arch/arm64/boot/dts/qcom/sdm845-db845c.dts

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Copyright (c) 2019, Linaro Ltd.
   4  */
   5
   6 /dts-v1/;
   7
   8 #include <dt-bindings/gpio/gpio.h>
   9 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
  10 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
  11 #include <dt-bindings/sound/qcom,q6afe.h>
  12 #include <dt-bindings/sound/qcom,q6asm.h>
  13 #include "sdm845.dtsi"
  14 #include "pm8998.dtsi"
  15 #include "pmi8998.dtsi"
  16
  17 / {
  18         model = "Thundercomm Dragonboard 845c";
  19         compatible = "thundercomm,db845c", "qcom,sdm845";
  20
  21         aliases {
  22                 serial0 = &uart9;
  23                 hsuart0 = &uart6;
  24         };
  25
  26         chosen {
  27                 stdout-path = "serial0:115200n8";
  28         };
  29
  30         dc12v: dc12v-regulator {
  31                 compatible = "regulator-fixed";
  32                 regulator-name = "DC12V";
  33                 regulator-min-microvolt = <12000000>;
  34                 regulator-max-microvolt = <12000000>;
  35                 regulator-always-on;
  36         };
  37
  38         gpio_keys {
  39                 compatible = "gpio-keys";
  40                 autorepeat;
  41
  42                 pinctrl-names = "default";
  43                 pinctrl-0 = <&vol_up_pin_a>;
  44
  45                 vol-up {
  46                         label = "Volume Up";
  47                         linux,code = <KEY_VOLUMEUP>;
  48                         gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
  49                 };
  50         };
  51
  52         leds {
  53                 compatible = "gpio-leds";
  54
  55                 user4 {
  56                         label = "green:user4";
  57                         gpios = <&pm8998_gpio 13 GPIO_ACTIVE_HIGH>;
  58                         linux,default-trigger = "panic-indicator";
  59                         default-state = "off";
  60                 };
  61
  62                 wlan {
  63                         label = "yellow:wlan";
  64                         gpios = <&pm8998_gpio 9 GPIO_ACTIVE_HIGH>;
  65                         linux,default-trigger = "phy0tx";
  66                         default-state = "off";
  67                 };
  68
  69                 bt {
  70                         label = "blue:bt";
  71                         gpios = <&pm8998_gpio 5 GPIO_ACTIVE_HIGH>;
  72                         linux,default-trigger = "bluetooth-power";
  73                         default-state = "off";
  74                 };
  75         };
  76
  77         lt9611_1v8: lt9611-vdd18-regulator {
  78                 compatible = "regulator-fixed";
  79                 regulator-name = "LT9611_1V8";
  80
  81                 vin-supply = <&vdc_5v>;
  82                 regulator-min-microvolt = <1800000>;
  83                 regulator-max-microvolt = <1800000>;
  84
  85                 gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
  86                 enable-active-high;
  87         };
  88
  89         lt9611_3v3: lt9611-3v3 {
  90                 compatible = "regulator-fixed";
  91                 regulator-name = "LT9611_3V3";
  92
  93                 vin-supply = <&vdc_3v3>;
  94                 regulator-min-microvolt = <3300000>;
  95                 regulator-max-microvolt = <3300000>;
  96
  97                 // TODO: make it possible to drive same GPIO from two clients
  98                 // gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
  99                 // enable-active-high;
 100         };
 101
 102         pcie0_1p05v: pcie-0-1p05v-regulator {
 103                 compatible = "regulator-fixed";
 104                 regulator-name = "PCIE0_1.05V";
 105
 106                 vin-supply = <&vbat>;
 107                 regulator-min-microvolt = <1050000>;
 108                 regulator-max-microvolt = <1050000>;
 109
 110                 // TODO: make it possible to drive same GPIO from two clients
 111                 // gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>;
 112                 // enable-active-high;
 113         };
 114
 115         pcie0_3p3v_dual: vldo-3v3-regulator {
 116                 compatible = "regulator-fixed";
 117                 regulator-name = "VLDO_3V3";
 118
 119                 vin-supply = <&vbat>;
 120                 regulator-min-microvolt = <3300000>;
 121                 regulator-max-microvolt = <3300000>;
 122
 123                 gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>;
 124                 enable-active-high;
 125
 126                 pinctrl-names = "default";
 127                 pinctrl-0 = <&pcie0_pwren_state>;
 128         };
 129
 130         v5p0_hdmiout: v5p0-hdmiout-regulator {
 131                 compatible = "regulator-fixed";
 132                 regulator-name = "V5P0_HDMIOUT";
 133
 134                 vin-supply = <&vdc_5v>;
 135                 regulator-min-microvolt = <500000>;
 136                 regulator-max-microvolt = <500000>;
 137
 138                 // TODO: make it possible to drive same GPIO from two clients
 139                 // gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
 140                 // enable-active-high;
 141         };
 142
 143         vbat: vbat-regulator {
 144                 compatible = "regulator-fixed";
 145                 regulator-name = "VBAT";
 146
 147                 vin-supply = <&dc12v>;
 148                 regulator-min-microvolt = <4200000>;
 149                 regulator-max-microvolt = <4200000>;
 150                 regulator-always-on;
 151         };
 152
 153         vbat_som: vbat-som-regulator {
 154                 compatible = "regulator-fixed";
 155                 regulator-name = "VBAT_SOM";
 156
 157                 vin-supply = <&dc12v>;
 158                 regulator-min-microvolt = <4200000>;
 159                 regulator-max-microvolt = <4200000>;
 160                 regulator-always-on;
 161         };
 162
 163         vdc_3v3: vdc-3v3-regulator {
 164                 compatible = "regulator-fixed";
 165                 regulator-name = "VDC_3V3";
 166                 vin-supply = <&dc12v>;
 167                 regulator-min-microvolt = <3300000>;
 168                 regulator-max-microvolt = <3300000>;
 169                 regulator-always-on;
 170         };
 171
 172         vdc_5v: vdc-5v-regulator {
 173                 compatible = "regulator-fixed";
 174                 regulator-name = "VDC_5V";
 175
 176                 vin-supply = <&dc12v>;
 177                 regulator-min-microvolt = <500000>;
 178                 regulator-max-microvolt = <500000>;
 179                 regulator-always-on;
 180         };
 181
 182         vreg_s4a_1p8: vreg-s4a-1p8 {
 183                 compatible = "regulator-fixed";
 184                 regulator-name = "vreg_s4a_1p8";
 185
 186                 regulator-min-microvolt = <1800000>;
 187                 regulator-max-microvolt = <1800000>;
 188                 regulator-always-on;
 189         };
 190
 191         vph_pwr: vph-pwr-regulator {
 192                 compatible = "regulator-fixed";
 193                 regulator-name = "vph_pwr";
 194
 195                 vin-supply = <&vbat_som>;
 196         };
 197 };
 198
 199 &adsp_pas {
 200         status = "okay";
 201
 202         firmware-name = "qcom/sdm845/adsp.mdt";
 203 };
 204
 205 &apps_rsc {
 206         pm8998-rpmh-regulators {
 207                 compatible = "qcom,pm8998-rpmh-regulators";
 208                 qcom,pmic-id = "a";
 209                 vdd-s1-supply = <&vph_pwr>;
 210                 vdd-s2-supply = <&vph_pwr>;
 211                 vdd-s3-supply = <&vph_pwr>;
 212                 vdd-s4-supply = <&vph_pwr>;
 213                 vdd-s5-supply = <&vph_pwr>;
 214                 vdd-s6-supply = <&vph_pwr>;
 215                 vdd-s7-supply = <&vph_pwr>;
 216                 vdd-s8-supply = <&vph_pwr>;
 217                 vdd-s9-supply = <&vph_pwr>;
 218                 vdd-s10-supply = <&vph_pwr>;
 219                 vdd-s11-supply = <&vph_pwr>;
 220                 vdd-s12-supply = <&vph_pwr>;
 221                 vdd-s13-supply = <&vph_pwr>;
 222                 vdd-l1-l27-supply = <&vreg_s7a_1p025>;
 223                 vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
 224                 vdd-l3-l11-supply = <&vreg_s7a_1p025>;
 225                 vdd-l4-l5-supply = <&vreg_s7a_1p025>;
 226                 vdd-l6-supply = <&vph_pwr>;
 227                 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
 228                 vdd-l9-supply = <&vreg_bob>;
 229                 vdd-l10-l23-l25-supply = <&vreg_bob>;
 230                 vdd-l13-l19-l21-supply = <&vreg_bob>;
 231                 vdd-l16-l28-supply = <&vreg_bob>;
 232                 vdd-l18-l22-supply = <&vreg_bob>;
 233                 vdd-l20-l24-supply = <&vreg_bob>;
 234                 vdd-l26-supply = <&vreg_s3a_1p35>;
 235                 vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
 236
 237                 vreg_s3a_1p35: smps3 {
 238                         regulator-min-microvolt = <1352000>;
 239                         regulator-max-microvolt = <1352000>;
 240                 };
 241
 242                 vreg_s5a_2p04: smps5 {
 243                         regulator-min-microvolt = <1904000>;
 244                         regulator-max-microvolt = <2040000>;
 245                 };
 246
 247                 vreg_s7a_1p025: smps7 {
 248                         regulator-min-microvolt = <900000>;
 249                         regulator-max-microvolt = <1028000>;
 250                 };
 251
 252                 vreg_l1a_0p875: ldo1 {
 253                         regulator-min-microvolt = <880000>;
 254                         regulator-max-microvolt = <880000>;
 255                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 256                 };
 257
 258                 vreg_l5a_0p8: ldo5 {
 259                         regulator-min-microvolt = <800000>;
 260                         regulator-max-microvolt = <800000>;
 261                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 262                 };
 263
 264                 vreg_l12a_1p8: ldo12 {
 265                         regulator-min-microvolt = <1800000>;
 266                         regulator-max-microvolt = <1800000>;
 267                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 268                 };
 269
 270                 vreg_l7a_1p8: ldo7 {
 271                         regulator-min-microvolt = <1800000>;
 272                         regulator-max-microvolt = <1800000>;
 273                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 274                 };
 275
 276                 vreg_l13a_2p95: ldo13 {
 277                         regulator-min-microvolt = <1800000>;
 278                         regulator-max-microvolt = <2960000>;
 279                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 280                 };
 281
 282                 vreg_l17a_1p3: ldo17 {
 283                         regulator-min-microvolt = <1304000>;
 284                         regulator-max-microvolt = <1304000>;
 285                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 286                 };
 287
 288                 vreg_l20a_2p95: ldo20 {
 289                         regulator-min-microvolt = <2960000>;
 290                         regulator-max-microvolt = <2968000>;
 291                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 292                 };
 293
 294                 vreg_l21a_2p95: ldo21 {
 295                         regulator-min-microvolt = <2960000>;
 296                         regulator-max-microvolt = <2968000>;
 297                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 298                 };
 299
 300                 vreg_l24a_3p075: ldo24 {
 301                         regulator-min-microvolt = <3088000>;
 302                         regulator-max-microvolt = <3088000>;
 303                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 304                 };
 305
 306                 vreg_l25a_3p3: ldo25 {
 307                         regulator-min-microvolt = <3300000>;
 308                         regulator-max-microvolt = <3312000>;
 309                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 310                 };
 311
 312                 vreg_l26a_1p2: ldo26 {
 313                         regulator-min-microvolt = <1200000>;
 314                         regulator-max-microvolt = <1200000>;
 315                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 316                 };
 317
 318                 vreg_lvs1a_1p8: lvs1 {
 319                         regulator-min-microvolt = <1800000>;
 320                         regulator-max-microvolt = <1800000>;
 321                         regulator-always-on;
 322                 };
 323
 324                 vreg_lvs2a_1p8: lvs2 {
 325                         regulator-min-microvolt = <1800000>;
 326                         regulator-max-microvolt = <1800000>;
 327                         regulator-always-on;
 328                 };
 329         };
 330
 331         pmi8998-rpmh-regulators {
 332                 compatible = "qcom,pmi8998-rpmh-regulators";
 333                 qcom,pmic-id = "b";
 334
 335                 vdd-bob-supply = <&vph_pwr>;
 336
 337                 vreg_bob: bob {
 338                         regulator-min-microvolt = <3312000>;
 339                         regulator-max-microvolt = <3600000>;
 340                         regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
 341                         regulator-allow-bypass;
 342                 };
 343         };
 344 };
 345
 346 &cdsp_pas {
 347         status = "okay";
 348         firmware-name = "qcom/sdm845/cdsp.mdt";
 349 };
 350
 351 &gcc {
 352         protected-clocks = <GCC_QSPI_CORE_CLK>,
 353                            <GCC_QSPI_CORE_CLK_SRC>,
 354                            <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
 355 };
 356
 357 &gpu {
 358         zap-shader {
 359                 memory-region = <&gpu_mem>;
 360                 firmware-name = "qcom/sdm845/a630_zap.mbn";
 361         };
 362 };
 363
 364 &i2c11 {
 365         /* On Low speed expansion */
 366         label = "LS-I2C1";
 367         status = "okay";
 368 };
 369
 370 &i2c14 {
 371         /* On Low speed expansion */
 372         label = "LS-I2C0";
 373         status = "okay";
 374 };
 375
 376 &mss_pil {
 377         status = "okay";
 378         firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mbn";
 379 };
 380
 381 &pcie0 {
 382         status = "okay";
 383         perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
 384         enable-gpio = <&tlmm 134 GPIO_ACTIVE_HIGH>;
 385
 386         vddpe-3v3-supply = <&pcie0_3p3v_dual>;
 387
 388         pinctrl-names = "default";
 389         pinctrl-0 = <&pcie0_default_state>;
 390 };
 391
 392 &pcie0_phy {
 393         status = "okay";
 394
 395         vdda-phy-supply = <&vreg_l1a_0p875>;
 396         vdda-pll-supply = <&vreg_l26a_1p2>;
 397 };
 398
 399 &pcie1 {
 400         status = "okay";
 401         perst-gpio = <&tlmm 102 GPIO_ACTIVE_LOW>;
 402
 403         pinctrl-names = "default";
 404         pinctrl-0 = <&pcie1_default_state>;
 405 };
 406
 407 &pcie1_phy {
 408         status = "okay";
 409
 410         vdda-phy-supply = <&vreg_l1a_0p875>;
 411         vdda-pll-supply = <&vreg_l26a_1p2>;
 412 };
 413
 414 &pm8998_gpio {
 415         vol_up_pin_a: vol-up-active {
 416                 pins = "gpio6";
 417                 function = "normal";
 418                 input-enable;
 419                 bias-pull-up;
 420                 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 421         };
 422 };
 423
 424 &pm8998_pon {
 425         resin {
 426                 compatible = "qcom,pm8941-resin";
 427                 interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
 428                 debounce = <15625>;
 429                 bias-pull-up;
 430                 linux,code = <KEY_VOLUMEDOWN>;
 431         };
 432 };
 433
 434 /* QUAT I2S Uses 4 I2S SD Lines for audio on LT9611 HDMI Bridge */
 435 &q6afedai {
 436         qi2s@22 {
 437                 reg = <22>;
 438                 qcom,sd-lines = <0 1 2 3>;
 439         };
 440 };
 441
 442 &q6asmdai {
 443         dai@0 {
 444                 reg = <0>;
 445         };
 446
 447         dai@1 {
 448                 reg = <1>;
 449         };
 450
 451         dai@2 {
 452                 reg = <2>;
 453         };
 454
 455         dai@3 {
 456                 reg = <3>;
 457                 direction = <2>;
 458                 is-compress-dai;
 459         };
 460 };
 461
 462 &qupv3_id_0 {
 463         status = "okay";
 464 };
 465
 466 &qupv3_id_1 {
 467         status = "okay";
 468 };
 469
 470 &sdhc_2 {
 471         status = "okay";
 472
 473         pinctrl-names = "default";
 474         pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
 475
 476         vmmc-supply = <&vreg_l21a_2p95>;
 477         vqmmc-supply = <&vreg_l13a_2p95>;
 478
 479         bus-width = <4>;
 480         cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>;
 481 };
 482
 483 &sound {
 484         compatible = "qcom,db845c-sndcard";
 485         pinctrl-0 = <&quat_mi2s_active
 486                          &quat_mi2s_sd0_active
 487                          &quat_mi2s_sd1_active
 488                          &quat_mi2s_sd2_active
 489                          &quat_mi2s_sd3_active>;
 490         pinctrl-names = "default";
 491         model = "DB845c";
 492         audio-routing =
 493                 "RX_BIAS", "MCLK",
 494                 "AMIC1", "MIC BIAS1",
 495                 "AMIC2", "MIC BIAS2",
 496                 "DMIC0", "MIC BIAS1",
 497                 "DMIC1", "MIC BIAS1",
 498                 "DMIC2", "MIC BIAS3",
 499                 "DMIC3", "MIC BIAS3",
 500                 "SpkrLeft IN", "SPK1 OUT",
 501                 "SpkrRight IN", "SPK2 OUT",
 502                 "MM_DL1",  "MultiMedia1 Playback",
 503                 "MM_DL2",  "MultiMedia2 Playback",
 504                 "MM_DL4",  "MultiMedia4 Playback",
 505                 "MultiMedia3 Capture", "MM_UL3";
 506
 507         mm1-dai-link {
 508                 link-name = "MultiMedia1";
 509                 cpu {
 510                         sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA1>;
 511                 };
 512         };
 513
 514         mm2-dai-link {
 515                 link-name = "MultiMedia2";
 516                 cpu {
 517                         sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA2>;
 518                 };
 519         };
 520
 521         mm3-dai-link {
 522                 link-name = "MultiMedia3";
 523                 cpu {
 524                         sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA3>;
 525                 };
 526         };
 527
 528         mm4-dai-link {
 529                 link-name = "MultiMedia4";
 530                 cpu {
 531                         sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA4>;
 532                 };
 533         };
 534
 535         slim-dai-link {
 536                 link-name = "SLIM Playback";
 537                 cpu {
 538                         sound-dai = <&q6afedai SLIMBUS_0_RX>;
 539                 };
 540
 541                 platform {
 542                         sound-dai = <&q6routing>;
 543                 };
 544
 545                 codec {
 546                         sound-dai =  <&left_spkr>, <&right_spkr>, <&swm 0>, <&wcd9340 0>;
 547                 };
 548         };
 549
 550         slimcap-dai-link {
 551                 link-name = "SLIM Capture";
 552                 cpu {
 553                         sound-dai = <&q6afedai SLIMBUS_0_TX>;
 554                 };
 555
 556                 platform {
 557                         sound-dai = <&q6routing>;
 558                 };
 559
 560                 codec {
 561                         sound-dai = <&wcd9340 1>;
 562                 };
 563         };
 564 };
 565
 566 &spi2 {
 567         /* On Low speed expansion */
 568         label = "LS-SPI0";
 569         status = "okay";
 570 };
 571
 572 &tlmm {
 573         pcie0_default_state: pcie0-default {
 574                 clkreq {
 575                         pins = "gpio36";
 576                         function = "pci_e0";
 577                         bias-pull-up;
 578                 };
 579
 580                 reset-n {
 581                         pins = "gpio35";
 582                         function = "gpio";
 583
 584                         drive-strength = <2>;
 585                         output-low;
 586                         bias-pull-down;
 587                 };
 588
 589                 wake-n {
 590                         pins = "gpio37";
 591                         function = "gpio";
 592
 593                         drive-strength = <2>;
 594                         bias-pull-up;
 595                 };
 596         };
 597
 598         pcie0_pwren_state: pcie0-pwren {
 599                 pins = "gpio90";
 600                 function = "gpio";
 601
 602                 drive-strength = <2>;
 603                 bias-disable;
 604         };
 605
 606         pcie1_default_state: pcie1-default {
 607                 perst-n {
 608                         pins = "gpio102";
 609                         function = "gpio";
 610
 611                         drive-strength = <16>;
 612                         bias-disable;
 613                 };
 614
 615                 clkreq {
 616                         pins = "gpio103";
 617                         function = "pci_e1";
 618                         bias-pull-up;
 619                 };
 620
 621                 wake-n {
 622                         pins = "gpio11";
 623                         function = "gpio";
 624
 625                         drive-strength = <2>;
 626                         bias-pull-up;
 627                 };
 628
 629                 reset-n {
 630                         pins = "gpio75";
 631                         function = "gpio";
 632
 633                         drive-strength = <16>;
 634                         bias-pull-up;
 635                         output-high;
 636                 };
 637         };
 638
 639         sdc2_default_state: sdc2-default {
 640                 clk {
 641                         pins = "sdc2_clk";
 642                         bias-disable;
 643
 644                         /*
 645                          * It seems that mmc_test reports errors if drive
 646                          * strength is not 16 on clk, cmd, and data pins.
 647                          */
 648                         drive-strength = <16>;
 649                 };
 650
 651                 cmd {
 652                         pins = "sdc2_cmd";
 653                         bias-pull-up;
 654                         drive-strength = <10>;
 655                 };
 656
 657                 data {
 658                         pins = "sdc2_data";
 659                         bias-pull-up;
 660                         drive-strength = <10>;
 661                 };
 662         };
 663
 664         sdc2_card_det_n: sd-card-det-n {
 665                 pins = "gpio126";
 666                 function = "gpio";
 667                 bias-pull-up;
 668         };
 669
 670         wcd_intr_default: wcd_intr_default {
 671                 pins = <54>;
 672                 function = "gpio";
 673
 674                 input-enable;
 675                 bias-pull-down;
 676                 drive-strength = <2>;
 677         };
 678 };
 679
 680 &uart3 {
 681         label = "LS-UART0";
 682         status = "disabled";
 683 };
 684
 685 &uart6 {
 686         status = "okay";
 687
 688         bluetooth {
 689                 compatible = "qcom,wcn3990-bt";
 690
 691                 vddio-supply = <&vreg_s4a_1p8>;
 692                 vddxo-supply = <&vreg_l7a_1p8>;
 693                 vddrf-supply = <&vreg_l17a_1p3>;
 694                 vddch0-supply = <&vreg_l25a_3p3>;
 695                 max-speed = <3200000>;
 696         };
 697 };
 698
 699 &uart9 {
 700         label = "LS-UART1";
 701         status = "okay";
 702 };
 703
 704 &usb_1 {
 705         status = "okay";
 706 };
 707
 708 &usb_1_dwc3 {
 709         dr_mode = "peripheral";
 710 };
 711
 712 &usb_1_hsphy {
 713         status = "okay";
 714
 715         vdd-supply = <&vreg_l1a_0p875>;
 716         vdda-pll-supply = <&vreg_l12a_1p8>;
 717         vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
 718
 719         qcom,imp-res-offset-value = <8>;
 720         qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
 721         qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
 722         qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
 723 };
 724
 725 &usb_1_qmpphy {
 726         status = "okay";
 727
 728         vdda-phy-supply = <&vreg_l26a_1p2>;
 729         vdda-pll-supply = <&vreg_l1a_0p875>;
 730 };
 731
 732 &usb_2 {
 733         status = "okay";
 734 };
 735
 736 &usb_2_dwc3 {
 737         dr_mode = "host";
 738 };
 739
 740 &usb_2_hsphy {
 741         status = "okay";
 742
 743         vdd-supply = <&vreg_l1a_0p875>;
 744         vdda-pll-supply = <&vreg_l12a_1p8>;
 745         vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
 746
 747         qcom,imp-res-offset-value = <8>;
 748         qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>;
 749 };
 750
 751 &usb_2_qmpphy {
 752         status = "okay";
 753
 754         vdda-phy-supply = <&vreg_l26a_1p2>;
 755         vdda-pll-supply = <&vreg_l1a_0p875>;
 756 };
 757
 758 &ufs_mem_hc {
 759         status = "okay";
 760
 761         reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
 762
 763         vcc-supply = <&vreg_l20a_2p95>;
 764         vcc-max-microamp = <800000>;
 765 };
 766
 767 &ufs_mem_phy {
 768         status = "okay";
 769
 770         vdda-phy-supply = <&vreg_l1a_0p875>;
 771         vdda-pll-supply = <&vreg_l26a_1p2>;
 772 };
 773
 774 &wcd9340{
 775         pinctrl-0 = <&wcd_intr_default>;
 776         pinctrl-names = "default";
 777         clock-names = "extclk";
 778         clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
 779         reset-gpios = <&tlmm 64 0>;
 780         vdd-buck-supply = <&vreg_s4a_1p8>;
 781         vdd-buck-sido-supply = <&vreg_s4a_1p8>;
 782         vdd-tx-supply = <&vreg_s4a_1p8>;
 783         vdd-rx-supply = <&vreg_s4a_1p8>;
 784         vdd-io-supply = <&vreg_s4a_1p8>;
 785
 786         swm: swm@c85 {
 787                 left_spkr: wsa8810-left{
 788                         compatible = "sdw10217201000";
 789                         reg = <0 1>;
 790                         powerdown-gpios = <&wcdgpio 2 GPIO_ACTIVE_HIGH>;
 791                         #thermal-sensor-cells = <0>;
 792                         sound-name-prefix = "SpkrLeft";
 793                         #sound-dai-cells = <0>;
 794                 };
 795
 796                 right_spkr: wsa8810-right{
 797                         compatible = "sdw10217201000";
 798                         powerdown-gpios = <&wcdgpio 2 GPIO_ACTIVE_HIGH>;
 799                         reg = <0 2>;
 800                         #thermal-sensor-cells = <0>;
 801                         sound-name-prefix = "SpkrRight";
 802                         #sound-dai-cells = <0>;
 803                 };
 804         };
 805 };
 806
 807 &wifi {
 808         status = "okay";
 809
 810         vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
 811         vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
 812         vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
 813         vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
 814
 815         qcom,snoc-host-cap-8bit-quirk;
 816 };
 817
 818 /* PINCTRL - additions to nodes defined in sdm845.dtsi */
 819 &qup_spi2_default {
 820         drive-strength = <16>;
 821 };
 822
 823 &qup_uart3_default{
 824         pinmux {
 825                 pins = "gpio41", "gpio42", "gpio43", "gpio44";
 826                 function = "qup3";
 827         };
 828 };
 829
 830 &qup_uart6_default {
 831         pinmux {
 832                 pins = "gpio45", "gpio46", "gpio47", "gpio48";
 833                 function = "qup6";
 834         };
 835
 836         cts {
 837                 pins = "gpio45";
 838                 bias-disable;
 839         };
 840
 841         rts-tx {
 842                 pins = "gpio46", "gpio47";
 843                 drive-strength = <2>;
 844                 bias-disable;
 845         };
 846
 847         rx {
 848                 pins = "gpio48";
 849                 bias-pull-up;
 850         };
 851 };
 852
 853 &qup_uart9_default {
 854         pinconf-tx {
 855                 pins = "gpio4";
 856                 drive-strength = <2>;
 857                 bias-disable;
 858         };
 859
 860         pinconf-rx {
 861                 pins = "gpio5";
 862                 drive-strength = <2>;
 863                 bias-pull-up;
 864         };
 865 };