1 // SPDX-License-Identifier: GPL-2.0+
3 * rcar_du_group.c -- R-Car Display Unit Channels Pair
5 * Copyright (C) 2013-2015 Renesas Electronics Corporation
7 * Contact: Laurent Pinchart (laurent.pinchart@ideasonboard.com)
11 * The R8A7779 DU is split in per-CRTC resources (scan-out engine, blending
12 * unit, timings generator, ...) and device-global resources (start/stop
13 * control, planes, ...) shared between the two CRTCs.
15 * The R8A7790 introduced a third CRTC with its own set of global resources.
16 * This would be modeled as two separate DU device instances if it wasn't for
17 * a handful or resources that are shared between the three CRTCs (mostly
18 * related to input and output routing). For this reason the R8A7790 DU must be
19 * modeled as a single device with three CRTCs, two sets of "semi-global"
20 * resources, and a few device-global resources.
22 * The rcar_du_group object is a driver specific object, without any real
23 * counterpart in the DU documentation, that models those semi-global resources.
26 #include <linux/clk.h>
29 #include "rcar_du_drv.h"
30 #include "rcar_du_group.h"
31 #include "rcar_du_regs.h"
33 u32 rcar_du_group_read(struct rcar_du_group *rgrp, u32 reg)
35 return rcar_du_read(rgrp->dev, rgrp->mmio_offset + reg);
38 void rcar_du_group_write(struct rcar_du_group *rgrp, u32 reg, u32 data)
40 rcar_du_write(rgrp->dev, rgrp->mmio_offset + reg, data);
43 static void rcar_du_group_setup_pins(struct rcar_du_group *rgrp)
45 u32 defr6 = DEFR6_CODE;
47 if (rgrp->channels_mask & BIT(0))
48 defr6 |= DEFR6_ODPM02_DISP;
50 if (rgrp->channels_mask & BIT(1))
51 defr6 |= DEFR6_ODPM12_DISP;
53 rcar_du_group_write(rgrp, DEFR6, defr6);
56 static void rcar_du_group_setup_defr8(struct rcar_du_group *rgrp)
58 struct rcar_du_device *rcdu = rgrp->dev;
59 u32 defr8 = DEFR8_CODE;
61 if (rcdu->info->gen < 3) {
65 * On Gen2 the DEFR8 register for the first group also controls
66 * RGB output routing to DPAD0 and VSPD1 routing to DU0/1/2 for
67 * DU instances that support it.
69 if (rgrp->index == 0) {
70 defr8 |= DEFR8_DRGBS_DU(rcdu->dpad0_source);
71 if (rgrp->dev->vspd1_sink == 2)
76 * On Gen3 VSPD routing can't be configured, and DPAD routing
77 * is set in the group corresponding to the DPAD output (no Gen3
78 * SoC has multiple DPAD sources belonging to separate groups).
80 if (rgrp->index == rcdu->dpad0_source / 2)
81 defr8 |= DEFR8_DRGBS_DU(rcdu->dpad0_source);
84 rcar_du_group_write(rgrp, DEFR8, defr8);
87 static void rcar_du_group_setup_didsr(struct rcar_du_group *rgrp)
89 struct rcar_du_device *rcdu = rgrp->dev;
90 struct rcar_du_crtc *rcrtc;
91 unsigned int num_crtcs = 0;
96 * Configure input dot clock routing with a hardcoded configuration. If
97 * the DU channel can use the LVDS encoder output clock as the dot
98 * clock, do so. Otherwise route DU_DOTCLKINn signal to DUn.
100 * Each channel can then select between the dot clock configured here
101 * and the clock provided by the CPG through the ESCR register.
103 if (rcdu->info->gen < 3 && rgrp->index == 0) {
105 * On Gen2 a single register in the first group controls dot
106 * clock selection for all channels.
109 num_crtcs = rcdu->num_crtcs;
110 } else if (rcdu->info->gen == 3 && rgrp->num_crtcs > 1) {
112 * On Gen3 dot clocks are setup through per-group registers,
113 * only available when the group has two channels.
115 rcrtc = &rcdu->crtcs[rgrp->index * 2];
116 num_crtcs = rgrp->num_crtcs;
123 for (i = 0; i < num_crtcs; ++i, ++rcrtc) {
124 if (rcdu->info->lvds_clk_mask & BIT(rcrtc->index))
125 didsr |= DIDSR_LCDS_LVDS0(i)
126 | DIDSR_PDCS_CLK(i, 0);
128 didsr |= DIDSR_LCDS_DCLKIN(i)
129 | DIDSR_PDCS_CLK(i, 0);
132 rcar_du_group_write(rgrp, DIDSR, didsr);
135 static void rcar_du_group_setup(struct rcar_du_group *rgrp)
137 struct rcar_du_device *rcdu = rgrp->dev;
138 u32 defr7 = DEFR7_CODE;
140 /* Enable extended features */
141 rcar_du_group_write(rgrp, DEFR, DEFR_CODE | DEFR_DEFE);
142 if (rcdu->info->gen < 3) {
143 rcar_du_group_write(rgrp, DEFR2, DEFR2_CODE | DEFR2_DEFE2G);
144 rcar_du_group_write(rgrp, DEFR3, DEFR3_CODE | DEFR3_DEFE3);
145 rcar_du_group_write(rgrp, DEFR4, DEFR4_CODE);
147 rcar_du_group_write(rgrp, DEFR5, DEFR5_CODE | DEFR5_DEFE5);
149 rcar_du_group_setup_pins(rgrp);
152 * TODO: Handle routing of the DU output to CMM dynamically, as we
153 * should bypass CMM completely when no color management feature is
156 defr7 |= (rgrp->cmms_mask & BIT(1) ? DEFR7_CMME1 : 0) |
157 (rgrp->cmms_mask & BIT(0) ? DEFR7_CMME0 : 0);
158 rcar_du_group_write(rgrp, DEFR7, defr7);
160 if (rcdu->info->gen >= 2) {
161 rcar_du_group_setup_defr8(rgrp);
162 rcar_du_group_setup_didsr(rgrp);
165 if (rcdu->info->gen >= 3)
166 rcar_du_group_write(rgrp, DEFR10, DEFR10_CODE | DEFR10_DEFE10);
169 * Use DS1PR and DS2PR to configure planes priorities and connects the
170 * superposition 0 to DU0 pins. DU1 pins will be configured dynamically.
172 rcar_du_group_write(rgrp, DORCR, DORCR_PG1D_DS1 | DORCR_DPRS);
174 /* Apply planes to CRTCs association. */
175 mutex_lock(&rgrp->lock);
176 rcar_du_group_write(rgrp, DPTSR, (rgrp->dptsr_planes << 16) |
178 mutex_unlock(&rgrp->lock);
182 * rcar_du_group_get - Acquire a reference to the DU channels group
184 * Acquiring the first reference setups core registers. A reference must be held
185 * before accessing any hardware registers.
187 * This function must be called with the DRM mode_config lock held.
189 * Return 0 in case of success or a negative error code otherwise.
191 int rcar_du_group_get(struct rcar_du_group *rgrp)
196 rcar_du_group_setup(rgrp);
204 * rcar_du_group_put - Release a reference to the DU
206 * This function must be called with the DRM mode_config lock held.
208 void rcar_du_group_put(struct rcar_du_group *rgrp)
213 static void __rcar_du_group_start_stop(struct rcar_du_group *rgrp, bool start)
215 struct rcar_du_device *rcdu = rgrp->dev;
218 * Group start/stop is controlled by the DRES and DEN bits of DSYSR0
219 * for the first group and DSYSR2 for the second group. On most DU
220 * instances, this maps to the first CRTC of the group, and we can just
221 * use rcar_du_crtc_dsysr_clr_set() to access the correct DSYSR. On
222 * M3-N, however, DU2 doesn't exist, but DSYSR2 does. We thus need to
223 * access the register directly using group read/write.
225 if (rcdu->info->channels_mask & BIT(rgrp->index * 2)) {
226 struct rcar_du_crtc *rcrtc = &rgrp->dev->crtcs[rgrp->index * 2];
228 rcar_du_crtc_dsysr_clr_set(rcrtc, DSYSR_DRES | DSYSR_DEN,
229 start ? DSYSR_DEN : DSYSR_DRES);
231 rcar_du_group_write(rgrp, DSYSR,
232 start ? DSYSR_DEN : DSYSR_DRES);
236 void rcar_du_group_start_stop(struct rcar_du_group *rgrp, bool start)
239 * Many of the configuration bits are only updated when the display
240 * reset (DRES) bit in DSYSR is set to 1, disabling *both* CRTCs. Some
241 * of those bits could be pre-configured, but others (especially the
242 * bits related to plane assignment to display timing controllers) need
243 * to be modified at runtime.
245 * Restart the display controller if a start is requested. Sorry for the
246 * flicker. It should be possible to move most of the "DRES-update" bits
247 * setup to driver initialization time and minimize the number of cases
248 * when the display controller will have to be restarted.
251 if (rgrp->used_crtcs++ != 0)
252 __rcar_du_group_start_stop(rgrp, false);
253 __rcar_du_group_start_stop(rgrp, true);
255 if (--rgrp->used_crtcs == 0)
256 __rcar_du_group_start_stop(rgrp, false);
260 void rcar_du_group_restart(struct rcar_du_group *rgrp)
262 rgrp->need_restart = false;
264 __rcar_du_group_start_stop(rgrp, false);
265 __rcar_du_group_start_stop(rgrp, true);
268 int rcar_du_set_dpad0_vsp1_routing(struct rcar_du_device *rcdu)
270 struct rcar_du_group *rgrp;
271 struct rcar_du_crtc *crtc;
275 if (rcdu->info->gen < 2)
279 * RGB output routing to DPAD0 and VSP1D routing to DU0/1/2 are
280 * configured in the DEFR8 register of the first group on Gen2 and the
281 * last group on Gen3. As this function can be called with the DU
282 * channels of the corresponding CRTCs disabled, we need to enable the
283 * group clock before accessing the register.
285 index = rcdu->info->gen < 3 ? 0 : DIV_ROUND_UP(rcdu->num_crtcs, 2) - 1;
286 rgrp = &rcdu->groups[index];
287 crtc = &rcdu->crtcs[index * 2];
289 ret = clk_prepare_enable(crtc->clock);
293 rcar_du_group_setup_defr8(rgrp);
295 clk_disable_unprepare(crtc->clock);
300 static void rcar_du_group_set_dpad_levels(struct rcar_du_group *rgrp)
302 static const u32 doflr_values[2] = {
303 DOFLR_HSYCFL0 | DOFLR_VSYCFL0 | DOFLR_ODDFL0 |
304 DOFLR_DISPFL0 | DOFLR_CDEFL0 | DOFLR_RGBFL0,
305 DOFLR_HSYCFL1 | DOFLR_VSYCFL1 | DOFLR_ODDFL1 |
306 DOFLR_DISPFL1 | DOFLR_CDEFL1 | DOFLR_RGBFL1,
308 static const u32 dpad_mask = BIT(RCAR_DU_OUTPUT_DPAD1)
309 | BIT(RCAR_DU_OUTPUT_DPAD0);
310 struct rcar_du_device *rcdu = rgrp->dev;
311 u32 doflr = DOFLR_CODE;
314 if (rcdu->info->gen < 2)
318 * The DPAD outputs can't be controlled directly. However, the parallel
319 * output of the DU channels routed to DPAD can be set to fixed levels
320 * through the DOFLR group register. Use this to turn the DPAD on or off
321 * by driving fixed low-level signals at the output of any DU channel
322 * not routed to a DPAD output. This doesn't affect the DU output
323 * signals going to other outputs, such as the internal LVDS and HDMI
327 for (i = 0; i < rgrp->num_crtcs; ++i) {
328 struct rcar_du_crtc_state *rstate;
329 struct rcar_du_crtc *rcrtc;
331 rcrtc = &rcdu->crtcs[rgrp->index * 2 + i];
332 rstate = to_rcar_crtc_state(rcrtc->crtc.state);
334 if (!(rstate->outputs & dpad_mask))
335 doflr |= doflr_values[i];
338 rcar_du_group_write(rgrp, DOFLR, doflr);
341 int rcar_du_group_set_routing(struct rcar_du_group *rgrp)
343 struct rcar_du_device *rcdu = rgrp->dev;
344 u32 dorcr = rcar_du_group_read(rgrp, DORCR);
346 dorcr &= ~(DORCR_PG2T | DORCR_DK2S | DORCR_PG2D_MASK);
349 * Set the DPAD1 pins sources. Select CRTC 0 if explicitly requested and
350 * CRTC 1 in all other cases to avoid cloning CRTC 0 to DPAD0 and DPAD1
353 if (rcdu->dpad1_source == rgrp->index * 2)
354 dorcr |= DORCR_PG2D_DS1;
356 dorcr |= DORCR_PG2T | DORCR_DK2S | DORCR_PG2D_DS2;
358 rcar_du_group_write(rgrp, DORCR, dorcr);
360 rcar_du_group_set_dpad_levels(rgrp);
362 return rcar_du_set_dpad0_vsp1_routing(rgrp->dev);