drivers/mmc/host/sdhci-sprd.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 //
   3 // Secure Digital Host Controller
   4 //
   5 // Copyright (C) 2018 Spreadtrum, Inc.
   6 // Author: Chunyan Zhang <chunyan.zhang@unisoc.com>
   7
   8 #include <linux/delay.h>
   9 #include <linux/dma-mapping.h>
  10 #include <linux/highmem.h>
  11 #include <linux/module.h>
  12 #include <linux/of.h>
  13 #include <linux/of_device.h>
  14 #include <linux/of_gpio.h>
  15 #include <linux/pinctrl/consumer.h>
  16 #include <linux/platform_device.h>
  17 #include <linux/pm_runtime.h>
  18 #include <linux/regulator/consumer.h>
  19 #include <linux/slab.h>
  20
  21 #include "sdhci-pltfm.h"
  22 #include "mmc_hsq.h"
  23
  24 /* SDHCI_ARGUMENT2 register high 16bit */
  25 #define SDHCI_SPRD_ARG2_STUFF           GENMASK(31, 16)
  26
  27 #define SDHCI_SPRD_REG_32_DLL_CFG       0x200
  28 #define  SDHCI_SPRD_DLL_ALL_CPST_EN     (BIT(18) | BIT(24) | BIT(25) | BIT(26) | BIT(27))
  29 #define  SDHCI_SPRD_DLL_EN              BIT(21)
  30 #define  SDHCI_SPRD_DLL_SEARCH_MODE     BIT(16)
  31 #define  SDHCI_SPRD_DLL_INIT_COUNT      0xc00
  32 #define  SDHCI_SPRD_DLL_PHASE_INTERNAL  0x3
  33
  34 #define SDHCI_SPRD_REG_32_DLL_DLY       0x204
  35
  36 #define SDHCI_SPRD_REG_32_DLL_DLY_OFFSET        0x208
  37 #define  SDHCIBSPRD_IT_WR_DLY_INV               BIT(5)
  38 #define  SDHCI_SPRD_BIT_CMD_DLY_INV             BIT(13)
  39 #define  SDHCI_SPRD_BIT_POSRD_DLY_INV           BIT(21)
  40 #define  SDHCI_SPRD_BIT_NEGRD_DLY_INV           BIT(29)
  41
  42 #define SDHCI_SPRD_REG_32_BUSY_POSI             0x250
  43 #define  SDHCI_SPRD_BIT_OUTR_CLK_AUTO_EN        BIT(25)
  44 #define  SDHCI_SPRD_BIT_INNR_CLK_AUTO_EN        BIT(24)
  45
  46 #define SDHCI_SPRD_REG_DEBOUNCE         0x28C
  47 #define  SDHCI_SPRD_BIT_DLL_BAK         BIT(0)
  48 #define  SDHCI_SPRD_BIT_DLL_VAL         BIT(1)
  49
  50 #define  SDHCI_SPRD_INT_SIGNAL_MASK     0x1B7F410B
  51
  52 /* SDHCI_HOST_CONTROL2 */
  53 #define  SDHCI_SPRD_CTRL_HS200          0x0005
  54 #define  SDHCI_SPRD_CTRL_HS400          0x0006
  55 #define  SDHCI_SPRD_CTRL_HS400ES        0x0007
  56
  57 /*
  58  * According to the standard specification, BIT(3) of SDHCI_SOFTWARE_RESET is
  59  * reserved, and only used on Spreadtrum's design, the hardware cannot work
  60  * if this bit is cleared.
  61  * 1 : normal work
  62  * 0 : hardware reset
  63  */
  64 #define  SDHCI_HW_RESET_CARD            BIT(3)
  65
  66 #define SDHCI_SPRD_MAX_CUR              0xFFFFFF
  67 #define SDHCI_SPRD_CLK_MAX_DIV          1023
  68
  69 #define SDHCI_SPRD_CLK_DEF_RATE         26000000
  70 #define SDHCI_SPRD_PHY_DLL_CLK          52000000
  71
  72 struct sdhci_sprd_host {
  73         u32 version;
  74         struct clk *clk_sdio;
  75         struct clk *clk_enable;
  76         struct clk *clk_2x_enable;
  77         struct pinctrl *pinctrl;
  78         struct pinctrl_state *pins_uhs;
  79         struct pinctrl_state *pins_default;
  80         u32 base_rate;
  81         int flags; /* backup of host attribute */
  82         u32 phy_delay[MMC_TIMING_MMC_HS400 + 2];
  83 };
  84
  85 struct sdhci_sprd_phy_cfg {
  86         const char *property;
  87         u8 timing;
  88 };
  89
  90 static const struct sdhci_sprd_phy_cfg sdhci_sprd_phy_cfgs[] = {
  91         { "sprd,phy-delay-legacy", MMC_TIMING_LEGACY, },
  92         { "sprd,phy-delay-sd-highspeed", MMC_TIMING_SD_HS, },
  93         { "sprd,phy-delay-sd-uhs-sdr50", MMC_TIMING_UHS_SDR50, },
  94         { "sprd,phy-delay-sd-uhs-sdr104", MMC_TIMING_UHS_SDR104, },
  95         { "sprd,phy-delay-mmc-highspeed", MMC_TIMING_MMC_HS, },
  96         { "sprd,phy-delay-mmc-ddr52", MMC_TIMING_MMC_DDR52, },
  97         { "sprd,phy-delay-mmc-hs200", MMC_TIMING_MMC_HS200, },
  98         { "sprd,phy-delay-mmc-hs400", MMC_TIMING_MMC_HS400, },
  99         { "sprd,phy-delay-mmc-hs400es", MMC_TIMING_MMC_HS400 + 1, },
 100 };
 101
 102 #define TO_SPRD_HOST(host) sdhci_pltfm_priv(sdhci_priv(host))
 103
 104 static void sdhci_sprd_init_config(struct sdhci_host *host)
 105 {
 106         u16 val;
 107
 108         /* set dll backup mode */
 109         val = sdhci_readl(host, SDHCI_SPRD_REG_DEBOUNCE);
 110         val |= SDHCI_SPRD_BIT_DLL_BAK | SDHCI_SPRD_BIT_DLL_VAL;
 111         sdhci_writel(host, val, SDHCI_SPRD_REG_DEBOUNCE);
 112 }
 113
 114 static inline u32 sdhci_sprd_readl(struct sdhci_host *host, int reg)
 115 {
 116         if (unlikely(reg == SDHCI_MAX_CURRENT))
 117                 return SDHCI_SPRD_MAX_CUR;
 118
 119         return readl_relaxed(host->ioaddr + reg);
 120 }
 121
 122 static inline void sdhci_sprd_writel(struct sdhci_host *host, u32 val, int reg)
 123 {
 124         /* SDHCI_MAX_CURRENT is reserved on Spreadtrum's platform */
 125         if (unlikely(reg == SDHCI_MAX_CURRENT))
 126                 return;
 127
 128         if (unlikely(reg == SDHCI_SIGNAL_ENABLE || reg == SDHCI_INT_ENABLE))
 129                 val = val & SDHCI_SPRD_INT_SIGNAL_MASK;
 130
 131         writel_relaxed(val, host->ioaddr + reg);
 132 }
 133
 134 static inline void sdhci_sprd_writew(struct sdhci_host *host, u16 val, int reg)
 135 {
 136         /* SDHCI_BLOCK_COUNT is Read Only on Spreadtrum's platform */
 137         if (unlikely(reg == SDHCI_BLOCK_COUNT))
 138                 return;
 139
 140         writew_relaxed(val, host->ioaddr + reg);
 141 }
 142
 143 static inline void sdhci_sprd_writeb(struct sdhci_host *host, u8 val, int reg)
 144 {
 145         /*
 146          * Since BIT(3) of SDHCI_SOFTWARE_RESET is reserved according to the
 147          * standard specification, sdhci_reset() write this register directly
 148          * without checking other reserved bits, that will clear BIT(3) which
 149          * is defined as hardware reset on Spreadtrum's platform and clearing
 150          * it by mistake will lead the card not work. So here we need to work
 151          * around it.
 152          */
 153         if (unlikely(reg == SDHCI_SOFTWARE_RESET)) {
 154                 if (readb_relaxed(host->ioaddr + reg) & SDHCI_HW_RESET_CARD)
 155                         val |= SDHCI_HW_RESET_CARD;
 156         }
 157
 158         writeb_relaxed(val, host->ioaddr + reg);
 159 }
 160
 161 static inline void sdhci_sprd_sd_clk_off(struct sdhci_host *host)
 162 {
 163         u16 ctrl = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
 164
 165         ctrl &= ~SDHCI_CLOCK_CARD_EN;
 166         sdhci_writew(host, ctrl, SDHCI_CLOCK_CONTROL);
 167 }
 168
 169 static inline void sdhci_sprd_sd_clk_on(struct sdhci_host *host)
 170 {
 171         u16 ctrl;
 172
 173         ctrl = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
 174         ctrl |= SDHCI_CLOCK_CARD_EN;
 175         sdhci_writew(host, ctrl, SDHCI_CLOCK_CONTROL);
 176 }
 177
 178 static inline void
 179 sdhci_sprd_set_dll_invert(struct sdhci_host *host, u32 mask, bool en)
 180 {
 181         u32 dll_dly_offset;
 182
 183         dll_dly_offset = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_DLY_OFFSET);
 184         if (en)
 185                 dll_dly_offset |= mask;
 186         else
 187                 dll_dly_offset &= ~mask;
 188         sdhci_writel(host, dll_dly_offset, SDHCI_SPRD_REG_32_DLL_DLY_OFFSET);
 189 }
 190
 191 static inline u32 sdhci_sprd_calc_div(u32 base_clk, u32 clk)
 192 {
 193         u32 div;
 194
 195         /* select 2x clock source */
 196         if (base_clk <= clk * 2)
 197                 return 0;
 198
 199         div = (u32) (base_clk / (clk * 2));
 200
 201         if ((base_clk / div) > (clk * 2))
 202                 div++;
 203
 204         if (div > SDHCI_SPRD_CLK_MAX_DIV)
 205                 div = SDHCI_SPRD_CLK_MAX_DIV;
 206
 207         if (div % 2)
 208                 div = (div + 1) / 2;
 209         else
 210                 div = div / 2;
 211
 212         return div;
 213 }
 214
 215 static inline void _sdhci_sprd_set_clock(struct sdhci_host *host,
 216                                         unsigned int clk)
 217 {
 218         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 219         u32 div, val, mask;
 220
 221         sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
 222
 223         div = sdhci_sprd_calc_div(sprd_host->base_rate, clk);
 224         div = ((div & 0x300) >> 2) | ((div & 0xFF) << 8);
 225         sdhci_enable_clk(host, div);
 226
 227         /* enable auto gate sdhc_enable_auto_gate */
 228         val = sdhci_readl(host, SDHCI_SPRD_REG_32_BUSY_POSI);
 229         mask = SDHCI_SPRD_BIT_OUTR_CLK_AUTO_EN |
 230                SDHCI_SPRD_BIT_INNR_CLK_AUTO_EN;
 231         if (mask != (val & mask)) {
 232                 val |= mask;
 233                 sdhci_writel(host, val, SDHCI_SPRD_REG_32_BUSY_POSI);
 234         }
 235 }
 236
 237 static void sdhci_sprd_enable_phy_dll(struct sdhci_host *host)
 238 {
 239         u32 tmp;
 240
 241         tmp = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG);
 242         tmp &= ~(SDHCI_SPRD_DLL_EN | SDHCI_SPRD_DLL_ALL_CPST_EN);
 243         sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG);
 244         /* wait 1ms */
 245         usleep_range(1000, 1250);
 246
 247         tmp = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG);
 248         tmp |= SDHCI_SPRD_DLL_ALL_CPST_EN | SDHCI_SPRD_DLL_SEARCH_MODE |
 249                 SDHCI_SPRD_DLL_INIT_COUNT | SDHCI_SPRD_DLL_PHASE_INTERNAL;
 250         sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG);
 251         /* wait 1ms */
 252         usleep_range(1000, 1250);
 253
 254         tmp = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG);
 255         tmp |= SDHCI_SPRD_DLL_EN;
 256         sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG);
 257         /* wait 1ms */
 258         usleep_range(1000, 1250);
 259 }
 260
 261 static void sdhci_sprd_set_clock(struct sdhci_host *host, unsigned int clock)
 262 {
 263         bool en = false, clk_changed = false;
 264
 265         if (clock == 0) {
 266                 sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
 267         } else if (clock != host->clock) {
 268                 sdhci_sprd_sd_clk_off(host);
 269                 _sdhci_sprd_set_clock(host, clock);
 270
 271                 if (clock <= 400000)
 272                         en = true;
 273                 sdhci_sprd_set_dll_invert(host, SDHCI_SPRD_BIT_CMD_DLY_INV |
 274                                           SDHCI_SPRD_BIT_POSRD_DLY_INV, en);
 275                 clk_changed = true;
 276         } else {
 277                 _sdhci_sprd_set_clock(host, clock);
 278         }
 279
 280         /*
 281          * According to the Spreadtrum SD host specification, when we changed
 282          * the clock to be more than 52M, we should enable the PHY DLL which
 283          * is used to track the clock frequency to make the clock work more
 284          * stable. Otherwise deviation may occur of the higher clock.
 285          */
 286         if (clk_changed && clock > SDHCI_SPRD_PHY_DLL_CLK)
 287                 sdhci_sprd_enable_phy_dll(host);
 288 }
 289
 290 static unsigned int sdhci_sprd_get_max_clock(struct sdhci_host *host)
 291 {
 292         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 293
 294         return clk_round_rate(sprd_host->clk_sdio, ULONG_MAX);
 295 }
 296
 297 static unsigned int sdhci_sprd_get_min_clock(struct sdhci_host *host)
 298 {
 299         return 400000;
 300 }
 301
 302 static void sdhci_sprd_set_uhs_signaling(struct sdhci_host *host,
 303                                          unsigned int timing)
 304 {
 305         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 306         struct mmc_host *mmc = host->mmc;
 307         u32 *p = sprd_host->phy_delay;
 308         u16 ctrl_2;
 309
 310         if (timing == host->timing)
 311                 return;
 312
 313         ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
 314         /* Select Bus Speed Mode for host */
 315         ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
 316         switch (timing) {
 317         case MMC_TIMING_UHS_SDR12:
 318                 ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
 319                 break;
 320         case MMC_TIMING_MMC_HS:
 321         case MMC_TIMING_SD_HS:
 322         case MMC_TIMING_UHS_SDR25:
 323                 ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
 324                 break;
 325         case MMC_TIMING_UHS_SDR50:
 326                 ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
 327                 break;
 328         case MMC_TIMING_UHS_SDR104:
 329                 ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
 330                 break;
 331         case MMC_TIMING_UHS_DDR50:
 332         case MMC_TIMING_MMC_DDR52:
 333                 ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
 334                 break;
 335         case MMC_TIMING_MMC_HS200:
 336                 ctrl_2 |= SDHCI_SPRD_CTRL_HS200;
 337                 break;
 338         case MMC_TIMING_MMC_HS400:
 339                 ctrl_2 |= SDHCI_SPRD_CTRL_HS400;
 340                 break;
 341         default:
 342                 break;
 343         }
 344
 345         sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
 346
 347         if (!mmc->ios.enhanced_strobe)
 348                 sdhci_writel(host, p[timing], SDHCI_SPRD_REG_32_DLL_DLY);
 349 }
 350
 351 static void sdhci_sprd_hw_reset(struct sdhci_host *host)
 352 {
 353         int val;
 354
 355         /*
 356          * Note: don't use sdhci_writeb() API here since it is redirected to
 357          * sdhci_sprd_writeb() in which we have a workaround for
 358          * SDHCI_SOFTWARE_RESET which would make bit SDHCI_HW_RESET_CARD can
 359          * not be cleared.
 360          */
 361         val = readb_relaxed(host->ioaddr + SDHCI_SOFTWARE_RESET);
 362         val &= ~SDHCI_HW_RESET_CARD;
 363         writeb_relaxed(val, host->ioaddr + SDHCI_SOFTWARE_RESET);
 364         /* wait for 10 us */
 365         usleep_range(10, 20);
 366
 367         val |= SDHCI_HW_RESET_CARD;
 368         writeb_relaxed(val, host->ioaddr + SDHCI_SOFTWARE_RESET);
 369         usleep_range(300, 500);
 370 }
 371
 372 static unsigned int sdhci_sprd_get_max_timeout_count(struct sdhci_host *host)
 373 {
 374         /* The Spredtrum controller actual maximum timeout count is 1 << 31 */
 375         return 1 << 31;
 376 }
 377
 378 static unsigned int sdhci_sprd_get_ro(struct sdhci_host *host)
 379 {
 380         return 0;
 381 }
 382
 383 static void sdhci_sprd_request_done(struct sdhci_host *host,
 384                                     struct mmc_request *mrq)
 385 {
 386         /* Validate if the request was from software queue firstly. */
 387         if (mmc_hsq_finalize_request(host->mmc, mrq))
 388                 return;
 389
 390         mmc_request_done(host->mmc, mrq);
 391 }
 392
 393 static struct sdhci_ops sdhci_sprd_ops = {
 394         .read_l = sdhci_sprd_readl,
 395         .write_l = sdhci_sprd_writel,
 396         .write_w = sdhci_sprd_writew,
 397         .write_b = sdhci_sprd_writeb,
 398         .set_clock = sdhci_sprd_set_clock,
 399         .get_max_clock = sdhci_sprd_get_max_clock,
 400         .get_min_clock = sdhci_sprd_get_min_clock,
 401         .set_bus_width = sdhci_set_bus_width,
 402         .reset = sdhci_reset,
 403         .set_uhs_signaling = sdhci_sprd_set_uhs_signaling,
 404         .hw_reset = sdhci_sprd_hw_reset,
 405         .get_max_timeout_count = sdhci_sprd_get_max_timeout_count,
 406         .get_ro = sdhci_sprd_get_ro,
 407         .request_done = sdhci_sprd_request_done,
 408 };
 409
 410 static void sdhci_sprd_check_auto_cmd23(struct mmc_host *mmc,
 411                                         struct mmc_request *mrq)
 412 {
 413         struct sdhci_host *host = mmc_priv(mmc);
 414         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 415
 416         host->flags |= sprd_host->flags & SDHCI_AUTO_CMD23;
 417
 418         /*
 419          * From version 4.10 onward, ARGUMENT2 register is also as 32-bit
 420          * block count register which doesn't support stuff bits of
 421          * CMD23 argument on Spreadtrum's sd host controller.
 422          */
 423         if (host->version >= SDHCI_SPEC_410 &&
 424             mrq->sbc && (mrq->sbc->arg & SDHCI_SPRD_ARG2_STUFF) &&
 425             (host->flags & SDHCI_AUTO_CMD23))
 426                 host->flags &= ~SDHCI_AUTO_CMD23;
 427 }
 428
 429 static void sdhci_sprd_request(struct mmc_host *mmc, struct mmc_request *mrq)
 430 {
 431         sdhci_sprd_check_auto_cmd23(mmc, mrq);
 432
 433         sdhci_request(mmc, mrq);
 434 }
 435
 436 static int sdhci_sprd_request_atomic(struct mmc_host *mmc,
 437                                      struct mmc_request *mrq)
 438 {
 439         sdhci_sprd_check_auto_cmd23(mmc, mrq);
 440
 441         return sdhci_request_atomic(mmc, mrq);
 442 }
 443
 444 static int sdhci_sprd_voltage_switch(struct mmc_host *mmc, struct mmc_ios *ios)
 445 {
 446         struct sdhci_host *host = mmc_priv(mmc);
 447         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 448         int ret;
 449
 450         if (!IS_ERR(mmc->supply.vqmmc)) {
 451                 ret = mmc_regulator_set_vqmmc(mmc, ios);
 452                 if (ret < 0) {
 453                         pr_err("%s: Switching signalling voltage failed\n",
 454                                mmc_hostname(mmc));
 455                         return ret;
 456                 }
 457         }
 458
 459         if (IS_ERR(sprd_host->pinctrl))
 460                 return 0;
 461
 462         switch (ios->signal_voltage) {
 463         case MMC_SIGNAL_VOLTAGE_180:
 464                 ret = pinctrl_select_state(sprd_host->pinctrl,
 465                                            sprd_host->pins_uhs);
 466                 if (ret) {
 467                         pr_err("%s: failed to select uhs pin state\n",
 468                                mmc_hostname(mmc));
 469                         return ret;
 470                 }
 471                 break;
 472
 473         default:
 474                 fallthrough;
 475         case MMC_SIGNAL_VOLTAGE_330:
 476                 ret = pinctrl_select_state(sprd_host->pinctrl,
 477                                            sprd_host->pins_default);
 478                 if (ret) {
 479                         pr_err("%s: failed to select default pin state\n",
 480                                mmc_hostname(mmc));
 481                         return ret;
 482                 }
 483                 break;
 484         }
 485
 486         /* Wait for 300 ~ 500 us for pin state stable */
 487         usleep_range(300, 500);
 488         sdhci_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
 489
 490         return 0;
 491 }
 492
 493 static void sdhci_sprd_hs400_enhanced_strobe(struct mmc_host *mmc,
 494                                              struct mmc_ios *ios)
 495 {
 496         struct sdhci_host *host = mmc_priv(mmc);
 497         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 498         u32 *p = sprd_host->phy_delay;
 499         u16 ctrl_2;
 500
 501         if (!ios->enhanced_strobe)
 502                 return;
 503
 504         sdhci_sprd_sd_clk_off(host);
 505
 506         /* Set HS400 enhanced strobe mode */
 507         ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
 508         ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
 509         ctrl_2 |= SDHCI_SPRD_CTRL_HS400ES;
 510         sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
 511
 512         sdhci_sprd_sd_clk_on(host);
 513
 514         /* Set the PHY DLL delay value for HS400 enhanced strobe mode */
 515         sdhci_writel(host, p[MMC_TIMING_MMC_HS400 + 1],
 516                      SDHCI_SPRD_REG_32_DLL_DLY);
 517 }
 518
 519 static void sdhci_sprd_phy_param_parse(struct sdhci_sprd_host *sprd_host,
 520                                        struct device_node *np)
 521 {
 522         u32 *p = sprd_host->phy_delay;
 523         int ret, i, index;
 524         u32 val[4];
 525
 526         for (i = 0; i < ARRAY_SIZE(sdhci_sprd_phy_cfgs); i++) {
 527                 ret = of_property_read_u32_array(np,
 528                                 sdhci_sprd_phy_cfgs[i].property, val, 4);
 529                 if (ret)
 530                         continue;
 531
 532                 index = sdhci_sprd_phy_cfgs[i].timing;
 533                 p[index] = val[0] | (val[1] << 8) | (val[2] << 16) | (val[3] << 24);
 534         }
 535 }
 536
 537 static const struct sdhci_pltfm_data sdhci_sprd_pdata = {
 538         .quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION |
 539                   SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK |
 540                   SDHCI_QUIRK_MISSING_CAPS,
 541         .quirks2 = SDHCI_QUIRK2_BROKEN_HS200 |
 542                    SDHCI_QUIRK2_USE_32BIT_BLK_CNT |
 543                    SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
 544         .ops = &sdhci_sprd_ops,
 545 };
 546
 547 static int sdhci_sprd_probe(struct platform_device *pdev)
 548 {
 549         struct sdhci_host *host;
 550         struct sdhci_sprd_host *sprd_host;
 551         struct mmc_hsq *hsq;
 552         struct clk *clk;
 553         int ret = 0;
 554
 555         host = sdhci_pltfm_init(pdev, &sdhci_sprd_pdata, sizeof(*sprd_host));
 556         if (IS_ERR(host))
 557                 return PTR_ERR(host);
 558
 559         host->dma_mask = DMA_BIT_MASK(64);
 560         pdev->dev.dma_mask = &host->dma_mask;
 561         host->mmc_host_ops.request = sdhci_sprd_request;
 562         host->mmc_host_ops.hs400_enhanced_strobe =
 563                 sdhci_sprd_hs400_enhanced_strobe;
 564         /*
 565          * We can not use the standard ops to change and detect the voltage
 566          * signal for Spreadtrum SD host controller, since our voltage regulator
 567          * for I/O is fixed in hardware, that means we do not need control
 568          * the standard SD host controller to change the I/O voltage.
 569          */
 570         host->mmc_host_ops.start_signal_voltage_switch =
 571                 sdhci_sprd_voltage_switch;
 572
 573         host->mmc->caps = MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED |
 574                 MMC_CAP_WAIT_WHILE_BUSY;
 575
 576         ret = mmc_of_parse(host->mmc);
 577         if (ret)
 578                 goto pltfm_free;
 579
 580         if (!mmc_card_is_removable(host->mmc))
 581                 host->mmc_host_ops.request_atomic = sdhci_sprd_request_atomic;
 582         else
 583                 host->always_defer_done = true;
 584
 585         sprd_host = TO_SPRD_HOST(host);
 586         sdhci_sprd_phy_param_parse(sprd_host, pdev->dev.of_node);
 587
 588         sprd_host->pinctrl = devm_pinctrl_get(&pdev->dev);
 589         if (!IS_ERR(sprd_host->pinctrl)) {
 590                 sprd_host->pins_uhs =
 591                         pinctrl_lookup_state(sprd_host->pinctrl, "state_uhs");
 592                 if (IS_ERR(sprd_host->pins_uhs)) {
 593                         ret = PTR_ERR(sprd_host->pins_uhs);
 594                         goto pltfm_free;
 595                 }
 596
 597                 sprd_host->pins_default =
 598                         pinctrl_lookup_state(sprd_host->pinctrl, "default");
 599                 if (IS_ERR(sprd_host->pins_default)) {
 600                         ret = PTR_ERR(sprd_host->pins_default);
 601                         goto pltfm_free;
 602                 }
 603         }
 604
 605         clk = devm_clk_get(&pdev->dev, "sdio");
 606         if (IS_ERR(clk)) {
 607                 ret = PTR_ERR(clk);
 608                 goto pltfm_free;
 609         }
 610         sprd_host->clk_sdio = clk;
 611         sprd_host->base_rate = clk_get_rate(sprd_host->clk_sdio);
 612         if (!sprd_host->base_rate)
 613                 sprd_host->base_rate = SDHCI_SPRD_CLK_DEF_RATE;
 614
 615         clk = devm_clk_get(&pdev->dev, "enable");
 616         if (IS_ERR(clk)) {
 617                 ret = PTR_ERR(clk);
 618                 goto pltfm_free;
 619         }
 620         sprd_host->clk_enable = clk;
 621
 622         clk = devm_clk_get(&pdev->dev, "2x_enable");
 623         if (!IS_ERR(clk))
 624                 sprd_host->clk_2x_enable = clk;
 625
 626         ret = clk_prepare_enable(sprd_host->clk_sdio);
 627         if (ret)
 628                 goto pltfm_free;
 629
 630         ret = clk_prepare_enable(sprd_host->clk_enable);
 631         if (ret)
 632                 goto clk_disable;
 633
 634         ret = clk_prepare_enable(sprd_host->clk_2x_enable);
 635         if (ret)
 636                 goto clk_disable2;
 637
 638         sdhci_sprd_init_config(host);
 639         host->version = sdhci_readw(host, SDHCI_HOST_VERSION);
 640         sprd_host->version = ((host->version & SDHCI_VENDOR_VER_MASK) >>
 641                                SDHCI_VENDOR_VER_SHIFT);
 642
 643         pm_runtime_get_noresume(&pdev->dev);
 644         pm_runtime_set_active(&pdev->dev);
 645         pm_runtime_enable(&pdev->dev);
 646         pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
 647         pm_runtime_use_autosuspend(&pdev->dev);
 648         pm_suspend_ignore_children(&pdev->dev, 1);
 649
 650         sdhci_enable_v4_mode(host);
 651
 652         /*
 653          * Supply the existing CAPS, but clear the UHS-I modes. This
 654          * will allow these modes to be specified only by device
 655          * tree properties through mmc_of_parse().
 656          */
 657         host->caps = sdhci_readl(host, SDHCI_CAPABILITIES);
 658         host->caps1 = sdhci_readl(host, SDHCI_CAPABILITIES_1);
 659         host->caps1 &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_SDR104 |
 660                          SDHCI_SUPPORT_DDR50);
 661
 662         ret = sdhci_setup_host(host);
 663         if (ret)
 664                 goto pm_runtime_disable;
 665
 666         sprd_host->flags = host->flags;
 667
 668         hsq = devm_kzalloc(&pdev->dev, sizeof(*hsq), GFP_KERNEL);
 669         if (!hsq) {
 670                 ret = -ENOMEM;
 671                 goto err_cleanup_host;
 672         }
 673
 674         ret = mmc_hsq_init(hsq, host->mmc);
 675         if (ret)
 676                 goto err_cleanup_host;
 677
 678         ret = __sdhci_add_host(host);
 679         if (ret)
 680                 goto err_cleanup_host;
 681
 682         pm_runtime_mark_last_busy(&pdev->dev);
 683         pm_runtime_put_autosuspend(&pdev->dev);
 684
 685         return 0;
 686
 687 err_cleanup_host:
 688         sdhci_cleanup_host(host);
 689
 690 pm_runtime_disable:
 691         pm_runtime_put_noidle(&pdev->dev);
 692         pm_runtime_disable(&pdev->dev);
 693         pm_runtime_set_suspended(&pdev->dev);
 694
 695         clk_disable_unprepare(sprd_host->clk_2x_enable);
 696
 697 clk_disable2:
 698         clk_disable_unprepare(sprd_host->clk_enable);
 699
 700 clk_disable:
 701         clk_disable_unprepare(sprd_host->clk_sdio);
 702
 703 pltfm_free:
 704         sdhci_pltfm_free(pdev);
 705         return ret;
 706 }
 707
 708 static int sdhci_sprd_remove(struct platform_device *pdev)
 709 {
 710         struct sdhci_host *host = platform_get_drvdata(pdev);
 711         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 712
 713         sdhci_remove_host(host, 0);
 714
 715         clk_disable_unprepare(sprd_host->clk_sdio);
 716         clk_disable_unprepare(sprd_host->clk_enable);
 717         clk_disable_unprepare(sprd_host->clk_2x_enable);
 718
 719         sdhci_pltfm_free(pdev);
 720
 721         return 0;
 722 }
 723
 724 static const struct of_device_id sdhci_sprd_of_match[] = {
 725         { .compatible = "sprd,sdhci-r11", },
 726         { }
 727 };
 728 MODULE_DEVICE_TABLE(of, sdhci_sprd_of_match);
 729
 730 #ifdef CONFIG_PM
 731 static int sdhci_sprd_runtime_suspend(struct device *dev)
 732 {
 733         struct sdhci_host *host = dev_get_drvdata(dev);
 734         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 735
 736         mmc_hsq_suspend(host->mmc);
 737         sdhci_runtime_suspend_host(host);
 738
 739         clk_disable_unprepare(sprd_host->clk_sdio);
 740         clk_disable_unprepare(sprd_host->clk_enable);
 741         clk_disable_unprepare(sprd_host->clk_2x_enable);
 742
 743         return 0;
 744 }
 745
 746 static int sdhci_sprd_runtime_resume(struct device *dev)
 747 {
 748         struct sdhci_host *host = dev_get_drvdata(dev);
 749         struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 750         int ret;
 751
 752         ret = clk_prepare_enable(sprd_host->clk_2x_enable);
 753         if (ret)
 754                 return ret;
 755
 756         ret = clk_prepare_enable(sprd_host->clk_enable);
 757         if (ret)
 758                 goto clk_2x_disable;
 759
 760         ret = clk_prepare_enable(sprd_host->clk_sdio);
 761         if (ret)
 762                 goto clk_disable;
 763
 764         sdhci_runtime_resume_host(host, 1);
 765         mmc_hsq_resume(host->mmc);
 766
 767         return 0;
 768
 769 clk_disable:
 770         clk_disable_unprepare(sprd_host->clk_enable);
 771
 772 clk_2x_disable:
 773         clk_disable_unprepare(sprd_host->clk_2x_enable);
 774
 775         return ret;
 776 }
 777 #endif
 778
 779 static const struct dev_pm_ops sdhci_sprd_pm_ops = {
 780         SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
 781                                 pm_runtime_force_resume)
 782         SET_RUNTIME_PM_OPS(sdhci_sprd_runtime_suspend,
 783                            sdhci_sprd_runtime_resume, NULL)
 784 };
 785
 786 static struct platform_driver sdhci_sprd_driver = {
 787         .probe = sdhci_sprd_probe,
 788         .remove = sdhci_sprd_remove,
 789         .driver = {
 790                 .name = "sdhci_sprd_r11",
 791                 .probe_type = PROBE_PREFER_ASYNCHRONOUS,
 792                 .of_match_table = sdhci_sprd_of_match,
 793                 .pm = &sdhci_sprd_pm_ops,
 794         },
 795 };
 796 module_platform_driver(sdhci_sprd_driver);
 797
 798 MODULE_DESCRIPTION("Spreadtrum sdio host controller r11 driver");
 799 MODULE_LICENSE("GPL v2");
 800 MODULE_ALIAS("platform:sdhci-sprd-r11");