Linux 6.9-rc1
[linux-2.6-microblaze.git] / drivers / net / arcnet / Kconfig
1 # SPDX-License-Identifier: GPL-2.0-only
2 #
3 # Arcnet configuration
4 #
5
6 menuconfig ARCNET
7         depends on NETDEVICES && (ISA || PCI || PCMCIA)
8         tristate "ARCnet support"
9         help
10           If you have a network card of this type, say Y and check out the
11           (arguably) beautiful poetry in
12           <file:Documentation/networking/arcnet.rst>.
13
14           You need both this driver, and the driver for the particular ARCnet
15           chipset of your card. If you don't know, then it's probably a
16           COM90xx type card, so say Y (or M) to "ARCnet COM90xx chipset
17           support" below.
18
19           To compile this driver as a module, choose M here. The module will
20           be called arcnet.
21
22 if ARCNET
23
24 config ARCNET_1201
25         tristate "Enable standard ARCNet packet format (RFC 1201)"
26         help
27           This allows you to use RFC1201 with your ARCnet card via the virtual
28           arc0 device.  You need to say Y here to communicate with
29           industry-standard RFC1201 implementations, like the arcether.com
30           packet driver or most DOS/Windows ODI drivers.  Please read the
31           ARCnet documentation in <file:Documentation/networking/arcnet.rst>
32           for more information about using arc0.
33
34 config ARCNET_1051
35         tristate "Enable old ARCNet packet format (RFC 1051)"
36         help
37           This allows you to use RFC1051 with your ARCnet card via the virtual
38           arc0s device. You only need arc0s if you want to talk to ARCnet
39           software complying with the "old" standard, specifically, the DOS
40           arcnet.com packet driver, Amigas running AmiTCP, and some variants
41           of NetBSD. You do not need to say Y here to communicate with
42           industry-standard RFC1201 implementations, like the arcether.com
43           packet driver or most DOS/Windows ODI drivers. RFC1201 is included
44           automatically as the arc0 device. Please read the ARCnet
45           documentation in <file:Documentation/networking/arcnet.rst> for more
46           information about using arc0e and arc0s.
47
48 config ARCNET_RAW
49         tristate "Enable raw mode packet interface"
50         help
51           ARCnet "raw mode" packet encapsulation, no soft headers.  Unlikely
52           to work unless talking to a copy of the same Linux arcnet driver,
53           but perhaps marginally faster in that case.
54
55 config ARCNET_CAP
56         tristate "Enable CAP mode packet interface"
57         help
58           ARCnet "cap mode" packet encapsulation. Used to get the hardware
59           acknowledge back to userspace. After the initial protocol byte every
60           packet is stuffed with an extra 4 byte "cookie" which doesn't
61           actually appear on the network. After transmit the driver will send
62           back a packet with protocol byte 0 containing the status of the
63           transmission:
64              0=no hardware acknowledge
65              1=excessive nak
66              2=transmission accepted by the receiver hardware
67
68           Received packets are also stuffed with the extra 4 bytes but it will
69           be random data.
70
71           Cap only listens to protocol 1-8.
72
73 config ARCNET_COM90xx
74         tristate "ARCnet COM90xx (normal) chipset driver"
75         help
76           This is the chipset driver for the standard COM90xx cards. If you
77           have always used the old ARCnet driver without knowing what type of
78           card you had, this is probably the one for you.
79
80           To compile this driver as a module, choose M here. The module will
81           be called com90xx.
82
83 config ARCNET_COM90xxIO
84         tristate "ARCnet COM90xx (IO mapped) chipset driver"
85         help
86           This is the chipset driver for the COM90xx cards, using them in
87           IO-mapped mode instead of memory-mapped mode. This is slower than
88           the normal driver. Only use it if your card doesn't support shared
89           memory.
90
91           To compile this driver as a module, choose M here. The module will
92           be called com90io.
93
94 config ARCNET_RIM_I
95         tristate "ARCnet COM90xx (RIM I) chipset driver"
96         help
97           This is yet another chipset driver for the COM90xx cards, but this
98           time only using memory-mapped mode, and no IO ports at all. This
99           driver is completely untested, so if you have one of these cards,
100           please mail <dwmw2@infradead.org>, especially if it works!
101
102           To compile this driver as a module, choose M here. The module will
103           be called arc-rimi.
104
105 config ARCNET_COM20020
106         tristate "ARCnet COM20020 chipset driver"
107         depends on LEDS_CLASS
108         help
109           This is the driver for the new COM20020 chipset. It supports such
110           things as promiscuous mode, so packet sniffing is possible, and
111           extra diagnostic information.
112
113           To compile this driver as a module, choose M here. The module will
114           be called com20020.
115
116 config ARCNET_COM20020_ISA
117         tristate "Support for COM20020 on ISA"
118         depends on ARCNET_COM20020 && ISA
119
120 config ARCNET_COM20020_PCI
121         tristate "Support for COM20020 on PCI"
122         depends on ARCNET_COM20020 && PCI
123
124 config ARCNET_COM20020_CS
125         tristate "COM20020 ARCnet PCMCIA support"
126         depends on ARCNET_COM20020 && PCMCIA
127         help
128           Say Y here if you intend to attach this type of ARCnet PCMCIA card
129           to your computer.
130
131           To compile this driver as a module, choose M here: the module will be
132           called com20020_cs.  If unsure, say N.
133
134 endif # ARCNET