drivers/i2c/busses/i2c-exynos5.c

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * i2c-exynos5.c - Samsung Exynos5 I2C Controller Driver
   4  *
   5  * Copyright (C) 2013 Samsung Electronics Co., Ltd.
   6 */
   7
   8 #include <linux/kernel.h>
   9 #include <linux/module.h>
  10
  11 #include <linux/i2c.h>
  12 #include <linux/time.h>
  13 #include <linux/interrupt.h>
  14 #include <linux/delay.h>
  15 #include <linux/errno.h>
  16 #include <linux/err.h>
  17 #include <linux/platform_device.h>
  18 #include <linux/clk.h>
  19 #include <linux/slab.h>
  20 #include <linux/io.h>
  21 #include <linux/of_address.h>
  22 #include <linux/of_device.h>
  23 #include <linux/of_irq.h>
  24 #include <linux/spinlock.h>
  25
  26 /*
  27  * HSI2C controller from Samsung supports 2 modes of operation
  28  * 1. Auto mode: Where in master automatically controls the whole transaction
  29  * 2. Manual mode: Software controls the transaction by issuing commands
  30  *    START, READ, WRITE, STOP, RESTART in I2C_MANUAL_CMD register.
  31  *
  32  * Operation mode can be selected by setting AUTO_MODE bit in I2C_CONF register
  33  *
  34  * Special bits are available for both modes of operation to set commands
  35  * and for checking transfer status
  36  */
  37
  38 /* Register Map */
  39 #define HSI2C_CTL               0x00
  40 #define HSI2C_FIFO_CTL          0x04
  41 #define HSI2C_TRAILIG_CTL       0x08
  42 #define HSI2C_CLK_CTL           0x0C
  43 #define HSI2C_CLK_SLOT          0x10
  44 #define HSI2C_INT_ENABLE        0x20
  45 #define HSI2C_INT_STATUS        0x24
  46 #define HSI2C_ERR_STATUS        0x2C
  47 #define HSI2C_FIFO_STATUS       0x30
  48 #define HSI2C_TX_DATA           0x34
  49 #define HSI2C_RX_DATA           0x38
  50 #define HSI2C_CONF              0x40
  51 #define HSI2C_AUTO_CONF         0x44
  52 #define HSI2C_TIMEOUT           0x48
  53 #define HSI2C_MANUAL_CMD        0x4C
  54 #define HSI2C_TRANS_STATUS      0x50
  55 #define HSI2C_TIMING_HS1        0x54
  56 #define HSI2C_TIMING_HS2        0x58
  57 #define HSI2C_TIMING_HS3        0x5C
  58 #define HSI2C_TIMING_FS1        0x60
  59 #define HSI2C_TIMING_FS2        0x64
  60 #define HSI2C_TIMING_FS3        0x68
  61 #define HSI2C_TIMING_SLA        0x6C
  62 #define HSI2C_ADDR              0x70
  63
  64 /* I2C_CTL Register bits */
  65 #define HSI2C_FUNC_MODE_I2C                     (1u << 0)
  66 #define HSI2C_MASTER                            (1u << 3)
  67 #define HSI2C_RXCHON                            (1u << 6)
  68 #define HSI2C_TXCHON                            (1u << 7)
  69 #define HSI2C_SW_RST                            (1u << 31)
  70
  71 /* I2C_FIFO_CTL Register bits */
  72 #define HSI2C_RXFIFO_EN                         (1u << 0)
  73 #define HSI2C_TXFIFO_EN                         (1u << 1)
  74 #define HSI2C_RXFIFO_TRIGGER_LEVEL(x)           ((x) << 4)
  75 #define HSI2C_TXFIFO_TRIGGER_LEVEL(x)           ((x) << 16)
  76
  77 /* I2C_TRAILING_CTL Register bits */
  78 #define HSI2C_TRAILING_COUNT                    (0xf)
  79
  80 /* I2C_INT_EN Register bits */
  81 #define HSI2C_INT_TX_ALMOSTEMPTY_EN             (1u << 0)
  82 #define HSI2C_INT_RX_ALMOSTFULL_EN              (1u << 1)
  83 #define HSI2C_INT_TRAILING_EN                   (1u << 6)
  84
  85 /* I2C_INT_STAT Register bits */
  86 #define HSI2C_INT_TX_ALMOSTEMPTY                (1u << 0)
  87 #define HSI2C_INT_RX_ALMOSTFULL                 (1u << 1)
  88 #define HSI2C_INT_TX_UNDERRUN                   (1u << 2)
  89 #define HSI2C_INT_TX_OVERRUN                    (1u << 3)
  90 #define HSI2C_INT_RX_UNDERRUN                   (1u << 4)
  91 #define HSI2C_INT_RX_OVERRUN                    (1u << 5)
  92 #define HSI2C_INT_TRAILING                      (1u << 6)
  93 #define HSI2C_INT_I2C                           (1u << 9)
  94
  95 #define HSI2C_INT_TRANS_DONE                    (1u << 7)
  96 #define HSI2C_INT_TRANS_ABORT                   (1u << 8)
  97 #define HSI2C_INT_NO_DEV_ACK                    (1u << 9)
  98 #define HSI2C_INT_NO_DEV                        (1u << 10)
  99 #define HSI2C_INT_TIMEOUT                       (1u << 11)
 100 #define HSI2C_INT_I2C_TRANS                     (HSI2C_INT_TRANS_DONE | \
 101                                                 HSI2C_INT_TRANS_ABORT | \
 102                                                 HSI2C_INT_NO_DEV_ACK |  \
 103                                                 HSI2C_INT_NO_DEV |      \
 104                                                 HSI2C_INT_TIMEOUT)
 105
 106 /* I2C_FIFO_STAT Register bits */
 107 #define HSI2C_RX_FIFO_EMPTY                     (1u << 24)
 108 #define HSI2C_RX_FIFO_FULL                      (1u << 23)
 109 #define HSI2C_RX_FIFO_LVL(x)                    ((x >> 16) & 0x7f)
 110 #define HSI2C_TX_FIFO_EMPTY                     (1u << 8)
 111 #define HSI2C_TX_FIFO_FULL                      (1u << 7)
 112 #define HSI2C_TX_FIFO_LVL(x)                    ((x >> 0) & 0x7f)
 113
 114 /* I2C_CONF Register bits */
 115 #define HSI2C_AUTO_MODE                         (1u << 31)
 116 #define HSI2C_10BIT_ADDR_MODE                   (1u << 30)
 117 #define HSI2C_HS_MODE                           (1u << 29)
 118
 119 /* I2C_AUTO_CONF Register bits */
 120 #define HSI2C_READ_WRITE                        (1u << 16)
 121 #define HSI2C_STOP_AFTER_TRANS                  (1u << 17)
 122 #define HSI2C_MASTER_RUN                        (1u << 31)
 123
 124 /* I2C_TIMEOUT Register bits */
 125 #define HSI2C_TIMEOUT_EN                        (1u << 31)
 126 #define HSI2C_TIMEOUT_MASK                      0xff
 127
 128 /* I2C_MANUAL_CMD register bits */
 129 #define HSI2C_CMD_READ_DATA                     (1u << 4)
 130 #define HSI2C_CMD_SEND_STOP                     (1u << 2)
 131
 132 /* I2C_TRANS_STATUS register bits */
 133 #define HSI2C_MASTER_BUSY                       (1u << 17)
 134 #define HSI2C_SLAVE_BUSY                        (1u << 16)
 135
 136 /* I2C_TRANS_STATUS register bits for Exynos5 variant */
 137 #define HSI2C_TIMEOUT_AUTO                      (1u << 4)
 138 #define HSI2C_NO_DEV                            (1u << 3)
 139 #define HSI2C_NO_DEV_ACK                        (1u << 2)
 140 #define HSI2C_TRANS_ABORT                       (1u << 1)
 141 #define HSI2C_TRANS_DONE                        (1u << 0)
 142
 143 /* I2C_TRANS_STATUS register bits for Exynos7 variant */
 144 #define HSI2C_MASTER_ST_MASK                    0xf
 145 #define HSI2C_MASTER_ST_IDLE                    0x0
 146 #define HSI2C_MASTER_ST_START                   0x1
 147 #define HSI2C_MASTER_ST_RESTART                 0x2
 148 #define HSI2C_MASTER_ST_STOP                    0x3
 149 #define HSI2C_MASTER_ST_MASTER_ID               0x4
 150 #define HSI2C_MASTER_ST_ADDR0                   0x5
 151 #define HSI2C_MASTER_ST_ADDR1                   0x6
 152 #define HSI2C_MASTER_ST_ADDR2                   0x7
 153 #define HSI2C_MASTER_ST_ADDR_SR                 0x8
 154 #define HSI2C_MASTER_ST_READ                    0x9
 155 #define HSI2C_MASTER_ST_WRITE                   0xa
 156 #define HSI2C_MASTER_ST_NO_ACK                  0xb
 157 #define HSI2C_MASTER_ST_LOSE                    0xc
 158 #define HSI2C_MASTER_ST_WAIT                    0xd
 159 #define HSI2C_MASTER_ST_WAIT_CMD                0xe
 160
 161 /* I2C_ADDR register bits */
 162 #define HSI2C_SLV_ADDR_SLV(x)                   ((x & 0x3ff) << 0)
 163 #define HSI2C_SLV_ADDR_MAS(x)                   ((x & 0x3ff) << 10)
 164 #define HSI2C_MASTER_ID(x)                      ((x & 0xff) << 24)
 165 #define MASTER_ID(x)                            ((x & 0x7) + 0x08)
 166
 167 #define EXYNOS5_I2C_TIMEOUT (msecs_to_jiffies(100))
 168
 169 enum i2c_type_exynos {
 170         I2C_TYPE_EXYNOS5,
 171         I2C_TYPE_EXYNOS7,
 172 };
 173
 174 struct exynos5_i2c {
 175         struct i2c_adapter      adap;
 176
 177         struct i2c_msg          *msg;
 178         struct completion       msg_complete;
 179         unsigned int            msg_ptr;
 180
 181         unsigned int            irq;
 182
 183         void __iomem            *regs;
 184         struct clk              *clk;
 185         struct device           *dev;
 186         int                     state;
 187
 188         spinlock_t              lock;           /* IRQ synchronization */
 189
 190         /*
 191          * Since the TRANS_DONE bit is cleared on read, and we may read it
 192          * either during an IRQ or after a transaction, keep track of its
 193          * state here.
 194          */
 195         int                     trans_done;
 196
 197         /* Controller operating frequency */
 198         unsigned int            op_clock;
 199
 200         /* Version of HS-I2C Hardware */
 201         const struct exynos_hsi2c_variant *variant;
 202 };
 203
 204 /**
 205  * struct exynos_hsi2c_variant - platform specific HSI2C driver data
 206  * @fifo_depth: the fifo depth supported by the HSI2C module
 207  * @hw: the hardware variant of Exynos I2C controller
 208  *
 209  * Specifies platform specific configuration of HSI2C module.
 210  * Note: A structure for driver specific platform data is used for future
 211  * expansion of its usage.
 212  */
 213 struct exynos_hsi2c_variant {
 214         unsigned int            fifo_depth;
 215         enum i2c_type_exynos    hw;
 216 };
 217
 218 static const struct exynos_hsi2c_variant exynos5250_hsi2c_data = {
 219         .fifo_depth     = 64,
 220         .hw             = I2C_TYPE_EXYNOS5,
 221 };
 222
 223 static const struct exynos_hsi2c_variant exynos5260_hsi2c_data = {
 224         .fifo_depth     = 16,
 225         .hw             = I2C_TYPE_EXYNOS5,
 226 };
 227
 228 static const struct exynos_hsi2c_variant exynos7_hsi2c_data = {
 229         .fifo_depth     = 16,
 230         .hw             = I2C_TYPE_EXYNOS7,
 231 };
 232
 233 static const struct of_device_id exynos5_i2c_match[] = {
 234         {
 235                 .compatible = "samsung,exynos5-hsi2c",
 236                 .data = &exynos5250_hsi2c_data
 237         }, {
 238                 .compatible = "samsung,exynos5250-hsi2c",
 239                 .data = &exynos5250_hsi2c_data
 240         }, {
 241                 .compatible = "samsung,exynos5260-hsi2c",
 242                 .data = &exynos5260_hsi2c_data
 243         }, {
 244                 .compatible = "samsung,exynos7-hsi2c",
 245                 .data = &exynos7_hsi2c_data
 246         }, {},
 247 };
 248 MODULE_DEVICE_TABLE(of, exynos5_i2c_match);
 249
 250 static void exynos5_i2c_clr_pend_irq(struct exynos5_i2c *i2c)
 251 {
 252         writel(readl(i2c->regs + HSI2C_INT_STATUS),
 253                                 i2c->regs + HSI2C_INT_STATUS);
 254 }
 255
 256 /*
 257  * exynos5_i2c_set_timing: updates the registers with appropriate
 258  * timing values calculated
 259  *
 260  * Timing values for operation are calculated against either 100kHz
 261  * or 1MHz controller operating frequency.
 262  *
 263  * Returns 0 on success, -EINVAL if the cycle length cannot
 264  * be calculated.
 265  */
 266 static int exynos5_i2c_set_timing(struct exynos5_i2c *i2c, bool hs_timings)
 267 {
 268         u32 i2c_timing_s1;
 269         u32 i2c_timing_s2;
 270         u32 i2c_timing_s3;
 271         u32 i2c_timing_sla;
 272         unsigned int t_start_su, t_start_hd;
 273         unsigned int t_stop_su;
 274         unsigned int t_data_su, t_data_hd;
 275         unsigned int t_scl_l, t_scl_h;
 276         unsigned int t_sr_release;
 277         unsigned int t_ftl_cycle;
 278         unsigned int clkin = clk_get_rate(i2c->clk);
 279         unsigned int op_clk = hs_timings ? i2c->op_clock :
 280                 (i2c->op_clock >= I2C_MAX_FAST_MODE_PLUS_FREQ) ? I2C_MAX_STANDARD_MODE_FREQ :
 281                 i2c->op_clock;
 282         int div, clk_cycle, temp;
 283
 284         /*
 285          * In case of HSI2C controller in Exynos5 series
 286          * FPCLK / FI2C =
 287          * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + 2 * FLT_CYCLE
 288          *
 289          * In case of HSI2C controllers in Exynos7 series
 290          * FPCLK / FI2C =
 291          * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + FLT_CYCLE
 292          *
 293          * clk_cycle := TSCLK_L + TSCLK_H
 294          * temp := (CLK_DIV + 1) * (clk_cycle + 2)
 295          *
 296          * Constraints: 4 <= temp, 0 <= CLK_DIV < 256, 2 <= clk_cycle <= 510
 297          *
 298          */
 299         t_ftl_cycle = (readl(i2c->regs + HSI2C_CONF) >> 16) & 0x7;
 300         temp = clkin / op_clk - 8 - t_ftl_cycle;
 301         if (i2c->variant->hw != I2C_TYPE_EXYNOS7)
 302                 temp -= t_ftl_cycle;
 303         div = temp / 512;
 304         clk_cycle = temp / (div + 1) - 2;
 305         if (temp < 4 || div >= 256 || clk_cycle < 2) {
 306                 dev_err(i2c->dev, "%s clock set-up failed\n",
 307                         hs_timings ? "HS" : "FS");
 308                 return -EINVAL;
 309         }
 310
 311         t_scl_l = clk_cycle / 2;
 312         t_scl_h = clk_cycle / 2;
 313         t_start_su = t_scl_l;
 314         t_start_hd = t_scl_l;
 315         t_stop_su = t_scl_l;
 316         t_data_su = t_scl_l / 2;
 317         t_data_hd = t_scl_l / 2;
 318         t_sr_release = clk_cycle;
 319
 320         i2c_timing_s1 = t_start_su << 24 | t_start_hd << 16 | t_stop_su << 8;
 321         i2c_timing_s2 = t_data_su << 24 | t_scl_l << 8 | t_scl_h << 0;
 322         i2c_timing_s3 = div << 16 | t_sr_release << 0;
 323         i2c_timing_sla = t_data_hd << 0;
 324
 325         dev_dbg(i2c->dev, "tSTART_SU: %X, tSTART_HD: %X, tSTOP_SU: %X\n",
 326                 t_start_su, t_start_hd, t_stop_su);
 327         dev_dbg(i2c->dev, "tDATA_SU: %X, tSCL_L: %X, tSCL_H: %X\n",
 328                 t_data_su, t_scl_l, t_scl_h);
 329         dev_dbg(i2c->dev, "nClkDiv: %X, tSR_RELEASE: %X\n",
 330                 div, t_sr_release);
 331         dev_dbg(i2c->dev, "tDATA_HD: %X\n", t_data_hd);
 332
 333         if (hs_timings) {
 334                 writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_HS1);
 335                 writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_HS2);
 336                 writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_HS3);
 337         } else {
 338                 writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_FS1);
 339                 writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_FS2);
 340                 writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_FS3);
 341         }
 342         writel(i2c_timing_sla, i2c->regs + HSI2C_TIMING_SLA);
 343
 344         return 0;
 345 }
 346
 347 static int exynos5_hsi2c_clock_setup(struct exynos5_i2c *i2c)
 348 {
 349         /* always set Fast Speed timings */
 350         int ret = exynos5_i2c_set_timing(i2c, false);
 351
 352         if (ret < 0 || i2c->op_clock < I2C_MAX_FAST_MODE_PLUS_FREQ)
 353                 return ret;
 354
 355         return exynos5_i2c_set_timing(i2c, true);
 356 }
 357
 358 /*
 359  * exynos5_i2c_init: configures the controller for I2C functionality
 360  * Programs I2C controller for Master mode operation
 361  */
 362 static void exynos5_i2c_init(struct exynos5_i2c *i2c)
 363 {
 364         u32 i2c_conf = readl(i2c->regs + HSI2C_CONF);
 365         u32 i2c_timeout = readl(i2c->regs + HSI2C_TIMEOUT);
 366
 367         /* Clear to disable Timeout */
 368         i2c_timeout &= ~HSI2C_TIMEOUT_EN;
 369         writel(i2c_timeout, i2c->regs + HSI2C_TIMEOUT);
 370
 371         writel((HSI2C_FUNC_MODE_I2C | HSI2C_MASTER),
 372                                         i2c->regs + HSI2C_CTL);
 373         writel(HSI2C_TRAILING_COUNT, i2c->regs + HSI2C_TRAILIG_CTL);
 374
 375         if (i2c->op_clock >= I2C_MAX_FAST_MODE_PLUS_FREQ) {
 376                 writel(HSI2C_MASTER_ID(MASTER_ID(i2c->adap.nr)),
 377                                         i2c->regs + HSI2C_ADDR);
 378                 i2c_conf |= HSI2C_HS_MODE;
 379         }
 380
 381         writel(i2c_conf | HSI2C_AUTO_MODE, i2c->regs + HSI2C_CONF);
 382 }
 383
 384 static void exynos5_i2c_reset(struct exynos5_i2c *i2c)
 385 {
 386         u32 i2c_ctl;
 387
 388         /* Set and clear the bit for reset */
 389         i2c_ctl = readl(i2c->regs + HSI2C_CTL);
 390         i2c_ctl |= HSI2C_SW_RST;
 391         writel(i2c_ctl, i2c->regs + HSI2C_CTL);
 392
 393         i2c_ctl = readl(i2c->regs + HSI2C_CTL);
 394         i2c_ctl &= ~HSI2C_SW_RST;
 395         writel(i2c_ctl, i2c->regs + HSI2C_CTL);
 396
 397         /* We don't expect calculations to fail during the run */
 398         exynos5_hsi2c_clock_setup(i2c);
 399         /* Initialize the configure registers */
 400         exynos5_i2c_init(i2c);
 401 }
 402
 403 /*
 404  * exynos5_i2c_irq: top level IRQ servicing routine
 405  *
 406  * INT_STATUS registers gives the interrupt details. Further,
 407  * FIFO_STATUS or TRANS_STATUS registers are to be check for detailed
 408  * state of the bus.
 409  */
 410 static irqreturn_t exynos5_i2c_irq(int irqno, void *dev_id)
 411 {
 412         struct exynos5_i2c *i2c = dev_id;
 413         u32 fifo_level, int_status, fifo_status, trans_status;
 414         unsigned char byte;
 415         int len = 0;
 416
 417         i2c->state = -EINVAL;
 418
 419         spin_lock(&i2c->lock);
 420
 421         int_status = readl(i2c->regs + HSI2C_INT_STATUS);
 422         writel(int_status, i2c->regs + HSI2C_INT_STATUS);
 423
 424         /* handle interrupt related to the transfer status */
 425         if (i2c->variant->hw == I2C_TYPE_EXYNOS7) {
 426                 if (int_status & HSI2C_INT_TRANS_DONE) {
 427                         i2c->trans_done = 1;
 428                         i2c->state = 0;
 429                 } else if (int_status & HSI2C_INT_TRANS_ABORT) {
 430                         dev_dbg(i2c->dev, "Deal with arbitration lose\n");
 431                         i2c->state = -EAGAIN;
 432                         goto stop;
 433                 } else if (int_status & HSI2C_INT_NO_DEV_ACK) {
 434                         dev_dbg(i2c->dev, "No ACK from device\n");
 435                         i2c->state = -ENXIO;
 436                         goto stop;
 437                 } else if (int_status & HSI2C_INT_NO_DEV) {
 438                         dev_dbg(i2c->dev, "No device\n");
 439                         i2c->state = -ENXIO;
 440                         goto stop;
 441                 } else if (int_status & HSI2C_INT_TIMEOUT) {
 442                         dev_dbg(i2c->dev, "Accessing device timed out\n");
 443                         i2c->state = -ETIMEDOUT;
 444                         goto stop;
 445                 }
 446         } else if (int_status & HSI2C_INT_I2C) {
 447                 trans_status = readl(i2c->regs + HSI2C_TRANS_STATUS);
 448                 if (trans_status & HSI2C_NO_DEV_ACK) {
 449                         dev_dbg(i2c->dev, "No ACK from device\n");
 450                         i2c->state = -ENXIO;
 451                         goto stop;
 452                 } else if (trans_status & HSI2C_NO_DEV) {
 453                         dev_dbg(i2c->dev, "No device\n");
 454                         i2c->state = -ENXIO;
 455                         goto stop;
 456                 } else if (trans_status & HSI2C_TRANS_ABORT) {
 457                         dev_dbg(i2c->dev, "Deal with arbitration lose\n");
 458                         i2c->state = -EAGAIN;
 459                         goto stop;
 460                 } else if (trans_status & HSI2C_TIMEOUT_AUTO) {
 461                         dev_dbg(i2c->dev, "Accessing device timed out\n");
 462                         i2c->state = -ETIMEDOUT;
 463                         goto stop;
 464                 } else if (trans_status & HSI2C_TRANS_DONE) {
 465                         i2c->trans_done = 1;
 466                         i2c->state = 0;
 467                 }
 468         }
 469
 470         if ((i2c->msg->flags & I2C_M_RD) && (int_status &
 471                         (HSI2C_INT_TRAILING | HSI2C_INT_RX_ALMOSTFULL))) {
 472                 fifo_status = readl(i2c->regs + HSI2C_FIFO_STATUS);
 473                 fifo_level = HSI2C_RX_FIFO_LVL(fifo_status);
 474                 len = min(fifo_level, i2c->msg->len - i2c->msg_ptr);
 475
 476                 while (len > 0) {
 477                         byte = (unsigned char)
 478                                 readl(i2c->regs + HSI2C_RX_DATA);
 479                         i2c->msg->buf[i2c->msg_ptr++] = byte;
 480                         len--;
 481                 }
 482                 i2c->state = 0;
 483         } else if (int_status & HSI2C_INT_TX_ALMOSTEMPTY) {
 484                 fifo_status = readl(i2c->regs + HSI2C_FIFO_STATUS);
 485                 fifo_level = HSI2C_TX_FIFO_LVL(fifo_status);
 486
 487                 len = i2c->variant->fifo_depth - fifo_level;
 488                 if (len > (i2c->msg->len - i2c->msg_ptr)) {
 489                         u32 int_en = readl(i2c->regs + HSI2C_INT_ENABLE);
 490
 491                         int_en &= ~HSI2C_INT_TX_ALMOSTEMPTY_EN;
 492                         writel(int_en, i2c->regs + HSI2C_INT_ENABLE);
 493                         len = i2c->msg->len - i2c->msg_ptr;
 494                 }
 495
 496                 while (len > 0) {
 497                         byte = i2c->msg->buf[i2c->msg_ptr++];
 498                         writel(byte, i2c->regs + HSI2C_TX_DATA);
 499                         len--;
 500                 }
 501                 i2c->state = 0;
 502         }
 503
 504  stop:
 505         if ((i2c->trans_done && (i2c->msg->len == i2c->msg_ptr)) ||
 506             (i2c->state < 0)) {
 507                 writel(0, i2c->regs + HSI2C_INT_ENABLE);
 508                 exynos5_i2c_clr_pend_irq(i2c);
 509                 complete(&i2c->msg_complete);
 510         }
 511
 512         spin_unlock(&i2c->lock);
 513
 514         return IRQ_HANDLED;
 515 }
 516
 517 /*
 518  * exynos5_i2c_wait_bus_idle
 519  *
 520  * Wait for the bus to go idle, indicated by the MASTER_BUSY bit being
 521  * cleared.
 522  *
 523  * Returns -EBUSY if the bus cannot be bought to idle
 524  */
 525 static int exynos5_i2c_wait_bus_idle(struct exynos5_i2c *i2c)
 526 {
 527         unsigned long stop_time;
 528         u32 trans_status;
 529
 530         /* wait for 100 milli seconds for the bus to be idle */
 531         stop_time = jiffies + msecs_to_jiffies(100) + 1;
 532         do {
 533                 trans_status = readl(i2c->regs + HSI2C_TRANS_STATUS);
 534                 if (!(trans_status & HSI2C_MASTER_BUSY))
 535                         return 0;
 536
 537                 usleep_range(50, 200);
 538         } while (time_before(jiffies, stop_time));
 539
 540         return -EBUSY;
 541 }
 542
 543 static void exynos5_i2c_bus_recover(struct exynos5_i2c *i2c)
 544 {
 545         u32 val;
 546
 547         val = readl(i2c->regs + HSI2C_CTL) | HSI2C_RXCHON;
 548         writel(val, i2c->regs + HSI2C_CTL);
 549         val = readl(i2c->regs + HSI2C_CONF) & ~HSI2C_AUTO_MODE;
 550         writel(val, i2c->regs + HSI2C_CONF);
 551
 552         /*
 553          * Specification says master should send nine clock pulses. It can be
 554          * emulated by sending manual read command (nine pulses for read eight
 555          * bits + one pulse for NACK).
 556          */
 557         writel(HSI2C_CMD_READ_DATA, i2c->regs + HSI2C_MANUAL_CMD);
 558         exynos5_i2c_wait_bus_idle(i2c);
 559         writel(HSI2C_CMD_SEND_STOP, i2c->regs + HSI2C_MANUAL_CMD);
 560         exynos5_i2c_wait_bus_idle(i2c);
 561
 562         val = readl(i2c->regs + HSI2C_CTL) & ~HSI2C_RXCHON;
 563         writel(val, i2c->regs + HSI2C_CTL);
 564         val = readl(i2c->regs + HSI2C_CONF) | HSI2C_AUTO_MODE;
 565         writel(val, i2c->regs + HSI2C_CONF);
 566 }
 567
 568 static void exynos5_i2c_bus_check(struct exynos5_i2c *i2c)
 569 {
 570         unsigned long timeout;
 571
 572         if (i2c->variant->hw != I2C_TYPE_EXYNOS7)
 573                 return;
 574
 575         /*
 576          * HSI2C_MASTER_ST_LOSE state in EXYNOS7 variant before transaction
 577          * indicates that bus is stuck (SDA is low). In such case bus recovery
 578          * can be performed.
 579          */
 580         timeout = jiffies + msecs_to_jiffies(100);
 581         for (;;) {
 582                 u32 st = readl(i2c->regs + HSI2C_TRANS_STATUS);
 583
 584                 if ((st & HSI2C_MASTER_ST_MASK) != HSI2C_MASTER_ST_LOSE)
 585                         return;
 586
 587                 if (time_is_before_jiffies(timeout))
 588                         return;
 589
 590                 exynos5_i2c_bus_recover(i2c);
 591         }
 592 }
 593
 594 /*
 595  * exynos5_i2c_message_start: Configures the bus and starts the xfer
 596  * i2c: struct exynos5_i2c pointer for the current bus
 597  * stop: Enables stop after transfer if set. Set for last transfer of
 598  *       in the list of messages.
 599  *
 600  * Configures the bus for read/write function
 601  * Sets chip address to talk to, message length to be sent.
 602  * Enables appropriate interrupts and sends start xfer command.
 603  */
 604 static void exynos5_i2c_message_start(struct exynos5_i2c *i2c, int stop)
 605 {
 606         u32 i2c_ctl;
 607         u32 int_en = 0;
 608         u32 i2c_auto_conf = 0;
 609         u32 i2c_addr = 0;
 610         u32 fifo_ctl;
 611         unsigned long flags;
 612         unsigned short trig_lvl;
 613
 614         if (i2c->variant->hw == I2C_TYPE_EXYNOS7)
 615                 int_en |= HSI2C_INT_I2C_TRANS;
 616         else
 617                 int_en |= HSI2C_INT_I2C;
 618
 619         i2c_ctl = readl(i2c->regs + HSI2C_CTL);
 620         i2c_ctl &= ~(HSI2C_TXCHON | HSI2C_RXCHON);
 621         fifo_ctl = HSI2C_RXFIFO_EN | HSI2C_TXFIFO_EN;
 622
 623         if (i2c->msg->flags & I2C_M_RD) {
 624                 i2c_ctl |= HSI2C_RXCHON;
 625
 626                 i2c_auto_conf |= HSI2C_READ_WRITE;
 627
 628                 trig_lvl = (i2c->msg->len > i2c->variant->fifo_depth) ?
 629                         (i2c->variant->fifo_depth * 3 / 4) : i2c->msg->len;
 630                 fifo_ctl |= HSI2C_RXFIFO_TRIGGER_LEVEL(trig_lvl);
 631
 632                 int_en |= (HSI2C_INT_RX_ALMOSTFULL_EN |
 633                         HSI2C_INT_TRAILING_EN);
 634         } else {
 635                 i2c_ctl |= HSI2C_TXCHON;
 636
 637                 trig_lvl = (i2c->msg->len > i2c->variant->fifo_depth) ?
 638                         (i2c->variant->fifo_depth * 1 / 4) : i2c->msg->len;
 639                 fifo_ctl |= HSI2C_TXFIFO_TRIGGER_LEVEL(trig_lvl);
 640
 641                 int_en |= HSI2C_INT_TX_ALMOSTEMPTY_EN;
 642         }
 643
 644         i2c_addr = HSI2C_SLV_ADDR_MAS(i2c->msg->addr);
 645
 646         if (i2c->op_clock >= I2C_MAX_FAST_MODE_PLUS_FREQ)
 647                 i2c_addr |= HSI2C_MASTER_ID(MASTER_ID(i2c->adap.nr));
 648
 649         writel(i2c_addr, i2c->regs + HSI2C_ADDR);
 650
 651         writel(fifo_ctl, i2c->regs + HSI2C_FIFO_CTL);
 652         writel(i2c_ctl, i2c->regs + HSI2C_CTL);
 653
 654         exynos5_i2c_bus_check(i2c);
 655
 656         /*
 657          * Enable interrupts before starting the transfer so that we don't
 658          * miss any INT_I2C interrupts.
 659          */
 660         spin_lock_irqsave(&i2c->lock, flags);
 661         writel(int_en, i2c->regs + HSI2C_INT_ENABLE);
 662
 663         if (stop == 1)
 664                 i2c_auto_conf |= HSI2C_STOP_AFTER_TRANS;
 665         i2c_auto_conf |= i2c->msg->len;
 666         i2c_auto_conf |= HSI2C_MASTER_RUN;
 667         writel(i2c_auto_conf, i2c->regs + HSI2C_AUTO_CONF);
 668         spin_unlock_irqrestore(&i2c->lock, flags);
 669 }
 670
 671 static int exynos5_i2c_xfer_msg(struct exynos5_i2c *i2c,
 672                               struct i2c_msg *msgs, int stop)
 673 {
 674         unsigned long timeout;
 675         int ret;
 676
 677         i2c->msg = msgs;
 678         i2c->msg_ptr = 0;
 679         i2c->trans_done = 0;
 680
 681         reinit_completion(&i2c->msg_complete);
 682
 683         exynos5_i2c_message_start(i2c, stop);
 684
 685         timeout = wait_for_completion_timeout(&i2c->msg_complete,
 686                                               EXYNOS5_I2C_TIMEOUT);
 687         if (timeout == 0)
 688                 ret = -ETIMEDOUT;
 689         else
 690                 ret = i2c->state;
 691
 692         /*
 693          * If this is the last message to be transfered (stop == 1)
 694          * Then check if the bus can be brought back to idle.
 695          */
 696         if (ret == 0 && stop)
 697                 ret = exynos5_i2c_wait_bus_idle(i2c);
 698
 699         if (ret < 0) {
 700                 exynos5_i2c_reset(i2c);
 701                 if (ret == -ETIMEDOUT)
 702                         dev_warn(i2c->dev, "%s timeout\n",
 703                                  (msgs->flags & I2C_M_RD) ? "rx" : "tx");
 704         }
 705
 706         /* Return the state as in interrupt routine */
 707         return ret;
 708 }
 709
 710 static int exynos5_i2c_xfer(struct i2c_adapter *adap,
 711                         struct i2c_msg *msgs, int num)
 712 {
 713         struct exynos5_i2c *i2c = adap->algo_data;
 714         int i, ret;
 715
 716         ret = clk_enable(i2c->clk);
 717         if (ret)
 718                 return ret;
 719
 720         for (i = 0; i < num; ++i) {
 721                 ret = exynos5_i2c_xfer_msg(i2c, msgs + i, i + 1 == num);
 722                 if (ret)
 723                         break;
 724         }
 725
 726         clk_disable(i2c->clk);
 727
 728         return ret ?: num;
 729 }
 730
 731 static u32 exynos5_i2c_func(struct i2c_adapter *adap)
 732 {
 733         return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK);
 734 }
 735
 736 static const struct i2c_algorithm exynos5_i2c_algorithm = {
 737         .master_xfer            = exynos5_i2c_xfer,
 738         .functionality          = exynos5_i2c_func,
 739 };
 740
 741 static int exynos5_i2c_probe(struct platform_device *pdev)
 742 {
 743         struct device_node *np = pdev->dev.of_node;
 744         struct exynos5_i2c *i2c;
 745         int ret;
 746
 747         i2c = devm_kzalloc(&pdev->dev, sizeof(struct exynos5_i2c), GFP_KERNEL);
 748         if (!i2c)
 749                 return -ENOMEM;
 750
 751         if (of_property_read_u32(np, "clock-frequency", &i2c->op_clock))
 752                 i2c->op_clock = I2C_MAX_STANDARD_MODE_FREQ;
 753
 754         strlcpy(i2c->adap.name, "exynos5-i2c", sizeof(i2c->adap.name));
 755         i2c->adap.owner   = THIS_MODULE;
 756         i2c->adap.algo    = &exynos5_i2c_algorithm;
 757         i2c->adap.retries = 3;
 758
 759         i2c->dev = &pdev->dev;
 760         i2c->clk = devm_clk_get(&pdev->dev, "hsi2c");
 761         if (IS_ERR(i2c->clk)) {
 762                 dev_err(&pdev->dev, "cannot get clock\n");
 763                 return -ENOENT;
 764         }
 765
 766         ret = clk_prepare_enable(i2c->clk);
 767         if (ret)
 768                 return ret;
 769
 770         i2c->regs = devm_platform_ioremap_resource(pdev, 0);
 771         if (IS_ERR(i2c->regs)) {
 772                 ret = PTR_ERR(i2c->regs);
 773                 goto err_clk;
 774         }
 775
 776         i2c->adap.dev.of_node = np;
 777         i2c->adap.algo_data = i2c;
 778         i2c->adap.dev.parent = &pdev->dev;
 779
 780         /* Clear pending interrupts from u-boot or misc causes */
 781         exynos5_i2c_clr_pend_irq(i2c);
 782
 783         spin_lock_init(&i2c->lock);
 784         init_completion(&i2c->msg_complete);
 785
 786         i2c->irq = ret = platform_get_irq(pdev, 0);
 787         if (ret < 0)
 788                 goto err_clk;
 789
 790         ret = devm_request_irq(&pdev->dev, i2c->irq, exynos5_i2c_irq,
 791                                IRQF_NO_SUSPEND, dev_name(&pdev->dev), i2c);
 792         if (ret != 0) {
 793                 dev_err(&pdev->dev, "cannot request HS-I2C IRQ %d\n", i2c->irq);
 794                 goto err_clk;
 795         }
 796
 797         i2c->variant = of_device_get_match_data(&pdev->dev);
 798
 799         ret = exynos5_hsi2c_clock_setup(i2c);
 800         if (ret)
 801                 goto err_clk;
 802
 803         exynos5_i2c_reset(i2c);
 804
 805         ret = i2c_add_adapter(&i2c->adap);
 806         if (ret < 0)
 807                 goto err_clk;
 808
 809         platform_set_drvdata(pdev, i2c);
 810
 811         clk_disable(i2c->clk);
 812
 813         return 0;
 814
 815  err_clk:
 816         clk_disable_unprepare(i2c->clk);
 817         return ret;
 818 }
 819
 820 static int exynos5_i2c_remove(struct platform_device *pdev)
 821 {
 822         struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
 823
 824         i2c_del_adapter(&i2c->adap);
 825
 826         clk_unprepare(i2c->clk);
 827
 828         return 0;
 829 }
 830
 831 #ifdef CONFIG_PM_SLEEP
 832 static int exynos5_i2c_suspend_noirq(struct device *dev)
 833 {
 834         struct exynos5_i2c *i2c = dev_get_drvdata(dev);
 835
 836         i2c_mark_adapter_suspended(&i2c->adap);
 837         clk_unprepare(i2c->clk);
 838
 839         return 0;
 840 }
 841
 842 static int exynos5_i2c_resume_noirq(struct device *dev)
 843 {
 844         struct exynos5_i2c *i2c = dev_get_drvdata(dev);
 845         int ret = 0;
 846
 847         ret = clk_prepare_enable(i2c->clk);
 848         if (ret)
 849                 return ret;
 850
 851         ret = exynos5_hsi2c_clock_setup(i2c);
 852         if (ret) {
 853                 clk_disable_unprepare(i2c->clk);
 854                 return ret;
 855         }
 856
 857         exynos5_i2c_init(i2c);
 858         clk_disable(i2c->clk);
 859         i2c_mark_adapter_resumed(&i2c->adap);
 860
 861         return 0;
 862 }
 863 #endif
 864
 865 static const struct dev_pm_ops exynos5_i2c_dev_pm_ops = {
 866         SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(exynos5_i2c_suspend_noirq,
 867                                       exynos5_i2c_resume_noirq)
 868 };
 869
 870 static struct platform_driver exynos5_i2c_driver = {
 871         .probe          = exynos5_i2c_probe,
 872         .remove         = exynos5_i2c_remove,
 873         .driver         = {
 874                 .name   = "exynos5-hsi2c",
 875                 .pm     = &exynos5_i2c_dev_pm_ops,
 876                 .of_match_table = exynos5_i2c_match,
 877         },
 878 };
 879
 880 module_platform_driver(exynos5_i2c_driver);
 881
 882 MODULE_DESCRIPTION("Exynos5 HS-I2C Bus driver");
 883 MODULE_AUTHOR("Naveen Krishna Chatradhi <ch.naveen@samsung.com>");
 884 MODULE_AUTHOR("Taekgyun Ko <taeggyun.ko@samsung.com>");
 885 MODULE_LICENSE("GPL v2");