iwlwifi: pnvm: Fix a memory leak in 'iwl_pnvm_get_from_fs()'

[linux-2.6-microblaze.git] / drivers / net / wireless / intel / iwlwifi / iwl-prph.h

/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
/*
 * Copyright (C) 2005-2014, 2018-2021 Intel Corporation
 * Copyright (C) 2013-2015 Intel Mobile Communications GmbH
 * Copyright (C) 2016 Intel Deutschland GmbH
 */
#ifndef __iwl_prph_h__
#define __iwl_prph_h__
#include <linux/bitfield.h>

/*
 * Registers in this file are internal, not PCI bus memory mapped.
 * Driver accesses these via HBUS_TARG_PRPH_* registers.
 */
#define PRPH_BASE       (0x00000)
#define PRPH_END        (0xFFFFF)

/* APMG (power management) constants */
#define APMG_BASE                       (PRPH_BASE + 0x3000)
#define APMG_CLK_CTRL_REG               (APMG_BASE + 0x0000)
#define APMG_CLK_EN_REG                 (APMG_BASE + 0x0004)
#define APMG_CLK_DIS_REG                (APMG_BASE + 0x0008)
#define APMG_PS_CTRL_REG                (APMG_BASE + 0x000c)
#define APMG_PCIDEV_STT_REG             (APMG_BASE + 0x0010)
#define APMG_RFKILL_REG                 (APMG_BASE + 0x0014)
#define APMG_RTC_INT_STT_REG            (APMG_BASE + 0x001c)
#define APMG_RTC_INT_MSK_REG            (APMG_BASE + 0x0020)
#define APMG_DIGITAL_SVR_REG            (APMG_BASE + 0x0058)
#define APMG_ANALOG_SVR_REG             (APMG_BASE + 0x006C)

#define APMS_CLK_VAL_MRB_FUNC_MODE      (0x00000001)
#define APMG_CLK_VAL_DMA_CLK_RQT        (0x00000200)
#define APMG_CLK_VAL_BSM_CLK_RQT        (0x00000800)

#define APMG_PS_CTRL_EARLY_PWR_OFF_RESET_DIS    (0x00400000)
#define APMG_PS_CTRL_VAL_RESET_REQ              (0x04000000)
#define APMG_PS_CTRL_MSK_PWR_SRC                (0x03000000)
#define APMG_PS_CTRL_VAL_PWR_SRC_VMAIN          (0x00000000)
#define APMG_PS_CTRL_VAL_PWR_SRC_VAUX           (0x02000000)
#define APMG_SVR_VOLTAGE_CONFIG_BIT_MSK (0x000001E0) /* bit 8:5 */
#define APMG_SVR_DIGITAL_VOLTAGE_1_32           (0x00000060)

#define APMG_PCIDEV_STT_VAL_PERSIST_DIS (0x00000200)
#define APMG_PCIDEV_STT_VAL_L1_ACT_DIS  (0x00000800)
#define APMG_PCIDEV_STT_VAL_WAKE_ME     (0x00004000)

#define APMG_RTC_INT_STT_RFKILL         (0x10000000)

/* Device system time */
#define DEVICE_SYSTEM_TIME_REG 0xA0206C

/* Device NMI register and value for 8000 family and lower hw's */
#define DEVICE_SET_NMI_REG 0x00a01c30
#define DEVICE_SET_NMI_VAL_DRV BIT(7)
/* Device NMI register and value for 9000 family and above hw's */
#define UREG_NIC_SET_NMI_DRIVER 0x00a05c10
#define UREG_NIC_SET_NMI_DRIVER_NMI_FROM_DRIVER BIT(24)
#define UREG_NIC_SET_NMI_DRIVER_RESET_HANDSHAKE (BIT(24) | BIT(25))

/* Shared registers (0x0..0x3ff, via target indirect or periphery */
#define SHR_BASE        0x00a10000

/* Shared GP1 register */
#define SHR_APMG_GP1_REG                0x01dc
#define SHR_APMG_GP1_REG_PRPH           (SHR_BASE + SHR_APMG_GP1_REG)
#define SHR_APMG_GP1_WF_XTAL_LP_EN      0x00000004
#define SHR_APMG_GP1_CHICKEN_BIT_SELECT 0x80000000

/* Shared DL_CFG register */
#define SHR_APMG_DL_CFG_REG                     0x01c4
#define SHR_APMG_DL_CFG_REG_PRPH                (SHR_BASE + SHR_APMG_DL_CFG_REG)
#define SHR_APMG_DL_CFG_RTCS_CLK_SELECTOR_MSK   0x000000c0
#define SHR_APMG_DL_CFG_RTCS_CLK_INTERNAL_XTAL  0x00000080
#define SHR_APMG_DL_CFG_DL_CLOCK_POWER_UP       0x00000100

/* Shared APMG_XTAL_CFG register */
#define SHR_APMG_XTAL_CFG_REG           0x1c0
#define SHR_APMG_XTAL_CFG_XTAL_ON_REQ   0x80000000

/*
 * Device reset for family 8000
 * write to bit 24 in order to reset the CPU
*/
#define RELEASE_CPU_RESET               (0x300C)
#define RELEASE_CPU_RESET_BIT           BIT(24)

/*****************************************************************************
 *                        7000/3000 series SHR DTS addresses                 *
 *****************************************************************************/

#define SHR_MISC_WFM_DTS_EN     (0x00a10024)
#define DTSC_CFG_MODE           (0x00a10604)
#define DTSC_VREF_AVG           (0x00a10648)
#define DTSC_VREF5_AVG          (0x00a1064c)
#define DTSC_CFG_MODE_PERIODIC  (0x2)
#define DTSC_PTAT_AVG           (0x00a10650)


/**
 * Tx Scheduler
 *
 * The Tx Scheduler selects the next frame to be transmitted, choosing TFDs
 * (Transmit Frame Descriptors) from up to 16 circular Tx queues resident in
 * host DRAM.  It steers each frame's Tx command (which contains the frame
 * data) into one of up to 7 prioritized Tx DMA FIFO channels within the
 * device.  A queue maps to only one (selectable by driver) Tx DMA channel,
 * but one DMA channel may take input from several queues.
 *
 * Tx DMA FIFOs have dedicated purposes.
 *
 * For 5000 series and up, they are used differently
 * (cf. iwl5000_default_queue_to_tx_fifo in iwl-5000.c):
 *
 * 0 -- EDCA BK (background) frames, lowest priority
 * 1 -- EDCA BE (best effort) frames, normal priority
 * 2 -- EDCA VI (video) frames, higher priority
 * 3 -- EDCA VO (voice) and management frames, highest priority
 * 4 -- unused
 * 5 -- unused
 * 6 -- unused
 * 7 -- Commands
 *
 * Driver should normally map queues 0-6 to Tx DMA/FIFO channels 0-6.
 * In addition, driver can map the remaining queues to Tx DMA/FIFO
 * channels 0-3 to support 11n aggregation via EDCA DMA channels.
 *
 * The driver sets up each queue to work in one of two modes:
 *
 * 1)  Scheduler-Ack, in which the scheduler automatically supports a
 *     block-ack (BA) window of up to 64 TFDs.  In this mode, each queue
 *     contains TFDs for a unique combination of Recipient Address (RA)
 *     and Traffic Identifier (TID), that is, traffic of a given
 *     Quality-Of-Service (QOS) priority, destined for a single station.
 *
 *     In scheduler-ack mode, the scheduler keeps track of the Tx status of
 *     each frame within the BA window, including whether it's been transmitted,
 *     and whether it's been acknowledged by the receiving station.  The device
 *     automatically processes block-acks received from the receiving STA,
 *     and reschedules un-acked frames to be retransmitted (successful
 *     Tx completion may end up being out-of-order).
 *
 *     The driver must maintain the queue's Byte Count table in host DRAM
 *     for this mode.
 *     This mode does not support fragmentation.
 *
 * 2)  FIFO (a.k.a. non-Scheduler-ACK), in which each TFD is processed in order.
 *     The device may automatically retry Tx, but will retry only one frame
 *     at a time, until receiving ACK from receiving station, or reaching
 *     retry limit and giving up.
 *
 *     The command queue (#4/#9) must use this mode!
 *     This mode does not require use of the Byte Count table in host DRAM.
 *
 * Driver controls scheduler operation via 3 means:
 * 1)  Scheduler registers
 * 2)  Shared scheduler data base in internal SRAM
 * 3)  Shared data in host DRAM
 *
 * Initialization:
 *
 * When loading, driver should allocate memory for:
 * 1)  16 TFD circular buffers, each with space for (typically) 256 TFDs.
 * 2)  16 Byte Count circular buffers in 16 KBytes contiguous memory
 *     (1024 bytes for each queue).
 *
 * After receiving "Alive" response from uCode, driver must initialize
 * the scheduler (especially for queue #4/#9, the command queue, otherwise
 * the driver can't issue commands!):
 */
#define SCD_MEM_LOWER_BOUND             (0x0000)

/**
 * Max Tx window size is the max number of contiguous TFDs that the scheduler
 * can keep track of at one time when creating block-ack chains of frames.
 * Note that "64" matches the number of ack bits in a block-ack packet.
 */
#define SCD_WIN_SIZE                            64
#define SCD_FRAME_LIMIT                         64

#define SCD_TXFIFO_POS_TID                      (0)
#define SCD_TXFIFO_POS_RA                       (4)
#define SCD_QUEUE_RA_TID_MAP_RATID_MSK  (0x01FF)

/* agn SCD */
#define SCD_QUEUE_STTS_REG_POS_TXF      (0)
#define SCD_QUEUE_STTS_REG_POS_ACTIVE   (3)
#define SCD_QUEUE_STTS_REG_POS_WSL      (4)
#define SCD_QUEUE_STTS_REG_POS_SCD_ACT_EN (19)
#define SCD_QUEUE_STTS_REG_MSK          (0x017F0000)

#define SCD_QUEUE_CTX_REG1_CREDIT               (0x00FFFF00)
#define SCD_QUEUE_CTX_REG1_SUPER_CREDIT         (0xFF000000)
#define SCD_QUEUE_CTX_REG1_VAL(_n, _v)          FIELD_PREP(SCD_QUEUE_CTX_REG1_ ## _n, _v)

#define SCD_QUEUE_CTX_REG2_WIN_SIZE             (0x0000007F)
#define SCD_QUEUE_CTX_REG2_FRAME_LIMIT          (0x007F0000)
#define SCD_QUEUE_CTX_REG2_VAL(_n, _v)          FIELD_PREP(SCD_QUEUE_CTX_REG2_ ## _n, _v)

#define SCD_GP_CTRL_ENABLE_31_QUEUES            BIT(0)
#define SCD_GP_CTRL_AUTO_ACTIVE_MODE            BIT(18)

/* Context Data */
#define SCD_CONTEXT_MEM_LOWER_BOUND     (SCD_MEM_LOWER_BOUND + 0x600)
#define SCD_CONTEXT_MEM_UPPER_BOUND     (SCD_MEM_LOWER_BOUND + 0x6A0)

/* Tx status */
#define SCD_TX_STTS_MEM_LOWER_BOUND     (SCD_MEM_LOWER_BOUND + 0x6A0)
#define SCD_TX_STTS_MEM_UPPER_BOUND     (SCD_MEM_LOWER_BOUND + 0x7E0)

/* Translation Data */
#define SCD_TRANS_TBL_MEM_LOWER_BOUND   (SCD_MEM_LOWER_BOUND + 0x7E0)
#define SCD_TRANS_TBL_MEM_UPPER_BOUND   (SCD_MEM_LOWER_BOUND + 0x808)

#define SCD_CONTEXT_QUEUE_OFFSET(x)\
        (SCD_CONTEXT_MEM_LOWER_BOUND + ((x) * 8))

#define SCD_TX_STTS_QUEUE_OFFSET(x)\
        (SCD_TX_STTS_MEM_LOWER_BOUND + ((x) * 16))

#define SCD_TRANS_TBL_OFFSET_QUEUE(x) \
        ((SCD_TRANS_TBL_MEM_LOWER_BOUND + ((x) * 2)) & 0xfffc)

#define SCD_BASE                        (PRPH_BASE + 0xa02c00)

#define SCD_SRAM_BASE_ADDR      (SCD_BASE + 0x0)
#define SCD_DRAM_BASE_ADDR      (SCD_BASE + 0x8)
#define SCD_AIT                 (SCD_BASE + 0x0c)
#define SCD_TXFACT              (SCD_BASE + 0x10)
#define SCD_ACTIVE              (SCD_BASE + 0x14)
#define SCD_QUEUECHAIN_SEL      (SCD_BASE + 0xe8)
#define SCD_CHAINEXT_EN         (SCD_BASE + 0x244)
#define SCD_AGGR_SEL            (SCD_BASE + 0x248)
#define SCD_INTERRUPT_MASK      (SCD_BASE + 0x108)
#define SCD_GP_CTRL             (SCD_BASE + 0x1a8)
#define SCD_EN_CTRL             (SCD_BASE + 0x254)

/*********************** END TX SCHEDULER *************************************/

/* Oscillator clock */
#define OSC_CLK                         (0xa04068)
#define OSC_CLK_FORCE_CONTROL           (0x8)

#define FH_UCODE_LOAD_STATUS            (0x1AF0)

/*
 * Replacing FH_UCODE_LOAD_STATUS
 * This register is writen by driver and is read by uCode during boot flow.
 * Note this address is cleared after MAC reset.
 */
#define UREG_UCODE_LOAD_STATUS          (0xa05c40)
#define UREG_CPU_INIT_RUN               (0xa05c44)

#define LMPM_SECURE_UCODE_LOAD_CPU1_HDR_ADDR    (0x1E78)
#define LMPM_SECURE_UCODE_LOAD_CPU2_HDR_ADDR    (0x1E7C)

#define LMPM_SECURE_CPU1_HDR_MEM_SPACE          (0x420000)
#define LMPM_SECURE_CPU2_HDR_MEM_SPACE          (0x420400)

#define LMAC2_PRPH_OFFSET               (0x100000)

/* Rx FIFO */
#define RXF_SIZE_ADDR                   (0xa00c88)
#define RXF_RD_D_SPACE                  (0xa00c40)
#define RXF_RD_WR_PTR                   (0xa00c50)
#define RXF_RD_RD_PTR                   (0xa00c54)
#define RXF_RD_FENCE_PTR                (0xa00c4c)
#define RXF_SET_FENCE_MODE              (0xa00c14)
#define RXF_LD_WR2FENCE         (0xa00c1c)
#define RXF_FIFO_RD_FENCE_INC           (0xa00c68)
#define RXF_SIZE_BYTE_CND_POS           (7)
#define RXF_SIZE_BYTE_CNT_MSK           (0x3ff << RXF_SIZE_BYTE_CND_POS)
#define RXF_DIFF_FROM_PREV              (0x200)
#define RXF2C_DIFF_FROM_PREV            (0x4e00)

#define RXF_LD_FENCE_OFFSET_ADDR        (0xa00c10)
#define RXF_FIFO_RD_FENCE_ADDR          (0xa00c0c)

/* Tx FIFO */
#define TXF_FIFO_ITEM_CNT               (0xa00438)
#define TXF_WR_PTR                      (0xa00414)
#define TXF_RD_PTR                      (0xa00410)
#define TXF_FENCE_PTR                   (0xa00418)
#define TXF_LOCK_FENCE                  (0xa00424)
#define TXF_LARC_NUM                    (0xa0043c)
#define TXF_READ_MODIFY_DATA            (0xa00448)
#define TXF_READ_MODIFY_ADDR            (0xa0044c)

/* UMAC Internal Tx Fifo */
#define TXF_CPU2_FIFO_ITEM_CNT          (0xA00538)
#define TXF_CPU2_WR_PTR         (0xA00514)
#define TXF_CPU2_RD_PTR         (0xA00510)
#define TXF_CPU2_FENCE_PTR              (0xA00518)
#define TXF_CPU2_LOCK_FENCE             (0xA00524)
#define TXF_CPU2_NUM                    (0xA0053C)
#define TXF_CPU2_READ_MODIFY_DATA       (0xA00548)
#define TXF_CPU2_READ_MODIFY_ADDR       (0xA0054C)

/* Radio registers access */
#define RSP_RADIO_CMD                   (0xa02804)
#define RSP_RADIO_RDDAT                 (0xa02814)
#define RADIO_RSP_ADDR_POS              (6)
#define RADIO_RSP_RD_CMD                (3)

/* LTR control (Qu only) */
#define HPM_MAC_LTR_CSR                 0xa0348c
#define HPM_MAC_LRT_ENABLE_ALL          0xf
/* also uses CSR_LTR_* for values */
#define HPM_UMAC_LTR                    0xa03480

/* FW monitor */
#define MON_BUFF_SAMPLE_CTL             (0xa03c00)
#define MON_BUFF_BASE_ADDR              (0xa03c1c)
#define MON_BUFF_END_ADDR               (0xa03c40)
#define MON_BUFF_WRPTR                  (0xa03c44)
#define MON_BUFF_CYCLE_CNT              (0xa03c48)
/* FW monitor family 8000 and on */
#define MON_BUFF_BASE_ADDR_VER2         (0xa03c1c)
#define MON_BUFF_END_ADDR_VER2          (0xa03c20)
#define MON_BUFF_WRPTR_VER2             (0xa03c24)
#define MON_BUFF_CYCLE_CNT_VER2         (0xa03c28)
#define MON_BUFF_SHIFT_VER2             (0x8)
/* FW monitor familiy AX210 and on */
#define DBGC_CUR_DBGBUF_BASE_ADDR_LSB           (0xd03c20)
#define DBGC_CUR_DBGBUF_BASE_ADDR_MSB           (0xd03c24)
#define DBGC_CUR_DBGBUF_STATUS                  (0xd03c1c)
#define DBGC_DBGBUF_WRAP_AROUND                 (0xd03c2c)
#define DBGC_CUR_DBGBUF_STATUS_OFFSET_MSK       (0x00ffffff)
#define DBGC_CUR_DBGBUF_STATUS_IDX_MSK          (0x0f000000)

#define MON_DMARB_RD_CTL_ADDR           (0xa03c60)
#define MON_DMARB_RD_DATA_ADDR          (0xa03c5c)

#define DBGC_IN_SAMPLE                  (0xa03c00)
#define DBGC_OUT_CTRL                   (0xa03c0c)

/* M2S registers */
#define LDBG_M2S_BUF_WPTR                       (0xa0476c)
#define LDBG_M2S_BUF_WRAP_CNT                   (0xa04774)
#define LDBG_M2S_BUF_WPTR_VAL_MSK               (0x000fffff)
#define LDBG_M2S_BUF_WRAP_CNT_VAL_MSK           (0x000fffff)

/* enable the ID buf for read */
#define WFPM_PS_CTL_CLR                 0xA0300C
#define WFMP_MAC_ADDR_0                 0xA03080
#define WFMP_MAC_ADDR_1                 0xA03084
#define LMPM_PMG_EN                     0xA01CEC
#define RADIO_REG_SYS_MANUAL_DFT_0      0xAD4078
#define RFIC_REG_RD                     0xAD0470
#define WFPM_CTRL_REG                   0xA03030
#define WFPM_GP2                        0xA030B4

/* DBGI SRAM Register details */
#define DBGI_SRAM_TARGET_ACCESS_CFG                     0x00A2E14C
#define DBGI_SRAM_TARGET_ACCESS_CFG_RESET_ADDRESS_MSK   0x10000
#define DBGI_SRAM_TARGET_ACCESS_RDATA_LSB               0x00A2E154
#define DBGI_SRAM_TARGET_ACCESS_RDATA_MSB               0x00A2E158

enum {
        ENABLE_WFPM = BIT(31),
        WFPM_AUX_CTL_AUX_IF_MAC_OWNER_MSK       = 0x80000000,
};

#define CNVI_AUX_MISC_CHIP                              0xA200B0
#define CNVR_AUX_MISC_CHIP                              0xA2B800
#define CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM          0xA29890
#define CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR      0xA29938

#define PREG_AUX_BUS_WPROT_0            0xA04CC0

/* device family 9000 WPROT register */
#define PREG_PRPH_WPROT_9000            0xA04CE0
/* device family 22000 WPROT register */
#define PREG_PRPH_WPROT_22000           0xA04D00

#define SB_MODIFY_CFG_FLAG              0xA03088
#define SB_CPU_1_STATUS                 0xA01E30
#define SB_CPU_2_STATUS                 0xA01E34
#define UMAG_SB_CPU_1_STATUS            0xA038C0
#define UMAG_SB_CPU_2_STATUS            0xA038C4
#define UMAG_GEN_HW_STATUS              0xA038C8
#define UREG_UMAC_CURRENT_PC            0xa05c18
#define UREG_LMAC1_CURRENT_PC           0xa05c1c
#define UREG_LMAC2_CURRENT_PC           0xa05c20

/* For UMAG_GEN_HW_STATUS reg check */
enum {
        UMAG_GEN_HW_IS_FPGA = BIT(1),
};

/* FW chicken bits */
#define LMPM_CHICK                      0xA01FF8
enum {
        LMPM_CHICK_EXTENDED_ADDR_SPACE = BIT(0),
};

/* FW chicken bits */
#define LMPM_PAGE_PASS_NOTIF                    0xA03824
enum {
        LMPM_PAGE_PASS_NOTIF_POS = BIT(20),
};

#define UREG_CHICK              (0xA05C00)
#define UREG_CHICK_MSI_ENABLE   BIT(24)
#define UREG_CHICK_MSIX_ENABLE  BIT(25)

#define HPM_DEBUG                       0xA03440
#define PERSISTENCE_BIT                 BIT(12)
#define PREG_WFPM_ACCESS                BIT(12)

#define HPM_HIPM_GEN_CFG                        0xA03458
#define HPM_HIPM_GEN_CFG_CR_PG_EN               BIT(0)
#define HPM_HIPM_GEN_CFG_CR_SLP_EN              BIT(1)
#define HPM_HIPM_GEN_CFG_CR_FORCE_ACTIVE        BIT(10)

#define UREG_DOORBELL_TO_ISR6           0xA05C04
#define UREG_DOORBELL_TO_ISR6_NMI_BIT   BIT(0)
#define UREG_DOORBELL_TO_ISR6_RESET_HANDSHAKE (BIT(0) | BIT(1))
#define UREG_DOORBELL_TO_ISR6_SUSPEND   BIT(18)
#define UREG_DOORBELL_TO_ISR6_RESUME    BIT(19)
#define UREG_DOORBELL_TO_ISR6_PNVM      BIT(20)

#define CNVI_MBOX_C                     0xA3400C

#define FSEQ_ERROR_CODE                 0xA340C8
#define FSEQ_TOP_INIT_VERSION           0xA34038
#define FSEQ_CNVIO_INIT_VERSION         0xA3403C
#define FSEQ_OTP_VERSION                0xA340FC
#define FSEQ_TOP_CONTENT_VERSION        0xA340F4
#define FSEQ_ALIVE_TOKEN                0xA340F0
#define FSEQ_CNVI_ID                    0xA3408C
#define FSEQ_CNVR_ID                    0xA34090

#define IWL_D3_SLEEP_STATUS_SUSPEND     0xD3
#define IWL_D3_SLEEP_STATUS_RESUME      0xD0

#define WMAL_INDRCT_RD_CMD1_OPMOD_POS 28
#define WMAL_INDRCT_RD_CMD1_BYTE_ADDRESS_MSK 0xFFFFF
#define WMAL_CMD_READ_BURST_ACCESS 2
#define WMAL_MRSPF_1 0xADFC20
#define WMAL_INDRCT_RD_CMD1 0xADFD44
#define WMAL_INDRCT_CMD1 0xADFC14
#define WMAL_INDRCT_CMD(addr) \
        ((WMAL_CMD_READ_BURST_ACCESS << WMAL_INDRCT_RD_CMD1_OPMOD_POS) | \
         ((addr) & WMAL_INDRCT_RD_CMD1_BYTE_ADDRESS_MSK))

#define WFPM_LMAC1_PS_CTL_RW 0xA03380
#define WFPM_LMAC2_PS_CTL_RW 0xA033C0
#define WFPM_PS_CTL_RW_PHYRF_PD_FSM_CURSTATE_MSK 0x0000000F
#define WFPM_PHYRF_STATE_ON 5
#define HBUS_TIMEOUT 0xA5A5A5A1
#define WFPM_DPHY_OFF 0xDF10FF

#endif                          /* __iwl_prph_h__ */