1 /* SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause) */
3 * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
4 * Copyright (C) 2020 Ahmad Fatoum, Pengutronix
9 #include "stm32mp157.dtsi"
10 #include "stm32mp15xx-osd32.dtsi"
11 #include "stm32mp15xxac-pinctrl.dtsi"
13 #include <dt-bindings/gpio/gpio.h>
14 #include <dt-bindings/pwm/pwm.h>
17 model = "Linux Automation MC-1 board";
18 compatible = "lxa,stm32mp157c-mc1", "st,stm32mp157";
21 ethernet0 = ðernet0;
27 backlight: backlight {
28 compatible = "pwm-backlight";
29 pwms = <&backlight_pwm 1 100000 PWM_POLARITY_INVERTED>;
30 brightness-levels = <0 31 63 95 127 159 191 223 255>;
31 default-brightness-level = <7>;
32 power-supply = <®_5v2>; /* 3V3_BACKLIGHT */
40 compatible = "gpio-leds";
43 label = "mc1:green:act";
44 gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
45 linux,default-trigger = "heartbeat";
50 compatible = "pwm-leds";
53 label = "mc1:red:rgb";
54 pwms = <&leds_pwm 1 1000000 0>;
55 max-brightness = <255>;
60 label = "mc1:green:rgb";
61 pwms = <&leds_pwm 2 1000000 0>;
62 max-brightness = <255>;
67 label = "mc1:blue:rgb";
68 pwms = <&leds_pwm 3 1000000 0>;
69 max-brightness = <255>;
75 compatible = "edt,etm0700g0edh6", "simple-panel";
76 backlight = <&backlight>;
77 enable-gpios = <&gpiod 4 GPIO_ACTIVE_HIGH>;
78 power-supply = <®_3v3>;
81 panel_input: endpoint {
82 remote-endpoint = <<dc_ep0_out>;
87 reg_3v3: regulator_3v3 {
88 compatible = "regulator-fixed";
89 regulator-name = "3V3";
90 regulator-min-microvolt = <3300000>;
91 regulator-max-microvolt = <3300000>;
96 /* supplied by either debug board or PoE */
97 reg_5v2: regulator_5v2 {
98 compatible = "regulator-fixed";
99 regulator-name = "5V2";
100 regulator-min-microvolt = <5200000>;
101 regulator-max-microvolt = <5200000>;
107 pinctrl-names = "default", "sleep";
108 pinctrl-0 = <ðernet0_rgmii_pins_b>;
109 pinctrl-1 = <ðernet0_rgmii_sleep_pins_b>;
110 phy-mode = "rgmii-id";
111 phy-handle = <ðphy>;
115 compatible = "snps,dwmac-mdio";
116 #address-cells = <1>;
119 ethphy: ethernet-phy@3 { /* KSZ9031RN */
121 reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */
122 interrupt-parent = <&gpioa>;
123 interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* ETH_MDINT# */
124 rxc-skew-ps = <1860>;
125 txc-skew-ps = <1860>;
126 reset-assert-us = <10000>;
127 reset-deassert-us = <300>;
134 gpio-line-names = "HWID0", "HWID1", "HWID2", "HWID3", "", "",
139 pinctrl-names = "default", "sleep";
140 pinctrl-0 = <&i2c5_pins_b>;
141 pinctrl-1 = <&i2c5_sleep_pins_b>;
142 clock-frequency = <400000>;
146 compatible = "edt,edt-ft5x06";
147 interrupt-parent = <&gpiod>;
148 interrupts = <11 IRQ_TYPE_EDGE_FALLING>; /* TOUCH_INT# */
149 vcc-supply = <®_3v3>;
151 reset-gpios = <&gpiof 8 GPIO_ACTIVE_LOW>; /* TOUCH_RESET# */
152 touchscreen-size-x = <1792>;
153 touchscreen-size-y = <1024>;
159 pinctrl-names = "default", "sleep";
160 pinctrl-0 = <<dc_pins_c>;
161 pinctrl-1 = <<dc_sleep_pins_c>;
165 ltdc_ep0_out: endpoint@0 {
167 remote-endpoint = <&panel_input>;
174 buck4-supply = <®_5v2>; /* VIN */
175 ldo2-supply = <®_5v2>; /* PMIC_LDO25IN */
176 ldo5-supply = <®_5v2>; /* PMIC_LDO25IN */
177 boost-supply = <®_5v2>; /* PMIC_BSTIN */
178 pwr_sw2-supply = <&bst_out>; /* PMIC_SWIN */
183 pinctrl-names = "default", "opendrain", "sleep";
184 pinctrl-0 = <&sdmmc1_b4_pins_a>;
185 pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
186 pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
188 cd-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
192 vmmc-supply = <®_3v3>;
198 * board lacks external pull-ups on SDMMC lines. Class 10 SD refuses to
199 * work, thus enable internal pull-ups.
202 /delete-property/ bias-disable;
206 /delete-property/ bias-disable;
212 pinctrl-names = "default", "opendrain", "sleep";
213 pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
214 pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
215 pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
222 vmmc-supply = <®_3v3>;
230 pinctrl-names = "default", "sleep";
231 pinctrl-0 = <&pwm3_pins_b>;
232 pinctrl-1 = <&pwm3_sleep_pins_b>;
241 pinctrl-names = "default", "sleep";
242 pinctrl-0 = <&pwm5_pins_b>;
243 pinctrl-1 = <&pwm5_sleep_pins_b>;
249 pinctrl-names = "default";
250 pinctrl-0 = <&uart4_pins_a>;