1 /* SPDX-License-Identifier: GPL-2.0 */
3 /* Copyright (c) 2012-2018, The Linux Foundation. All rights reserved.
4 * Copyright (C) 2018-2020 Linaro Ltd.
9 #include <linux/types.h>
10 #include <linux/device.h>
11 #include <linux/notifier.h>
12 #include <linux/pm_wakeup.h>
14 #include "ipa_version.h"
18 #include "ipa_endpoint.h"
19 #include "ipa_interrupt.h"
24 struct platform_device;
31 * struct ipa - IPA information
32 * @gsi: Embedded GSI structure
33 * @version: IPA hardware version
34 * @pdev: Platform device
35 * @completion: Used to signal pipeline clear transfer complete
36 * @nb: Notifier block used for remoteproc SSR
37 * @notifier: Remoteproc SSR notifier
38 * @smp2p: SMP2P information
39 * @power: IPA power information
40 * @table_addr: DMA address of filter/route table content
41 * @table_virt: Virtual address of filter/route table content
42 * @interrupt: IPA Interrupt information
43 * @uc_powered: true if power is active by proxy for microcontroller
44 * @uc_loaded: true after microcontroller has reported it's ready
45 * @reg_addr: DMA address used for IPA register access
46 * @reg_virt: Virtual address used for IPA register access
47 * @mem_addr: DMA address of IPA-local memory space
48 * @mem_virt: Virtual address of IPA-local memory space
49 * @mem_offset: Offset from @mem_virt used for access to IPA memory
50 * @mem_size: Total size (bytes) of memory at @mem_virt
51 * @mem_count: Number of entries in the mem array
52 * @mem: Array of IPA-local memory region descriptors
53 * @imem_iova: I/O virtual address of IPA region in IMEM
54 * @imem_size: Size of IMEM region
55 * @smem_iova: I/O virtual address of IPA region in SMEM
56 * @smem_size: Size of SMEM region
57 * @zero_addr: DMA address of preallocated zero-filled memory
58 * @zero_virt: Virtual address of preallocated zero-filled memory
59 * @zero_size: Size (bytes) of preallocated zero-filled memory
60 * @available: Bit mask indicating endpoints hardware supports
61 * @filter_map: Bit mask indicating endpoints that support filtering
62 * @initialized: Bit mask indicating endpoints initialized
63 * @set_up: Bit mask indicating endpoints set up
64 * @enabled: Bit mask indicating endpoints enabled
65 * @modem_tx_count: Number of defined modem TX endoints
66 * @endpoint: Array of endpoint information
67 * @channel_map: Mapping of GSI channel to IPA endpoint
68 * @name_map: Mapping of IPA endpoint name to IPA endpoint
69 * @setup_complete: Flag indicating whether setup stage has completed
70 * @modem_state: State of modem (stopped, running)
71 * @modem_netdev: Network device structure used for modem
72 * @qmi: QMI information
76 enum ipa_version version;
77 struct platform_device *pdev;
78 struct completion completion;
79 struct notifier_block nb;
81 struct ipa_smp2p *smp2p;
82 struct ipa_power *power;
84 dma_addr_t table_addr;
87 struct ipa_interrupt *interrupt;
92 void __iomem *reg_virt;
99 const struct ipa_mem *mem;
101 unsigned long imem_iova;
104 unsigned long smem_iova;
107 dma_addr_t zero_addr;
111 /* Bit masks indicating endpoint state */
112 u32 available; /* supported by hardware */
119 struct ipa_endpoint endpoint[IPA_ENDPOINT_MAX];
120 struct ipa_endpoint *channel_map[GSI_CHANNEL_COUNT_MAX];
121 struct ipa_endpoint *name_map[IPA_ENDPOINT_COUNT];
125 atomic_t modem_state; /* enum ipa_modem_state */
126 struct net_device *modem_netdev;
131 * ipa_setup() - Perform IPA setup
134 * IPA initialization is broken into stages: init; config; and setup.
135 * (These have inverses exit, deconfig, and teardown.)
137 * Activities performed at the init stage can be done without requiring
138 * any access to IPA hardware. Activities performed at the config stage
139 * require IPA power, because they involve access to IPA registers.
140 * The setup stage is performed only after the GSI hardware is ready
141 * (more on this below). The setup stage allows the AP to perform
142 * more complex initialization by issuing "immediate commands" using
143 * a special interface to the IPA.
145 * This function, @ipa_setup(), starts the setup stage.
147 * In order for the GSI hardware to be functional it needs firmware to be
148 * loaded (in addition to some other low-level initialization). This early
149 * GSI initialization can be done either by Trust Zone on the AP or by the
152 * If it's done by Trust Zone, the AP loads the GSI firmware and supplies
153 * it to Trust Zone to verify and install. When this completes, if
154 * verification was successful, the GSI layer is ready and ipa_setup()
155 * implements the setup phase of initialization.
157 * If the modem performs early GSI initialization, the AP needs to know
158 * when this has occurred. An SMP2P interrupt is used for this purpose,
159 * and receipt of that interrupt triggers the call to ipa_setup().
161 int ipa_setup(struct ipa *ipa);