arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi

   1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
   2 /*
   3  * Google Gru (and derivatives) board device tree source
   4  *
   5  * Copyright 2016-2017 Google, Inc
   6  */
   7
   8 #include <dt-bindings/input/input.h>
   9 #include "rk3399.dtsi"
  10 #include "rk3399-op1-opp.dtsi"
  11
  12 / {
  13         aliases {
  14                 mmc0 = &sdmmc;
  15                 mmc1 = &sdhci;
  16         };
  17
  18         chosen {
  19                 stdout-path = "serial2:115200n8";
  20         };
  21
  22         /*
  23          * Power Tree
  24          *
  25          * In general an attempt is made to include all rails called out by
  26          * the schematic as long as those rails interact in some way with
  27          * the AP.  AKA:
  28          * - Rails that only connect to the EC (or devices that the EC talks to)
  29          *   are not included.
  30          * - Rails _are_ included if the rails go to the AP even if the AP
  31          *   doesn't currently care about them / they are always on.  The idea
  32          *   here is that it makes it easier to map to the schematic or extend
  33          *   later.
  34          *
  35          * If two rails are substantially the same from the AP's point of
  36          * view, though, we won't create a full fixed regulator.  We'll just
  37          * put the child rail as an alias of the parent rail.  Sometimes rails
  38          * look the same to the AP because one of these is true:
  39          * - The EC controls the enable and the EC always enables a rail as
  40          *   long as the AP is running.
  41          * - The rails are actually connected to each other by a jumper and
  42          *   the distinction is just there to add clarity/flexibility to the
  43          *   schematic.
  44          */
  45
  46         ppvar_sys: ppvar-sys {
  47                 compatible = "regulator-fixed";
  48                 regulator-name = "ppvar_sys";
  49                 regulator-always-on;
  50                 regulator-boot-on;
  51         };
  52
  53         pp1200_lpddr: pp1200-lpddr {
  54                 compatible = "regulator-fixed";
  55                 regulator-name = "pp1200_lpddr";
  56
  57                 /* EC turns on w/ lpddr_pwr_en; always on for AP */
  58                 regulator-always-on;
  59                 regulator-boot-on;
  60                 regulator-min-microvolt = <1200000>;
  61                 regulator-max-microvolt = <1200000>;
  62
  63                 vin-supply = <&ppvar_sys>;
  64         };
  65
  66         pp1800: pp1800 {
  67                 compatible = "regulator-fixed";
  68                 regulator-name = "pp1800";
  69
  70                 /* Always on when ppvar_sys shows power good */
  71                 regulator-always-on;
  72                 regulator-boot-on;
  73                 regulator-min-microvolt = <1800000>;
  74                 regulator-max-microvolt = <1800000>;
  75
  76                 vin-supply = <&ppvar_sys>;
  77         };
  78
  79         pp3300: pp3300 {
  80                 compatible = "regulator-fixed";
  81                 regulator-name = "pp3300";
  82
  83                 /* Always on; plain and simple */
  84                 regulator-always-on;
  85                 regulator-boot-on;
  86                 regulator-min-microvolt = <3300000>;
  87                 regulator-max-microvolt = <3300000>;
  88
  89                 vin-supply = <&ppvar_sys>;
  90         };
  91
  92         pp5000: pp5000 {
  93                 compatible = "regulator-fixed";
  94                 regulator-name = "pp5000";
  95
  96                 /* EC turns on w/ pp5000_en; always on for AP */
  97                 regulator-always-on;
  98                 regulator-boot-on;
  99                 regulator-min-microvolt = <5000000>;
 100                 regulator-max-microvolt = <5000000>;
 101
 102                 vin-supply = <&ppvar_sys>;
 103         };
 104
 105         ppvar_bigcpu_pwm: ppvar-bigcpu-pwm {
 106                 compatible = "pwm-regulator";
 107                 regulator-name = "ppvar_bigcpu_pwm";
 108
 109                 pwms = <&pwm1 0 3337 0>;
 110                 pwm-supply = <&ppvar_sys>;
 111                 pwm-dutycycle-range = <100 0>;
 112                 pwm-dutycycle-unit = <100>;
 113
 114                 /* EC turns on w/ ap_core_en; always on for AP */
 115                 regulator-always-on;
 116                 regulator-boot-on;
 117                 regulator-min-microvolt = <800107>;
 118                 regulator-max-microvolt = <1302232>;
 119         };
 120
 121         ppvar_bigcpu: ppvar-bigcpu {
 122                 compatible = "vctrl-regulator";
 123                 regulator-name = "ppvar_bigcpu";
 124
 125                 regulator-min-microvolt = <800107>;
 126                 regulator-max-microvolt = <1302232>;
 127
 128                 ctrl-supply = <&ppvar_bigcpu_pwm>;
 129                 ctrl-voltage-range = <800107 1302232>;
 130
 131                 regulator-settling-time-up-us = <322>;
 132         };
 133
 134         ppvar_litcpu_pwm: ppvar-litcpu-pwm {
 135                 compatible = "pwm-regulator";
 136                 regulator-name = "ppvar_litcpu_pwm";
 137
 138                 pwms = <&pwm2 0 3337 0>;
 139                 pwm-supply = <&ppvar_sys>;
 140                 pwm-dutycycle-range = <100 0>;
 141                 pwm-dutycycle-unit = <100>;
 142
 143                 /* EC turns on w/ ap_core_en; always on for AP */
 144                 regulator-always-on;
 145                 regulator-boot-on;
 146                 regulator-min-microvolt = <797743>;
 147                 regulator-max-microvolt = <1307837>;
 148         };
 149
 150         ppvar_litcpu: ppvar-litcpu {
 151                 compatible = "vctrl-regulator";
 152                 regulator-name = "ppvar_litcpu";
 153
 154                 regulator-min-microvolt = <797743>;
 155                 regulator-max-microvolt = <1307837>;
 156
 157                 ctrl-supply = <&ppvar_litcpu_pwm>;
 158                 ctrl-voltage-range = <797743 1307837>;
 159
 160                 regulator-settling-time-up-us = <384>;
 161         };
 162
 163         ppvar_gpu_pwm: ppvar-gpu-pwm {
 164                 compatible = "pwm-regulator";
 165                 regulator-name = "ppvar_gpu_pwm";
 166
 167                 pwms = <&pwm0 0 3337 0>;
 168                 pwm-supply = <&ppvar_sys>;
 169                 pwm-dutycycle-range = <100 0>;
 170                 pwm-dutycycle-unit = <100>;
 171
 172                 /* EC turns on w/ ap_core_en; always on for AP */
 173                 regulator-always-on;
 174                 regulator-boot-on;
 175                 regulator-min-microvolt = <786384>;
 176                 regulator-max-microvolt = <1217747>;
 177         };
 178
 179         ppvar_gpu: ppvar-gpu {
 180                 compatible = "vctrl-regulator";
 181                 regulator-name = "ppvar_gpu";
 182
 183                 regulator-min-microvolt = <786384>;
 184                 regulator-max-microvolt = <1217747>;
 185
 186                 ctrl-supply = <&ppvar_gpu_pwm>;
 187                 ctrl-voltage-range = <786384 1217747>;
 188
 189                 regulator-settling-time-up-us = <390>;
 190         };
 191
 192         /* EC turns on w/ pp900_ddrpll_en */
 193         pp900_ddrpll: pp900-ap {
 194         };
 195
 196         /* EC turns on w/ pp900_pll_en */
 197         pp900_pll: pp900-ap {
 198         };
 199
 200         /* EC turns on w/ pp900_pmu_en */
 201         pp900_pmu: pp900-ap {
 202         };
 203
 204         /* EC turns on w/ pp1800_s0_en_l */
 205         pp1800_ap_io: pp1800_emmc: pp1800_nfc: pp1800_s0: pp1800 {
 206         };
 207
 208         /* EC turns on w/ pp1800_avdd_en_l */
 209         pp1800_avdd: pp1800 {
 210         };
 211
 212         /* EC turns on w/ pp1800_lid_en_l */
 213         pp1800_lid: pp1800_mic: pp1800 {
 214         };
 215
 216         /* EC turns on w/ lpddr_pwr_en */
 217         pp1800_lpddr: pp1800 {
 218         };
 219
 220         /* EC turns on w/ pp1800_pmu_en_l */
 221         pp1800_pmu: pp1800 {
 222         };
 223
 224         /* EC turns on w/ pp1800_usb_en_l */
 225         pp1800_usb: pp1800 {
 226         };
 227
 228         pp3000_sd_slot: pp3000-sd-slot {
 229                 compatible = "regulator-fixed";
 230                 regulator-name = "pp3000_sd_slot";
 231                 pinctrl-names = "default";
 232                 pinctrl-0 = <&sd_slot_pwr_en>;
 233
 234                 enable-active-high;
 235                 gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;
 236
 237                 vin-supply = <&pp3000>;
 238         };
 239
 240         /*
 241          * Technically, this is a small abuse of 'regulator-gpio'; this
 242          * regulator is a mux between pp1800 and pp3300. pp1800 and pp3300 are
 243          * always on though, so it is sufficient to simply control the mux
 244          * here.
 245          */
 246         ppvar_sd_card_io: ppvar-sd-card-io {
 247                 compatible = "regulator-gpio";
 248                 regulator-name = "ppvar_sd_card_io";
 249                 pinctrl-names = "default";
 250                 pinctrl-0 = <&sd_io_pwr_en &sd_pwr_1800_sel>;
 251
 252                 enable-active-high;
 253                 enable-gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
 254                 gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
 255                 states = <1800000 0x1
 256                           3000000 0x0>;
 257
 258                 regulator-min-microvolt = <1800000>;
 259                 regulator-max-microvolt = <3000000>;
 260         };
 261
 262         /* EC turns on w/ pp3300_trackpad_en_l */
 263         pp3300_trackpad: pp3300-trackpad {
 264         };
 265
 266         /* EC turns on w/ usb_a_en */
 267         pp5000_usb_a_vbus: pp5000 {
 268         };
 269
 270         ap_rtc_clk: ap-rtc-clk {
 271                 compatible = "fixed-clock";
 272                 clock-frequency = <32768>;
 273                 clock-output-names = "xin32k";
 274                 #clock-cells = <0>;
 275         };
 276
 277         max98357a: max98357a {
 278                 compatible = "maxim,max98357a";
 279                 pinctrl-names = "default";
 280                 pinctrl-0 = <&sdmode_en>;
 281                 sdmode-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 282                 sdmode-delay = <2>;
 283                 #sound-dai-cells = <0>;
 284                 status = "okay";
 285         };
 286
 287         sound: sound {
 288                 compatible = "rockchip,rk3399-gru-sound";
 289                 rockchip,cpu = <&i2s0 &i2s2>;
 290         };
 291 };
 292
 293 &cdn_dp {
 294         status = "okay";
 295 };
 296
 297 /*
 298  * Set some suspend operating points to avoid OVP in suspend
 299  *
 300  * When we go into S3 ARM Trusted Firmware will transition our PWM regulators
 301  * from wherever they're at back to the "default" operating point (whatever
 302  * voltage we get when we set the PWM pins to "input").
 303  *
 304  * This quick transition under light load has the possibility to trigger the
 305  * regulator "over voltage protection" (OVP).
 306  *
 307  * To make extra certain that we don't hit this OVP at suspend time, we'll
 308  * transition to a voltage that's much closer to the default (~1.0 V) so that
 309  * there will not be a big jump.  Technically we only need to get within 200 mV
 310  * of the default voltage, but the speed here should be fast enough and we need
 311  * suspend/resume to be rock solid.
 312  */
 313
 314 &cluster0_opp {
 315         opp05 {
 316                 opp-suspend;
 317         };
 318 };
 319
 320 &cluster1_opp {
 321         opp06 {
 322                 opp-suspend;
 323         };
 324 };
 325
 326 &cpu_l0 {
 327         cpu-supply = <&ppvar_litcpu>;
 328 };
 329
 330 &cpu_l1 {
 331         cpu-supply = <&ppvar_litcpu>;
 332 };
 333
 334 &cpu_l2 {
 335         cpu-supply = <&ppvar_litcpu>;
 336 };
 337
 338 &cpu_l3 {
 339         cpu-supply = <&ppvar_litcpu>;
 340 };
 341
 342 &cpu_b0 {
 343         cpu-supply = <&ppvar_bigcpu>;
 344 };
 345
 346 &cpu_b1 {
 347         cpu-supply = <&ppvar_bigcpu>;
 348 };
 349
 350
 351 &cru {
 352         assigned-clocks =
 353                 <&cru PLL_GPLL>, <&cru PLL_CPLL>,
 354                 <&cru PLL_NPLL>,
 355                 <&cru ACLK_PERIHP>, <&cru HCLK_PERIHP>,
 356                 <&cru PCLK_PERIHP>,
 357                 <&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>,
 358                 <&cru PCLK_PERILP0>, <&cru ACLK_CCI>,
 359                 <&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>,
 360                 <&cru ACLK_VIO>, <&cru ACLK_HDCP>,
 361                 <&cru ACLK_GIC_PRE>,
 362                 <&cru PCLK_DDR>;
 363         assigned-clock-rates =
 364                 <600000000>, <800000000>,
 365                 <1000000000>,
 366                 <150000000>, <75000000>,
 367                 <37500000>,
 368                 <100000000>, <100000000>,
 369                 <50000000>, <800000000>,
 370                 <100000000>, <50000000>,
 371                 <400000000>, <400000000>,
 372                 <200000000>,
 373                 <200000000>;
 374 };
 375
 376 &emmc_phy {
 377         status = "okay";
 378 };
 379
 380 &gpu {
 381         mali-supply = <&ppvar_gpu>;
 382         status = "okay";
 383 };
 384
 385 ap_i2c_ts: &i2c3 {
 386         status = "okay";
 387
 388         clock-frequency = <400000>;
 389
 390         /* These are relatively safe rise/fall times */
 391         i2c-scl-falling-time-ns = <50>;
 392         i2c-scl-rising-time-ns = <300>;
 393 };
 394
 395 ap_i2c_audio: &i2c8 {
 396         status = "okay";
 397
 398         clock-frequency = <400000>;
 399
 400         /* These are relatively safe rise/fall times */
 401         i2c-scl-falling-time-ns = <50>;
 402         i2c-scl-rising-time-ns = <300>;
 403
 404         codec: da7219@1a {
 405                 compatible = "dlg,da7219";
 406                 reg = <0x1a>;
 407                 interrupt-parent = <&gpio1>;
 408                 interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
 409                 clocks = <&cru SCLK_I2S_8CH_OUT>;
 410                 clock-names = "mclk";
 411                 dlg,micbias-lvl = <2600>;
 412                 dlg,mic-amp-in-sel = "diff";
 413                 pinctrl-names = "default";
 414                 pinctrl-0 = <&headset_int_l>;
 415                 VDD-supply = <&pp1800>;
 416                 VDDMIC-supply = <&pp3300>;
 417                 VDDIO-supply = <&pp1800>;
 418
 419                 da7219_aad {
 420                         dlg,adc-1bit-rpt = <1>;
 421                         dlg,btn-avg = <4>;
 422                         dlg,btn-cfg = <50>;
 423                         dlg,mic-det-thr = <500>;
 424                         dlg,jack-ins-deb = <20>;
 425                         dlg,jack-det-rate = "32ms_64ms";
 426                         dlg,jack-rem-deb = <1>;
 427
 428                         dlg,a-d-btn-thr = <0xa>;
 429                         dlg,d-b-btn-thr = <0x16>;
 430                         dlg,b-c-btn-thr = <0x21>;
 431                         dlg,c-mic-btn-thr = <0x3E>;
 432                 };
 433         };
 434 };
 435
 436 &i2s0 {
 437         status = "okay";
 438 };
 439
 440 &i2s2 {
 441         status = "okay";
 442 };
 443
 444 &io_domains {
 445         status = "okay";
 446
 447         audio-supply = <&pp1800_audio>;         /* APIO5_VDD;  3d 4a */
 448         bt656-supply = <&pp1800_ap_io>;         /* APIO2_VDD;  2a 2b */
 449         gpio1830-supply = <&pp3000_ap>;         /* APIO4_VDD;  4c 4d */
 450         sdmmc-supply = <&ppvar_sd_card_io>;     /* SDMMC0_VDD; 4b    */
 451 };
 452
 453 &pcie0 {
 454         status = "okay";
 455
 456         ep-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>;
 457         pinctrl-names = "default";
 458         pinctrl-0 = <&pcie_clkreqn_cpm>, <&wifi_perst_l>;
 459         vpcie3v3-supply = <&pp3300_wifi_bt>;
 460         vpcie1v8-supply = <&wlan_pd_n>; /* HACK: see &wlan_pd_n */
 461         vpcie0v9-supply = <&pp900_pcie>;
 462
 463         pci_rootport: pcie@0,0 {
 464                 reg = <0x83000000 0x0 0x00000000 0x0 0x00000000>;
 465                 #address-cells = <3>;
 466                 #size-cells = <2>;
 467                 ranges;
 468         };
 469 };
 470
 471 &pcie_phy {
 472         status = "okay";
 473 };
 474
 475 &pmu_io_domains {
 476         status = "okay";
 477
 478         pmu1830-supply = <&pp1800_pmu>;         /* PMUIO2_VDD */
 479 };
 480
 481 &pwm0 {
 482         status = "okay";
 483 };
 484
 485 &pwm1 {
 486         status = "okay";
 487 };
 488
 489 &pwm2 {
 490         status = "okay";
 491 };
 492
 493 &pwm3 {
 494         status = "okay";
 495 };
 496
 497 &sdhci {
 498         /*
 499          * Signal integrity isn't great at 200 MHz and 150 MHz (DDR) gives the
 500          * same (or nearly the same) performance for all eMMC that are intended
 501          * to be used.
 502          */
 503         assigned-clock-rates = <150000000>;
 504
 505         bus-width = <8>;
 506         mmc-hs400-1_8v;
 507         mmc-hs400-enhanced-strobe;
 508         non-removable;
 509         status = "okay";
 510 };
 511
 512 &sdmmc {
 513         status = "okay";
 514
 515         /*
 516          * Note: configure "sdmmc_cd" as card detect even though it's actually
 517          * hooked to ground.  Because we specified "cd-gpios" below dw_mmc
 518          * should be ignoring card detect anyway.  Specifying the pin as
 519          * sdmmc_cd means that even if you've got GRF_SOC_CON7[12] (force_jtag)
 520          * turned on that the system will still make sure the port is
 521          * configured as SDMMC and not JTAG.
 522          */
 523         pinctrl-names = "default";
 524         pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_cd_pin
 525                      &sdmmc_bus4>;
 526
 527         bus-width = <4>;
 528         cap-mmc-highspeed;
 529         cap-sd-highspeed;
 530         cd-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
 531         disable-wp;
 532         sd-uhs-sdr12;
 533         sd-uhs-sdr25;
 534         sd-uhs-sdr50;
 535         sd-uhs-sdr104;
 536         vmmc-supply = <&pp3000_sd_slot>;
 537         vqmmc-supply = <&ppvar_sd_card_io>;
 538 };
 539
 540 &spi1 {
 541         status = "okay";
 542
 543         pinctrl-names = "default", "sleep";
 544         pinctrl-1 = <&spi1_sleep>;
 545
 546         spiflash@0 {
 547                 compatible = "jedec,spi-nor";
 548                 reg = <0>;
 549
 550                 /* May run faster once verified. */
 551                 spi-max-frequency = <10000000>;
 552         };
 553 };
 554
 555 &spi2 {
 556         status = "okay";
 557 };
 558
 559 &spi5 {
 560         status = "okay";
 561
 562         cros_ec: ec@0 {
 563                 compatible = "google,cros-ec-spi";
 564                 reg = <0>;
 565                 interrupt-parent = <&gpio0>;
 566                 interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
 567                 pinctrl-names = "default";
 568                 pinctrl-0 = <&ec_ap_int_l>;
 569                 spi-max-frequency = <3000000>;
 570
 571                 i2c_tunnel: i2c-tunnel {
 572                         compatible = "google,cros-ec-i2c-tunnel";
 573                         google,remote-bus = <4>;
 574                         #address-cells = <1>;
 575                         #size-cells = <0>;
 576                 };
 577
 578                 usbc_extcon0: extcon0 {
 579                         compatible = "google,extcon-usbc-cros-ec";
 580                         google,usb-port-id = <0>;
 581                 };
 582         };
 583 };
 584
 585 &tsadc {
 586         status = "okay";
 587
 588         rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
 589         rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
 590 };
 591
 592 &tcphy0 {
 593         status = "okay";
 594         extcon = <&usbc_extcon0>;
 595 };
 596
 597 &u2phy0 {
 598         status = "okay";
 599 };
 600
 601 &u2phy0_host {
 602         status = "okay";
 603 };
 604
 605 &u2phy1_host {
 606         status = "okay";
 607 };
 608
 609 &u2phy0_otg {
 610         status = "okay";
 611 };
 612
 613 &u2phy1_otg {
 614         status = "okay";
 615 };
 616
 617 &uart2 {
 618         status = "okay";
 619 };
 620
 621 &usb_host0_ohci {
 622         status = "okay";
 623 };
 624
 625 &usbdrd3_0 {
 626         status = "okay";
 627         extcon = <&usbc_extcon0>;
 628 };
 629
 630 &usbdrd_dwc3_0 {
 631         status = "okay";
 632         dr_mode = "host";
 633 };
 634
 635 &vopb {
 636         status = "okay";
 637 };
 638
 639 &vopb_mmu {
 640         status = "okay";
 641 };
 642
 643 &vopl {
 644         status = "okay";
 645 };
 646
 647 &vopl_mmu {
 648         status = "okay";
 649 };
 650
 651 #include <arm/cros-ec-keyboard.dtsi>
 652 #include <arm/cros-ec-sbs.dtsi>
 653
 654 &pinctrl {
 655         /*
 656          * pinctrl settings for pins that have no real owners.
 657          *
 658          * At the moment settings are identical for S0 and S3, but if we later
 659          * need to configure things differently for S3 we'll adjust here.
 660          */
 661         pinctrl-names = "default";
 662         pinctrl-0 = <
 663                 &ap_pwroff      /* AP will auto-assert this when in S3 */
 664                 &clk_32k        /* This pin is always 32k on gru boards */
 665         >;
 666
 667         pcfg_output_low: pcfg-output-low {
 668                 output-low;
 669         };
 670
 671         pcfg_output_high: pcfg-output-high {
 672                 output-high;
 673         };
 674
 675         pcfg_pull_none_8ma: pcfg-pull-none-8ma {
 676                 bias-disable;
 677                 drive-strength = <8>;
 678         };
 679
 680         backlight-enable {
 681                 bl_en: bl-en {
 682                         rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
 683                 };
 684         };
 685
 686         cros-ec {
 687                 ec_ap_int_l: ec-ap-int-l {
 688                         rockchip,pins = <0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
 689                 };
 690         };
 691
 692         discrete-regulators {
 693                 sd_io_pwr_en: sd-io-pwr-en {
 694                         rockchip,pins = <2 RK_PA2 RK_FUNC_GPIO
 695                                          &pcfg_pull_none>;
 696                 };
 697
 698                 sd_pwr_1800_sel: sd-pwr-1800-sel {
 699                         rockchip,pins = <2 RK_PD4 RK_FUNC_GPIO
 700                                          &pcfg_pull_none>;
 701                 };
 702
 703                 sd_slot_pwr_en: sd-slot-pwr-en {
 704                         rockchip,pins = <4 RK_PD5 RK_FUNC_GPIO
 705                                          &pcfg_pull_none>;
 706                 };
 707         };
 708
 709         codec {
 710                 /* Has external pullup */
 711                 headset_int_l: headset-int-l {
 712                         rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
 713                 };
 714
 715                 mic_int: mic-int {
 716                         rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_down>;
 717                 };
 718         };
 719
 720         max98357a {
 721                 sdmode_en: sdmode-en {
 722                         rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_down>;
 723                 };
 724         };
 725
 726         pcie {
 727                 pcie_clkreqn_cpm: pci-clkreqn-cpm {
 728                         /*
 729                          * Since our pcie doesn't support ClockPM(CPM), we want
 730                          * to hack this as gpio, so the EP could be able to
 731                          * de-assert it along and make ClockPM(CPM) work.
 732                          */
 733                         rockchip,pins = <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
 734                 };
 735         };
 736
 737         sdmmc {
 738                 /*
 739                  * We run sdmmc at max speed; bump up drive strength.
 740                  * We also have external pulls, so disable the internal ones.
 741                  */
 742                 sdmmc_bus4: sdmmc-bus4 {
 743                         rockchip,pins =
 744                                 <4 RK_PB0 1 &pcfg_pull_none_8ma>,
 745                                 <4 RK_PB1 1 &pcfg_pull_none_8ma>,
 746                                 <4 RK_PB2 1 &pcfg_pull_none_8ma>,
 747                                 <4 RK_PB3 1 &pcfg_pull_none_8ma>;
 748                 };
 749
 750                 sdmmc_clk: sdmmc-clk {
 751                         rockchip,pins =
 752                                 <4 RK_PB4 1 &pcfg_pull_none_8ma>;
 753                 };
 754
 755                 sdmmc_cmd: sdmmc-cmd {
 756                         rockchip,pins =
 757                                 <4 RK_PB5 1 &pcfg_pull_none_8ma>;
 758                 };
 759
 760                 /*
 761                  * In our case the official card detect is hooked to ground
 762                  * to avoid getting access to JTAG just by sticking something
 763                  * in the SD card slot (see the force_jtag bit in the TRM).
 764                  *
 765                  * We still configure it as card detect because it doesn't
 766                  * hurt and dw_mmc will ignore it.  We make sure to disable
 767                  * the pull though so we don't burn needless power.
 768                  */
 769                 sdmmc_cd: sdmmc-cd {
 770                         rockchip,pins =
 771                                 <0 RK_PA7 1 &pcfg_pull_none>;
 772                 };
 773
 774                 /* This is where we actually hook up CD; has external pull */
 775                 sdmmc_cd_pin: sdmmc-cd-pin {
 776                         rockchip,pins = <4 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
 777                 };
 778         };
 779
 780         spi1 {
 781                 spi1_sleep: spi1-sleep {
 782                         /*
 783                          * Pull down SPI1 CLK/CS/RX/TX during suspend, to
 784                          * prevent leakage.
 785                          */
 786                         rockchip,pins = <1 RK_PB1 RK_FUNC_GPIO &pcfg_pull_down>,
 787                                         <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_down>,
 788                                         <1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_down>,
 789                                         <1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>;
 790                 };
 791         };
 792
 793         touchscreen {
 794                 touch_int_l: touch-int-l {
 795                         rockchip,pins = <3 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>;
 796                 };
 797
 798                 touch_reset_l: touch-reset-l {
 799                         rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
 800                 };
 801         };
 802
 803         trackpad {
 804                 ap_i2c_tp_pu_en: ap-i2c-tp-pu-en {
 805                         rockchip,pins = <3 RK_PB4 RK_FUNC_GPIO &pcfg_output_high>;
 806                 };
 807
 808                 trackpad_int_l: trackpad-int-l {
 809                         rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>;
 810                 };
 811         };
 812
 813         wifi: wifi {
 814                 wlan_module_reset_l: wlan-module-reset-l {
 815                         rockchip,pins = <1 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
 816                 };
 817
 818                 bt_host_wake_l: bt-host-wake-l {
 819                         /* Kevin has an external pull up, but Gru does not */
 820                         rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
 821                 };
 822         };
 823
 824         write-protect {
 825                 ap_fw_wp: ap-fw-wp {
 826                         rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>;
 827                 };
 828         };
 829 };