1 // SPDX-License-Identifier: GPL-2.0-or-later
3 Copyright (C) 2010 Willow Garage <http://www.willowgarage.com>
4 Copyright (C) 2004 - 2010 Ivo van Doorn <IvDoorn@gmail.com>
5 <http://rt2x00.serialmonkey.com>
11 Abstract: rt2x00 generic device routines.
14 #include <linux/kernel.h>
15 #include <linux/module.h>
16 #include <linux/slab.h>
17 #include <linux/log2.h>
19 #include <linux/of_net.h>
22 #include "rt2x00lib.h"
27 u32 rt2x00lib_get_bssidx(struct rt2x00_dev *rt2x00dev,
28 struct ieee80211_vif *vif)
31 * When in STA mode, bssidx is always 0 otherwise local_address[5]
32 * contains the bss number, see BSS_ID_MASK comments for details.
34 if (rt2x00dev->intf_sta_count)
36 return vif->addr[5] & (rt2x00dev->ops->max_ap_intf - 1);
38 EXPORT_SYMBOL_GPL(rt2x00lib_get_bssidx);
41 * Radio control handlers.
43 int rt2x00lib_enable_radio(struct rt2x00_dev *rt2x00dev)
48 * Don't enable the radio twice.
49 * And check if the hardware button has been disabled.
51 if (test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
55 * Initialize all data queues.
57 rt2x00queue_init_queues(rt2x00dev);
63 rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_RADIO_ON);
67 rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_RADIO_IRQ_ON);
69 rt2x00leds_led_radio(rt2x00dev, true);
70 rt2x00led_led_activity(rt2x00dev, true);
72 set_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags);
77 rt2x00queue_start_queues(rt2x00dev);
78 rt2x00link_start_tuner(rt2x00dev);
81 * Start watchdog monitoring.
83 rt2x00link_start_watchdog(rt2x00dev);
88 void rt2x00lib_disable_radio(struct rt2x00_dev *rt2x00dev)
90 if (!test_and_clear_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
94 * Stop watchdog monitoring.
96 rt2x00link_stop_watchdog(rt2x00dev);
101 rt2x00link_stop_tuner(rt2x00dev);
102 rt2x00queue_stop_queues(rt2x00dev);
103 rt2x00queue_flush_queues(rt2x00dev, true);
108 rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_RADIO_OFF);
109 rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_RADIO_IRQ_OFF);
110 rt2x00led_led_activity(rt2x00dev, false);
111 rt2x00leds_led_radio(rt2x00dev, false);
114 static void rt2x00lib_intf_scheduled_iter(void *data, u8 *mac,
115 struct ieee80211_vif *vif)
117 struct rt2x00_dev *rt2x00dev = data;
118 struct rt2x00_intf *intf = vif_to_intf(vif);
121 * It is possible the radio was disabled while the work had been
122 * scheduled. If that happens we should return here immediately,
123 * note that in the spinlock protected area above the delayed_flags
124 * have been cleared correctly.
126 if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
129 if (test_and_clear_bit(DELAYED_UPDATE_BEACON, &intf->delayed_flags)) {
130 mutex_lock(&intf->beacon_skb_mutex);
131 rt2x00queue_update_beacon(rt2x00dev, vif);
132 mutex_unlock(&intf->beacon_skb_mutex);
136 static void rt2x00lib_intf_scheduled(struct work_struct *work)
138 struct rt2x00_dev *rt2x00dev =
139 container_of(work, struct rt2x00_dev, intf_work);
142 * Iterate over each interface and perform the
143 * requested configurations.
145 ieee80211_iterate_active_interfaces(rt2x00dev->hw,
146 IEEE80211_IFACE_ITER_RESUME_ALL,
147 rt2x00lib_intf_scheduled_iter,
151 static void rt2x00lib_autowakeup(struct work_struct *work)
153 struct rt2x00_dev *rt2x00dev =
154 container_of(work, struct rt2x00_dev, autowakeup_work.work);
156 if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags))
159 if (rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_AWAKE))
160 rt2x00_err(rt2x00dev, "Device failed to wakeup\n");
161 clear_bit(CONFIG_POWERSAVING, &rt2x00dev->flags);
165 * Interrupt context handlers.
167 static void rt2x00lib_bc_buffer_iter(void *data, u8 *mac,
168 struct ieee80211_vif *vif)
170 struct ieee80211_tx_control control = {};
171 struct rt2x00_dev *rt2x00dev = data;
175 * Only AP mode interfaces do broad- and multicast buffering
177 if (vif->type != NL80211_IFTYPE_AP)
181 * Send out buffered broad- and multicast frames
183 skb = ieee80211_get_buffered_bc(rt2x00dev->hw, vif);
185 rt2x00mac_tx(rt2x00dev->hw, &control, skb);
186 skb = ieee80211_get_buffered_bc(rt2x00dev->hw, vif);
190 static void rt2x00lib_beaconupdate_iter(void *data, u8 *mac,
191 struct ieee80211_vif *vif)
193 struct rt2x00_dev *rt2x00dev = data;
195 if (vif->type != NL80211_IFTYPE_AP &&
196 vif->type != NL80211_IFTYPE_ADHOC &&
197 vif->type != NL80211_IFTYPE_MESH_POINT &&
198 vif->type != NL80211_IFTYPE_WDS)
202 * Update the beacon without locking. This is safe on PCI devices
203 * as they only update the beacon periodically here. This should
204 * never be called for USB devices.
206 WARN_ON(rt2x00_is_usb(rt2x00dev));
207 rt2x00queue_update_beacon(rt2x00dev, vif);
210 void rt2x00lib_beacondone(struct rt2x00_dev *rt2x00dev)
212 if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
215 /* send buffered bc/mc frames out for every bssid */
216 ieee80211_iterate_active_interfaces_atomic(
217 rt2x00dev->hw, IEEE80211_IFACE_ITER_RESUME_ALL,
218 rt2x00lib_bc_buffer_iter, rt2x00dev);
220 * Devices with pre tbtt interrupt don't need to update the beacon
221 * here as they will fetch the next beacon directly prior to
224 if (rt2x00_has_cap_pre_tbtt_interrupt(rt2x00dev))
227 /* fetch next beacon */
228 ieee80211_iterate_active_interfaces_atomic(
229 rt2x00dev->hw, IEEE80211_IFACE_ITER_RESUME_ALL,
230 rt2x00lib_beaconupdate_iter, rt2x00dev);
232 EXPORT_SYMBOL_GPL(rt2x00lib_beacondone);
234 void rt2x00lib_pretbtt(struct rt2x00_dev *rt2x00dev)
236 if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
239 /* fetch next beacon */
240 ieee80211_iterate_active_interfaces_atomic(
241 rt2x00dev->hw, IEEE80211_IFACE_ITER_RESUME_ALL,
242 rt2x00lib_beaconupdate_iter, rt2x00dev);
244 EXPORT_SYMBOL_GPL(rt2x00lib_pretbtt);
246 void rt2x00lib_dmastart(struct queue_entry *entry)
248 set_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags);
249 rt2x00queue_index_inc(entry, Q_INDEX);
251 EXPORT_SYMBOL_GPL(rt2x00lib_dmastart);
253 void rt2x00lib_dmadone(struct queue_entry *entry)
255 set_bit(ENTRY_DATA_STATUS_PENDING, &entry->flags);
256 clear_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags);
257 rt2x00queue_index_inc(entry, Q_INDEX_DMA_DONE);
259 EXPORT_SYMBOL_GPL(rt2x00lib_dmadone);
261 static inline int rt2x00lib_txdone_bar_status(struct queue_entry *entry)
263 struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
264 struct ieee80211_bar *bar = (void *) entry->skb->data;
265 struct rt2x00_bar_list_entry *bar_entry;
268 if (likely(!ieee80211_is_back_req(bar->frame_control)))
272 * Unlike all other frames, the status report for BARs does
273 * not directly come from the hardware as it is incapable of
274 * matching a BA to a previously send BAR. The hardware will
275 * report all BARs as if they weren't acked at all.
277 * Instead the RX-path will scan for incoming BAs and set the
278 * block_acked flag if it sees one that was likely caused by
281 * Remove remaining BARs here and return their status for
282 * TX done processing.
286 list_for_each_entry_rcu(bar_entry, &rt2x00dev->bar_list, list) {
287 if (bar_entry->entry != entry)
290 spin_lock_bh(&rt2x00dev->bar_list_lock);
291 /* Return whether this BAR was blockacked or not */
292 ret = bar_entry->block_acked;
293 /* Remove the BAR from our checklist */
294 list_del_rcu(&bar_entry->list);
295 spin_unlock_bh(&rt2x00dev->bar_list_lock);
296 kfree_rcu(bar_entry, head);
305 static void rt2x00lib_fill_tx_status(struct rt2x00_dev *rt2x00dev,
306 struct ieee80211_tx_info *tx_info,
307 struct skb_frame_desc *skbdesc,
308 struct txdone_entry_desc *txdesc,
311 u8 rate_idx, rate_flags, retry_rates;
314 rate_idx = skbdesc->tx_rate_idx;
315 rate_flags = skbdesc->tx_rate_flags;
316 retry_rates = test_bit(TXDONE_FALLBACK, &txdesc->flags) ?
317 (txdesc->retry + 1) : 1;
320 * Initialize TX status
322 memset(&tx_info->status, 0, sizeof(tx_info->status));
323 tx_info->status.ack_signal = 0;
326 * Frame was send with retries, hardware tried
327 * different rates to send out the frame, at each
328 * retry it lowered the rate 1 step except when the
329 * lowest rate was used.
331 for (i = 0; i < retry_rates && i < IEEE80211_TX_MAX_RATES; i++) {
332 tx_info->status.rates[i].idx = rate_idx - i;
333 tx_info->status.rates[i].flags = rate_flags;
335 if (rate_idx - i == 0) {
337 * The lowest rate (index 0) was used until the
338 * number of max retries was reached.
340 tx_info->status.rates[i].count = retry_rates - i;
344 tx_info->status.rates[i].count = 1;
346 if (i < (IEEE80211_TX_MAX_RATES - 1))
347 tx_info->status.rates[i].idx = -1; /* terminate */
349 if (test_bit(TXDONE_NO_ACK_REQ, &txdesc->flags))
350 tx_info->flags |= IEEE80211_TX_CTL_NO_ACK;
352 if (!(tx_info->flags & IEEE80211_TX_CTL_NO_ACK)) {
354 tx_info->flags |= IEEE80211_TX_STAT_ACK;
356 rt2x00dev->low_level_stats.dot11ACKFailureCount++;
360 * Every single frame has it's own tx status, hence report
361 * every frame as ampdu of size 1.
363 * TODO: if we can find out how many frames were aggregated
364 * by the hw we could provide the real ampdu_len to mac80211
365 * which would allow the rc algorithm to better decide on
366 * which rates are suitable.
368 if (test_bit(TXDONE_AMPDU, &txdesc->flags) ||
369 tx_info->flags & IEEE80211_TX_CTL_AMPDU) {
370 tx_info->flags |= IEEE80211_TX_STAT_AMPDU |
371 IEEE80211_TX_CTL_AMPDU;
372 tx_info->status.ampdu_len = 1;
373 tx_info->status.ampdu_ack_len = success ? 1 : 0;
376 tx_info->flags |= IEEE80211_TX_STAT_AMPDU_NO_BACK;
379 if (rate_flags & IEEE80211_TX_RC_USE_RTS_CTS) {
381 rt2x00dev->low_level_stats.dot11RTSSuccessCount++;
383 rt2x00dev->low_level_stats.dot11RTSFailureCount++;
387 static void rt2x00lib_clear_entry(struct rt2x00_dev *rt2x00dev,
388 struct queue_entry *entry)
391 * Make this entry available for reuse.
396 rt2x00dev->ops->lib->clear_entry(entry);
398 rt2x00queue_index_inc(entry, Q_INDEX_DONE);
401 * If the data queue was below the threshold before the txdone
402 * handler we must make sure the packet queue in the mac80211 stack
403 * is reenabled when the txdone handler has finished. This has to be
404 * serialized with rt2x00mac_tx(), otherwise we can wake up queue
405 * before it was stopped.
407 spin_lock_bh(&entry->queue->tx_lock);
408 if (!rt2x00queue_threshold(entry->queue))
409 rt2x00queue_unpause_queue(entry->queue);
410 spin_unlock_bh(&entry->queue->tx_lock);
413 void rt2x00lib_txdone_nomatch(struct queue_entry *entry,
414 struct txdone_entry_desc *txdesc)
416 struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
417 struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb);
418 struct ieee80211_tx_info txinfo = {};
424 rt2x00queue_unmap_skb(entry);
427 * Signal that the TX descriptor is no longer in the skb.
429 skbdesc->flags &= ~SKBDESC_DESC_IN_SKB;
432 * Send frame to debugfs immediately, after this call is completed
433 * we are going to overwrite the skb->cb array.
435 rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_TXDONE, entry);
438 * Determine if the frame has been successfully transmitted and
439 * remove BARs from our check list while checking for their
443 rt2x00lib_txdone_bar_status(entry) ||
444 test_bit(TXDONE_SUCCESS, &txdesc->flags);
446 if (!test_bit(TXDONE_UNKNOWN, &txdesc->flags)) {
448 * Update TX statistics.
450 rt2x00dev->link.qual.tx_success += success;
451 rt2x00dev->link.qual.tx_failed += !success;
453 rt2x00lib_fill_tx_status(rt2x00dev, &txinfo, skbdesc, txdesc,
455 ieee80211_tx_status_noskb(rt2x00dev->hw, skbdesc->sta, &txinfo);
458 dev_kfree_skb_any(entry->skb);
459 rt2x00lib_clear_entry(rt2x00dev, entry);
461 EXPORT_SYMBOL_GPL(rt2x00lib_txdone_nomatch);
463 void rt2x00lib_txdone(struct queue_entry *entry,
464 struct txdone_entry_desc *txdesc)
466 struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
467 struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(entry->skb);
468 struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb);
469 u8 skbdesc_flags = skbdesc->flags;
470 unsigned int header_length;
476 rt2x00queue_unmap_skb(entry);
479 * Remove the extra tx headroom from the skb.
481 skb_pull(entry->skb, rt2x00dev->extra_tx_headroom);
484 * Signal that the TX descriptor is no longer in the skb.
486 skbdesc->flags &= ~SKBDESC_DESC_IN_SKB;
489 * Determine the length of 802.11 header.
491 header_length = ieee80211_get_hdrlen_from_skb(entry->skb);
494 * Remove L2 padding which was added during
496 if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_L2PAD))
497 rt2x00queue_remove_l2pad(entry->skb, header_length);
500 * If the IV/EIV data was stripped from the frame before it was
501 * passed to the hardware, we should now reinsert it again because
502 * mac80211 will expect the same data to be present it the
503 * frame as it was passed to us.
505 if (rt2x00_has_cap_hw_crypto(rt2x00dev))
506 rt2x00crypto_tx_insert_iv(entry->skb, header_length);
509 * Send frame to debugfs immediately, after this call is completed
510 * we are going to overwrite the skb->cb array.
512 rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_TXDONE, entry);
515 * Determine if the frame has been successfully transmitted and
516 * remove BARs from our check list while checking for their
520 rt2x00lib_txdone_bar_status(entry) ||
521 test_bit(TXDONE_SUCCESS, &txdesc->flags) ||
522 test_bit(TXDONE_UNKNOWN, &txdesc->flags);
525 * Update TX statistics.
527 rt2x00dev->link.qual.tx_success += success;
528 rt2x00dev->link.qual.tx_failed += !success;
530 rt2x00lib_fill_tx_status(rt2x00dev, tx_info, skbdesc, txdesc, success);
533 * Only send the status report to mac80211 when it's a frame
534 * that originated in mac80211. If this was a extra frame coming
535 * through a mac80211 library call (RTS/CTS) then we should not
536 * send the status report back.
538 if (!(skbdesc_flags & SKBDESC_NOT_MAC80211)) {
539 if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_TASKLET_CONTEXT))
540 ieee80211_tx_status(rt2x00dev->hw, entry->skb);
542 ieee80211_tx_status_ni(rt2x00dev->hw, entry->skb);
544 dev_kfree_skb_any(entry->skb);
547 rt2x00lib_clear_entry(rt2x00dev, entry);
549 EXPORT_SYMBOL_GPL(rt2x00lib_txdone);
551 void rt2x00lib_txdone_noinfo(struct queue_entry *entry, u32 status)
553 struct txdone_entry_desc txdesc;
556 __set_bit(status, &txdesc.flags);
559 rt2x00lib_txdone(entry, &txdesc);
561 EXPORT_SYMBOL_GPL(rt2x00lib_txdone_noinfo);
563 static u8 *rt2x00lib_find_ie(u8 *data, unsigned int len, u8 ie)
565 struct ieee80211_mgmt *mgmt = (void *)data;
568 pos = (u8 *)mgmt->u.beacon.variable;
571 if (pos + 2 + pos[1] > end)
583 static void rt2x00lib_sleep(struct work_struct *work)
585 struct rt2x00_dev *rt2x00dev =
586 container_of(work, struct rt2x00_dev, sleep_work);
588 if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags))
592 * Check again is powersaving is enabled, to prevent races from delayed
595 if (!test_bit(CONFIG_POWERSAVING, &rt2x00dev->flags))
596 rt2x00lib_config(rt2x00dev, &rt2x00dev->hw->conf,
597 IEEE80211_CONF_CHANGE_PS);
600 static void rt2x00lib_rxdone_check_ba(struct rt2x00_dev *rt2x00dev,
602 struct rxdone_entry_desc *rxdesc)
604 struct rt2x00_bar_list_entry *entry;
605 struct ieee80211_bar *ba = (void *)skb->data;
607 if (likely(!ieee80211_is_back(ba->frame_control)))
610 if (rxdesc->size < sizeof(*ba) + FCS_LEN)
614 list_for_each_entry_rcu(entry, &rt2x00dev->bar_list, list) {
616 if (ba->start_seq_num != entry->start_seq_num)
619 #define TID_CHECK(a, b) ( \
620 ((a) & cpu_to_le16(IEEE80211_BAR_CTRL_TID_INFO_MASK)) == \
621 ((b) & cpu_to_le16(IEEE80211_BAR_CTRL_TID_INFO_MASK))) \
623 if (!TID_CHECK(ba->control, entry->control))
628 if (!ether_addr_equal_64bits(ba->ra, entry->ta))
631 if (!ether_addr_equal_64bits(ba->ta, entry->ra))
634 /* Mark BAR since we received the according BA */
635 spin_lock_bh(&rt2x00dev->bar_list_lock);
636 entry->block_acked = 1;
637 spin_unlock_bh(&rt2x00dev->bar_list_lock);
644 static void rt2x00lib_rxdone_check_ps(struct rt2x00_dev *rt2x00dev,
646 struct rxdone_entry_desc *rxdesc)
648 struct ieee80211_hdr *hdr = (void *) skb->data;
649 struct ieee80211_tim_ie *tim_ie;
654 /* If this is not a beacon, or if mac80211 has no powersaving
655 * configured, or if the device is already in powersaving mode
656 * we can exit now. */
657 if (likely(!ieee80211_is_beacon(hdr->frame_control) ||
658 !(rt2x00dev->hw->conf.flags & IEEE80211_CONF_PS)))
661 /* min. beacon length + FCS_LEN */
662 if (skb->len <= 40 + FCS_LEN)
665 /* and only beacons from the associated BSSID, please */
666 if (!(rxdesc->dev_flags & RXDONE_MY_BSS) ||
670 rt2x00dev->last_beacon = jiffies;
672 tim = rt2x00lib_find_ie(skb->data, skb->len - FCS_LEN, WLAN_EID_TIM);
676 if (tim[1] < sizeof(*tim_ie))
680 tim_ie = (struct ieee80211_tim_ie *) &tim[2];
682 /* Check whenever the PHY can be turned off again. */
684 /* 1. What about buffered unicast traffic for our AID? */
685 cam = ieee80211_check_tim(tim_ie, tim_len, rt2x00dev->aid);
687 /* 2. Maybe the AP wants to send multicast/broadcast data? */
688 cam |= (tim_ie->bitmap_ctrl & 0x01);
690 if (!cam && !test_bit(CONFIG_POWERSAVING, &rt2x00dev->flags))
691 queue_work(rt2x00dev->workqueue, &rt2x00dev->sleep_work);
694 static int rt2x00lib_rxdone_read_signal(struct rt2x00_dev *rt2x00dev,
695 struct rxdone_entry_desc *rxdesc)
697 struct ieee80211_supported_band *sband;
698 const struct rt2x00_rate *rate;
700 int signal = rxdesc->signal;
701 int type = (rxdesc->dev_flags & RXDONE_SIGNAL_MASK);
703 switch (rxdesc->rate_mode) {
707 * For non-HT rates the MCS value needs to contain the
708 * actually used rate modulation (CCK or OFDM).
710 if (rxdesc->dev_flags & RXDONE_SIGNAL_MCS)
711 signal = RATE_MCS(rxdesc->rate_mode, signal);
713 sband = &rt2x00dev->bands[rt2x00dev->curr_band];
714 for (i = 0; i < sband->n_bitrates; i++) {
715 rate = rt2x00_get_rate(sband->bitrates[i].hw_value);
716 if (((type == RXDONE_SIGNAL_PLCP) &&
717 (rate->plcp == signal)) ||
718 ((type == RXDONE_SIGNAL_BITRATE) &&
719 (rate->bitrate == signal)) ||
720 ((type == RXDONE_SIGNAL_MCS) &&
721 (rate->mcs == signal))) {
726 case RATE_MODE_HT_MIX:
727 case RATE_MODE_HT_GREENFIELD:
728 if (signal >= 0 && signal <= 76)
735 rt2x00_warn(rt2x00dev, "Frame received with unrecognized signal, mode=0x%.4x, signal=0x%.4x, type=%d\n",
736 rxdesc->rate_mode, signal, type);
740 void rt2x00lib_rxdone(struct queue_entry *entry, gfp_t gfp)
742 struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
743 struct rxdone_entry_desc rxdesc;
745 struct ieee80211_rx_status *rx_status;
746 unsigned int header_length;
749 if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags) ||
750 !test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
753 if (test_bit(ENTRY_DATA_IO_FAILED, &entry->flags))
757 * Allocate a new sk_buffer. If no new buffer available, drop the
758 * received frame and reuse the existing buffer.
760 skb = rt2x00queue_alloc_rxskb(entry, gfp);
767 rt2x00queue_unmap_skb(entry);
770 * Extract the RXD details.
772 memset(&rxdesc, 0, sizeof(rxdesc));
773 rt2x00dev->ops->lib->fill_rxdone(entry, &rxdesc);
776 * Check for valid size in case we get corrupted descriptor from
779 if (unlikely(rxdesc.size == 0 ||
780 rxdesc.size > entry->queue->data_size)) {
781 rt2x00_err(rt2x00dev, "Wrong frame size %d max %d\n",
782 rxdesc.size, entry->queue->data_size);
783 dev_kfree_skb(entry->skb);
788 * The data behind the ieee80211 header must be
789 * aligned on a 4 byte boundary.
791 header_length = ieee80211_get_hdrlen_from_skb(entry->skb);
794 * Hardware might have stripped the IV/EIV/ICV data,
795 * in that case it is possible that the data was
796 * provided separately (through hardware descriptor)
797 * in which case we should reinsert the data into the frame.
799 if ((rxdesc.dev_flags & RXDONE_CRYPTO_IV) &&
800 (rxdesc.flags & RX_FLAG_IV_STRIPPED))
801 rt2x00crypto_rx_insert_iv(entry->skb, header_length,
803 else if (header_length &&
804 (rxdesc.size > header_length) &&
805 (rxdesc.dev_flags & RXDONE_L2PAD))
806 rt2x00queue_remove_l2pad(entry->skb, header_length);
808 /* Trim buffer to correct size */
809 skb_trim(entry->skb, rxdesc.size);
812 * Translate the signal to the correct bitrate index.
814 rate_idx = rt2x00lib_rxdone_read_signal(rt2x00dev, &rxdesc);
815 if (rxdesc.rate_mode == RATE_MODE_HT_MIX ||
816 rxdesc.rate_mode == RATE_MODE_HT_GREENFIELD)
817 rxdesc.encoding = RX_ENC_HT;
820 * Check if this is a beacon, and more frames have been
821 * buffered while we were in powersaving mode.
823 rt2x00lib_rxdone_check_ps(rt2x00dev, entry->skb, &rxdesc);
826 * Check for incoming BlockAcks to match to the BlockAckReqs
829 rt2x00lib_rxdone_check_ba(rt2x00dev, entry->skb, &rxdesc);
832 * Update extra components
834 rt2x00link_update_stats(rt2x00dev, entry->skb, &rxdesc);
835 rt2x00debug_update_crypto(rt2x00dev, &rxdesc);
836 rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_RXDONE, entry);
839 * Initialize RX status information, and send frame
842 rx_status = IEEE80211_SKB_RXCB(entry->skb);
844 /* Ensure that all fields of rx_status are initialized
845 * properly. The skb->cb array was used for driver
846 * specific informations, so rx_status might contain
849 memset(rx_status, 0, sizeof(*rx_status));
851 rx_status->mactime = rxdesc.timestamp;
852 rx_status->band = rt2x00dev->curr_band;
853 rx_status->freq = rt2x00dev->curr_freq;
854 rx_status->rate_idx = rate_idx;
855 rx_status->signal = rxdesc.rssi;
856 rx_status->flag = rxdesc.flags;
857 rx_status->enc_flags = rxdesc.enc_flags;
858 rx_status->encoding = rxdesc.encoding;
859 rx_status->bw = rxdesc.bw;
860 rx_status->antenna = rt2x00dev->link.ant.active.rx;
862 ieee80211_rx_ni(rt2x00dev->hw, entry->skb);
866 * Replace the skb with the freshly allocated one.
872 rt2x00queue_index_inc(entry, Q_INDEX_DONE);
873 if (test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags) &&
874 test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
875 rt2x00dev->ops->lib->clear_entry(entry);
877 EXPORT_SYMBOL_GPL(rt2x00lib_rxdone);
880 * Driver initialization handlers.
882 const struct rt2x00_rate rt2x00_supported_rates[12] = {
884 .flags = DEV_RATE_CCK,
888 .mcs = RATE_MCS(RATE_MODE_CCK, 0),
891 .flags = DEV_RATE_CCK | DEV_RATE_SHORT_PREAMBLE,
895 .mcs = RATE_MCS(RATE_MODE_CCK, 1),
898 .flags = DEV_RATE_CCK | DEV_RATE_SHORT_PREAMBLE,
902 .mcs = RATE_MCS(RATE_MODE_CCK, 2),
905 .flags = DEV_RATE_CCK | DEV_RATE_SHORT_PREAMBLE,
909 .mcs = RATE_MCS(RATE_MODE_CCK, 3),
912 .flags = DEV_RATE_OFDM,
916 .mcs = RATE_MCS(RATE_MODE_OFDM, 0),
919 .flags = DEV_RATE_OFDM,
923 .mcs = RATE_MCS(RATE_MODE_OFDM, 1),
926 .flags = DEV_RATE_OFDM,
930 .mcs = RATE_MCS(RATE_MODE_OFDM, 2),
933 .flags = DEV_RATE_OFDM,
937 .mcs = RATE_MCS(RATE_MODE_OFDM, 3),
940 .flags = DEV_RATE_OFDM,
944 .mcs = RATE_MCS(RATE_MODE_OFDM, 4),
947 .flags = DEV_RATE_OFDM,
951 .mcs = RATE_MCS(RATE_MODE_OFDM, 5),
954 .flags = DEV_RATE_OFDM,
958 .mcs = RATE_MCS(RATE_MODE_OFDM, 6),
961 .flags = DEV_RATE_OFDM,
965 .mcs = RATE_MCS(RATE_MODE_OFDM, 7),
969 static void rt2x00lib_channel(struct ieee80211_channel *entry,
970 const int channel, const int tx_power,
973 /* XXX: this assumption about the band is wrong for 802.11j */
974 entry->band = channel <= 14 ? NL80211_BAND_2GHZ : NL80211_BAND_5GHZ;
975 entry->center_freq = ieee80211_channel_to_frequency(channel,
977 entry->hw_value = value;
978 entry->max_power = tx_power;
979 entry->max_antenna_gain = 0xff;
982 static void rt2x00lib_rate(struct ieee80211_rate *entry,
983 const u16 index, const struct rt2x00_rate *rate)
986 entry->bitrate = rate->bitrate;
987 entry->hw_value = index;
988 entry->hw_value_short = index;
990 if (rate->flags & DEV_RATE_SHORT_PREAMBLE)
991 entry->flags |= IEEE80211_RATE_SHORT_PREAMBLE;
994 void rt2x00lib_set_mac_address(struct rt2x00_dev *rt2x00dev, u8 *eeprom_mac_addr)
996 const char *mac_addr;
998 mac_addr = of_get_mac_address(rt2x00dev->dev->of_node);
999 if (!IS_ERR(mac_addr))
1000 ether_addr_copy(eeprom_mac_addr, mac_addr);
1002 if (!is_valid_ether_addr(eeprom_mac_addr)) {
1003 eth_random_addr(eeprom_mac_addr);
1004 rt2x00_eeprom_dbg(rt2x00dev, "MAC: %pM\n", eeprom_mac_addr);
1007 EXPORT_SYMBOL_GPL(rt2x00lib_set_mac_address);
1009 static int rt2x00lib_probe_hw_modes(struct rt2x00_dev *rt2x00dev,
1010 struct hw_mode_spec *spec)
1012 struct ieee80211_hw *hw = rt2x00dev->hw;
1013 struct ieee80211_channel *channels;
1014 struct ieee80211_rate *rates;
1015 unsigned int num_rates;
1019 if (spec->supported_rates & SUPPORT_RATE_CCK)
1021 if (spec->supported_rates & SUPPORT_RATE_OFDM)
1024 channels = kcalloc(spec->num_channels, sizeof(*channels), GFP_KERNEL);
1028 rates = kcalloc(num_rates, sizeof(*rates), GFP_KERNEL);
1030 goto exit_free_channels;
1033 * Initialize Rate list.
1035 for (i = 0; i < num_rates; i++)
1036 rt2x00lib_rate(&rates[i], i, rt2x00_get_rate(i));
1039 * Initialize Channel list.
1041 for (i = 0; i < spec->num_channels; i++) {
1042 rt2x00lib_channel(&channels[i],
1043 spec->channels[i].channel,
1044 spec->channels_info[i].max_power, i);
1048 * Intitialize 802.11b, 802.11g
1052 if (spec->supported_bands & SUPPORT_BAND_2GHZ) {
1053 rt2x00dev->bands[NL80211_BAND_2GHZ].n_channels = 14;
1054 rt2x00dev->bands[NL80211_BAND_2GHZ].n_bitrates = num_rates;
1055 rt2x00dev->bands[NL80211_BAND_2GHZ].channels = channels;
1056 rt2x00dev->bands[NL80211_BAND_2GHZ].bitrates = rates;
1057 hw->wiphy->bands[NL80211_BAND_2GHZ] =
1058 &rt2x00dev->bands[NL80211_BAND_2GHZ];
1059 memcpy(&rt2x00dev->bands[NL80211_BAND_2GHZ].ht_cap,
1060 &spec->ht, sizeof(spec->ht));
1064 * Intitialize 802.11a
1066 * Channels: OFDM, UNII, HiperLAN2.
1068 if (spec->supported_bands & SUPPORT_BAND_5GHZ) {
1069 rt2x00dev->bands[NL80211_BAND_5GHZ].n_channels =
1070 spec->num_channels - 14;
1071 rt2x00dev->bands[NL80211_BAND_5GHZ].n_bitrates =
1073 rt2x00dev->bands[NL80211_BAND_5GHZ].channels = &channels[14];
1074 rt2x00dev->bands[NL80211_BAND_5GHZ].bitrates = &rates[4];
1075 hw->wiphy->bands[NL80211_BAND_5GHZ] =
1076 &rt2x00dev->bands[NL80211_BAND_5GHZ];
1077 memcpy(&rt2x00dev->bands[NL80211_BAND_5GHZ].ht_cap,
1078 &spec->ht, sizeof(spec->ht));
1085 rt2x00_err(rt2x00dev, "Allocation ieee80211 modes failed\n");
1089 static void rt2x00lib_remove_hw(struct rt2x00_dev *rt2x00dev)
1091 if (test_bit(DEVICE_STATE_REGISTERED_HW, &rt2x00dev->flags))
1092 ieee80211_unregister_hw(rt2x00dev->hw);
1094 if (likely(rt2x00dev->hw->wiphy->bands[NL80211_BAND_2GHZ])) {
1095 kfree(rt2x00dev->hw->wiphy->bands[NL80211_BAND_2GHZ]->channels);
1096 kfree(rt2x00dev->hw->wiphy->bands[NL80211_BAND_2GHZ]->bitrates);
1097 rt2x00dev->hw->wiphy->bands[NL80211_BAND_2GHZ] = NULL;
1098 rt2x00dev->hw->wiphy->bands[NL80211_BAND_5GHZ] = NULL;
1101 kfree(rt2x00dev->spec.channels_info);
1104 static int rt2x00lib_probe_hw(struct rt2x00_dev *rt2x00dev)
1106 struct hw_mode_spec *spec = &rt2x00dev->spec;
1109 if (test_bit(DEVICE_STATE_REGISTERED_HW, &rt2x00dev->flags))
1113 * Initialize HW modes.
1115 status = rt2x00lib_probe_hw_modes(rt2x00dev, spec);
1120 * Initialize HW fields.
1122 rt2x00dev->hw->queues = rt2x00dev->ops->tx_queues;
1125 * Initialize extra TX headroom required.
1127 rt2x00dev->hw->extra_tx_headroom =
1128 max_t(unsigned int, IEEE80211_TX_STATUS_HEADROOM,
1129 rt2x00dev->extra_tx_headroom);
1132 * Take TX headroom required for alignment into account.
1134 if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_L2PAD))
1135 rt2x00dev->hw->extra_tx_headroom += RT2X00_L2PAD_SIZE;
1136 else if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_DMA))
1137 rt2x00dev->hw->extra_tx_headroom += RT2X00_ALIGN_SIZE;
1140 * Tell mac80211 about the size of our private STA structure.
1142 rt2x00dev->hw->sta_data_size = sizeof(struct rt2x00_sta);
1145 * Allocate tx status FIFO for driver use.
1147 if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_TXSTATUS_FIFO)) {
1149 * Allocate the txstatus fifo. In the worst case the tx
1150 * status fifo has to hold the tx status of all entries
1151 * in all tx queues. Hence, calculate the kfifo size as
1152 * tx_queues * entry_num and round up to the nearest
1156 roundup_pow_of_two(rt2x00dev->ops->tx_queues *
1157 rt2x00dev->tx->limit *
1160 status = kfifo_alloc(&rt2x00dev->txstatus_fifo, kfifo_size,
1167 * Initialize tasklets if used by the driver. Tasklets are
1168 * disabled until the interrupts are turned on. The driver
1169 * has to handle that.
1171 #define RT2X00_TASKLET_INIT(taskletname) \
1172 if (rt2x00dev->ops->lib->taskletname) { \
1173 tasklet_init(&rt2x00dev->taskletname, \
1174 rt2x00dev->ops->lib->taskletname, \
1175 (unsigned long)rt2x00dev); \
1178 RT2X00_TASKLET_INIT(txstatus_tasklet);
1179 RT2X00_TASKLET_INIT(pretbtt_tasklet);
1180 RT2X00_TASKLET_INIT(tbtt_tasklet);
1181 RT2X00_TASKLET_INIT(rxdone_tasklet);
1182 RT2X00_TASKLET_INIT(autowake_tasklet);
1184 #undef RT2X00_TASKLET_INIT
1189 status = ieee80211_register_hw(rt2x00dev->hw);
1193 set_bit(DEVICE_STATE_REGISTERED_HW, &rt2x00dev->flags);
1199 * Initialization/uninitialization handlers.
1201 static void rt2x00lib_uninitialize(struct rt2x00_dev *rt2x00dev)
1203 if (!test_and_clear_bit(DEVICE_STATE_INITIALIZED, &rt2x00dev->flags))
1207 * Stop rfkill polling.
1209 if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_DELAYED_RFKILL))
1210 rt2x00rfkill_unregister(rt2x00dev);
1213 * Allow the HW to uninitialize.
1215 rt2x00dev->ops->lib->uninitialize(rt2x00dev);
1218 * Free allocated queue entries.
1220 rt2x00queue_uninitialize(rt2x00dev);
1223 static int rt2x00lib_initialize(struct rt2x00_dev *rt2x00dev)
1227 if (test_bit(DEVICE_STATE_INITIALIZED, &rt2x00dev->flags))
1231 * Allocate all queue entries.
1233 status = rt2x00queue_initialize(rt2x00dev);
1238 * Initialize the device.
1240 status = rt2x00dev->ops->lib->initialize(rt2x00dev);
1242 rt2x00queue_uninitialize(rt2x00dev);
1246 set_bit(DEVICE_STATE_INITIALIZED, &rt2x00dev->flags);
1249 * Start rfkill polling.
1251 if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_DELAYED_RFKILL))
1252 rt2x00rfkill_register(rt2x00dev);
1257 int rt2x00lib_start(struct rt2x00_dev *rt2x00dev)
1261 if (test_bit(DEVICE_STATE_STARTED, &rt2x00dev->flags)) {
1263 * This is special case for ieee80211_restart_hw(), otherwise
1264 * mac80211 never call start() two times in row without stop();
1266 rt2x00dev->ops->lib->pre_reset_hw(rt2x00dev);
1267 rt2x00lib_stop(rt2x00dev);
1271 * If this is the first interface which is added,
1272 * we should load the firmware now.
1274 retval = rt2x00lib_load_firmware(rt2x00dev);
1279 * Initialize the device.
1281 retval = rt2x00lib_initialize(rt2x00dev);
1285 rt2x00dev->intf_ap_count = 0;
1286 rt2x00dev->intf_sta_count = 0;
1287 rt2x00dev->intf_associated = 0;
1289 /* Enable the radio */
1290 retval = rt2x00lib_enable_radio(rt2x00dev);
1294 set_bit(DEVICE_STATE_STARTED, &rt2x00dev->flags);
1299 void rt2x00lib_stop(struct rt2x00_dev *rt2x00dev)
1301 if (!test_and_clear_bit(DEVICE_STATE_STARTED, &rt2x00dev->flags))
1305 * Perhaps we can add something smarter here,
1306 * but for now just disabling the radio should do.
1308 rt2x00lib_disable_radio(rt2x00dev);
1310 rt2x00dev->intf_ap_count = 0;
1311 rt2x00dev->intf_sta_count = 0;
1312 rt2x00dev->intf_associated = 0;
1315 static inline void rt2x00lib_set_if_combinations(struct rt2x00_dev *rt2x00dev)
1317 struct ieee80211_iface_limit *if_limit;
1318 struct ieee80211_iface_combination *if_combination;
1320 if (rt2x00dev->ops->max_ap_intf < 2)
1324 * Build up AP interface limits structure.
1326 if_limit = &rt2x00dev->if_limits_ap;
1327 if_limit->max = rt2x00dev->ops->max_ap_intf;
1328 if_limit->types = BIT(NL80211_IFTYPE_AP);
1329 #ifdef CONFIG_MAC80211_MESH
1330 if_limit->types |= BIT(NL80211_IFTYPE_MESH_POINT);
1334 * Build up AP interface combinations structure.
1336 if_combination = &rt2x00dev->if_combinations[IF_COMB_AP];
1337 if_combination->limits = if_limit;
1338 if_combination->n_limits = 1;
1339 if_combination->max_interfaces = if_limit->max;
1340 if_combination->num_different_channels = 1;
1343 * Finally, specify the possible combinations to mac80211.
1345 rt2x00dev->hw->wiphy->iface_combinations = rt2x00dev->if_combinations;
1346 rt2x00dev->hw->wiphy->n_iface_combinations = 1;
1349 static unsigned int rt2x00dev_extra_tx_headroom(struct rt2x00_dev *rt2x00dev)
1351 if (WARN_ON(!rt2x00dev->tx))
1354 if (rt2x00_is_usb(rt2x00dev))
1355 return rt2x00dev->tx[0].winfo_size + rt2x00dev->tx[0].desc_size;
1357 return rt2x00dev->tx[0].winfo_size;
1361 * driver allocation handlers.
1363 int rt2x00lib_probe_dev(struct rt2x00_dev *rt2x00dev)
1365 int retval = -ENOMEM;
1368 * Set possible interface combinations.
1370 rt2x00lib_set_if_combinations(rt2x00dev);
1373 * Allocate the driver data memory, if necessary.
1375 if (rt2x00dev->ops->drv_data_size > 0) {
1376 rt2x00dev->drv_data = kzalloc(rt2x00dev->ops->drv_data_size,
1378 if (!rt2x00dev->drv_data) {
1384 spin_lock_init(&rt2x00dev->irqmask_lock);
1385 mutex_init(&rt2x00dev->csr_mutex);
1386 mutex_init(&rt2x00dev->conf_mutex);
1387 INIT_LIST_HEAD(&rt2x00dev->bar_list);
1388 spin_lock_init(&rt2x00dev->bar_list_lock);
1389 hrtimer_init(&rt2x00dev->txstatus_timer, CLOCK_MONOTONIC,
1392 set_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags);
1395 * Make room for rt2x00_intf inside the per-interface
1396 * structure ieee80211_vif.
1398 rt2x00dev->hw->vif_data_size = sizeof(struct rt2x00_intf);
1401 * rt2x00 devices can only use the last n bits of the MAC address
1402 * for virtual interfaces.
1404 rt2x00dev->hw->wiphy->addr_mask[ETH_ALEN - 1] =
1405 (rt2x00dev->ops->max_ap_intf - 1);
1410 rt2x00dev->workqueue =
1411 alloc_ordered_workqueue("%s", 0, wiphy_name(rt2x00dev->hw->wiphy));
1412 if (!rt2x00dev->workqueue) {
1417 INIT_WORK(&rt2x00dev->intf_work, rt2x00lib_intf_scheduled);
1418 INIT_DELAYED_WORK(&rt2x00dev->autowakeup_work, rt2x00lib_autowakeup);
1419 INIT_WORK(&rt2x00dev->sleep_work, rt2x00lib_sleep);
1422 * Let the driver probe the device to detect the capabilities.
1424 retval = rt2x00dev->ops->lib->probe_hw(rt2x00dev);
1426 rt2x00_err(rt2x00dev, "Failed to allocate device\n");
1431 * Allocate queue array.
1433 retval = rt2x00queue_allocate(rt2x00dev);
1437 /* Cache TX headroom value */
1438 rt2x00dev->extra_tx_headroom = rt2x00dev_extra_tx_headroom(rt2x00dev);
1441 * Determine which operating modes are supported, all modes
1442 * which require beaconing, depend on the availability of
1445 rt2x00dev->hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION);
1446 if (rt2x00dev->bcn->limit > 0)
1447 rt2x00dev->hw->wiphy->interface_modes |=
1448 BIT(NL80211_IFTYPE_ADHOC) |
1449 #ifdef CONFIG_MAC80211_MESH
1450 BIT(NL80211_IFTYPE_MESH_POINT) |
1452 #ifdef CONFIG_WIRELESS_WDS
1453 BIT(NL80211_IFTYPE_WDS) |
1455 BIT(NL80211_IFTYPE_AP);
1457 rt2x00dev->hw->wiphy->flags |= WIPHY_FLAG_IBSS_RSN;
1459 wiphy_ext_feature_set(rt2x00dev->hw->wiphy,
1460 NL80211_EXT_FEATURE_CQM_RSSI_LIST);
1463 * Initialize ieee80211 structure.
1465 retval = rt2x00lib_probe_hw(rt2x00dev);
1467 rt2x00_err(rt2x00dev, "Failed to initialize hw\n");
1472 * Register extra components.
1474 rt2x00link_register(rt2x00dev);
1475 rt2x00leds_register(rt2x00dev);
1476 rt2x00debug_register(rt2x00dev);
1479 * Start rfkill polling.
1481 if (!rt2x00_has_cap_flag(rt2x00dev, REQUIRE_DELAYED_RFKILL))
1482 rt2x00rfkill_register(rt2x00dev);
1487 rt2x00lib_remove_dev(rt2x00dev);
1491 EXPORT_SYMBOL_GPL(rt2x00lib_probe_dev);
1493 void rt2x00lib_remove_dev(struct rt2x00_dev *rt2x00dev)
1495 clear_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags);
1498 * Stop rfkill polling.
1500 if (!rt2x00_has_cap_flag(rt2x00dev, REQUIRE_DELAYED_RFKILL))
1501 rt2x00rfkill_unregister(rt2x00dev);
1506 rt2x00lib_disable_radio(rt2x00dev);
1511 cancel_work_sync(&rt2x00dev->intf_work);
1512 cancel_delayed_work_sync(&rt2x00dev->autowakeup_work);
1513 cancel_work_sync(&rt2x00dev->sleep_work);
1515 hrtimer_cancel(&rt2x00dev->txstatus_timer);
1518 * Kill the tx status tasklet.
1520 tasklet_kill(&rt2x00dev->txstatus_tasklet);
1521 tasklet_kill(&rt2x00dev->pretbtt_tasklet);
1522 tasklet_kill(&rt2x00dev->tbtt_tasklet);
1523 tasklet_kill(&rt2x00dev->rxdone_tasklet);
1524 tasklet_kill(&rt2x00dev->autowake_tasklet);
1527 * Uninitialize device.
1529 rt2x00lib_uninitialize(rt2x00dev);
1531 if (rt2x00dev->workqueue)
1532 destroy_workqueue(rt2x00dev->workqueue);
1535 * Free the tx status fifo.
1537 kfifo_free(&rt2x00dev->txstatus_fifo);
1540 * Free extra components
1542 rt2x00debug_deregister(rt2x00dev);
1543 rt2x00leds_unregister(rt2x00dev);
1546 * Free ieee80211_hw memory.
1548 rt2x00lib_remove_hw(rt2x00dev);
1551 * Free firmware image.
1553 rt2x00lib_free_firmware(rt2x00dev);
1556 * Free queue structures.
1558 rt2x00queue_free(rt2x00dev);
1561 * Free the driver data.
1563 kfree(rt2x00dev->drv_data);
1565 EXPORT_SYMBOL_GPL(rt2x00lib_remove_dev);
1568 * Device state handlers
1571 int rt2x00lib_suspend(struct rt2x00_dev *rt2x00dev, pm_message_t state)
1573 rt2x00_dbg(rt2x00dev, "Going to sleep\n");
1576 * Prevent mac80211 from accessing driver while suspended.
1578 if (!test_and_clear_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags))
1582 * Cleanup as much as possible.
1584 rt2x00lib_uninitialize(rt2x00dev);
1587 * Suspend/disable extra components.
1589 rt2x00leds_suspend(rt2x00dev);
1590 rt2x00debug_deregister(rt2x00dev);
1593 * Set device mode to sleep for power management,
1594 * on some hardware this call seems to consistently fail.
1595 * From the specifications it is hard to tell why it fails,
1596 * and if this is a "bad thing".
1597 * Overall it is safe to just ignore the failure and
1598 * continue suspending. The only downside is that the
1599 * device will not be in optimal power save mode, but with
1600 * the radio and the other components already disabled the
1601 * device is as good as disabled.
1603 if (rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_SLEEP))
1604 rt2x00_warn(rt2x00dev, "Device failed to enter sleep state, continue suspending\n");
1608 EXPORT_SYMBOL_GPL(rt2x00lib_suspend);
1610 int rt2x00lib_resume(struct rt2x00_dev *rt2x00dev)
1612 rt2x00_dbg(rt2x00dev, "Waking up\n");
1615 * Restore/enable extra components.
1617 rt2x00debug_register(rt2x00dev);
1618 rt2x00leds_resume(rt2x00dev);
1621 * We are ready again to receive requests from mac80211.
1623 set_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags);
1627 EXPORT_SYMBOL_GPL(rt2x00lib_resume);
1628 #endif /* CONFIG_PM */
1631 * rt2x00lib module information.
1633 MODULE_AUTHOR(DRV_PROJECT);
1634 MODULE_VERSION(DRV_VERSION);
1635 MODULE_DESCRIPTION("rt2x00 library");
1636 MODULE_LICENSE("GPL");