drivers/net/phy/dp83822.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /* Driver for the Texas Instruments DP83822, DP83825 and DP83826 PHYs.
   3  *
   4  * Copyright (C) 2017 Texas Instruments Inc.
   5  */
   6
   7 #include <linux/ethtool.h>
   8 #include <linux/etherdevice.h>
   9 #include <linux/kernel.h>
  10 #include <linux/mii.h>
  11 #include <linux/module.h>
  12 #include <linux/of.h>
  13 #include <linux/phy.h>
  14 #include <linux/netdevice.h>
  15
  16 #define DP83822_PHY_ID          0x2000a240
  17 #define DP83825S_PHY_ID         0x2000a140
  18 #define DP83825I_PHY_ID         0x2000a150
  19 #define DP83825CM_PHY_ID        0x2000a160
  20 #define DP83825CS_PHY_ID        0x2000a170
  21 #define DP83826C_PHY_ID         0x2000a130
  22 #define DP83826NC_PHY_ID        0x2000a110
  23
  24 #define DP83822_DEVADDR         0x1f
  25
  26 #define MII_DP83822_CTRL_2      0x0a
  27 #define MII_DP83822_PHYSTS      0x10
  28 #define MII_DP83822_PHYSCR      0x11
  29 #define MII_DP83822_MISR1       0x12
  30 #define MII_DP83822_MISR2       0x13
  31 #define MII_DP83822_FCSCR       0x14
  32 #define MII_DP83822_RCSR        0x17
  33 #define MII_DP83822_RESET_CTRL  0x1f
  34 #define MII_DP83822_GENCFG      0x465
  35 #define MII_DP83822_SOR1        0x467
  36
  37 /* GENCFG */
  38 #define DP83822_SIG_DET_LOW     BIT(0)
  39
  40 /* Control Register 2 bits */
  41 #define DP83822_FX_ENABLE       BIT(14)
  42
  43 #define DP83822_HW_RESET        BIT(15)
  44 #define DP83822_SW_RESET        BIT(14)
  45
  46 /* PHY STS bits */
  47 #define DP83822_PHYSTS_DUPLEX                   BIT(2)
  48 #define DP83822_PHYSTS_10                       BIT(1)
  49 #define DP83822_PHYSTS_LINK                     BIT(0)
  50
  51 /* PHYSCR Register Fields */
  52 #define DP83822_PHYSCR_INT_OE           BIT(0) /* Interrupt Output Enable */
  53 #define DP83822_PHYSCR_INTEN            BIT(1) /* Interrupt Enable */
  54
  55 /* MISR1 bits */
  56 #define DP83822_RX_ERR_HF_INT_EN        BIT(0)
  57 #define DP83822_FALSE_CARRIER_HF_INT_EN BIT(1)
  58 #define DP83822_ANEG_COMPLETE_INT_EN    BIT(2)
  59 #define DP83822_DUP_MODE_CHANGE_INT_EN  BIT(3)
  60 #define DP83822_SPEED_CHANGED_INT_EN    BIT(4)
  61 #define DP83822_LINK_STAT_INT_EN        BIT(5)
  62 #define DP83822_ENERGY_DET_INT_EN       BIT(6)
  63 #define DP83822_LINK_QUAL_INT_EN        BIT(7)
  64
  65 /* MISR2 bits */
  66 #define DP83822_JABBER_DET_INT_EN       BIT(0)
  67 #define DP83822_WOL_PKT_INT_EN          BIT(1)
  68 #define DP83822_SLEEP_MODE_INT_EN       BIT(2)
  69 #define DP83822_MDI_XOVER_INT_EN        BIT(3)
  70 #define DP83822_LB_FIFO_INT_EN          BIT(4)
  71 #define DP83822_PAGE_RX_INT_EN          BIT(5)
  72 #define DP83822_ANEG_ERR_INT_EN         BIT(6)
  73 #define DP83822_EEE_ERROR_CHANGE_INT_EN BIT(7)
  74
  75 /* INT_STAT1 bits */
  76 #define DP83822_WOL_INT_EN      BIT(4)
  77 #define DP83822_WOL_INT_STAT    BIT(12)
  78
  79 #define MII_DP83822_RXSOP1      0x04a5
  80 #define MII_DP83822_RXSOP2      0x04a6
  81 #define MII_DP83822_RXSOP3      0x04a7
  82
  83 /* WoL Registers */
  84 #define MII_DP83822_WOL_CFG     0x04a0
  85 #define MII_DP83822_WOL_STAT    0x04a1
  86 #define MII_DP83822_WOL_DA1     0x04a2
  87 #define MII_DP83822_WOL_DA2     0x04a3
  88 #define MII_DP83822_WOL_DA3     0x04a4
  89
  90 /* WoL bits */
  91 #define DP83822_WOL_MAGIC_EN    BIT(0)
  92 #define DP83822_WOL_SECURE_ON   BIT(5)
  93 #define DP83822_WOL_EN          BIT(7)
  94 #define DP83822_WOL_INDICATION_SEL BIT(8)
  95 #define DP83822_WOL_CLR_INDICATION BIT(11)
  96
  97 /* RCSR bits */
  98 #define DP83822_RGMII_MODE_EN   BIT(9)
  99 #define DP83822_RX_CLK_SHIFT    BIT(12)
 100 #define DP83822_TX_CLK_SHIFT    BIT(11)
 101
 102 /* SOR1 mode */
 103 #define DP83822_STRAP_MODE1     0
 104 #define DP83822_STRAP_MODE2     BIT(0)
 105 #define DP83822_STRAP_MODE3     BIT(1)
 106 #define DP83822_STRAP_MODE4     GENMASK(1, 0)
 107
 108 #define DP83822_COL_STRAP_MASK  GENMASK(11, 10)
 109 #define DP83822_COL_SHIFT       10
 110 #define DP83822_RX_ER_STR_MASK  GENMASK(9, 8)
 111 #define DP83822_RX_ER_SHIFT     8
 112
 113 #define MII_DP83822_FIBER_ADVERTISE    (ADVERTISED_TP | ADVERTISED_MII | \
 114                                         ADVERTISED_FIBRE | \
 115                                         ADVERTISED_Pause | ADVERTISED_Asym_Pause)
 116
 117 struct dp83822_private {
 118         bool fx_signal_det_low;
 119         int fx_enabled;
 120         u16 fx_sd_enable;
 121 };
 122
 123 static int dp83822_set_wol(struct phy_device *phydev,
 124                            struct ethtool_wolinfo *wol)
 125 {
 126         struct net_device *ndev = phydev->attached_dev;
 127         u16 value;
 128         const u8 *mac;
 129
 130         if (wol->wolopts & (WAKE_MAGIC | WAKE_MAGICSECURE)) {
 131                 mac = (const u8 *)ndev->dev_addr;
 132
 133                 if (!is_valid_ether_addr(mac))
 134                         return -EINVAL;
 135
 136                 /* MAC addresses start with byte 5, but stored in mac[0].
 137                  * 822 PHYs store bytes 4|5, 2|3, 0|1
 138                  */
 139                 phy_write_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_DA1,
 140                               (mac[1] << 8) | mac[0]);
 141                 phy_write_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_DA2,
 142                               (mac[3] << 8) | mac[2]);
 143                 phy_write_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_DA3,
 144                               (mac[5] << 8) | mac[4]);
 145
 146                 value = phy_read_mmd(phydev, DP83822_DEVADDR,
 147                                      MII_DP83822_WOL_CFG);
 148                 if (wol->wolopts & WAKE_MAGIC)
 149                         value |= DP83822_WOL_MAGIC_EN;
 150                 else
 151                         value &= ~DP83822_WOL_MAGIC_EN;
 152
 153                 if (wol->wolopts & WAKE_MAGICSECURE) {
 154                         phy_write_mmd(phydev, DP83822_DEVADDR,
 155                                       MII_DP83822_RXSOP1,
 156                                       (wol->sopass[1] << 8) | wol->sopass[0]);
 157                         phy_write_mmd(phydev, DP83822_DEVADDR,
 158                                       MII_DP83822_RXSOP2,
 159                                       (wol->sopass[3] << 8) | wol->sopass[2]);
 160                         phy_write_mmd(phydev, DP83822_DEVADDR,
 161                                       MII_DP83822_RXSOP3,
 162                                       (wol->sopass[5] << 8) | wol->sopass[4]);
 163                         value |= DP83822_WOL_SECURE_ON;
 164                 } else {
 165                         value &= ~DP83822_WOL_SECURE_ON;
 166                 }
 167
 168                 /* Clear any pending WoL interrupt */
 169                 phy_read(phydev, MII_DP83822_MISR2);
 170
 171                 value |= DP83822_WOL_EN | DP83822_WOL_INDICATION_SEL |
 172                          DP83822_WOL_CLR_INDICATION;
 173
 174                 return phy_write_mmd(phydev, DP83822_DEVADDR,
 175                                      MII_DP83822_WOL_CFG, value);
 176         } else {
 177                 return phy_clear_bits_mmd(phydev, DP83822_DEVADDR,
 178                                           MII_DP83822_WOL_CFG, DP83822_WOL_EN);
 179         }
 180 }
 181
 182 static void dp83822_get_wol(struct phy_device *phydev,
 183                             struct ethtool_wolinfo *wol)
 184 {
 185         int value;
 186         u16 sopass_val;
 187
 188         wol->supported = (WAKE_MAGIC | WAKE_MAGICSECURE);
 189         wol->wolopts = 0;
 190
 191         value = phy_read_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_CFG);
 192
 193         if (value & DP83822_WOL_MAGIC_EN)
 194                 wol->wolopts |= WAKE_MAGIC;
 195
 196         if (value & DP83822_WOL_SECURE_ON) {
 197                 sopass_val = phy_read_mmd(phydev, DP83822_DEVADDR,
 198                                           MII_DP83822_RXSOP1);
 199                 wol->sopass[0] = (sopass_val & 0xff);
 200                 wol->sopass[1] = (sopass_val >> 8);
 201
 202                 sopass_val = phy_read_mmd(phydev, DP83822_DEVADDR,
 203                                           MII_DP83822_RXSOP2);
 204                 wol->sopass[2] = (sopass_val & 0xff);
 205                 wol->sopass[3] = (sopass_val >> 8);
 206
 207                 sopass_val = phy_read_mmd(phydev, DP83822_DEVADDR,
 208                                           MII_DP83822_RXSOP3);
 209                 wol->sopass[4] = (sopass_val & 0xff);
 210                 wol->sopass[5] = (sopass_val >> 8);
 211
 212                 wol->wolopts |= WAKE_MAGICSECURE;
 213         }
 214
 215         /* WoL is not enabled so set wolopts to 0 */
 216         if (!(value & DP83822_WOL_EN))
 217                 wol->wolopts = 0;
 218 }
 219
 220 static int dp83822_config_intr(struct phy_device *phydev)
 221 {
 222         struct dp83822_private *dp83822 = phydev->priv;
 223         int misr_status;
 224         int physcr_status;
 225         int err;
 226
 227         if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
 228                 misr_status = phy_read(phydev, MII_DP83822_MISR1);
 229                 if (misr_status < 0)
 230                         return misr_status;
 231
 232                 misr_status |= (DP83822_RX_ERR_HF_INT_EN |
 233                                 DP83822_FALSE_CARRIER_HF_INT_EN |
 234                                 DP83822_LINK_STAT_INT_EN |
 235                                 DP83822_ENERGY_DET_INT_EN |
 236                                 DP83822_LINK_QUAL_INT_EN);
 237
 238                 if (!dp83822->fx_enabled)
 239                         misr_status |= DP83822_ANEG_COMPLETE_INT_EN |
 240                                        DP83822_DUP_MODE_CHANGE_INT_EN |
 241                                        DP83822_SPEED_CHANGED_INT_EN;
 242
 243
 244                 err = phy_write(phydev, MII_DP83822_MISR1, misr_status);
 245                 if (err < 0)
 246                         return err;
 247
 248                 misr_status = phy_read(phydev, MII_DP83822_MISR2);
 249                 if (misr_status < 0)
 250                         return misr_status;
 251
 252                 misr_status |= (DP83822_JABBER_DET_INT_EN |
 253                                 DP83822_SLEEP_MODE_INT_EN |
 254                                 DP83822_LB_FIFO_INT_EN |
 255                                 DP83822_PAGE_RX_INT_EN |
 256                                 DP83822_EEE_ERROR_CHANGE_INT_EN);
 257
 258                 if (!dp83822->fx_enabled)
 259                         misr_status |= DP83822_MDI_XOVER_INT_EN |
 260                                        DP83822_ANEG_ERR_INT_EN |
 261                                        DP83822_WOL_PKT_INT_EN;
 262
 263                 err = phy_write(phydev, MII_DP83822_MISR2, misr_status);
 264                 if (err < 0)
 265                         return err;
 266
 267                 physcr_status = phy_read(phydev, MII_DP83822_PHYSCR);
 268                 if (physcr_status < 0)
 269                         return physcr_status;
 270
 271                 physcr_status |= DP83822_PHYSCR_INT_OE | DP83822_PHYSCR_INTEN;
 272
 273         } else {
 274                 err = phy_write(phydev, MII_DP83822_MISR1, 0);
 275                 if (err < 0)
 276                         return err;
 277
 278                 err = phy_write(phydev, MII_DP83822_MISR2, 0);
 279                 if (err < 0)
 280                         return err;
 281
 282                 physcr_status = phy_read(phydev, MII_DP83822_PHYSCR);
 283                 if (physcr_status < 0)
 284                         return physcr_status;
 285
 286                 physcr_status &= ~DP83822_PHYSCR_INTEN;
 287         }
 288
 289         return phy_write(phydev, MII_DP83822_PHYSCR, physcr_status);
 290 }
 291
 292 static irqreturn_t dp83822_handle_interrupt(struct phy_device *phydev)
 293 {
 294         bool trigger_machine = false;
 295         int irq_status;
 296
 297         /* The MISR1 and MISR2 registers are holding the interrupt status in
 298          * the upper half (15:8), while the lower half (7:0) is used for
 299          * controlling the interrupt enable state of those individual interrupt
 300          * sources. To determine the possible interrupt sources, just read the
 301          * MISR* register and use it directly to know which interrupts have
 302          * been enabled previously or not.
 303          */
 304         irq_status = phy_read(phydev, MII_DP83822_MISR1);
 305         if (irq_status < 0) {
 306                 phy_error(phydev);
 307                 return IRQ_NONE;
 308         }
 309         if (irq_status & ((irq_status & GENMASK(7, 0)) << 8))
 310                 trigger_machine = true;
 311
 312         irq_status = phy_read(phydev, MII_DP83822_MISR2);
 313         if (irq_status < 0) {
 314                 phy_error(phydev);
 315                 return IRQ_NONE;
 316         }
 317         if (irq_status & ((irq_status & GENMASK(7, 0)) << 8))
 318                 trigger_machine = true;
 319
 320         if (!trigger_machine)
 321                 return IRQ_NONE;
 322
 323         phy_trigger_machine(phydev);
 324
 325         return IRQ_HANDLED;
 326 }
 327
 328 static int dp8382x_disable_wol(struct phy_device *phydev)
 329 {
 330         return phy_clear_bits_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_CFG,
 331                                   DP83822_WOL_EN | DP83822_WOL_MAGIC_EN |
 332                                   DP83822_WOL_SECURE_ON);
 333 }
 334
 335 static int dp83822_read_status(struct phy_device *phydev)
 336 {
 337         struct dp83822_private *dp83822 = phydev->priv;
 338         int status = phy_read(phydev, MII_DP83822_PHYSTS);
 339         int ctrl2;
 340         int ret;
 341
 342         if (dp83822->fx_enabled) {
 343                 if (status & DP83822_PHYSTS_LINK) {
 344                         phydev->speed = SPEED_UNKNOWN;
 345                         phydev->duplex = DUPLEX_UNKNOWN;
 346                 } else {
 347                         ctrl2 = phy_read(phydev, MII_DP83822_CTRL_2);
 348                         if (ctrl2 < 0)
 349                                 return ctrl2;
 350
 351                         if (!(ctrl2 & DP83822_FX_ENABLE)) {
 352                                 ret = phy_write(phydev, MII_DP83822_CTRL_2,
 353                                                 DP83822_FX_ENABLE | ctrl2);
 354                                 if (ret < 0)
 355                                         return ret;
 356                         }
 357                 }
 358         }
 359
 360         ret = genphy_read_status(phydev);
 361         if (ret)
 362                 return ret;
 363
 364         if (status < 0)
 365                 return status;
 366
 367         if (status & DP83822_PHYSTS_DUPLEX)
 368                 phydev->duplex = DUPLEX_FULL;
 369         else
 370                 phydev->duplex = DUPLEX_HALF;
 371
 372         if (status & DP83822_PHYSTS_10)
 373                 phydev->speed = SPEED_10;
 374         else
 375                 phydev->speed = SPEED_100;
 376
 377         return 0;
 378 }
 379
 380 static int dp83822_config_init(struct phy_device *phydev)
 381 {
 382         struct dp83822_private *dp83822 = phydev->priv;
 383         struct device *dev = &phydev->mdio.dev;
 384         int rgmii_delay;
 385         s32 rx_int_delay;
 386         s32 tx_int_delay;
 387         int err = 0;
 388         int bmcr;
 389
 390         if (phy_interface_is_rgmii(phydev)) {
 391                 rx_int_delay = phy_get_internal_delay(phydev, dev, NULL, 0,
 392                                                       true);
 393
 394                 if (rx_int_delay <= 0)
 395                         rgmii_delay = 0;
 396                 else
 397                         rgmii_delay = DP83822_RX_CLK_SHIFT;
 398
 399                 tx_int_delay = phy_get_internal_delay(phydev, dev, NULL, 0,
 400                                                       false);
 401                 if (tx_int_delay <= 0)
 402                         rgmii_delay &= ~DP83822_TX_CLK_SHIFT;
 403                 else
 404                         rgmii_delay |= DP83822_TX_CLK_SHIFT;
 405
 406                 if (rgmii_delay) {
 407                         err = phy_set_bits_mmd(phydev, DP83822_DEVADDR,
 408                                                MII_DP83822_RCSR, rgmii_delay);
 409                         if (err)
 410                                 return err;
 411                 }
 412
 413                 phy_set_bits_mmd(phydev, DP83822_DEVADDR,
 414                                         MII_DP83822_RCSR, DP83822_RGMII_MODE_EN);
 415         } else {
 416                 phy_clear_bits_mmd(phydev, DP83822_DEVADDR,
 417                                         MII_DP83822_RCSR, DP83822_RGMII_MODE_EN);
 418         }
 419
 420         if (dp83822->fx_enabled) {
 421                 err = phy_modify(phydev, MII_DP83822_CTRL_2,
 422                                  DP83822_FX_ENABLE, 1);
 423                 if (err < 0)
 424                         return err;
 425
 426                 /* Only allow advertising what this PHY supports */
 427                 linkmode_and(phydev->advertising, phydev->advertising,
 428                              phydev->supported);
 429
 430                 linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT,
 431                                  phydev->supported);
 432                 linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT,
 433                                  phydev->advertising);
 434                 linkmode_set_bit(ETHTOOL_LINK_MODE_100baseFX_Full_BIT,
 435                                  phydev->supported);
 436                 linkmode_set_bit(ETHTOOL_LINK_MODE_100baseFX_Half_BIT,
 437                                  phydev->supported);
 438                 linkmode_set_bit(ETHTOOL_LINK_MODE_100baseFX_Full_BIT,
 439                                  phydev->advertising);
 440                 linkmode_set_bit(ETHTOOL_LINK_MODE_100baseFX_Half_BIT,
 441                                  phydev->advertising);
 442
 443                 /* Auto neg is not supported in fiber mode */
 444                 bmcr = phy_read(phydev, MII_BMCR);
 445                 if (bmcr < 0)
 446                         return bmcr;
 447
 448                 if (bmcr & BMCR_ANENABLE) {
 449                         err =  phy_modify(phydev, MII_BMCR, BMCR_ANENABLE, 0);
 450                         if (err < 0)
 451                                 return err;
 452                 }
 453                 phydev->autoneg = AUTONEG_DISABLE;
 454                 linkmode_clear_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
 455                                    phydev->supported);
 456                 linkmode_clear_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
 457                                    phydev->advertising);
 458
 459                 /* Setup fiber advertisement */
 460                 err = phy_modify_changed(phydev, MII_ADVERTISE,
 461                                          MII_DP83822_FIBER_ADVERTISE,
 462                                          MII_DP83822_FIBER_ADVERTISE);
 463
 464                 if (err < 0)
 465                         return err;
 466
 467                 if (dp83822->fx_signal_det_low) {
 468                         err = phy_set_bits_mmd(phydev, DP83822_DEVADDR,
 469                                                MII_DP83822_GENCFG,
 470                                                DP83822_SIG_DET_LOW);
 471                         if (err)
 472                                 return err;
 473                 }
 474         }
 475         return dp8382x_disable_wol(phydev);
 476 }
 477
 478 static int dp8382x_config_init(struct phy_device *phydev)
 479 {
 480         return dp8382x_disable_wol(phydev);
 481 }
 482
 483 static int dp83822_phy_reset(struct phy_device *phydev)
 484 {
 485         int err;
 486
 487         err = phy_write(phydev, MII_DP83822_RESET_CTRL, DP83822_SW_RESET);
 488         if (err < 0)
 489                 return err;
 490
 491         return phydev->drv->config_init(phydev);
 492 }
 493
 494 #ifdef CONFIG_OF_MDIO
 495 static int dp83822_of_init(struct phy_device *phydev)
 496 {
 497         struct dp83822_private *dp83822 = phydev->priv;
 498         struct device *dev = &phydev->mdio.dev;
 499
 500         /* Signal detection for the PHY is only enabled if the FX_EN and the
 501          * SD_EN pins are strapped. Signal detection can only enabled if FX_EN
 502          * is strapped otherwise signal detection is disabled for the PHY.
 503          */
 504         if (dp83822->fx_enabled && dp83822->fx_sd_enable)
 505                 dp83822->fx_signal_det_low = device_property_present(dev,
 506                                                                      "ti,link-loss-low");
 507         if (!dp83822->fx_enabled)
 508                 dp83822->fx_enabled = device_property_present(dev,
 509                                                               "ti,fiber-mode");
 510
 511         return 0;
 512 }
 513 #else
 514 static int dp83822_of_init(struct phy_device *phydev)
 515 {
 516         return 0;
 517 }
 518 #endif /* CONFIG_OF_MDIO */
 519
 520 static int dp83822_read_straps(struct phy_device *phydev)
 521 {
 522         struct dp83822_private *dp83822 = phydev->priv;
 523         int fx_enabled, fx_sd_enable;
 524         int val;
 525
 526         val = phy_read_mmd(phydev, DP83822_DEVADDR, MII_DP83822_SOR1);
 527         if (val < 0)
 528                 return val;
 529
 530         fx_enabled = (val & DP83822_COL_STRAP_MASK) >> DP83822_COL_SHIFT;
 531         if (fx_enabled == DP83822_STRAP_MODE2 ||
 532             fx_enabled == DP83822_STRAP_MODE3)
 533                 dp83822->fx_enabled = 1;
 534
 535         if (dp83822->fx_enabled) {
 536                 fx_sd_enable = (val & DP83822_RX_ER_STR_MASK) >> DP83822_RX_ER_SHIFT;
 537                 if (fx_sd_enable == DP83822_STRAP_MODE3 ||
 538                     fx_sd_enable == DP83822_STRAP_MODE4)
 539                         dp83822->fx_sd_enable = 1;
 540         }
 541
 542         return 0;
 543 }
 544
 545 static int dp83822_probe(struct phy_device *phydev)
 546 {
 547         struct dp83822_private *dp83822;
 548         int ret;
 549
 550         dp83822 = devm_kzalloc(&phydev->mdio.dev, sizeof(*dp83822),
 551                                GFP_KERNEL);
 552         if (!dp83822)
 553                 return -ENOMEM;
 554
 555         phydev->priv = dp83822;
 556
 557         ret = dp83822_read_straps(phydev);
 558         if (ret)
 559                 return ret;
 560
 561         dp83822_of_init(phydev);
 562
 563         if (dp83822->fx_enabled)
 564                 phydev->port = PORT_FIBRE;
 565
 566         return 0;
 567 }
 568
 569 static int dp83822_suspend(struct phy_device *phydev)
 570 {
 571         int value;
 572
 573         value = phy_read_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_CFG);
 574
 575         if (!(value & DP83822_WOL_EN))
 576                 genphy_suspend(phydev);
 577
 578         return 0;
 579 }
 580
 581 static int dp83822_resume(struct phy_device *phydev)
 582 {
 583         int value;
 584
 585         genphy_resume(phydev);
 586
 587         value = phy_read_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_CFG);
 588
 589         phy_write_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_CFG, value |
 590                       DP83822_WOL_CLR_INDICATION);
 591
 592         return 0;
 593 }
 594
 595 #define DP83822_PHY_DRIVER(_id, _name)                          \
 596         {                                                       \
 597                 PHY_ID_MATCH_MODEL(_id),                        \
 598                 .name           = (_name),                      \
 599                 /* PHY_BASIC_FEATURES */                        \
 600                 .probe          = dp83822_probe,                \
 601                 .soft_reset     = dp83822_phy_reset,            \
 602                 .config_init    = dp83822_config_init,          \
 603                 .read_status    = dp83822_read_status,          \
 604                 .get_wol = dp83822_get_wol,                     \
 605                 .set_wol = dp83822_set_wol,                     \
 606                 .config_intr = dp83822_config_intr,             \
 607                 .handle_interrupt = dp83822_handle_interrupt,   \
 608                 .suspend = dp83822_suspend,                     \
 609                 .resume = dp83822_resume,                       \
 610         }
 611
 612 #define DP8382X_PHY_DRIVER(_id, _name)                          \
 613         {                                                       \
 614                 PHY_ID_MATCH_MODEL(_id),                        \
 615                 .name           = (_name),                      \
 616                 /* PHY_BASIC_FEATURES */                        \
 617                 .soft_reset     = dp83822_phy_reset,            \
 618                 .config_init    = dp8382x_config_init,          \
 619                 .get_wol = dp83822_get_wol,                     \
 620                 .set_wol = dp83822_set_wol,                     \
 621                 .config_intr = dp83822_config_intr,             \
 622                 .handle_interrupt = dp83822_handle_interrupt,   \
 623                 .suspend = dp83822_suspend,                     \
 624                 .resume = dp83822_resume,                       \
 625         }
 626
 627 static struct phy_driver dp83822_driver[] = {
 628         DP83822_PHY_DRIVER(DP83822_PHY_ID, "TI DP83822"),
 629         DP8382X_PHY_DRIVER(DP83825I_PHY_ID, "TI DP83825I"),
 630         DP8382X_PHY_DRIVER(DP83826C_PHY_ID, "TI DP83826C"),
 631         DP8382X_PHY_DRIVER(DP83826NC_PHY_ID, "TI DP83826NC"),
 632         DP8382X_PHY_DRIVER(DP83825S_PHY_ID, "TI DP83825S"),
 633         DP8382X_PHY_DRIVER(DP83825CM_PHY_ID, "TI DP83825M"),
 634         DP8382X_PHY_DRIVER(DP83825CS_PHY_ID, "TI DP83825CS"),
 635 };
 636 module_phy_driver(dp83822_driver);
 637
 638 static struct mdio_device_id __maybe_unused dp83822_tbl[] = {
 639         { DP83822_PHY_ID, 0xfffffff0 },
 640         { DP83825I_PHY_ID, 0xfffffff0 },
 641         { DP83826C_PHY_ID, 0xfffffff0 },
 642         { DP83826NC_PHY_ID, 0xfffffff0 },
 643         { DP83825S_PHY_ID, 0xfffffff0 },
 644         { DP83825CM_PHY_ID, 0xfffffff0 },
 645         { DP83825CS_PHY_ID, 0xfffffff0 },
 646         { },
 647 };
 648 MODULE_DEVICE_TABLE(mdio, dp83822_tbl);
 649
 650 MODULE_DESCRIPTION("Texas Instruments DP83822 PHY driver");
 651 MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com");
 652 MODULE_LICENSE("GPL v2");