1 # SPDX-License-Identifier: GPL-2.0-only
3 # Touchscreen driver configuration
5 menuconfig INPUT_TOUCHSCREEN
8 Say Y here, and a list of supported touchscreens will be displayed.
9 This option doesn't affect the kernel.
15 config TOUCHSCREEN_88PM860X
16 tristate "Marvell 88PM860x touchscreen"
17 depends on MFD_88PM860X
19 Say Y here if you have a 88PM860x PMIC and want to enable
20 support for the built-in touchscreen.
24 To compile this driver as a module, choose M here: the
25 module will be called 88pm860x-ts.
27 config TOUCHSCREEN_ADS7846
28 tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens"
30 depends on HWMON = n || HWMON
32 Say Y here if you have a touchscreen interface using the
33 ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller,
34 and your board-specific setup code includes that in its
37 If HWMON is selected, and the driver is told the reference voltage
38 on your board, you will also get hwmon interfaces for the voltage
39 (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip.
41 If unsure, say N (but it's safe to say "Y").
43 To compile this driver as a module, choose M here: the
44 module will be called ads7846.
46 config TOUCHSCREEN_AD7877
47 tristate "AD7877 based touchscreens"
50 Say Y here if you have a touchscreen interface using the
51 AD7877 controller, and your board-specific initialization
52 code includes that in its table of SPI devices.
54 If unsure, say N (but it's safe to say "Y").
56 To compile this driver as a module, choose M here: the
57 module will be called ad7877.
59 config TOUCHSCREEN_AD7879
60 tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface"
62 Say Y here if you want to support a touchscreen interface using
63 the AD7879-1/AD7889-1 controller.
65 You should select a bus connection too.
67 To compile this driver as a module, choose M here: the
68 module will be called ad7879.
70 config TOUCHSCREEN_AD7879_I2C
71 tristate "support I2C bus connection"
72 depends on TOUCHSCREEN_AD7879 && I2C
75 Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus.
77 To compile this driver as a module, choose M here: the
78 module will be called ad7879-i2c.
80 config TOUCHSCREEN_AD7879_SPI
81 tristate "support SPI bus connection"
82 depends on TOUCHSCREEN_AD7879 && SPI_MASTER
85 Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus.
87 If unsure, say N (but it's safe to say "Y").
89 To compile this driver as a module, choose M here: the
90 module will be called ad7879-spi.
92 config TOUCHSCREEN_ADC
93 tristate "Generic ADC based resistive touchscreen"
98 Say Y here if you want to use the generic ADC
99 resistive touchscreen driver.
101 If unsure, say N (but it's safe to say "Y").
103 To compile this driver as a module, choose M here: the
104 module will be called resistive-adc-touch.ko.
106 config TOUCHSCREEN_AR1021_I2C
107 tristate "Microchip AR1020/1021 i2c touchscreen"
110 Say Y here if you have the Microchip AR1020 or AR1021 touchscreen
111 controller chip in your system.
115 To compile this driver as a module, choose M here: the
116 module will be called ar1021_i2c.
118 config TOUCHSCREEN_ATMEL_MXT
119 tristate "Atmel mXT I2C Touchscreen"
123 Say Y here if you have Atmel mXT series I2C touchscreen,
124 such as AT42QT602240/ATMXT224, connected to your system.
128 To compile this driver as a module, choose M here: the
129 module will be called atmel_mxt_ts.
131 config TOUCHSCREEN_ATMEL_MXT_T37
132 bool "Support T37 Diagnostic Data"
133 depends on TOUCHSCREEN_ATMEL_MXT
134 depends on VIDEO_V4L2=y || (TOUCHSCREEN_ATMEL_MXT=m && VIDEO_V4L2=m)
135 select VIDEOBUF2_VMALLOC
137 Say Y here if you want support to output data from the T37
138 Diagnostic Data object using a V4L device.
140 config TOUCHSCREEN_AUO_PIXCIR
141 tristate "AUO in-cell touchscreen using Pixcir ICs"
143 depends on GPIOLIB || COMPILE_TEST
145 Say Y here if you have a AUO display with in-cell touchscreen
150 To compile this driver as a module, choose M here: the
151 module will be called auo-pixcir-ts.
153 config TOUCHSCREEN_BU21013
154 tristate "BU21013 based touch panel controllers"
157 Say Y here if you have a bu21013 touchscreen connected to
162 To compile this driver as a module, choose M here: the
163 module will be called bu21013_ts.
165 config TOUCHSCREEN_BU21029
166 tristate "Rohm BU21029 based touch panel controllers"
169 Say Y here if you have a Rohm BU21029 touchscreen controller
170 connected to your system.
174 To compile this driver as a module, choose M here: the
175 module will be called bu21029_ts.
177 config TOUCHSCREEN_CHIPONE_ICN8318
178 tristate "chipone icn8318 touchscreen controller"
179 depends on GPIOLIB || COMPILE_TEST
183 Say Y here if you have a ChipOne icn8318 based I2C touchscreen.
187 To compile this driver as a module, choose M here: the
188 module will be called chipone_icn8318.
190 config TOUCHSCREEN_CHIPONE_ICN8505
191 tristate "chipone icn8505 touchscreen controller"
192 depends on I2C && ACPI
194 Say Y here if you have a ChipOne icn8505 based I2C touchscreen.
198 To compile this driver as a module, choose M here: the
199 module will be called chipone_icn8505.
201 config TOUCHSCREEN_CY8CTMA140
202 tristate "cy8ctma140 touchscreen"
205 Say Y here if you have a Cypress CY8CTMA140 capacitive
206 touchscreen also just known as "TMA140"
210 To compile this driver as a module, choose M here: the
211 module will be called cy8ctma140.
213 config TOUCHSCREEN_CY8CTMG110
214 tristate "cy8ctmg110 touchscreen"
216 depends on GPIOLIB || COMPILE_TEST
218 Say Y here if you have a cy8ctmg110 capacitive touchscreen on
223 To compile this driver as a module, choose M here: the
224 module will be called cy8ctmg110_ts.
226 config TOUCHSCREEN_CYTTSP_CORE
227 tristate "Cypress TTSP touchscreen"
229 Say Y here if you have a touchscreen using controller from
230 the Cypress TrueTouch(tm) Standard Product family connected
231 to your system. You will also need to select appropriate
232 bus connection below.
236 To compile this driver as a module, choose M here: the
237 module will be called cyttsp_core.
239 config TOUCHSCREEN_CYTTSP_I2C
240 tristate "support I2C bus connection"
241 depends on TOUCHSCREEN_CYTTSP_CORE && I2C
243 Say Y here if the touchscreen is connected via I2C bus.
245 To compile this driver as a module, choose M here: the
246 module will be called cyttsp_i2c.
248 config TOUCHSCREEN_CYTTSP_SPI
249 tristate "support SPI bus connection"
250 depends on TOUCHSCREEN_CYTTSP_CORE && SPI_MASTER
252 Say Y here if the touchscreen is connected via SPI bus.
254 To compile this driver as a module, choose M here: the
255 module will be called cyttsp_spi.
257 config TOUCHSCREEN_CYTTSP4_CORE
258 tristate "Cypress TrueTouch Gen4 Touchscreen Driver"
260 Core driver for Cypress TrueTouch(tm) Standard Product
261 Generation4 touchscreen controllers.
263 Say Y here if you have a Cypress Gen4 touchscreen.
267 To compile this driver as a module, choose M here.
269 config TOUCHSCREEN_CYTTSP4_I2C
270 tristate "support I2C bus connection"
271 depends on TOUCHSCREEN_CYTTSP4_CORE && I2C
273 Say Y here if the touchscreen is connected via I2C bus.
275 To compile this driver as a module, choose M here: the
276 module will be called cyttsp4_i2c.
278 config TOUCHSCREEN_CYTTSP4_SPI
279 tristate "support SPI bus connection"
280 depends on TOUCHSCREEN_CYTTSP4_CORE && SPI_MASTER
282 Say Y here if the touchscreen is connected via SPI bus.
284 To compile this driver as a module, choose M here: the
285 module will be called cyttsp4_spi.
287 config TOUCHSCREEN_DA9034
288 tristate "Touchscreen support for Dialog Semiconductor DA9034"
289 depends on PMIC_DA903X
292 Say Y here to enable the support for the touchscreen found
293 on Dialog Semiconductor DA9034 PMIC.
297 To compile this driver as a module, choose M here: the
298 module will be called da9034-ts.
300 config TOUCHSCREEN_DA9052
301 tristate "Dialog DA9052/DA9053 TSI"
302 depends on PMIC_DA9052
304 Say Y here to support the touchscreen found on Dialog Semiconductor
305 DA9052-BC and DA9053-AA/Bx PMICs.
309 To compile this driver as a module, choose M here: the
310 module will be called da9052_tsi.
312 config TOUCHSCREEN_DYNAPRO
313 tristate "Dynapro serial touchscreen"
316 Say Y here if you have a Dynapro serial touchscreen connected to
321 To compile this driver as a module, choose M here: the
322 module will be called dynapro.
324 config TOUCHSCREEN_HAMPSHIRE
325 tristate "Hampshire serial touchscreen"
328 Say Y here if you have a Hampshire serial touchscreen connected to
333 To compile this driver as a module, choose M here: the
334 module will be called hampshire.
336 config TOUCHSCREEN_EETI
337 tristate "EETI touchscreen panel support"
340 Say Y here to enable support for I2C connected EETI touch panels.
342 To compile this driver as a module, choose M here: the
343 module will be called eeti_ts.
345 config TOUCHSCREEN_EGALAX
346 tristate "EETI eGalax multi-touch panel support"
349 Say Y here to enable support for I2C connected EETI
350 eGalax multi-touch panels.
352 To compile this driver as a module, choose M here: the
353 module will be called egalax_ts.
355 config TOUCHSCREEN_EGALAX_SERIAL
356 tristate "EETI eGalax serial touchscreen"
359 Say Y here to enable support for serial connected EETI
362 To compile this driver as a module, choose M here: the
363 module will be called egalax_ts_serial.
365 config TOUCHSCREEN_EXC3000
366 tristate "EETI EXC3000 multi-touch panel support"
369 Say Y here to enable support for I2C connected EETI
370 EXC3000 multi-touch panels.
372 To compile this driver as a module, choose M here: the
373 module will be called exc3000.
375 config TOUCHSCREEN_FUJITSU
376 tristate "Fujitsu serial touchscreen"
379 Say Y here if you have the Fujitsu touchscreen (such as one
380 installed in Lifebook P series laptop) connected to your
385 To compile this driver as a module, choose M here: the
386 module will be called fujitsu-ts.
388 config TOUCHSCREEN_GOODIX
389 tristate "Goodix I2C touchscreen"
391 depends on GPIOLIB || COMPILE_TEST
393 Say Y here if you have the Goodix touchscreen (such as one
394 installed in Onda v975w tablets) connected to your
395 system. It also supports 5-finger chip models, which can be
396 found on ARM tablets, like Wexler TAB7200 and MSI Primo73.
400 To compile this driver as a module, choose M here: the
401 module will be called goodix.
403 config TOUCHSCREEN_HIDEEP
404 tristate "HiDeep Touch IC"
407 Say Y here if you have a touchscreen using HiDeep.
411 To compile this driver as a module, choose M here : the
412 module will be called hideep_ts.
414 config TOUCHSCREEN_ILI210X
415 tristate "Ilitek ILI210X based touchscreen"
418 Say Y here if you have a ILI210X based touchscreen
419 controller. This driver supports models ILI2102,
420 ILI2102s, ILI2103, ILI2103s and ILI2105.
421 Such kind of chipsets can be found in Amazon Kindle Fire
426 To compile this driver as a module, choose M here: the
427 module will be called ili210x.
429 config TOUCHSCREEN_IPROC
430 tristate "IPROC touch panel driver support"
431 depends on ARCH_BCM_IPROC || COMPILE_TEST
433 Say Y here if you want to add support for the IPROC touch
434 controller to your system.
438 To compile this driver as a module, choose M here: the
439 module will be called bcm_iproc_tsc.
441 config TOUCHSCREEN_S3C2410
442 tristate "Samsung S3C2410/generic touchscreen input driver"
443 depends on ARCH_S3C24XX || SAMSUNG_DEV_TS
446 Say Y here if you have the s3c2410 touchscreen.
450 To compile this driver as a module, choose M here: the
451 module will be called s3c2410_ts.
453 config TOUCHSCREEN_S6SY761
454 tristate "Samsung S6SY761 Touchscreen driver"
457 Say Y if you have the Samsung S6SY761 driver
461 To compile this driver as module, choose M here: the
462 module will be called s6sy761.
464 config TOUCHSCREEN_GUNZE
465 tristate "Gunze AHL-51S touchscreen"
468 Say Y here if you have the Gunze AHL-51 touchscreen connected to
473 To compile this driver as a module, choose M here: the
474 module will be called gunze.
476 config TOUCHSCREEN_EKTF2127
477 tristate "Elan eKTF2127 I2C touchscreen"
480 Say Y here if you have an Elan eKTF2127 touchscreen
481 connected to your system.
485 To compile this driver as a module, choose M here: the
486 module will be called ektf2127.
488 config TOUCHSCREEN_ELAN
489 tristate "Elan eKTH I2C touchscreen"
492 Say Y here if you have an Elan eKTH I2C touchscreen
493 connected to your system.
497 To compile this driver as a module, choose M here: the
498 module will be called elants_i2c.
500 config TOUCHSCREEN_ELO
501 tristate "Elo serial touchscreens"
504 Say Y here if you have an Elo serial touchscreen connected to
509 To compile this driver as a module, choose M here: the
510 module will be called elo.
512 config TOUCHSCREEN_WACOM_W8001
513 tristate "Wacom W8001 penabled serial touchscreen"
516 Say Y here if you have an Wacom W8001 penabled serial touchscreen
517 connected to your system.
521 To compile this driver as a module, choose M here: the
522 module will be called wacom_w8001.
524 config TOUCHSCREEN_WACOM_I2C
525 tristate "Wacom Tablet support (I2C)"
528 Say Y here if you want to use the I2C version of the Wacom
533 To compile this driver as a module, choose M here: the module
534 will be called wacom_i2c.
536 config TOUCHSCREEN_LPC32XX
537 tristate "LPC32XX touchscreen controller"
538 depends on ARCH_LPC32XX
540 Say Y here if you have a LPC32XX device and want
541 to support the built-in touchscreen.
543 To compile this driver as a module, choose M here: the
544 module will be called lpc32xx_ts.
546 config TOUCHSCREEN_MAX11801
547 tristate "MAX11801 based touchscreens"
550 Say Y here if you have a MAX11801 based touchscreen
555 To compile this driver as a module, choose M here: the
556 module will be called max11801_ts.
558 config TOUCHSCREEN_MCS5000
559 tristate "MELFAS MCS-5000 touchscreen"
562 Say Y here if you have the MELFAS MCS-5000 touchscreen controller
567 To compile this driver as a module, choose M here: the
568 module will be called mcs5000_ts.
570 config TOUCHSCREEN_MMS114
571 tristate "MELFAS MMS114 touchscreen"
574 Say Y here if you have the MELFAS MMS114 touchscreen controller
579 To compile this driver as a module, choose M here: the
580 module will be called mms114.
582 config TOUCHSCREEN_MELFAS_MIP4
583 tristate "MELFAS MIP4 Touchscreen"
586 Say Y here if you have a MELFAS MIP4 Touchscreen device.
590 To compile this driver as a module, choose M here:
591 the module will be called melfas_mip4.
593 config TOUCHSCREEN_MTOUCH
594 tristate "MicroTouch serial touchscreens"
597 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
602 To compile this driver as a module, choose M here: the
603 module will be called mtouch.
605 config TOUCHSCREEN_IMX6UL_TSC
606 tristate "Freescale i.MX6UL touchscreen controller"
607 depends on ((OF && GPIOLIB) || COMPILE_TEST) && HAS_IOMEM
609 Say Y here if you have a Freescale i.MX6UL, and want to
610 use the internal touchscreen controller.
614 To compile this driver as a module, choose M here: the
615 module will be called imx6ul_tsc.
617 config TOUCHSCREEN_INEXIO
618 tristate "iNexio serial touchscreens"
621 Say Y here if you have an iNexio serial touchscreen connected to
626 To compile this driver as a module, choose M here: the
627 module will be called inexio.
629 config TOUCHSCREEN_MK712
630 tristate "ICS MicroClock MK712 touchscreen"
632 Say Y here if you have the ICS MicroClock MK712 touchscreen
633 controller chip in your system.
637 To compile this driver as a module, choose M here: the
638 module will be called mk712.
640 config TOUCHSCREEN_HP600
641 tristate "HP Jornada 6xx touchscreen"
642 depends on SH_HP6XX && SH_ADC
644 Say Y here if you have a HP Jornada 620/660/680/690 and want to
645 support the built-in touchscreen.
647 To compile this driver as a module, choose M here: the
648 module will be called hp680_ts_input.
650 config TOUCHSCREEN_HP7XX
651 tristate "HP Jornada 7xx touchscreen"
652 depends on SA1100_JORNADA720_SSP
654 Say Y here if you have a HP Jornada 710/720/728 and want
655 to support the built-in touchscreen.
657 To compile this driver as a module, choose M here: the
658 module will be called jornada720_ts.
660 config TOUCHSCREEN_IPAQ_MICRO
661 tristate "HP iPAQ Atmel Micro ASIC touchscreen"
662 depends on MFD_IPAQ_MICRO
664 Say Y here to enable support for the touchscreen attached to
665 the Atmel Micro peripheral controller on iPAQ h3100/h3600/h3700
669 To compile this driver as a module, choose M here: the
670 module will be called ipaq-micro-ts.
672 config TOUCHSCREEN_HTCPEN
673 tristate "HTC Shift X9500 touchscreen"
676 Say Y here if you have an HTC Shift UMPC also known as HTC X9500
677 Clio / Shangrila and want to support the built-in touchscreen.
681 To compile this driver as a module, choose M here: the
682 module will be called htcpen.
684 config TOUCHSCREEN_PENMOUNT
685 tristate "Penmount serial touchscreen"
688 Say Y here if you have a Penmount serial touchscreen connected to
693 To compile this driver as a module, choose M here: the
694 module will be called penmount.
696 config TOUCHSCREEN_EDT_FT5X06
697 tristate "EDT FocalTech FT5x06 I2C Touchscreen support"
700 Say Y here if you have an EDT "Polytouch" touchscreen based
701 on the FocalTech FT5x06 family of controllers connected to
706 To compile this driver as a module, choose M here: the
707 module will be called edt-ft5x06.
709 config TOUCHSCREEN_RASPBERRYPI_FW
710 tristate "Raspberry Pi's firmware base touch screen support"
711 depends on RASPBERRYPI_FIRMWARE || (RASPBERRYPI_FIRMWARE=n && COMPILE_TEST)
713 Say Y here if you have the official Raspberry Pi 7 inch screen on
718 To compile this driver as a module, choose M here: the
719 module will be called raspberrypi-ts.
721 config TOUCHSCREEN_MIGOR
722 tristate "Renesas MIGO-R touchscreen"
723 depends on (SH_MIGOR || COMPILE_TEST) && I2C
725 Say Y here to enable MIGO-R touchscreen support.
729 To compile this driver as a module, choose M here: the
730 module will be called migor_ts.
732 config TOUCHSCREEN_TOUCHRIGHT
733 tristate "Touchright serial touchscreen"
736 Say Y here if you have a Touchright serial touchscreen connected to
741 To compile this driver as a module, choose M here: the
742 module will be called touchright.
744 config TOUCHSCREEN_TOUCHWIN
745 tristate "Touchwin serial touchscreen"
748 Say Y here if you have a Touchwin serial touchscreen connected to
753 To compile this driver as a module, choose M here: the
754 module will be called touchwin.
756 config TOUCHSCREEN_TI_AM335X_TSC
757 tristate "TI Touchscreen Interface"
758 depends on MFD_TI_AM335X_TSCADC
760 Say Y here if you have 4/5/8 wire touchscreen controller
761 to be connected to the ADC controller on your TI AM335x SoC.
765 To compile this driver as a module, choose M here: the
766 module will be called ti_am335x_tsc.
768 config TOUCHSCREEN_UCB1400
769 tristate "Philips UCB1400 touchscreen"
771 depends on UCB1400_CORE
773 This enables support for the Philips UCB1400 touchscreen interface.
774 The UCB1400 is an AC97 audio codec. The touchscreen interface
775 will be initialized only after the ALSA subsystem has been
776 brought up and the UCB1400 detected. You therefore have to
777 configure ALSA support as well (either built-in or modular,
778 independently of whether this driver is itself built-in or
779 modular) for this driver to work.
781 To compile this driver as a module, choose M here: the
782 module will be called ucb1400_ts.
784 config TOUCHSCREEN_PIXCIR
785 tristate "PIXCIR I2C touchscreens"
788 Say Y here if you have a pixcir i2c touchscreen
793 To compile this driver as a module, choose M here: the
794 module will be called pixcir_i2c_ts.
796 config TOUCHSCREEN_WDT87XX_I2C
797 tristate "Weida HiTech I2C touchscreen"
800 Say Y here if you have a Weida WDT87XX I2C touchscreen
801 connected to your system.
805 To compile this driver as a module, choose M here: the
806 module will be called wdt87xx_i2c.
808 config TOUCHSCREEN_WM831X
809 tristate "Support for WM831x touchscreen controllers"
810 depends on MFD_WM831X
812 This enables support for the touchscreen controller on the WM831x
815 To compile this driver as a module, choose M here: the
816 module will be called wm831x-ts.
818 config TOUCHSCREEN_WM97XX
819 tristate "Support for WM97xx AC97 touchscreen controllers"
820 depends on AC97_BUS || AC97_BUS_NEW
822 Say Y here if you have a Wolfson Microelectronics WM97xx
823 touchscreen connected to your system. Note that this option
824 only enables core driver, you will also need to select
825 support for appropriate chip below.
829 To compile this driver as a module, choose M here: the
830 module will be called wm97xx-ts.
832 config TOUCHSCREEN_WM9705
833 bool "WM9705 Touchscreen interface support"
834 depends on TOUCHSCREEN_WM97XX
837 Say Y here to enable support for the Wolfson Microelectronics
838 WM9705 touchscreen controller.
840 config TOUCHSCREEN_WM9712
841 bool "WM9712 Touchscreen interface support"
842 depends on TOUCHSCREEN_WM97XX
845 Say Y here to enable support for the Wolfson Microelectronics
846 WM9712 touchscreen controller.
848 config TOUCHSCREEN_WM9713
849 bool "WM9713 Touchscreen interface support"
850 depends on TOUCHSCREEN_WM97XX
853 Say Y here to enable support for the Wolfson Microelectronics
854 WM9713 touchscreen controller.
856 config TOUCHSCREEN_WM97XX_MAINSTONE
857 tristate "WM97xx Mainstone/Palm accelerated touch"
858 depends on TOUCHSCREEN_WM97XX && ARCH_PXA
860 Say Y here for support for streaming mode with WM97xx touchscreens
861 on Mainstone, Palm Tungsten T5, TX and LifeDrive systems.
865 To compile this driver as a module, choose M here: the
866 module will be called mainstone-wm97xx.
868 config TOUCHSCREEN_WM97XX_ZYLONITE
869 tristate "Zylonite accelerated touch"
870 depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE
871 select TOUCHSCREEN_WM9713
873 Say Y here for support for streaming mode with the touchscreen
878 To compile this driver as a module, choose M here: the
879 module will be called zylonite-wm97xx.
881 config TOUCHSCREEN_USB_COMPOSITE
882 tristate "USB Touchscreen Driver"
883 depends on USB_ARCH_HAS_HCD
886 USB Touchscreen driver for:
887 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
888 - PanJit TouchSet USB
889 - 3M MicroTouch USB (EX II series)
891 - some other eTurboTouch
894 - IRTOUCHSYSTEMS/UNITOP
896 - GoTop Super_Q2/GogoPen/PenPower tablets
897 - JASTEC USB Touch Controller/DigiTech DTR-02U
898 - Zytronic controllers
899 - Elo TouchSystems 2700 IntelliTouch
900 - EasyTouch USB Touch Controller from Data Modul
901 - e2i (Mimo monitors)
903 Have a look at <http://linux.chapter7.ch/touchkit/> for
904 a usage description and the required user-space stuff.
906 To compile this driver as a module, choose M here: the
907 module will be called usbtouchscreen.
909 config TOUCHSCREEN_MXS_LRADC
910 tristate "Freescale i.MX23/i.MX28 LRADC touchscreen"
911 depends on MFD_MXS_LRADC
913 Say Y here if you have a touchscreen connected to the low-resolution
914 analog-to-digital converter (LRADC) on an i.MX23 or i.MX28 processor.
916 To compile this driver as a module, choose M here: the module will be
919 config TOUCHSCREEN_MX25
920 tristate "Freescale i.MX25 touchscreen input driver"
921 depends on MFD_MX25_TSADC
923 Enable support for touchscreen connected to your i.MX25.
925 To compile this driver as a module, choose M here: the
926 module will be called fsl-imx25-tcq.
928 config TOUCHSCREEN_MC13783
929 tristate "Freescale MC13783 touchscreen input driver"
930 depends on MFD_MC13XXX
932 Say Y here if you have an Freescale MC13783 PMIC on your
933 board and want to use its touchscreen
937 To compile this driver as a module, choose M here: the
938 module will be called mc13783_ts.
940 config TOUCHSCREEN_USB_EGALAX
942 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EXPERT
943 depends on TOUCHSCREEN_USB_COMPOSITE
945 config TOUCHSCREEN_USB_PANJIT
947 bool "PanJit device support" if EXPERT
948 depends on TOUCHSCREEN_USB_COMPOSITE
950 config TOUCHSCREEN_USB_3M
952 bool "3M/Microtouch EX II series device support" if EXPERT
953 depends on TOUCHSCREEN_USB_COMPOSITE
955 config TOUCHSCREEN_USB_ITM
957 bool "ITM device support" if EXPERT
958 depends on TOUCHSCREEN_USB_COMPOSITE
960 config TOUCHSCREEN_USB_ETURBO
962 bool "eTurboTouch (non-eGalax compatible) device support" if EXPERT
963 depends on TOUCHSCREEN_USB_COMPOSITE
965 config TOUCHSCREEN_USB_GUNZE
967 bool "Gunze AHL61 device support" if EXPERT
968 depends on TOUCHSCREEN_USB_COMPOSITE
970 config TOUCHSCREEN_USB_DMC_TSC10
972 bool "DMC TSC-10/25 device support" if EXPERT
973 depends on TOUCHSCREEN_USB_COMPOSITE
975 config TOUCHSCREEN_USB_IRTOUCH
977 bool "IRTOUCHSYSTEMS/UNITOP device support" if EXPERT
978 depends on TOUCHSCREEN_USB_COMPOSITE
980 config TOUCHSCREEN_USB_IDEALTEK
982 bool "IdealTEK URTC1000 device support" if EXPERT
983 depends on TOUCHSCREEN_USB_COMPOSITE
985 config TOUCHSCREEN_USB_GENERAL_TOUCH
987 bool "GeneralTouch Touchscreen device support" if EXPERT
988 depends on TOUCHSCREEN_USB_COMPOSITE
990 config TOUCHSCREEN_USB_GOTOP
992 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EXPERT
993 depends on TOUCHSCREEN_USB_COMPOSITE
995 config TOUCHSCREEN_USB_JASTEC
997 bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EXPERT
998 depends on TOUCHSCREEN_USB_COMPOSITE
1000 config TOUCHSCREEN_USB_ELO
1002 bool "Elo TouchSystems 2700 IntelliTouch controller device support" if EXPERT
1003 depends on TOUCHSCREEN_USB_COMPOSITE
1005 config TOUCHSCREEN_USB_E2I
1007 bool "e2i Touchscreen controller (e.g. from Mimo 740)" if EXPERT
1008 depends on TOUCHSCREEN_USB_COMPOSITE
1010 config TOUCHSCREEN_USB_ZYTRONIC
1012 bool "Zytronic controller" if EXPERT
1013 depends on TOUCHSCREEN_USB_COMPOSITE
1015 config TOUCHSCREEN_USB_ETT_TC45USB
1017 bool "ET&T USB series TC4UM/TC5UH touchscreen controller support" if EXPERT
1018 depends on TOUCHSCREEN_USB_COMPOSITE
1020 config TOUCHSCREEN_USB_NEXIO
1022 bool "NEXIO/iNexio device support" if EXPERT
1023 depends on TOUCHSCREEN_USB_COMPOSITE
1025 config TOUCHSCREEN_USB_EASYTOUCH
1027 bool "EasyTouch USB Touch controller device support" if EXPERT
1028 depends on TOUCHSCREEN_USB_COMPOSITE
1030 Say Y here if you have an EasyTouch USB Touch controller.
1033 config TOUCHSCREEN_TOUCHIT213
1034 tristate "Sahara TouchIT-213 touchscreen"
1037 Say Y here if you have a Sahara TouchIT-213 Tablet PC.
1041 To compile this driver as a module, choose M here: the
1042 module will be called touchit213.
1044 config TOUCHSCREEN_TS4800
1045 tristate "TS-4800 touchscreen"
1046 depends on HAS_IOMEM && OF
1047 depends on SOC_IMX51 || COMPILE_TEST
1050 Say Y here if you have a touchscreen on a TS-4800 board.
1052 On TS-4800, the touchscreen is not handled directly by Linux but by
1057 To compile this driver as a module, choose M here: the
1058 module will be called ts4800_ts.
1060 config TOUCHSCREEN_TSC_SERIO
1061 tristate "TSC-10/25/40 serial touchscreen support"
1064 Say Y here if you have a TSC-10, 25 or 40 serial touchscreen connected
1069 To compile this driver as a module, choose M here: the
1070 module will be called tsc40.
1072 config TOUCHSCREEN_TSC200X_CORE
1075 config TOUCHSCREEN_TSC2004
1076 tristate "TSC2004 based touchscreens"
1079 select TOUCHSCREEN_TSC200X_CORE
1081 Say Y here if you have a TSC2004 based touchscreen.
1085 To compile this driver as a module, choose M here: the
1086 module will be called tsc2004.
1088 config TOUCHSCREEN_TSC2005
1089 tristate "TSC2005 based touchscreens"
1090 depends on SPI_MASTER
1092 select TOUCHSCREEN_TSC200X_CORE
1094 Say Y here if you have a TSC2005 based touchscreen.
1098 To compile this driver as a module, choose M here: the
1099 module will be called tsc2005.
1101 config TOUCHSCREEN_TSC2007
1102 tristate "TSC2007 based touchscreens"
1105 Say Y here if you have a TSC2007 based touchscreen.
1109 To compile this driver as a module, choose M here: the
1110 module will be called tsc2007.
1112 config TOUCHSCREEN_TSC2007_IIO
1113 bool "IIO interface for external ADC input and temperature"
1114 depends on TOUCHSCREEN_TSC2007
1115 depends on IIO=y || IIO=TOUCHSCREEN_TSC2007
1117 Saying Y here adds an iio interface to the tsc2007 which
1118 provides values for the AUX input (used for e.g. battery
1119 or ambient light monitoring), temperature and raw input
1122 config TOUCHSCREEN_PCAP
1123 tristate "Motorola PCAP touchscreen"
1126 Say Y here if you have a Motorola EZX telephone and
1127 want to enable support for the built-in touchscreen.
1129 To compile this driver as a module, choose M here: the
1130 module will be called pcap_ts.
1132 config TOUCHSCREEN_RM_TS
1133 tristate "Raydium I2C Touchscreen"
1135 depends on GPIOLIB || COMPILE_TEST
1137 Say Y here if you have Raydium series I2C touchscreen,
1138 such as RM32380, connected to your system.
1142 To compile this driver as a module, choose M here: the
1143 module will be called raydium_i2c_ts.
1145 config TOUCHSCREEN_SILEAD
1146 tristate "Silead I2C touchscreen"
1149 Say Y here if you have the Silead touchscreen connected to
1154 To compile this driver as a module, choose M here: the
1155 module will be called silead.
1157 config TOUCHSCREEN_SIS_I2C
1158 tristate "SiS 9200 family I2C touchscreen"
1161 depends on GPIOLIB || COMPILE_TEST
1163 This enables support for SiS 9200 family over I2C based touchscreens.
1167 To compile this driver as a module, choose M here: the
1168 module will be called sis_i2c.
1170 config TOUCHSCREEN_ST1232
1171 tristate "Sitronix ST1232 or ST1633 touchscreen controllers"
1174 Say Y here if you want to support the Sitronix ST1232
1175 or ST1633 touchscreen controller.
1179 To compile this driver as a module, choose M here: the
1180 module will be called st1232_ts.
1182 config TOUCHSCREEN_STMFTS
1183 tristate "STMicroelectronics STMFTS touchscreen"
1185 depends on LEDS_CLASS
1187 Say Y here if you want support for STMicroelectronics
1190 To compile this driver as a module, choose M here: the
1191 module will be called stmfts.
1193 config TOUCHSCREEN_STMPE
1194 tristate "STMicroelectronics STMPE touchscreens"
1195 depends on MFD_STMPE
1196 depends on (OF || COMPILE_TEST)
1198 Say Y here if you want support for STMicroelectronics
1199 STMPE touchscreen controllers.
1201 To compile this driver as a module, choose M here: the
1202 module will be called stmpe-ts.
1204 config TOUCHSCREEN_SUN4I
1205 tristate "Allwinner sun4i resistive touchscreen controller support"
1206 depends on ARCH_SUNXI || COMPILE_TEST
1208 depends on THERMAL || !THERMAL_OF
1210 This selects support for the resistive touchscreen controller
1211 found on Allwinner sunxi SoCs.
1213 To compile this driver as a module, choose M here: the
1214 module will be called sun4i-ts.
1216 config TOUCHSCREEN_SUR40
1217 tristate "Samsung SUR40 (Surface 2.0/PixelSense) touchscreen"
1218 depends on USB && MEDIA_USB_SUPPORT && HAS_DMA
1219 depends on VIDEO_V4L2
1220 select VIDEOBUF2_DMA_SG
1222 Say Y here if you want support for the Samsung SUR40 touchscreen
1223 (also known as Microsoft Surface 2.0 or Microsoft PixelSense).
1225 To compile this driver as a module, choose M here: the
1226 module will be called sur40.
1228 config TOUCHSCREEN_SURFACE3_SPI
1229 tristate "Ntrig/Microsoft Surface 3 SPI touchscreen"
1231 depends on GPIOLIB || COMPILE_TEST
1233 Say Y here if you have the Ntrig/Microsoft SPI touchscreen
1234 controller chip as found on the Surface 3 in your system.
1238 To compile this driver as a module, choose M here: the
1239 module will be called surface3_spi.
1241 config TOUCHSCREEN_SX8654
1242 tristate "Semtech SX8654 touchscreen"
1245 Say Y here if you have a Semtech SX8654 touchscreen controller.
1249 To compile this driver as a module, choose M here: the
1250 module will be called sx8654.
1252 config TOUCHSCREEN_TPS6507X
1253 tristate "TPS6507x based touchscreens"
1256 Say Y here if you have a TPS6507x based touchscreen
1261 To compile this driver as a module, choose M here: the
1262 module will be called tps6507x_ts.
1264 config TOUCHSCREEN_ZET6223
1265 tristate "Zeitec ZET6223 touchscreen driver"
1268 Say Y here if you have a touchscreen using Zeitec ZET6223
1272 To compile this driver as a module, choose M here: the
1273 module will be called zet6223.
1275 config TOUCHSCREEN_ZFORCE
1276 tristate "Neonode zForce infrared touchscreens"
1278 depends on GPIOLIB || COMPILE_TEST
1280 Say Y here if you have a touchscreen using the zforce
1281 infraread technology from Neonode.
1285 To compile this driver as a module, choose M here: the
1286 module will be called zforce_ts.
1288 config TOUCHSCREEN_COLIBRI_VF50
1289 tristate "Toradex Colibri on board touchscreen driver"
1290 depends on IIO && VF610_ADC
1291 depends on GPIOLIB || COMPILE_TEST
1293 Say Y here if you have a Colibri VF50 and plan to use
1294 the on-board provided 4-wire touchscreen driver.
1298 To compile this driver as a module, choose M here: the
1299 module will be called colibri_vf50_ts.
1301 config TOUCHSCREEN_ROHM_BU21023
1302 tristate "ROHM BU21023/24 Dual touch support resistive touchscreens"
1305 Say Y here if you have a touchscreen using ROHM BU21023/24.
1309 To compile this driver as a module, choose M here: the
1310 module will be called bu21023_ts.
1312 config TOUCHSCREEN_IQS5XX
1313 tristate "Azoteq IQS550/572/525 trackpad/touchscreen controller"
1316 Say Y to enable support for the Azoteq IQS550/572/525
1317 family of trackpad/touchscreen controllers.
1319 To compile this driver as a module, choose M here: the
1320 module will be called iqs5xx.
1322 config TOUCHSCREEN_ZINITIX
1323 tristate "Zinitix touchscreen support"
1326 Say Y here if you have a touchscreen using Zinitix bt541,
1327 or something similar enough.
1331 To compile this driver as a module, choose M here: the
1332 module will be called zinitix.