACL_BT_MASTER_MIN_BR = 0,
84 CONF_SG_ACL_BT_MASTER_MAX_BR,
87 * Configure the min and max time BT gains the antenna
88 * in WLAN / BT slave basic rate
92 CONF_SG_ACL_BT_SLAVE_MIN_BR,
93 CONF_SG_ACL_BT_SLAVE_MAX_BR,
96 * Configure the min and max time BT gains the antenna
97 * in WLAN / BT master EDR
101 CONF_SG_ACL_BT_MASTER_MIN_EDR,
102 CONF_SG_ACL_BT_MASTER_MAX_EDR,
105 * Configure the min and max time BT gains the antenna
106 * in WLAN / BT slave EDR
108 * Range: 0 - 255 (ms)
110 CONF_SG_ACL_BT_SLAVE_MIN_EDR,
111 CONF_SG_ACL_BT_SLAVE_MAX_EDR,
114 * The maximum time WLAN can gain the antenna
115 * in WLAN PSM / BT master/slave BR
117 * Range: 0 - 255 (ms)
119 CONF_SG_ACL_WLAN_PS_MASTER_BR,
120 CONF_SG_ACL_WLAN_PS_SLAVE_BR,
123 * The maximum time WLAN can gain the antenna
124 * in WLAN PSM / BT master/slave EDR
126 * Range: 0 - 255 (ms)
128 CONF_SG_ACL_WLAN_PS_MASTER_EDR,
129 CONF_SG_ACL_WLAN_PS_SLAVE_EDR,
131 /* TODO: explain these values */
132 CONF_SG_ACL_WLAN_ACTIVE_MASTER_MIN_BR,
133 CONF_SG_ACL_WLAN_ACTIVE_MASTER_MAX_BR,
134 CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MIN_BR,
135 CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MAX_BR,
136 CONF_SG_ACL_WLAN_ACTIVE_MASTER_MIN_EDR,
137 CONF_SG_ACL_WLAN_ACTIVE_MASTER_MAX_EDR,
138 CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MIN_EDR,
139 CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MAX_EDR,
141 CONF_SG_ACL_ACTIVE_SCAN_WLAN_BR,
142 CONF_SG_ACL_ACTIVE_SCAN_WLAN_EDR,
143 CONF_SG_ACL_PASSIVE_SCAN_BT_BR,
144 CONF_SG_ACL_PASSIVE_SCAN_WLAN_BR,
145 CONF_SG_ACL_PASSIVE_SCAN_BT_EDR,
146 CONF_SG_ACL_PASSIVE_SCAN_WLAN_EDR,
149 * Compensation percentage of probe requests when scan initiated
150 * during BT voice/ACL link.
154 CONF_SG_AUTO_SCAN_PROBE_REQ,
157 * Compensation percentage of probe requests when active scan initiated
162 CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_HV3,
165 * Compensation percentage of WLAN active scan window if initiated
168 * Range: 0 - 1000 (%)
170 CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_A2DP,
173 * Compensation percentage of WLAN passive scan window if initiated
176 * Range: 0 - 1000 (%)
178 CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_A2DP_BR,
181 * Compensation percentage of WLAN passive scan window if initiated
184 * Range: 0 - 1000 (%)
186 CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_A2DP_EDR,
189 * Compensation percentage of WLAN passive scan window if initiated
192 * Range: 0 - 1000 (%)
194 CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_HV3,
196 /* TODO: explain these values */
197 CONF_SG_CONSECUTIVE_HV3_IN_PASSIVE_SCAN,
198 CONF_SG_BCN_HV3_COLLISION_THRESH_IN_PASSIVE_SCAN,
199 CONF_SG_TX_RX_PROTECTION_BWIDTH_IN_PASSIVE_SCAN,
202 * Defines whether the SG will force WLAN host to enter/exit PSM
204 * Range: 1 - SG can force, 0 - host handles PSM
206 CONF_SG_STA_FORCE_PS_IN_BT_SCO,
209 * Defines antenna configuration (single/dual antenna)
211 * Range: 0 - single antenna, 1 - dual antenna
213 CONF_SG_ANTENNA_CONFIGURATION,
216 * The threshold (percent) of max consecutive beacon misses before
217 * increasing priority of beacon reception.
221 CONF_SG_BEACON_MISS_PERCENT,
224 * Protection time of the DHCP procedure.
226 * Range: 0 - 100000 (ms)
231 * RX guard time before the beginning of a new BT voice frame during
232 * which no new WLAN trigger frame is transmitted.
234 * Range: 0 - 100000 (us)
239 * TX guard time before the beginning of a new BT voice frame during
240 * which no new WLAN frame is transmitted.
242 * Range: 0 - 100000 (us)
248 * Enable adaptive RXT/TXT algorithm. If disabled, the host values
251 * Range: 0 - disable, 1 - enable
253 CONF_SG_ADAPTIVE_RXT_TXT,
255 /* TODO: explain this value */
256 CONF_SG_GENERAL_USAGE_BIT_MAP,
259 * Number of consecutive BT voice frames not interrupted by WLAN
263 CONF_SG_HV3_MAX_SERVED,
266 * The used WLAN legacy service period during active BT ACL link
268 * Range: 0 - 255 (ms)
270 CONF_SG_PS_POLL_TIMEOUT,
273 * The used WLAN UPSD service period during active BT ACL link
275 * Range: 0 - 255 (ms)
277 CONF_SG_UPSD_TIMEOUT,
279 CONF_SG_CONSECUTIVE_CTS_THRESHOLD,
280 CONF_SG_STA_RX_WINDOW_AFTER_DTIM,
281 CONF_SG_STA_CONNECTION_PROTECTION_TIME,
284 CONF_AP_BEACON_MISS_TX,
285 CONF_AP_RX_WINDOW_AFTER_BEACON,
286 CONF_AP_BEACON_WINDOW_INTERVAL,
287 CONF_AP_CONNECTION_PROTECTION_TIME,
288 CONF_AP_BT_ACL_VAL_BT_SERVE_TIME,
289 CONF_AP_BT_ACL_VAL_WL_SERVE_TIME,
291 /* CTS Diluting params */
292 CONF_SG_CTS_DILUTED_BAD_RX_PACKETS_TH,
293 CONF_SG_CTS_CHOP_IN_DUAL_ANT_SCO_MASTER,
295 CONF_SG_TEMP_PARAM_1,
296 CONF_SG_TEMP_PARAM_2,
297 CONF_SG_TEMP_PARAM_3,
298 CONF_SG_TEMP_PARAM_4,
299 CONF_SG_TEMP_PARAM_5,
300 CONF_SG_TEMP_PARAM_6,
301 CONF_SG_TEMP_PARAM_7,
302 CONF_SG_TEMP_PARAM_8,
303 CONF_SG_TEMP_PARAM_9,
304 CONF_SG_TEMP_PARAM_10,
307 CONF_SG_PARAMS_ALL = 0xff
310 struct conf_sg_settings {
311 u32 params[CONF_SG_PARAMS_MAX];
315 enum conf_rx_queue_type {
316 CONF_RX_QUEUE_TYPE_LOW_PRIORITY, /* All except the high priority */
317 CONF_RX_QUEUE_TYPE_HIGH_PRIORITY, /* Management and voice packets */
320 struct conf_rx_settings {
322 * The maximum amount of time, in TU, before the
323 * firmware discards the MSDU.
325 * Range: 0 - 0xFFFFFFFF
327 u32 rx_msdu_life_time;
330 * Packet detection threshold in the PHY.
332 * FIXME: details unknown.
334 u32 packet_detection_threshold;
337 * The longest time the STA will wait to receive traffic from the AP
338 * after a PS-poll has been transmitted.
344 * The longest time the STA will wait to receive traffic from the AP
345 * after a frame has been sent from an UPSD enabled queue.
352 * The number of octets in an MPDU, below which an RTS/CTS
353 * handshake is not performed.
360 * The RX Clear Channel Assessment threshold in the PHY
361 * (the energy threshold).
363 * Range: ENABLE_ENERGY_D == 0x140A
364 * DISABLE_ENERGY_D == 0xFFEF
366 u16 rx_cca_threshold;
369 * Occupied Rx mem-blocks number which requires interrupting the host
370 * (0 = no buffering, 0xffff = disabled).
374 u16 irq_blk_threshold;
377 * Rx packets number which requires interrupting the host
378 * (0 = no buffering).
382 u16 irq_pkt_threshold;
385 * Max time in msec the FW may delay RX-Complete interrupt.
394 * Range: RX_QUEUE_TYPE_RX_LOW_PRIORITY, RX_QUEUE_TYPE_RX_HIGH_PRIORITY,
399 #define CONF_TX_MAX_RATE_CLASSES 10
401 #define CONF_TX_RATE_MASK_UNSPECIFIED 0
402 #define CONF_TX_RATE_MASK_BASIC (CONF_HW_BIT_RATE_1MBPS | \
403 CONF_HW_BIT_RATE_2MBPS)
404 #define CONF_TX_RATE_RETRY_LIMIT 10
406 /* basic rates for p2p operations (probe req/resp, etc.) */
407 #define CONF_TX_RATE_MASK_BASIC_P2P (CONF_HW_BIT_RATE_6MBPS | \
408 CONF_HW_BIT_RATE_12MBPS | CONF_HW_BIT_RATE_24MBPS)
411 * Rates supported for data packets when operating as AP. Note the absence
412 * of the 22Mbps rate. There is a FW limitation on 12 rates so we must drop
413 * one. The rate dropped is not mandatory under any operating mode.
415 #define CONF_TX_AP_ENABLED_RATES (CONF_HW_BIT_RATE_1MBPS | \
416 CONF_HW_BIT_RATE_2MBPS | CONF_HW_BIT_RATE_5_5MBPS | \
417 CONF_HW_BIT_RATE_6MBPS | CONF_HW_BIT_RATE_9MBPS | \
418 CONF_HW_BIT_RATE_11MBPS | CONF_HW_BIT_RATE_12MBPS | \
419 CONF_HW_BIT_RATE_18MBPS | CONF_HW_BIT_RATE_24MBPS | \
420 CONF_HW_BIT_RATE_36MBPS | CONF_HW_BIT_RATE_48MBPS | \
421 CONF_HW_BIT_RATE_54MBPS)
423 #define CONF_TX_CCK_RATES (CONF_HW_BIT_RATE_1MBPS | \
424 CONF_HW_BIT_RATE_2MBPS | CONF_HW_BIT_RATE_5_5MBPS | \
425 CONF_HW_BIT_RATE_11MBPS)
427 #define CONF_TX_OFDM_RATES (CONF_HW_BIT_RATE_6MBPS | \
428 CONF_HW_BIT_RATE_12MBPS | CONF_HW_BIT_RATE_24MBPS | \
429 CONF_HW_BIT_RATE_36MBPS | CONF_HW_BIT_RATE_48MBPS | \
430 CONF_HW_BIT_RATE_54MBPS)
432 #define CONF_TX_MCS_RATES (CONF_HW_BIT_RATE_MCS_0 | \
433 CONF_HW_BIT_RATE_MCS_1 | CONF_HW_BIT_RATE_MCS_2 | \
434 CONF_HW_BIT_RATE_MCS_3 | CONF_HW_BIT_RATE_MCS_4 | \
435 CONF_HW_BIT_RATE_MCS_5 | CONF_HW_BIT_RATE_MCS_6 | \
436 CONF_HW_BIT_RATE_MCS_7)
439 * Default rates for management traffic when operating in AP mode. This
440 * should be configured according to the basic rate set of the AP
442 #define CONF_TX_AP_DEFAULT_MGMT_RATES (CONF_HW_BIT_RATE_1MBPS | \
443 CONF_HW_BIT_RATE_2MBPS | CONF_HW_BIT_RATE_5_5MBPS)
445 /* default rates for working as IBSS (11b and OFDM) */
446 #define CONF_TX_IBSS_DEFAULT_RATES (CONF_HW_BIT_RATE_1MBPS | \
447 CONF_HW_BIT_RATE_2MBPS | CONF_HW_BIT_RATE_5_5MBPS | \
448 CONF_HW_BIT_RATE_11MBPS | CONF_TX_OFDM_RATES);
450 struct conf_tx_rate_class {
453 * The rates enabled for this rate class.
455 * Range: CONF_HW_BIT_RATE_* bit mask
460 * The dot11 short retry limit used for TX retries.
464 u8 short_retry_limit;
467 * The dot11 long retry limit used for TX retries.
474 * Flags controlling the attributes of TX transmission.
476 * Range: bit 0: Truncate - when set, FW attempts to send a frame stop
477 * when the total valid per-rate attempts have
478 * been exhausted; otherwise transmissions
479 * will continue at the lowest available rate
480 * until the appropriate one of the
481 * short_retry_limit, long_retry_limit,
482 * dot11_max_transmit_msdu_life_time, or
483 * max_tx_life_time, is exhausted.
484 * 1: Preamble Override - indicates if the preamble type
485 * should be used in TX.
486 * 2: Preamble Type - the type of the preamble to be used by
487 * the policy (0 - long preamble, 1 - short preamble.
492 #define CONF_TX_MAX_AC_COUNT 4
494 /* Slot number setting to start transmission at PIFS interval */
495 #define CONF_TX_AIFS_PIFS 1
496 /* Slot number setting to start transmission at DIFS interval normal
498 #define CONF_TX_AIFS_DIFS 2
502 CONF_TX_AC_BE = 0, /* best effort / legacy */
503 CONF_TX_AC_BK = 1, /* background */
504 CONF_TX_AC_VI = 2, /* video */
505 CONF_TX_AC_VO = 3, /* voice */
506 CONF_TX_AC_CTS2SELF = 4, /* fictitious AC, follows AC_VO */
507 CONF_TX_AC_ANY_TID = 0x1f
510 struct conf_tx_ac_category {
512 * The AC class identifier.
514 * Range: enum conf_tx_ac
519 * The contention window minimum size (in slots) for the access
527 * The contention window maximum size (in slots) for the access
535 * The AIF value (in slots) for the access class.
542 * The TX Op Limit (in microseconds) for the access class.
549 #define CONF_TX_MAX_TID_COUNT 8
551 /* Allow TX BA on all TIDs but 6,7. These are currently reserved in the FW */
552 #define CONF_TX_BA_ENABLED_TID_BITMAP 0x3F
555 CONF_CHANNEL_TYPE_DCF = 0, /* DC/LEGACY*/
556 CONF_CHANNEL_TYPE_EDCF = 1, /* EDCA*/
557 CONF_CHANNEL_TYPE_HCCA = 2, /* HCCA*/
561 CONF_PS_SCHEME_LEGACY = 0,
562 CONF_PS_SCHEME_UPSD_TRIGGER = 1,
563 CONF_PS_SCHEME_LEGACY_PSPOLL = 2,
564 CONF_PS_SCHEME_SAPSD = 3,
568 CONF_ACK_POLICY_LEGACY = 0,
569 CONF_ACK_POLICY_NO_ACK = 1,
570 CONF_ACK_POLICY_BLOCK = 2,
583 struct conf_tx_settings {
585 * The TX ED value for TELEC Enable/Disable.
589 u8 tx_energy_detection;
592 * Configuration for rate classes for TX (currently only one
593 * rate class supported). Used in non-AP mode.
595 struct conf_tx_rate_class sta_rc_conf;
598 * Configuration for access categories for TX rate control.
601 struct conf_tx_ac_category ac_conf[CONF_TX_MAX_AC_COUNT];
604 * AP-mode - allow this number of TX retries to a station before an
605 * event is triggered from FW.
606 * In AP-mode the hlids of unreachable stations are given in the
607 * "sta_tx_retry_exceeded" member in the event mailbox.
612 * AP-mode - after this number of seconds a connected station is
613 * considered inactive.
618 * Configuration for TID parameters.
621 struct conf_tx_tid tid_conf[CONF_TX_MAX_TID_COUNT];
624 * The TX fragmentation threshold.
631 * Max time in msec the FW may delay frame TX-Complete interrupt.
635 u16 tx_compl_timeout;
638 * Completed TX packet count which requires to issue the TX-Complete
643 u16 tx_compl_threshold;
646 * The rate used for control messages and scanning on the 2.4GHz band
648 * Range: CONF_HW_BIT_RATE_* bit mask
653 * The rate used for control messages and scanning on the 5GHz band
655 * Range: CONF_HW_BIT_RATE_* bit mask
660 * TX retry limits for templates
662 u8 tmpl_short_retry_limit;
663 u8 tmpl_long_retry_limit;
665 /* Time in ms for Tx watchdog timer to expire */
666 u32 tx_watchdog_timeout;
670 CONF_WAKE_UP_EVENT_BEACON = 0x01, /* Wake on every Beacon*/
671 CONF_WAKE_UP_EVENT_DTIM = 0x02, /* Wake on every DTIM*/
672 CONF_WAKE_UP_EVENT_N_DTIM = 0x04, /* Wake every Nth DTIM */
673 CONF_WAKE_UP_EVENT_N_BEACONS = 0x08, /* Wake every Nth beacon */
674 CONF_WAKE_UP_EVENT_BITS_MASK = 0x0F
677 #define CONF_MAX_BCN_FILT_IE_COUNT 32
679 #define CONF_BCN_RULE_PASS_ON_CHANGE BIT(0)
680 #define CONF_BCN_RULE_PASS_ON_APPEARANCE BIT(1)
682 #define CONF_BCN_IE_OUI_LEN 3
683 #define CONF_BCN_IE_VER_LEN 2
685 struct conf_bcn_filt_rule {
687 * IE number to which to associate a rule.
694 * Rule to associate with the specific ie.
696 * Range: CONF_BCN_RULE_PASS_ON_*
701 * OUI for the vendor specifie IE (221)
703 u8 oui[CONF_BCN_IE_OUI_LEN];
706 * Type for the vendor specifie IE (221)
711 * Version for the vendor specifie IE (221)
713 u8 version[CONF_BCN_IE_VER_LEN];
716 #define CONF_MAX_RSSI_SNR_TRIGGERS 8
719 CONF_TRIG_METRIC_RSSI_BEACON = 0,
720 CONF_TRIG_METRIC_RSSI_DATA,
721 CONF_TRIG_METRIC_SNR_BEACON,
722 CONF_TRIG_METRIC_SNR_DATA
726 CONF_TRIG_EVENT_TYPE_LEVEL = 0,
727 CONF_TRIG_EVENT_TYPE_EDGE
731 CONF_TRIG_EVENT_DIR_LOW = 0,
732 CONF_TRIG_EVENT_DIR_HIGH,
733 CONF_TRIG_EVENT_DIR_BIDIR
736 struct conf_sig_weights {
739 * RSSI from beacons average weight.
743 u8 rssi_bcn_avg_weight;
746 * RSSI from data average weight.
750 u8 rssi_pkt_avg_weight;
753 * SNR from beacons average weight.
757 u8 snr_bcn_avg_weight;
760 * SNR from data average weight.
764 u8 snr_pkt_avg_weight;
767 enum conf_bcn_filt_mode {
768 CONF_BCN_FILT_MODE_DISABLED = 0,
769 CONF_BCN_FILT_MODE_ENABLED = 1
773 CONF_BET_MODE_DISABLE = 0,
774 CONF_BET_MODE_ENABLE = 1,
777 struct conf_conn_settings {
779 * Firmware wakeup conditions configuration. The host may set only
782 * Range: CONF_WAKE_UP_EVENT_*
787 * Listen interval for beacons or Dtims.
789 * Range: 0 for beacon and Dtim wakeup
791 * 1-255 for x beacons
796 * Firmware wakeup conditions during suspend
797 * Range: CONF_WAKE_UP_EVENT_*
799 u8 suspend_wake_up_event;
802 * Listen interval during suspend.
803 * Currently will be in DTIMs (1-10)
806 u8 suspend_listen_interval;
809 * Enable or disable the beacon filtering.
811 * Range: CONF_BCN_FILT_MODE_*
813 enum conf_bcn_filt_mode bcn_filt_mode;
816 * Configure Beacon filter pass-thru rules.
818 u8 bcn_filt_ie_count;
819 struct conf_bcn_filt_rule bcn_filt_ie[CONF_MAX_BCN_FILT_IE_COUNT];
822 * The number of consecutive beacons to lose, before the firmware
823 * becomes out of synch.
827 u32 synch_fail_thold;
830 * After out-of-synch, the number of TU's to wait without a further
831 * received beacon (or probe response) before issuing the BSS_EVENT_LOSE
836 u32 bss_lose_timeout;
839 * Beacon receive timeout.
843 u32 beacon_rx_timeout;
846 * Broadcast receive timeout.
850 u32 broadcast_timeout;
853 * Enable/disable reception of broadcast packets in power save mode
855 * Range: 1 - enable, 0 - disable
857 u8 rx_broadcast_in_ps;
860 * Consecutive PS Poll failures before sending event to driver
864 u8 ps_poll_threshold;
867 * Configuration of signal average weights.
869 struct conf_sig_weights sig_weights;
872 * Specifies if beacon early termination procedure is enabled or
875 * Range: CONF_BET_MODE_*
880 * Specifies the maximum number of consecutive beacons that may be
881 * early terminated. After this number is reached at least one full
882 * beacon must be correctly received in FW before beacon ET
887 u8 bet_max_consecutive;
890 * Specifies the maximum number of times to try PSM entry if it fails
891 * (if sending the appropriate null-func message fails.)
895 u8 psm_entry_retries;
898 * Specifies the maximum number of times to try PSM exit if it fails
899 * (if sending the appropriate null-func message fails.)
906 * Specifies the maximum number of times to try transmit the PSM entry
907 * null-func frame for each PSM entry attempt
911 u8 psm_entry_nullfunc_retries;
914 * Specifies the dynamic PS timeout in ms that will be used
915 * by the FW when in AUTO_PS mode
917 u16 dynamic_ps_timeout;
920 * Specifies whether dynamic PS should be disabled and PSM forced.
921 * This is required for certain WiFi certification tests.
927 * Specifies the interval of the connection keep-alive null-func
930 * Range: 1000 - 3600000
932 u32 keep_alive_interval;
935 * Maximum listen interval supported by the driver in units of beacons.
939 u8 max_listen_interval;
947 CONF_REF_CLK_38_4_M_XTAL,
948 CONF_REF_CLK_26_M_XTAL,
951 enum single_dual_band_enum {
956 #define CONF_RSSI_AND_PROCESS_COMPENSATION_SIZE 15
957 #define CONF_NUMBER_OF_SUB_BANDS_5 7
958 #define CONF_NUMBER_OF_RATE_GROUPS 6
959 #define CONF_NUMBER_OF_CHANNELS_2_4 14
960 #define CONF_NUMBER_OF_CHANNELS_5 35
962 struct conf_itrim_settings {
963 /* enable dco itrim */
966 /* moderation timeout in microsecs from the last TX */
970 struct conf_pm_config_settings {
972 * Host clock settling time
974 * Range: 0 - 30000 us
976 u32 host_clk_settling_time;
979 * Host fast wakeup support
983 bool host_fast_wakeup_support;
986 struct conf_roam_trigger_settings {
988 * The minimum interval between two trigger events.
990 * Range: 0 - 60000 ms
995 * The weight for rssi/beacon average calculation
999 u8 avg_weight_rssi_beacon;
1002 * The weight for rssi/data frame average calculation
1006 u8 avg_weight_rssi_data;
1009 * The weight for snr/beacon average calculation
1013 u8 avg_weight_snr_beacon;
1016 * The weight for snr/data frame average calculation
1020 u8 avg_weight_snr_data;
1023 struct conf_scan_settings {
1025 * The minimum time to wait on each channel for active scans
1027 * Range: u32 tu/1000
1029 u32 min_dwell_time_active;
1032 * The maximum time to wait on each channel for active scans
1034 * Range: u32 tu/1000
1036 u32 max_dwell_time_active;
1039 * The minimum time to wait on each channel for passive scans
1041 * Range: u32 tu/1000
1043 u32 min_dwell_time_passive;
1046 * The maximum time to wait on each channel for passive scans
1048 * Range: u32 tu/1000
1050 u32 max_dwell_time_passive;
1053 * Number of probe requests to transmit on each active scan channel
1060 * Scan trigger (split scan) timeout. The FW will split the scan
1061 * operation into slices of the given time and allow the FW to schedule
1062 * other tasks in between.
1064 * Range: u32 Microsecs
1066 u32 split_scan_timeout;
1069 struct conf_sched_scan_settings {
1071 * The base time to wait on the channel for active scans (in TU/1000).
1072 * The minimum dwell time is calculated according to this:
1073 * min_dwell_time = base + num_of_probes_to_be_sent * delta_per_probe
1074 * The maximum dwell time is calculated according to this:
1075 * max_dwell_time = min_dwell_time + max_dwell_time_delta
1077 u32 base_dwell_time;
1079 /* The delta between the min dwell time and max dwell time for
1080 * active scans (in TU/1000s). The max dwell time is used by the FW once
1081 * traffic is detected on the channel.
1083 u32 max_dwell_time_delta;
1085 /* Delta added to min dwell time per each probe in 2.4 GHz (TU/1000) */
1086 u32 dwell_time_delta_per_probe;
1088 /* Delta added to min dwell time per each probe in 5 GHz (TU/1000) */
1089 u32 dwell_time_delta_per_probe_5;
1091 /* time to wait on the channel for passive scans (in TU/1000) */
1092 u32 dwell_time_passive;
1094 /* time to wait on the channel for DFS scans (in TU/1000) */
1097 /* number of probe requests to send on each channel in active scans */
1100 /* RSSI threshold to be used for filtering */
1103 /* SNR threshold to be used for filtering */
1107 struct conf_ht_setting {
1110 u16 inactivity_timeout;
1112 /* bitmap of enabled TIDs for TX BA sessions */
1113 u8 tx_ba_tid_bitmap;
1116 struct conf_memory_settings {
1117 /* Number of stations supported in IBSS mode */
1120 /* Number of ssid profiles used in IBSS mode */
1123 /* Number of memory buffers allocated to rx pool */
1126 /* Minimum number of blocks allocated to tx pool */
1127 u8 tx_min_block_num;
1129 /* Disable/Enable dynamic memory */
1133 * Minimum required free tx memory blocks in order to assure optimum
1138 u8 min_req_tx_blocks;
1141 * Minimum required free rx memory blocks in order to assure optimum
1146 u8 min_req_rx_blocks;
1149 * Minimum number of mem blocks (free+used) guaranteed for TX
1156 struct conf_fm_coex {
1159 u8 n_divider_fref_set_1;
1160 u8 n_divider_fref_set_2;
1161 u16 m_divider_fref_set_1;
1162 u16 m_divider_fref_set_2;
1163 u32 coex_pll_stabilization_time;
1164 u16 ldo_stabilization_time;
1165 u8 fm_disturbed_band_margin;
1166 u8 swallow_clk_diff;
1169 struct conf_rx_streaming_settings {
1171 * RX Streaming duration (in msec) from last tx/rx
1178 * Bitmap of tids to be polled during RX streaming.
1179 * (Note: it doesn't look like it really matters)
1186 * RX Streaming interval.
1187 * (Note:this value is also used as the rx streaming timeout)
1188 * Range: 0 (disabled), 10 - 100
1193 * enable rx streaming also when there is no coex activity
1199 /* Continuous or on-demand */
1203 * Number of memory blocks dedicated for the FW logger
1205 * Range: 1-3, or 0 to disable the FW logger
1209 /* Minimum log level threshold */
1212 /* Include/exclude timestamps from the log messages */
1215 /* See enum wl1271_fwlogger_output */
1218 /* Regulates the frequency of log messages */
1222 #define ACX_RATE_MGMT_NUM_OF_RATES 13
1223 struct conf_rate_policy_settings {
1224 u16 rate_retry_score;
1229 u8 inverse_curiosity_factor;
1238 u8 rate_retry_policy[ACX_RATE_MGMT_NUM_OF_RATES];
1241 struct conf_hangover_settings {
1245 u8 early_termination_mode;
1255 struct wlcore_conf {
1256 struct conf_sg_settings sg;
1257 struct conf_rx_settings rx;
1258 struct conf_tx_settings tx;
1259 struct conf_conn_settings conn;
1260 struct conf_itrim_settings itrim;
1261 struct conf_pm_config_settings pm_config;
1262 struct conf_roam_trigger_settings roam_trigger;
1263 struct conf_scan_settings scan;
1264 struct conf_sched_scan_settings sched_scan;
1265 struct conf_ht_setting ht;
1266 struct conf_memory_settings mem_wl127x;
1267 struct conf_memory_settings mem_wl128x;
1268 struct conf_fm_coex fm_coex;
1269 struct conf_rx_streaming_settings rx_streaming;
1270 struct conf_fwlog fwlog;
1271 struct conf_rate_policy_settings rate;
1272 struct conf_hangover_settings hangover;