1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * extcon-sm5502.c - Silicon Mitus SM5502 extcon drvier to support USB switches
5 * Copyright (c) 2014 Samsung Electronics Co., Ltd
6 * Author: Chanwoo Choi <cw00.choi@samsung.com>
10 #include <linux/i2c.h>
11 #include <linux/interrupt.h>
12 #include <linux/irqdomain.h>
13 #include <linux/kernel.h>
14 #include <linux/module.h>
15 #include <linux/platform_device.h>
16 #include <linux/regmap.h>
17 #include <linux/slab.h>
18 #include <linux/extcon-provider.h>
20 #include "extcon-sm5502.h"
22 #define DELAY_MS_DEFAULT 17000 /* unit: millisecond */
36 struct sm5502_muic_info {
38 struct extcon_dev *edev;
40 struct i2c_client *i2c;
41 struct regmap *regmap;
43 struct regmap_irq_chip_data *irq_data;
44 struct muic_irq *muic_irqs;
45 unsigned int num_muic_irqs;
49 struct work_struct irq_work;
51 struct reg_data *reg_data;
52 unsigned int num_reg_data;
57 * Use delayed workqueue to detect cable state and then
58 * notify cable state to notifiee/platform through uevent.
59 * After completing the booting of platform, the extcon provider
60 * driver should notify cable state to upper layer.
62 struct delayed_work wq_detcable;
65 /* Default value of SM5502 register to bring up MUIC device. */
66 static struct reg_data sm5502_reg_data[] = {
68 .reg = SM5502_REG_RESET,
69 .val = SM5502_REG_RESET_MASK,
72 .reg = SM5502_REG_CONTROL,
73 .val = SM5502_REG_CONTROL_MASK_INT_MASK,
76 .reg = SM5502_REG_INTMASK1,
77 .val = SM5502_REG_INTM1_KP_MASK
78 | SM5502_REG_INTM1_LKP_MASK
79 | SM5502_REG_INTM1_LKR_MASK,
82 .reg = SM5502_REG_INTMASK2,
83 .val = SM5502_REG_INTM2_VBUS_DET_MASK
84 | SM5502_REG_INTM2_REV_ACCE_MASK
85 | SM5502_REG_INTM2_ADC_CHG_MASK
86 | SM5502_REG_INTM2_STUCK_KEY_MASK
87 | SM5502_REG_INTM2_STUCK_KEY_RCV_MASK
88 | SM5502_REG_INTM2_MHL_MASK,
93 /* List of detectable cables */
94 static const unsigned int sm5502_extcon_cable[] = {
102 /* Define supported accessory type */
103 enum sm5502_muic_acc_type {
104 SM5502_MUIC_ADC_GROUND = 0x0,
105 SM5502_MUIC_ADC_SEND_END_BUTTON,
106 SM5502_MUIC_ADC_REMOTE_S1_BUTTON,
107 SM5502_MUIC_ADC_REMOTE_S2_BUTTON,
108 SM5502_MUIC_ADC_REMOTE_S3_BUTTON,
109 SM5502_MUIC_ADC_REMOTE_S4_BUTTON,
110 SM5502_MUIC_ADC_REMOTE_S5_BUTTON,
111 SM5502_MUIC_ADC_REMOTE_S6_BUTTON,
112 SM5502_MUIC_ADC_REMOTE_S7_BUTTON,
113 SM5502_MUIC_ADC_REMOTE_S8_BUTTON,
114 SM5502_MUIC_ADC_REMOTE_S9_BUTTON,
115 SM5502_MUIC_ADC_REMOTE_S10_BUTTON,
116 SM5502_MUIC_ADC_REMOTE_S11_BUTTON,
117 SM5502_MUIC_ADC_REMOTE_S12_BUTTON,
118 SM5502_MUIC_ADC_RESERVED_ACC_1,
119 SM5502_MUIC_ADC_RESERVED_ACC_2,
120 SM5502_MUIC_ADC_RESERVED_ACC_3,
121 SM5502_MUIC_ADC_RESERVED_ACC_4,
122 SM5502_MUIC_ADC_RESERVED_ACC_5,
123 SM5502_MUIC_ADC_AUDIO_TYPE2,
124 SM5502_MUIC_ADC_PHONE_POWERED_DEV,
125 SM5502_MUIC_ADC_TTY_CONVERTER,
126 SM5502_MUIC_ADC_UART_CABLE,
127 SM5502_MUIC_ADC_TYPE1_CHARGER,
128 SM5502_MUIC_ADC_FACTORY_MODE_BOOT_OFF_USB,
129 SM5502_MUIC_ADC_FACTORY_MODE_BOOT_ON_USB,
130 SM5502_MUIC_ADC_AUDIO_VIDEO_CABLE,
131 SM5502_MUIC_ADC_TYPE2_CHARGER,
132 SM5502_MUIC_ADC_FACTORY_MODE_BOOT_OFF_UART,
133 SM5502_MUIC_ADC_FACTORY_MODE_BOOT_ON_UART,
134 SM5502_MUIC_ADC_AUDIO_TYPE1,
135 SM5502_MUIC_ADC_OPEN = 0x1f,
138 * The below accessories have same ADC value (0x1f or 0x1e).
139 * So, Device type1 is used to separate specific accessory.
141 /* |---------|--ADC| */
143 SM5502_MUIC_ADC_AUDIO_TYPE1_FULL_REMOTE = 0x3e, /* | 001|11110| */
144 SM5502_MUIC_ADC_AUDIO_TYPE1_SEND_END = 0x5e, /* | 010|11110| */
145 /* |Dev Type1|--ADC| */
146 SM5502_MUIC_ADC_GROUND_USB_OTG = 0x80, /* | 100|00000| */
147 SM5502_MUIC_ADC_OPEN_USB = 0x5f, /* | 010|11111| */
148 SM5502_MUIC_ADC_OPEN_TA = 0xdf, /* | 110|11111| */
149 SM5502_MUIC_ADC_OPEN_USB_OTG = 0xff, /* | 111|11111| */
152 /* List of supported interrupt for SM5502 */
153 static struct muic_irq sm5502_muic_irqs[] = {
154 { SM5502_IRQ_INT1_ATTACH, "muic-attach" },
155 { SM5502_IRQ_INT1_DETACH, "muic-detach" },
156 { SM5502_IRQ_INT1_KP, "muic-kp" },
157 { SM5502_IRQ_INT1_LKP, "muic-lkp" },
158 { SM5502_IRQ_INT1_LKR, "muic-lkr" },
159 { SM5502_IRQ_INT1_OVP_EVENT, "muic-ovp-event" },
160 { SM5502_IRQ_INT1_OCP_EVENT, "muic-ocp-event" },
161 { SM5502_IRQ_INT1_OVP_OCP_DIS, "muic-ovp-ocp-dis" },
162 { SM5502_IRQ_INT2_VBUS_DET, "muic-vbus-det" },
163 { SM5502_IRQ_INT2_REV_ACCE, "muic-rev-acce" },
164 { SM5502_IRQ_INT2_ADC_CHG, "muic-adc-chg" },
165 { SM5502_IRQ_INT2_STUCK_KEY, "muic-stuck-key" },
166 { SM5502_IRQ_INT2_STUCK_KEY_RCV, "muic-stuck-key-rcv" },
167 { SM5502_IRQ_INT2_MHL, "muic-mhl" },
170 /* Define interrupt list of SM5502 to register regmap_irq */
171 static const struct regmap_irq sm5502_irqs[] = {
172 /* INT1 interrupts */
173 { .reg_offset = 0, .mask = SM5502_IRQ_INT1_ATTACH_MASK, },
174 { .reg_offset = 0, .mask = SM5502_IRQ_INT1_DETACH_MASK, },
175 { .reg_offset = 0, .mask = SM5502_IRQ_INT1_KP_MASK, },
176 { .reg_offset = 0, .mask = SM5502_IRQ_INT1_LKP_MASK, },
177 { .reg_offset = 0, .mask = SM5502_IRQ_INT1_LKR_MASK, },
178 { .reg_offset = 0, .mask = SM5502_IRQ_INT1_OVP_EVENT_MASK, },
179 { .reg_offset = 0, .mask = SM5502_IRQ_INT1_OCP_EVENT_MASK, },
180 { .reg_offset = 0, .mask = SM5502_IRQ_INT1_OVP_OCP_DIS_MASK, },
182 /* INT2 interrupts */
183 { .reg_offset = 1, .mask = SM5502_IRQ_INT2_VBUS_DET_MASK,},
184 { .reg_offset = 1, .mask = SM5502_IRQ_INT2_REV_ACCE_MASK, },
185 { .reg_offset = 1, .mask = SM5502_IRQ_INT2_ADC_CHG_MASK, },
186 { .reg_offset = 1, .mask = SM5502_IRQ_INT2_STUCK_KEY_MASK, },
187 { .reg_offset = 1, .mask = SM5502_IRQ_INT2_STUCK_KEY_RCV_MASK, },
188 { .reg_offset = 1, .mask = SM5502_IRQ_INT2_MHL_MASK, },
191 static const struct regmap_irq_chip sm5502_muic_irq_chip = {
193 .status_base = SM5502_REG_INT1,
194 .mask_base = SM5502_REG_INTMASK1,
195 .mask_invert = false,
198 .num_irqs = ARRAY_SIZE(sm5502_irqs),
201 /* Define regmap configuration of SM5502 for I2C communication */
202 static bool sm5502_muic_volatile_reg(struct device *dev, unsigned int reg)
205 case SM5502_REG_INTMASK1:
206 case SM5502_REG_INTMASK2:
214 static const struct regmap_config sm5502_muic_regmap_config = {
217 .volatile_reg = sm5502_muic_volatile_reg,
218 .max_register = SM5502_REG_END,
221 /* Change DM_CON/DP_CON/VBUSIN switch according to cable type */
222 static int sm5502_muic_set_path(struct sm5502_muic_info *info,
223 unsigned int con_sw, unsigned int vbus_sw,
229 con_sw = DM_DP_SWITCH_OPEN;
230 vbus_sw = VBUSIN_SWITCH_OPEN;
234 case DM_DP_SWITCH_OPEN:
235 case DM_DP_SWITCH_USB:
236 case DM_DP_SWITCH_AUDIO:
237 case DM_DP_SWITCH_UART:
238 ret = regmap_update_bits(info->regmap, SM5502_REG_MANUAL_SW1,
239 SM5502_REG_MANUAL_SW1_DP_MASK |
240 SM5502_REG_MANUAL_SW1_DM_MASK,
244 "cannot update DM_CON/DP_CON switch\n");
249 dev_err(info->dev, "Unknown DM_CON/DP_CON switch type (%d)\n",
255 case VBUSIN_SWITCH_OPEN:
256 case VBUSIN_SWITCH_VBUSOUT:
257 case VBUSIN_SWITCH_MIC:
258 case VBUSIN_SWITCH_VBUSOUT_WITH_USB:
259 ret = regmap_update_bits(info->regmap, SM5502_REG_MANUAL_SW1,
260 SM5502_REG_MANUAL_SW1_VBUSIN_MASK,
264 "cannot update VBUSIN switch\n");
269 dev_err(info->dev, "Unknown VBUS switch type (%d)\n", vbus_sw);
276 /* Return cable type of attached or detached accessories */
277 static unsigned int sm5502_muic_get_cable_type(struct sm5502_muic_info *info)
279 unsigned int cable_type, adc, dev_type1;
282 /* Read ADC value according to external cable or button */
283 ret = regmap_read(info->regmap, SM5502_REG_ADC, &adc);
285 dev_err(info->dev, "failed to read ADC register\n");
290 * If ADC is SM5502_MUIC_ADC_GROUND(0x0), external cable hasn't
291 * connected with to MUIC device.
293 cable_type = adc & SM5502_REG_ADC_MASK;
295 switch (cable_type) {
296 case SM5502_MUIC_ADC_GROUND:
297 ret = regmap_read(info->regmap, SM5502_REG_DEV_TYPE1,
300 dev_err(info->dev, "failed to read DEV_TYPE1 reg\n");
305 case SM5502_REG_DEV_TYPE1_USB_OTG_MASK:
306 cable_type = SM5502_MUIC_ADC_GROUND_USB_OTG;
310 "cannot identify the cable type: adc(0x%x), dev_type1(0x%x)\n",
315 case SM5502_MUIC_ADC_SEND_END_BUTTON:
316 case SM5502_MUIC_ADC_REMOTE_S1_BUTTON:
317 case SM5502_MUIC_ADC_REMOTE_S2_BUTTON:
318 case SM5502_MUIC_ADC_REMOTE_S3_BUTTON:
319 case SM5502_MUIC_ADC_REMOTE_S4_BUTTON:
320 case SM5502_MUIC_ADC_REMOTE_S5_BUTTON:
321 case SM5502_MUIC_ADC_REMOTE_S6_BUTTON:
322 case SM5502_MUIC_ADC_REMOTE_S7_BUTTON:
323 case SM5502_MUIC_ADC_REMOTE_S8_BUTTON:
324 case SM5502_MUIC_ADC_REMOTE_S9_BUTTON:
325 case SM5502_MUIC_ADC_REMOTE_S10_BUTTON:
326 case SM5502_MUIC_ADC_REMOTE_S11_BUTTON:
327 case SM5502_MUIC_ADC_REMOTE_S12_BUTTON:
328 case SM5502_MUIC_ADC_RESERVED_ACC_1:
329 case SM5502_MUIC_ADC_RESERVED_ACC_2:
330 case SM5502_MUIC_ADC_RESERVED_ACC_3:
331 case SM5502_MUIC_ADC_RESERVED_ACC_4:
332 case SM5502_MUIC_ADC_RESERVED_ACC_5:
333 case SM5502_MUIC_ADC_AUDIO_TYPE2:
334 case SM5502_MUIC_ADC_PHONE_POWERED_DEV:
335 case SM5502_MUIC_ADC_TTY_CONVERTER:
336 case SM5502_MUIC_ADC_UART_CABLE:
337 case SM5502_MUIC_ADC_TYPE1_CHARGER:
338 case SM5502_MUIC_ADC_FACTORY_MODE_BOOT_OFF_USB:
339 case SM5502_MUIC_ADC_FACTORY_MODE_BOOT_ON_USB:
340 case SM5502_MUIC_ADC_AUDIO_VIDEO_CABLE:
341 case SM5502_MUIC_ADC_TYPE2_CHARGER:
342 case SM5502_MUIC_ADC_FACTORY_MODE_BOOT_OFF_UART:
343 case SM5502_MUIC_ADC_FACTORY_MODE_BOOT_ON_UART:
345 case SM5502_MUIC_ADC_AUDIO_TYPE1:
347 * Check whether cable type is
348 * SM5502_MUIC_ADC_AUDIO_TYPE1_FULL_REMOTE
349 * or SM5502_MUIC_ADC_AUDIO_TYPE1_SEND_END
350 * by using Button event.
353 case SM5502_MUIC_ADC_OPEN:
354 ret = regmap_read(info->regmap, SM5502_REG_DEV_TYPE1,
357 dev_err(info->dev, "failed to read DEV_TYPE1 reg\n");
362 case SM5502_REG_DEV_TYPE1_USB_SDP_MASK:
363 cable_type = SM5502_MUIC_ADC_OPEN_USB;
365 case SM5502_REG_DEV_TYPE1_DEDICATED_CHG_MASK:
366 cable_type = SM5502_MUIC_ADC_OPEN_TA;
368 case SM5502_REG_DEV_TYPE1_USB_OTG_MASK:
369 cable_type = SM5502_MUIC_ADC_OPEN_USB_OTG;
373 "cannot identify the cable type: adc(0x%x)\n",
380 "failed to identify the cable type: adc(0x%x)\n", adc);
387 static int sm5502_muic_cable_handler(struct sm5502_muic_info *info,
390 static unsigned int prev_cable_type = SM5502_MUIC_ADC_GROUND;
391 unsigned int cable_type = SM5502_MUIC_ADC_GROUND;
392 unsigned int con_sw = DM_DP_SWITCH_OPEN;
393 unsigned int vbus_sw = VBUSIN_SWITCH_OPEN;
397 /* Get the type of attached or detached cable */
399 cable_type = sm5502_muic_get_cable_type(info);
401 cable_type = prev_cable_type;
402 prev_cable_type = cable_type;
404 switch (cable_type) {
405 case SM5502_MUIC_ADC_OPEN_USB:
407 con_sw = DM_DP_SWITCH_USB;
408 vbus_sw = VBUSIN_SWITCH_VBUSOUT_WITH_USB;
410 case SM5502_MUIC_ADC_OPEN_TA:
411 id = EXTCON_CHG_USB_DCP;
412 con_sw = DM_DP_SWITCH_OPEN;
413 vbus_sw = VBUSIN_SWITCH_VBUSOUT;
415 case SM5502_MUIC_ADC_GROUND_USB_OTG:
416 case SM5502_MUIC_ADC_OPEN_USB_OTG:
417 id = EXTCON_USB_HOST;
418 con_sw = DM_DP_SWITCH_USB;
419 vbus_sw = VBUSIN_SWITCH_OPEN;
423 "cannot handle this cable_type (0x%x)\n", cable_type);
427 /* Change internal hardware path(DM_CON/DP_CON, VBUSIN) */
428 ret = sm5502_muic_set_path(info, con_sw, vbus_sw, attached);
432 /* Change the state of external accessory */
433 extcon_set_state_sync(info->edev, id, attached);
434 if (id == EXTCON_USB)
435 extcon_set_state_sync(info->edev, EXTCON_CHG_USB_SDP,
441 static void sm5502_muic_irq_work(struct work_struct *work)
443 struct sm5502_muic_info *info = container_of(work,
444 struct sm5502_muic_info, irq_work);
450 mutex_lock(&info->mutex);
452 /* Detect attached or detached cables */
453 if (info->irq_attach) {
454 ret = sm5502_muic_cable_handler(info, true);
455 info->irq_attach = false;
457 if (info->irq_detach) {
458 ret = sm5502_muic_cable_handler(info, false);
459 info->irq_detach = false;
463 dev_err(info->dev, "failed to handle MUIC interrupt\n");
465 mutex_unlock(&info->mutex);
469 * Sets irq_attach or irq_detach in sm5502_muic_info and returns 0.
470 * Returns -ESRCH if irq_type does not match registered IRQ for this dev type.
472 static int sm5502_parse_irq(struct sm5502_muic_info *info, int irq_type)
475 case SM5502_IRQ_INT1_ATTACH:
476 info->irq_attach = true;
478 case SM5502_IRQ_INT1_DETACH:
479 info->irq_detach = true;
481 case SM5502_IRQ_INT1_KP:
482 case SM5502_IRQ_INT1_LKP:
483 case SM5502_IRQ_INT1_LKR:
484 case SM5502_IRQ_INT1_OVP_EVENT:
485 case SM5502_IRQ_INT1_OCP_EVENT:
486 case SM5502_IRQ_INT1_OVP_OCP_DIS:
487 case SM5502_IRQ_INT2_VBUS_DET:
488 case SM5502_IRQ_INT2_REV_ACCE:
489 case SM5502_IRQ_INT2_ADC_CHG:
490 case SM5502_IRQ_INT2_STUCK_KEY:
491 case SM5502_IRQ_INT2_STUCK_KEY_RCV:
492 case SM5502_IRQ_INT2_MHL:
500 static irqreturn_t sm5502_muic_irq_handler(int irq, void *data)
502 struct sm5502_muic_info *info = data;
503 int i, irq_type = -1, ret;
505 for (i = 0; i < info->num_muic_irqs; i++)
506 if (irq == info->muic_irqs[i].virq)
507 irq_type = info->muic_irqs[i].irq;
509 ret = sm5502_parse_irq(info, irq_type);
511 dev_warn(info->dev, "cannot handle is interrupt:%d\n",
515 schedule_work(&info->irq_work);
520 static void sm5502_muic_detect_cable_wq(struct work_struct *work)
522 struct sm5502_muic_info *info = container_of(to_delayed_work(work),
523 struct sm5502_muic_info, wq_detcable);
526 /* Notify the state of connector cable or not */
527 ret = sm5502_muic_cable_handler(info, true);
529 dev_warn(info->dev, "failed to detect cable state\n");
532 static void sm5502_init_dev_type(struct sm5502_muic_info *info)
534 unsigned int reg_data, vendor_id, version_id;
537 /* To test I2C, Print version_id and vendor_id of SM5502 */
538 ret = regmap_read(info->regmap, SM5502_REG_DEVICE_ID, ®_data);
541 "failed to read DEVICE_ID register: %d\n", ret);
545 vendor_id = ((reg_data & SM5502_REG_DEVICE_ID_VENDOR_MASK) >>
546 SM5502_REG_DEVICE_ID_VENDOR_SHIFT);
547 version_id = ((reg_data & SM5502_REG_DEVICE_ID_VERSION_MASK) >>
548 SM5502_REG_DEVICE_ID_VERSION_SHIFT);
550 dev_info(info->dev, "Device type: version: 0x%x, vendor: 0x%x\n",
551 version_id, vendor_id);
553 /* Initiazle the register of SM5502 device to bring-up */
554 for (i = 0; i < info->num_reg_data; i++) {
555 unsigned int val = 0;
557 if (!info->reg_data[i].invert)
558 val |= ~info->reg_data[i].val;
560 val = info->reg_data[i].val;
561 regmap_write(info->regmap, info->reg_data[i].reg, val);
565 static int sm5022_muic_i2c_probe(struct i2c_client *i2c)
567 struct device_node *np = i2c->dev.of_node;
568 struct sm5502_muic_info *info;
569 int i, ret, irq_flags;
574 info = devm_kzalloc(&i2c->dev, sizeof(*info), GFP_KERNEL);
577 i2c_set_clientdata(i2c, info);
579 info->dev = &i2c->dev;
581 info->irq = i2c->irq;
582 info->muic_irqs = sm5502_muic_irqs;
583 info->num_muic_irqs = ARRAY_SIZE(sm5502_muic_irqs);
584 info->reg_data = sm5502_reg_data;
585 info->num_reg_data = ARRAY_SIZE(sm5502_reg_data);
587 mutex_init(&info->mutex);
589 INIT_WORK(&info->irq_work, sm5502_muic_irq_work);
591 info->regmap = devm_regmap_init_i2c(i2c, &sm5502_muic_regmap_config);
592 if (IS_ERR(info->regmap)) {
593 ret = PTR_ERR(info->regmap);
594 dev_err(info->dev, "failed to allocate register map: %d\n",
599 /* Support irq domain for SM5502 MUIC device */
600 irq_flags = IRQF_TRIGGER_FALLING | IRQF_ONESHOT | IRQF_SHARED;
601 ret = devm_regmap_add_irq_chip(info->dev, info->regmap, info->irq, irq_flags,
602 0, &sm5502_muic_irq_chip, &info->irq_data);
604 dev_err(info->dev, "failed to request IRQ %d: %d\n",
609 for (i = 0; i < info->num_muic_irqs; i++) {
610 struct muic_irq *muic_irq = &info->muic_irqs[i];
613 virq = regmap_irq_get_virq(info->irq_data, muic_irq->irq);
616 muic_irq->virq = virq;
618 ret = devm_request_threaded_irq(info->dev, virq, NULL,
619 sm5502_muic_irq_handler,
620 IRQF_NO_SUSPEND | IRQF_ONESHOT,
621 muic_irq->name, info);
624 "failed: irq request (IRQ: %d, error :%d)\n",
630 /* Allocate extcon device */
631 info->edev = devm_extcon_dev_allocate(info->dev, sm5502_extcon_cable);
632 if (IS_ERR(info->edev)) {
633 dev_err(info->dev, "failed to allocate memory for extcon\n");
637 /* Register extcon device */
638 ret = devm_extcon_dev_register(info->dev, info->edev);
640 dev_err(info->dev, "failed to register extcon device\n");
645 * Detect accessory after completing the initialization of platform
647 * - Use delayed workqueue to detect cable state and then
648 * notify cable state to notifiee/platform through uevent.
649 * After completing the booting of platform, the extcon provider
650 * driver should notify cable state to upper layer.
652 INIT_DELAYED_WORK(&info->wq_detcable, sm5502_muic_detect_cable_wq);
653 queue_delayed_work(system_power_efficient_wq, &info->wq_detcable,
654 msecs_to_jiffies(DELAY_MS_DEFAULT));
656 /* Initialize SM5502 device and print vendor id and version id */
657 sm5502_init_dev_type(info);
662 static const struct of_device_id sm5502_dt_match[] = {
663 { .compatible = "siliconmitus,sm5502-muic" },
666 MODULE_DEVICE_TABLE(of, sm5502_dt_match);
668 #ifdef CONFIG_PM_SLEEP
669 static int sm5502_muic_suspend(struct device *dev)
671 struct i2c_client *i2c = to_i2c_client(dev);
672 struct sm5502_muic_info *info = i2c_get_clientdata(i2c);
674 enable_irq_wake(info->irq);
679 static int sm5502_muic_resume(struct device *dev)
681 struct i2c_client *i2c = to_i2c_client(dev);
682 struct sm5502_muic_info *info = i2c_get_clientdata(i2c);
684 disable_irq_wake(info->irq);
690 static SIMPLE_DEV_PM_OPS(sm5502_muic_pm_ops,
691 sm5502_muic_suspend, sm5502_muic_resume);
693 static const struct i2c_device_id sm5502_i2c_id[] = {
694 { "sm5502", TYPE_SM5502 },
697 MODULE_DEVICE_TABLE(i2c, sm5502_i2c_id);
699 static struct i2c_driver sm5502_muic_i2c_driver = {
702 .pm = &sm5502_muic_pm_ops,
703 .of_match_table = sm5502_dt_match,
705 .probe_new = sm5022_muic_i2c_probe,
706 .id_table = sm5502_i2c_id,
709 static int __init sm5502_muic_i2c_init(void)
711 return i2c_add_driver(&sm5502_muic_i2c_driver);
713 subsys_initcall(sm5502_muic_i2c_init);
715 MODULE_DESCRIPTION("Silicon Mitus SM5502 Extcon driver");
716 MODULE_AUTHOR("Chanwoo Choi <cw00.choi@samsung.com>");
717 MODULE_LICENSE("GPL");