drivers/hwmon/pmbus/ucd9000.c

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  * Hardware monitoring driver for UCD90xxx Sequencer and System Health
   4  * Controller series
   5  *
   6  * Copyright (C) 2011 Ericsson AB.
   7  */
   8
   9 #include <linux/debugfs.h>
  10 #include <linux/kernel.h>
  11 #include <linux/module.h>
  12 #include <linux/of_device.h>
  13 #include <linux/init.h>
  14 #include <linux/err.h>
  15 #include <linux/slab.h>
  16 #include <linux/i2c.h>
  17 #include <linux/pmbus.h>
  18 #include <linux/gpio/driver.h>
  19 #include "pmbus.h"
  20
  21 enum chips { ucd9000, ucd90120, ucd90124, ucd90160, ucd90320, ucd9090,
  22              ucd90910 };
  23
  24 #define UCD9000_MONITOR_CONFIG          0xd5
  25 #define UCD9000_NUM_PAGES               0xd6
  26 #define UCD9000_FAN_CONFIG_INDEX        0xe7
  27 #define UCD9000_FAN_CONFIG              0xe8
  28 #define UCD9000_MFR_STATUS              0xf3
  29 #define UCD9000_GPIO_SELECT             0xfa
  30 #define UCD9000_GPIO_CONFIG             0xfb
  31 #define UCD9000_DEVICE_ID               0xfd
  32
  33 /* GPIO CONFIG bits */
  34 #define UCD9000_GPIO_CONFIG_ENABLE      BIT(0)
  35 #define UCD9000_GPIO_CONFIG_OUT_ENABLE  BIT(1)
  36 #define UCD9000_GPIO_CONFIG_OUT_VALUE   BIT(2)
  37 #define UCD9000_GPIO_CONFIG_STATUS      BIT(3)
  38 #define UCD9000_GPIO_INPUT              0
  39 #define UCD9000_GPIO_OUTPUT             1
  40
  41 #define UCD9000_MON_TYPE(x)     (((x) >> 5) & 0x07)
  42 #define UCD9000_MON_PAGE(x)     ((x) & 0x1f)
  43
  44 #define UCD9000_MON_VOLTAGE     1
  45 #define UCD9000_MON_TEMPERATURE 2
  46 #define UCD9000_MON_CURRENT     3
  47 #define UCD9000_MON_VOLTAGE_HW  4
  48
  49 #define UCD9000_NUM_FAN         4
  50
  51 #define UCD9000_GPIO_NAME_LEN   16
  52 #define UCD9090_NUM_GPIOS       23
  53 #define UCD901XX_NUM_GPIOS      26
  54 #define UCD90320_NUM_GPIOS      84
  55 #define UCD90910_NUM_GPIOS      26
  56
  57 #define UCD9000_DEBUGFS_NAME_LEN        24
  58 #define UCD9000_GPI_COUNT               8
  59 #define UCD90320_GPI_COUNT              32
  60
  61 struct ucd9000_data {
  62         u8 fan_data[UCD9000_NUM_FAN][I2C_SMBUS_BLOCK_MAX];
  63         struct pmbus_driver_info info;
  64 #ifdef CONFIG_GPIOLIB
  65         struct gpio_chip gpio;
  66 #endif
  67         struct dentry *debugfs;
  68 };
  69 #define to_ucd9000_data(_info) container_of(_info, struct ucd9000_data, info)
  70
  71 struct ucd9000_debugfs_entry {
  72         struct i2c_client *client;
  73         u8 index;
  74 };
  75
  76 static int ucd9000_get_fan_config(struct i2c_client *client, int fan)
  77 {
  78         int fan_config = 0;
  79         struct ucd9000_data *data
  80           = to_ucd9000_data(pmbus_get_driver_info(client));
  81
  82         if (data->fan_data[fan][3] & 1)
  83                 fan_config |= PB_FAN_2_INSTALLED;   /* Use lower bit position */
  84
  85         /* Pulses/revolution */
  86         fan_config |= (data->fan_data[fan][3] & 0x06) >> 1;
  87
  88         return fan_config;
  89 }
  90
  91 static int ucd9000_read_byte_data(struct i2c_client *client, int page, int reg)
  92 {
  93         int ret = 0;
  94         int fan_config;
  95
  96         switch (reg) {
  97         case PMBUS_FAN_CONFIG_12:
  98                 if (page > 0)
  99                         return -ENXIO;
 100
 101                 ret = ucd9000_get_fan_config(client, 0);
 102                 if (ret < 0)
 103                         return ret;
 104                 fan_config = ret << 4;
 105                 ret = ucd9000_get_fan_config(client, 1);
 106                 if (ret < 0)
 107                         return ret;
 108                 fan_config |= ret;
 109                 ret = fan_config;
 110                 break;
 111         case PMBUS_FAN_CONFIG_34:
 112                 if (page > 0)
 113                         return -ENXIO;
 114
 115                 ret = ucd9000_get_fan_config(client, 2);
 116                 if (ret < 0)
 117                         return ret;
 118                 fan_config = ret << 4;
 119                 ret = ucd9000_get_fan_config(client, 3);
 120                 if (ret < 0)
 121                         return ret;
 122                 fan_config |= ret;
 123                 ret = fan_config;
 124                 break;
 125         default:
 126                 ret = -ENODATA;
 127                 break;
 128         }
 129         return ret;
 130 }
 131
 132 static const struct i2c_device_id ucd9000_id[] = {
 133         {"ucd9000", ucd9000},
 134         {"ucd90120", ucd90120},
 135         {"ucd90124", ucd90124},
 136         {"ucd90160", ucd90160},
 137         {"ucd90320", ucd90320},
 138         {"ucd9090", ucd9090},
 139         {"ucd90910", ucd90910},
 140         {}
 141 };
 142 MODULE_DEVICE_TABLE(i2c, ucd9000_id);
 143
 144 static const struct of_device_id __maybe_unused ucd9000_of_match[] = {
 145         {
 146                 .compatible = "ti,ucd9000",
 147                 .data = (void *)ucd9000
 148         },
 149         {
 150                 .compatible = "ti,ucd90120",
 151                 .data = (void *)ucd90120
 152         },
 153         {
 154                 .compatible = "ti,ucd90124",
 155                 .data = (void *)ucd90124
 156         },
 157         {
 158                 .compatible = "ti,ucd90160",
 159                 .data = (void *)ucd90160
 160         },
 161         {
 162                 .compatible = "ti,ucd90320",
 163                 .data = (void *)ucd90320
 164         },
 165         {
 166                 .compatible = "ti,ucd9090",
 167                 .data = (void *)ucd9090
 168         },
 169         {
 170                 .compatible = "ti,ucd90910",
 171                 .data = (void *)ucd90910
 172         },
 173         { },
 174 };
 175 MODULE_DEVICE_TABLE(of, ucd9000_of_match);
 176
 177 #ifdef CONFIG_GPIOLIB
 178 static int ucd9000_gpio_read_config(struct i2c_client *client,
 179                                     unsigned int offset)
 180 {
 181         int ret;
 182
 183         /* No page set required */
 184         ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_SELECT, offset);
 185         if (ret < 0)
 186                 return ret;
 187
 188         return i2c_smbus_read_byte_data(client, UCD9000_GPIO_CONFIG);
 189 }
 190
 191 static int ucd9000_gpio_get(struct gpio_chip *gc, unsigned int offset)
 192 {
 193         struct i2c_client *client  = gpiochip_get_data(gc);
 194         int ret;
 195
 196         ret = ucd9000_gpio_read_config(client, offset);
 197         if (ret < 0)
 198                 return ret;
 199
 200         return !!(ret & UCD9000_GPIO_CONFIG_STATUS);
 201 }
 202
 203 static void ucd9000_gpio_set(struct gpio_chip *gc, unsigned int offset,
 204                              int value)
 205 {
 206         struct i2c_client *client = gpiochip_get_data(gc);
 207         int ret;
 208
 209         ret = ucd9000_gpio_read_config(client, offset);
 210         if (ret < 0) {
 211                 dev_dbg(&client->dev, "failed to read GPIO %d config: %d\n",
 212                         offset, ret);
 213                 return;
 214         }
 215
 216         if (value) {
 217                 if (ret & UCD9000_GPIO_CONFIG_STATUS)
 218                         return;
 219
 220                 ret |= UCD9000_GPIO_CONFIG_STATUS;
 221         } else {
 222                 if (!(ret & UCD9000_GPIO_CONFIG_STATUS))
 223                         return;
 224
 225                 ret &= ~UCD9000_GPIO_CONFIG_STATUS;
 226         }
 227
 228         ret |= UCD9000_GPIO_CONFIG_ENABLE;
 229
 230         /* Page set not required */
 231         ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, ret);
 232         if (ret < 0) {
 233                 dev_dbg(&client->dev, "Failed to write GPIO %d config: %d\n",
 234                         offset, ret);
 235                 return;
 236         }
 237
 238         ret &= ~UCD9000_GPIO_CONFIG_ENABLE;
 239
 240         ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, ret);
 241         if (ret < 0)
 242                 dev_dbg(&client->dev, "Failed to write GPIO %d config: %d\n",
 243                         offset, ret);
 244 }
 245
 246 static int ucd9000_gpio_get_direction(struct gpio_chip *gc,
 247                                       unsigned int offset)
 248 {
 249         struct i2c_client *client = gpiochip_get_data(gc);
 250         int ret;
 251
 252         ret = ucd9000_gpio_read_config(client, offset);
 253         if (ret < 0)
 254                 return ret;
 255
 256         return !(ret & UCD9000_GPIO_CONFIG_OUT_ENABLE);
 257 }
 258
 259 static int ucd9000_gpio_set_direction(struct gpio_chip *gc,
 260                                       unsigned int offset, bool direction_out,
 261                                       int requested_out)
 262 {
 263         struct i2c_client *client = gpiochip_get_data(gc);
 264         int ret, config, out_val;
 265
 266         ret = ucd9000_gpio_read_config(client, offset);
 267         if (ret < 0)
 268                 return ret;
 269
 270         if (direction_out) {
 271                 out_val = requested_out ? UCD9000_GPIO_CONFIG_OUT_VALUE : 0;
 272
 273                 if (ret & UCD9000_GPIO_CONFIG_OUT_ENABLE) {
 274                         if ((ret & UCD9000_GPIO_CONFIG_OUT_VALUE) == out_val)
 275                                 return 0;
 276                 } else {
 277                         ret |= UCD9000_GPIO_CONFIG_OUT_ENABLE;
 278                 }
 279
 280                 if (out_val)
 281                         ret |= UCD9000_GPIO_CONFIG_OUT_VALUE;
 282                 else
 283                         ret &= ~UCD9000_GPIO_CONFIG_OUT_VALUE;
 284
 285         } else {
 286                 if (!(ret & UCD9000_GPIO_CONFIG_OUT_ENABLE))
 287                         return 0;
 288
 289                 ret &= ~UCD9000_GPIO_CONFIG_OUT_ENABLE;
 290         }
 291
 292         ret |= UCD9000_GPIO_CONFIG_ENABLE;
 293         config = ret;
 294
 295         /* Page set not required */
 296         ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, config);
 297         if (ret < 0)
 298                 return ret;
 299
 300         config &= ~UCD9000_GPIO_CONFIG_ENABLE;
 301
 302         return i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, config);
 303 }
 304
 305 static int ucd9000_gpio_direction_input(struct gpio_chip *gc,
 306                                         unsigned int offset)
 307 {
 308         return ucd9000_gpio_set_direction(gc, offset, UCD9000_GPIO_INPUT, 0);
 309 }
 310
 311 static int ucd9000_gpio_direction_output(struct gpio_chip *gc,
 312                                          unsigned int offset, int val)
 313 {
 314         return ucd9000_gpio_set_direction(gc, offset, UCD9000_GPIO_OUTPUT,
 315                                           val);
 316 }
 317
 318 static void ucd9000_probe_gpio(struct i2c_client *client,
 319                                const struct i2c_device_id *mid,
 320                                struct ucd9000_data *data)
 321 {
 322         int rc;
 323
 324         switch (mid->driver_data) {
 325         case ucd9090:
 326                 data->gpio.ngpio = UCD9090_NUM_GPIOS;
 327                 break;
 328         case ucd90120:
 329         case ucd90124:
 330         case ucd90160:
 331                 data->gpio.ngpio = UCD901XX_NUM_GPIOS;
 332                 break;
 333         case ucd90320:
 334                 data->gpio.ngpio = UCD90320_NUM_GPIOS;
 335                 break;
 336         case ucd90910:
 337                 data->gpio.ngpio = UCD90910_NUM_GPIOS;
 338                 break;
 339         default:
 340                 return; /* GPIO support is optional. */
 341         }
 342
 343         /*
 344          * Pinmux support has not been added to the new gpio_chip.
 345          * This support should be added when possible given the mux
 346          * behavior of these IO devices.
 347          */
 348         data->gpio.label = client->name;
 349         data->gpio.get_direction = ucd9000_gpio_get_direction;
 350         data->gpio.direction_input = ucd9000_gpio_direction_input;
 351         data->gpio.direction_output = ucd9000_gpio_direction_output;
 352         data->gpio.get = ucd9000_gpio_get;
 353         data->gpio.set = ucd9000_gpio_set;
 354         data->gpio.can_sleep = true;
 355         data->gpio.base = -1;
 356         data->gpio.parent = &client->dev;
 357
 358         rc = devm_gpiochip_add_data(&client->dev, &data->gpio, client);
 359         if (rc)
 360                 dev_warn(&client->dev, "Could not add gpiochip: %d\n", rc);
 361 }
 362 #else
 363 static void ucd9000_probe_gpio(struct i2c_client *client,
 364                                const struct i2c_device_id *mid,
 365                                struct ucd9000_data *data)
 366 {
 367 }
 368 #endif /* CONFIG_GPIOLIB */
 369
 370 #ifdef CONFIG_DEBUG_FS
 371 static int ucd9000_get_mfr_status(struct i2c_client *client, u8 *buffer)
 372 {
 373         int ret = pmbus_set_page(client, 0);
 374
 375         if (ret < 0)
 376                 return ret;
 377
 378         return i2c_smbus_read_block_data(client, UCD9000_MFR_STATUS, buffer);
 379 }
 380
 381 static int ucd9000_debugfs_show_mfr_status_bit(void *data, u64 *val)
 382 {
 383         struct ucd9000_debugfs_entry *entry = data;
 384         struct i2c_client *client = entry->client;
 385         u8 buffer[I2C_SMBUS_BLOCK_MAX];
 386         int ret, i;
 387
 388         ret = ucd9000_get_mfr_status(client, buffer);
 389         if (ret < 0)
 390                 return ret;
 391
 392         /*
 393          * GPI fault bits are in sets of 8, two bytes from end of response.
 394          */
 395         i = ret - 3 - entry->index / 8;
 396         if (i >= 0)
 397                 *val = !!(buffer[i] & BIT(entry->index % 8));
 398
 399         return 0;
 400 }
 401 DEFINE_DEBUGFS_ATTRIBUTE(ucd9000_debugfs_mfr_status_bit,
 402                          ucd9000_debugfs_show_mfr_status_bit, NULL, "%1lld\n");
 403
 404 static ssize_t ucd9000_debugfs_read_mfr_status(struct file *file,
 405                                                char __user *buf, size_t count,
 406                                                loff_t *ppos)
 407 {
 408         struct i2c_client *client = file->private_data;
 409         u8 buffer[I2C_SMBUS_BLOCK_MAX];
 410         char str[(I2C_SMBUS_BLOCK_MAX * 2) + 2];
 411         char *res;
 412         int rc;
 413
 414         rc = ucd9000_get_mfr_status(client, buffer);
 415         if (rc < 0)
 416                 return rc;
 417
 418         res = bin2hex(str, buffer, min(rc, I2C_SMBUS_BLOCK_MAX));
 419         *res++ = '\n';
 420         *res = 0;
 421
 422         return simple_read_from_buffer(buf, count, ppos, str, res - str);
 423 }
 424
 425 static const struct file_operations ucd9000_debugfs_show_mfr_status_fops = {
 426         .llseek = noop_llseek,
 427         .read = ucd9000_debugfs_read_mfr_status,
 428         .open = simple_open,
 429 };
 430
 431 static int ucd9000_init_debugfs(struct i2c_client *client,
 432                                 const struct i2c_device_id *mid,
 433                                 struct ucd9000_data *data)
 434 {
 435         struct dentry *debugfs;
 436         struct ucd9000_debugfs_entry *entries;
 437         int i, gpi_count;
 438         char name[UCD9000_DEBUGFS_NAME_LEN];
 439
 440         debugfs = pmbus_get_debugfs_dir(client);
 441         if (!debugfs)
 442                 return -ENOENT;
 443
 444         data->debugfs = debugfs_create_dir(client->name, debugfs);
 445         if (!data->debugfs)
 446                 return -ENOENT;
 447
 448         /*
 449          * Of the chips this driver supports, only the UCD9090, UCD90160,
 450          * UCD90320, and UCD90910 report GPI faults in their MFR_STATUS
 451          * register, so only create the GPI fault debugfs attributes for those
 452          * chips.
 453          */
 454         if (mid->driver_data == ucd9090 || mid->driver_data == ucd90160 ||
 455             mid->driver_data == ucd90320 || mid->driver_data == ucd90910) {
 456                 gpi_count = mid->driver_data == ucd90320 ? UCD90320_GPI_COUNT
 457                                                          : UCD9000_GPI_COUNT;
 458                 entries = devm_kcalloc(&client->dev,
 459                                        gpi_count, sizeof(*entries),
 460                                        GFP_KERNEL);
 461                 if (!entries)
 462                         return -ENOMEM;
 463
 464                 for (i = 0; i < gpi_count; i++) {
 465                         entries[i].client = client;
 466                         entries[i].index = i;
 467                         scnprintf(name, UCD9000_DEBUGFS_NAME_LEN,
 468                                   "gpi%d_alarm", i + 1);
 469                         debugfs_create_file(name, 0444, data->debugfs,
 470                                             &entries[i],
 471                                             &ucd9000_debugfs_mfr_status_bit);
 472                 }
 473         }
 474
 475         scnprintf(name, UCD9000_DEBUGFS_NAME_LEN, "mfr_status");
 476         debugfs_create_file(name, 0444, data->debugfs, client,
 477                             &ucd9000_debugfs_show_mfr_status_fops);
 478
 479         return 0;
 480 }
 481 #else
 482 static int ucd9000_init_debugfs(struct i2c_client *client,
 483                                 const struct i2c_device_id *mid,
 484                                 struct ucd9000_data *data)
 485 {
 486         return 0;
 487 }
 488 #endif /* CONFIG_DEBUG_FS */
 489
 490 static int ucd9000_probe(struct i2c_client *client,
 491                          const struct i2c_device_id *id)
 492 {
 493         u8 block_buffer[I2C_SMBUS_BLOCK_MAX + 1];
 494         struct ucd9000_data *data;
 495         struct pmbus_driver_info *info;
 496         const struct i2c_device_id *mid;
 497         enum chips chip;
 498         int i, ret;
 499
 500         if (!i2c_check_functionality(client->adapter,
 501                                      I2C_FUNC_SMBUS_BYTE_DATA |
 502                                      I2C_FUNC_SMBUS_BLOCK_DATA))
 503                 return -ENODEV;
 504
 505         ret = i2c_smbus_read_block_data(client, UCD9000_DEVICE_ID,
 506                                         block_buffer);
 507         if (ret < 0) {
 508                 dev_err(&client->dev, "Failed to read device ID\n");
 509                 return ret;
 510         }
 511         block_buffer[ret] = '\0';
 512         dev_info(&client->dev, "Device ID %s\n", block_buffer);
 513
 514         for (mid = ucd9000_id; mid->name[0]; mid++) {
 515                 if (!strncasecmp(mid->name, block_buffer, strlen(mid->name)))
 516                         break;
 517         }
 518         if (!mid->name[0]) {
 519                 dev_err(&client->dev, "Unsupported device\n");
 520                 return -ENODEV;
 521         }
 522
 523         if (client->dev.of_node)
 524                 chip = (enum chips)of_device_get_match_data(&client->dev);
 525         else
 526                 chip = id->driver_data;
 527
 528         if (chip != ucd9000 && chip != mid->driver_data)
 529                 dev_notice(&client->dev,
 530                            "Device mismatch: Configured %s, detected %s\n",
 531                            id->name, mid->name);
 532
 533         data = devm_kzalloc(&client->dev, sizeof(struct ucd9000_data),
 534                             GFP_KERNEL);
 535         if (!data)
 536                 return -ENOMEM;
 537         info = &data->info;
 538
 539         ret = i2c_smbus_read_byte_data(client, UCD9000_NUM_PAGES);
 540         if (ret < 0) {
 541                 dev_err(&client->dev,
 542                         "Failed to read number of active pages\n");
 543                 return ret;
 544         }
 545         info->pages = ret;
 546         if (!info->pages) {
 547                 dev_err(&client->dev, "No pages configured\n");
 548                 return -ENODEV;
 549         }
 550
 551         /* The internal temperature sensor is always active */
 552         info->func[0] = PMBUS_HAVE_TEMP;
 553
 554         /* Everything else is configurable */
 555         ret = i2c_smbus_read_block_data(client, UCD9000_MONITOR_CONFIG,
 556                                         block_buffer);
 557         if (ret <= 0) {
 558                 dev_err(&client->dev, "Failed to read configuration data\n");
 559                 return -ENODEV;
 560         }
 561         for (i = 0; i < ret; i++) {
 562                 int page = UCD9000_MON_PAGE(block_buffer[i]);
 563
 564                 if (page >= info->pages)
 565                         continue;
 566
 567                 switch (UCD9000_MON_TYPE(block_buffer[i])) {
 568                 case UCD9000_MON_VOLTAGE:
 569                 case UCD9000_MON_VOLTAGE_HW:
 570                         info->func[page] |= PMBUS_HAVE_VOUT
 571                           | PMBUS_HAVE_STATUS_VOUT;
 572                         break;
 573                 case UCD9000_MON_TEMPERATURE:
 574                         info->func[page] |= PMBUS_HAVE_TEMP2
 575                           | PMBUS_HAVE_STATUS_TEMP;
 576                         break;
 577                 case UCD9000_MON_CURRENT:
 578                         info->func[page] |= PMBUS_HAVE_IOUT
 579                           | PMBUS_HAVE_STATUS_IOUT;
 580                         break;
 581                 default:
 582                         break;
 583                 }
 584         }
 585
 586         /* Fan configuration */
 587         if (mid->driver_data == ucd90124) {
 588                 for (i = 0; i < UCD9000_NUM_FAN; i++) {
 589                         i2c_smbus_write_byte_data(client,
 590                                                   UCD9000_FAN_CONFIG_INDEX, i);
 591                         ret = i2c_smbus_read_block_data(client,
 592                                                         UCD9000_FAN_CONFIG,
 593                                                         data->fan_data[i]);
 594                         if (ret < 0)
 595                                 return ret;
 596                 }
 597                 i2c_smbus_write_byte_data(client, UCD9000_FAN_CONFIG_INDEX, 0);
 598
 599                 info->read_byte_data = ucd9000_read_byte_data;
 600                 info->func[0] |= PMBUS_HAVE_FAN12 | PMBUS_HAVE_STATUS_FAN12
 601                   | PMBUS_HAVE_FAN34 | PMBUS_HAVE_STATUS_FAN34;
 602         }
 603
 604         ucd9000_probe_gpio(client, mid, data);
 605
 606         ret = pmbus_do_probe(client, mid, info);
 607         if (ret)
 608                 return ret;
 609
 610         ret = ucd9000_init_debugfs(client, mid, data);
 611         if (ret)
 612                 dev_warn(&client->dev, "Failed to register debugfs: %d\n",
 613                          ret);
 614
 615         return 0;
 616 }
 617
 618 /* This is the driver that will be inserted */
 619 static struct i2c_driver ucd9000_driver = {
 620         .driver = {
 621                 .name = "ucd9000",
 622                 .of_match_table = of_match_ptr(ucd9000_of_match),
 623         },
 624         .probe = ucd9000_probe,
 625         .remove = pmbus_do_remove,
 626         .id_table = ucd9000_id,
 627 };
 628
 629 module_i2c_driver(ucd9000_driver);
 630
 631 MODULE_AUTHOR("Guenter Roeck");
 632 MODULE_DESCRIPTION("PMBus driver for TI UCD90xxx");
 633 MODULE_LICENSE("GPL");