arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Copyright (C) 2022 PHYTEC Messtechnik GmbH
   4  * Author: Teresa Remmet <t.remmet@phytec.de>
   5  */
   6
   7 /dts-v1/;
   8
   9 #include <dt-bindings/interrupt-controller/irq.h>
  10 #include <dt-bindings/leds/common.h>
  11 #include <dt-bindings/phy/phy-imx8-pcie.h>
  12 #include "imx8mm-phycore-som.dtsi"
  13
  14 / {
  15         model = "PHYTEC phyBOARD-Polis-i.MX8MM RDK";
  16         compatible = "phytec,imx8mm-phyboard-polis-rdk",
  17                      "phytec,imx8mm-phycore-som", "fsl,imx8mm";
  18
  19         chosen {
  20                 stdout-path = &uart3;
  21         };
  22
  23         bt_osc_32k: bt-lp-clock {
  24                 compatible = "fixed-clock";
  25                 clock-frequency = <32768>;
  26                 clock-output-names = "bt_osc_32k";
  27                 #clock-cells = <0>;
  28         };
  29
  30         can_osc_40m: can-clock {
  31                 compatible = "fixed-clock";
  32                 clock-frequency = <40000000>;
  33                 clock-output-names = "can_osc_40m";
  34                 #clock-cells = <0>;
  35         };
  36
  37         fan {
  38                 compatible = "gpio-fan";
  39                 gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
  40                 gpio-fan,speed-map = <0     0
  41                                       13000 1>;
  42                 pinctrl-names = "default";
  43                 pinctrl-0 = <&pinctrl_fan>;
  44                 #cooling-cells = <2>;
  45         };
  46
  47         leds {
  48                 compatible = "gpio-leds";
  49                 pinctrl-names = "default";
  50                 pinctrl-0 = <&pinctrl_leds>;
  51
  52                 led-0 {
  53                         color = <LED_COLOR_ID_RED>;
  54                         function = LED_FUNCTION_DISK;
  55                         gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
  56                         linux,default-trigger = "mmc2";
  57                 };
  58
  59                 led-1 {
  60                         color = <LED_COLOR_ID_BLUE>;
  61                         function = LED_FUNCTION_DISK;
  62                         gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
  63                         linux,default-trigger = "mmc1";
  64                 };
  65
  66                 led-2 {
  67                         color = <LED_COLOR_ID_GREEN>;
  68                         function = LED_FUNCTION_CPU;
  69                         gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
  70                         linux,default-trigger = "heartbeat";
  71                 };
  72         };
  73
  74         usdhc1_pwrseq: pwr-seq {
  75                 compatible = "mmc-pwrseq-simple";
  76                 post-power-on-delay-ms = <100>;
  77                 power-off-delay-us = <60>;
  78                 reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
  79         };
  80
  81         reg_can_en: regulator-can-en {
  82                 compatible = "regulator-fixed";
  83                 gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
  84                 pinctrl-names = "default";
  85                 pinctrl-0 = <&pinctrl_can_en>;
  86                 regulator-max-microvolt = <3300000>;
  87                 regulator-min-microvolt = <3300000>;
  88                 regulator-name = "CAN_EN";
  89                 startup-delay-us = <20>;
  90         };
  91
  92         reg_usb_otg1_vbus: regulator-usb-otg1 {
  93                 compatible = "regulator-fixed";
  94                 gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
  95                 enable-active-high;
  96                 pinctrl-names = "default";
  97                 pinctrl-0 = <&pinctrl_usbotg1pwrgrp>;
  98                 regulator-name = "usb_otg1_vbus";
  99                 regulator-max-microvolt = <5000000>;
 100                 regulator-min-microvolt = <5000000>;
 101         };
 102
 103         reg_usdhc2_vmmc: regulator-usdhc2 {
 104                 compatible = "regulator-fixed";
 105                 gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
 106                 enable-active-high;
 107                 off-on-delay-us = <20000>;
 108                 pinctrl-names = "default";
 109                 pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
 110                 regulator-max-microvolt = <3300000>;
 111                 regulator-min-microvolt = <3300000>;
 112                 regulator-name = "VSD_3V3";
 113         };
 114
 115         reg_vcc_3v3: regulator-vcc-3v3 {
 116                 compatible = "regulator-fixed";
 117                 regulator-max-microvolt = <3300000>;
 118                 regulator-min-microvolt = <3300000>;
 119                 regulator-name = "VCC_3V3";
 120         };
 121 };
 122
 123 /* SPI - CAN MCP251XFD */
 124 &ecspi1 {
 125         cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
 126         pinctrl-names = "default";
 127         pinctrl-0 = <&pinctrl_ecspi1>;
 128         status = "okay";
 129
 130         can0: can@0 {
 131                 compatible = "microchip,mcp251xfd";
 132                 clocks = <&can_osc_40m>;
 133                 interrupt-parent = <&gpio1>;
 134                 interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
 135                 pinctrl-names = "default";
 136                 pinctrl-0 = <&pinctrl_can_int>;
 137                 reg = <0>;
 138                 spi-max-frequency = <20000000>;
 139                 xceiver-supply = <&reg_can_en>;
 140         };
 141 };
 142
 143 &gpio1 {
 144         gpio-line-names = "nINT_ETHPHY", "LED_RED", "WDOG_INT", "X_RTC_INT",
 145                 "", "", "", "RESET_ETHPHY",
 146                 "CAN_nINT", "CAN_EN", "nENABLE_FLATLINK", "",
 147                 "USB_OTG_VBUS_EN", "", "LED_GREEN", "LED_BLUE";
 148 };
 149
 150 &gpio2 {
 151         gpio-line-names = "", "", "", "",
 152                 "", "", "BT_REG_ON", "WL_REG_ON",
 153                 "BT_DEV_WAKE", "BT_HOST_WAKE", "", "",
 154                 "X_SD2_CD_B", "", "", "",
 155                 "", "", "", "SD2_RESET_B";
 156 };
 157
 158 &gpio4 {
 159         gpio-line-names = "", "", "", "",
 160                 "", "", "", "",
 161                 "FAN", "miniPCIe_nPERST", "", "",
 162                 "COEX1", "COEX2";
 163 };
 164
 165 &gpio5 {
 166         gpio-line-names = "", "", "", "",
 167                 "", "", "", "",
 168                 "", "ECSPI1_SS0";
 169 };
 170
 171 &i2c4 {
 172         clock-frequency = <400000>;
 173         pinctrl-names = "default";
 174         pinctrl-0 = <&pinctrl_i2c4>;
 175 };
 176
 177 /* PCIe */
 178 &pcie0 {
 179         assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
 180                           <&clk IMX8MM_CLK_PCIE1_CTRL>;
 181         assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
 182                                  <&clk IMX8MM_SYS_PLL2_250M>;
 183         assigned-clock-rates = <10000000>, <250000000>;
 184         pinctrl-names = "default";
 185         pinctrl-0 = <&pinctrl_pcie>;
 186         reset-gpio = <&gpio4 9 GPIO_ACTIVE_LOW>;
 187         status = "okay";
 188 };
 189
 190 &pcie_phy {
 191         clocks = <&clk IMX8MM_CLK_PCIE1_PHY>;
 192         fsl,clkreq-unsupported;
 193         fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_OUTPUT>;
 194         fsl,tx-deemph-gen1 = <0x2d>;
 195         fsl,tx-deemph-gen2 = <0xf>;
 196         status = "okay";
 197 };
 198
 199 &rv3028 {
 200         trickle-resistor-ohms = <3000>;
 201 };
 202
 203 &snvs_pwrkey {
 204         status = "okay";
 205 };
 206
 207 /* UART - RS232/RS485 */
 208 &uart1 {
 209         assigned-clocks = <&clk IMX8MM_CLK_UART1>;
 210         assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
 211         pinctrl-names = "default";
 212         pinctrl-0 = <&pinctrl_uart1>;
 213         uart-has-rtscts;
 214         status = "okay";
 215 };
 216
 217 /* UART - Sterling-LWB Bluetooth */
 218 &uart2 {
 219         assigned-clocks = <&clk IMX8MM_CLK_UART2>;
 220         assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
 221         fsl,dte-mode;
 222         pinctrl-names = "default";
 223         pinctrl-0 = <&pinctrl_uart2_bt>;
 224         uart-has-rtscts;
 225         status = "okay";
 226
 227         bluetooth {
 228                 compatible = "brcm,bcm43438-bt";
 229                 clocks = <&bt_osc_32k>;
 230                 clock-names = "lpo";
 231                 device-wakeup-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
 232                 interrupt-names = "host-wakeup";
 233                 interrupt-parent = <&gpio2>;
 234                 interrupts = <9 IRQ_TYPE_EDGE_BOTH>;
 235                 max-speed = <2000000>;
 236                 pinctrl-names = "default";
 237                 pinctrl-0 = <&pinctrl_bt>;
 238                 shutdown-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
 239                 vddio-supply = <&reg_vcc_3v3>;
 240         };
 241 };
 242
 243 /* UART - console */
 244 &uart3 {
 245         pinctrl-names = "default";
 246         pinctrl-0 = <&pinctrl_uart3>;
 247         status = "okay";
 248 };
 249
 250 /* USB */
 251 &usbotg1 {
 252         adp-disable;
 253         dr_mode = "otg";
 254         over-current-active-low;
 255         samsung,picophy-pre-emp-curr-control = <3>;
 256         samsung,picophy-dc-vol-level-adjust = <7>;
 257         srp-disable;
 258         vbus-supply = <&reg_usb_otg1_vbus>;
 259         status = "okay";
 260 };
 261
 262 &usbotg2 {
 263         disable-over-current;
 264         dr_mode = "host";
 265         samsung,picophy-pre-emp-curr-control = <3>;
 266         samsung,picophy-dc-vol-level-adjust = <7>;
 267         status = "okay";
 268 };
 269
 270 /* SDIO - Sterling-LWB Wifi */
 271 &usdhc1 {
 272         assigned-clocks = <&clk IMX8MM_CLK_USDHC1>;
 273         assigned-clock-rates = <200000000>;
 274         bus-width = <4>;
 275         mmc-pwrseq = <&usdhc1_pwrseq>;
 276         non-removable;
 277         no-1-8-v;
 278         pinctrl-names = "default";
 279         pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_wlan>;
 280         #address-cells = <1>;
 281         #size-cells = <0>;
 282         status = "okay";
 283
 284         brcmf: wifi@1 {
 285                 compatible = "brcm,bcm4329-fmac";
 286                 reg = <1>;
 287         };
 288 };
 289
 290 /* SD-Card */
 291 &usdhc2 {
 292         assigned-clocks = <&clk IMX8MM_CLK_USDHC2>;
 293         assigned-clock-rates = <200000000>;
 294         bus-width = <4>;
 295         cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
 296         disable-wp;
 297         pinctrl-names = "default", "state_100mhz", "state_200mhz";
 298         pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
 299         pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
 300         pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
 301         vmmc-supply = <&reg_usdhc2_vmmc>;
 302         vqmmc-supply = <&reg_nvcc_sd2>;
 303         status = "okay";
 304 };
 305
 306 &iomuxc {
 307         pinctrl_bt: btgrp {
 308                 fsl,pins = <
 309                         MX8MM_IOMUXC_SD1_DATA4_GPIO2_IO6        0x00
 310                         MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8        0x00
 311                         MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9        0x00
 312                 >;
 313         };
 314
 315         pinctrl_can_en: can-engrp {
 316                 fsl,pins = <
 317                         MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9       0x00
 318                 >;
 319         };
 320
 321         pinctrl_can_int: can-intgrp {
 322                 fsl,pins = <
 323                         MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8       0x00
 324                 >;
 325         };
 326
 327         pinctrl_ecspi1: ecspi1grp {
 328                 fsl,pins = <
 329                         MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO    0x80
 330                         MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI    0x80
 331                         MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK    0x80
 332                         MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9       0x00
 333                 >;
 334         };
 335
 336         pinctrl_fan: fan0grp {
 337                 fsl,pins = <
 338                         MX8MM_IOMUXC_SAI1_RXD6_GPIO4_IO8        0x16
 339                 >;
 340         };
 341
 342         pinctrl_i2c4: i2c4grp {
 343                 fsl,pins = <
 344                         MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL          0x400001c2
 345                         MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA          0x400001c2
 346                 >;
 347         };
 348
 349         pinctrl_leds: leds1grp {
 350                 fsl,pins = <
 351                         MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1       0x16
 352                         MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14      0x16
 353                         MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15      0x16
 354                 >;
 355         };
 356
 357         pinctrl_pcie: pciegrp {
 358                 fsl,pins = <
 359                         MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9        0x00
 360                         MX8MM_IOMUXC_SAI1_TXD0_GPIO4_IO12       0x12
 361                         MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19       0x12
 362                 >;
 363         };
 364
 365         pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
 366                 fsl,pins = <
 367                         MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19     0x40
 368                 >;
 369         };
 370
 371         pinctrl_uart1: uart1grp {
 372                 fsl,pins = <
 373                         MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX      0x00
 374                         MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B  0x00
 375                         MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX     0x00
 376                         MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B  0x00
 377                 >;
 378         };
 379
 380         pinctrl_uart2_bt: uart2btgrp {
 381                 fsl,pins = <
 382                         MX8MM_IOMUXC_SAI3_RXC_UART2_DTE_RTS_B   0x00
 383                         MX8MM_IOMUXC_SAI3_RXD_UART2_DTE_CTS_B   0x00
 384                         MX8MM_IOMUXC_SAI3_TXC_UART2_DTE_RX      0x00
 385                         MX8MM_IOMUXC_SAI3_TXFS_UART2_DTE_TX     0x00
 386                 >;
 387         };
 388
 389         pinctrl_uart3: uart3grp {
 390                 fsl,pins = <
 391                         MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX     0x40
 392                         MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX     0x40
 393                 >;
 394         };
 395
 396         pinctrl_usbotg1pwrgrp: usbotg1pwrgrp {
 397                 fsl,pins = <
 398                         MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12      0x00
 399                 >;
 400         };
 401
 402         pinctrl_usdhc1: usdhc1grp {
 403                 fsl,pins = <
 404                         MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK         0x182
 405                         MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD         0xc6
 406                         MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0     0xc6
 407                         MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1     0xc6
 408                         MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2     0xc6
 409                         MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3     0xc6
 410                 >;
 411         };
 412
 413         pinctrl_usdhc2_gpio: usdhc2gpiogrp {
 414                 fsl,pins = <
 415                         MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12        0x40
 416                 >;
 417         };
 418
 419         pinctrl_usdhc2: usdhc2grp {
 420                 fsl,pins = <
 421                         MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT  0x1d0
 422                         MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK         0x192
 423                         MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD         0x1d2
 424                         MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0     0x1d2
 425                         MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1     0x1d2
 426                         MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2     0x1d2
 427                         MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3     0x1d2
 428                 >;
 429         };
 430
 431         pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 432                 fsl,pins = <
 433                         MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT  0x1d0
 434                         MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK         0x194
 435                         MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD         0x1d4
 436                         MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0     0x1d4
 437                         MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1     0x1d4
 438                         MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2     0x1d4
 439                         MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3     0x1d4
 440                 >;
 441         };
 442
 443         pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 444                 fsl,pins = <
 445                         MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT  0x1d0
 446                         MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK         0x196
 447                         MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD         0x1d6
 448                         MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0     0x1d6
 449                         MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1     0x1d6
 450                         MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2     0x1d6
 451                         MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3     0x1d6
 452                 >;
 453         };
 454
 455         pinctrl_wlan: wlangrp {
 456                 fsl,pins = <
 457                         MX8MM_IOMUXC_SD1_DATA5_GPIO2_IO7        0x00
 458                 >;
 459         };
 460 };