1 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
3 * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
4 * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
8 #include "stm32mp157c-ed1.dts"
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/input/input.h>
13 model = "STMicroelectronics STM32MP157C eval daughter on eval mother";
14 compatible = "st,stm32mp157c-ev1", "st,stm32mp157c-ed1", "st,stm32mp157";
17 stdout-path = "serial0:115200n8";
22 ethernet0 = ðernet0;
26 clk_ext_camera: clk-ext-camera {
28 compatible = "fixed-clock";
29 clock-frequency = <24000000>;
34 compatible = "gpio-keys";
35 pinctrl-0 = <&joystick_pins>;
36 pinctrl-names = "default";
39 linux,code = <KEY_ENTER>;
40 interrupt-parent = <&stmfx_pinctrl>;
41 interrupts = <0 IRQ_TYPE_EDGE_RISING>;
45 linux,code = <KEY_DOWN>;
46 interrupt-parent = <&stmfx_pinctrl>;
47 interrupts = <1 IRQ_TYPE_EDGE_RISING>;
51 linux,code = <KEY_LEFT>;
52 interrupt-parent = <&stmfx_pinctrl>;
53 interrupts = <2 IRQ_TYPE_EDGE_RISING>;
57 linux,code = <KEY_RIGHT>;
58 interrupt-parent = <&stmfx_pinctrl>;
59 interrupts = <3 IRQ_TYPE_EDGE_RISING>;
63 linux,code = <KEY_UP>;
64 interrupt-parent = <&stmfx_pinctrl>;
65 interrupts = <4 IRQ_TYPE_EDGE_RISING>;
69 panel_backlight: panel-backlight {
70 compatible = "gpio-backlight";
71 gpios = <&gpiod 13 GPIO_ACTIVE_LOW>;
78 pinctrl-names = "default";
79 pinctrl-0 = <&cec_pins_a>;
85 pinctrl-names = "default", "sleep";
86 pinctrl-0 = <&dcmi_pins_a>;
87 pinctrl-1 = <&dcmi_sleep_pins_a>;
91 remote-endpoint = <&ov5640_0>;
101 #address-cells = <1>;
103 phy-dsi-supply = <®18>;
107 #address-cells = <1>;
113 remote-endpoint = <<dc_ep0_out>;
120 remote-endpoint = <&dsi_panel_in>;
126 compatible = "raydium,rm68200";
128 reset-gpios = <&gpiof 15 GPIO_ACTIVE_LOW>;
129 backlight = <&panel_backlight>;
130 power-supply = <&v3v3>;
134 dsi_panel_in: endpoint {
135 remote-endpoint = <&dsi_out>;
143 pinctrl-0 = <ðernet0_rgmii_pins_a>;
144 pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
145 pinctrl-names = "default", "sleep";
146 phy-mode = "rgmii-id";
148 phy-handle = <&phy0>;
151 #address-cells = <1>;
153 compatible = "snps,dwmac-mdio";
154 phy0: ethernet-phy@0 {
161 pinctrl-names = "default", "sleep";
162 pinctrl-0 = <&fmc_pins_a>;
163 pinctrl-1 = <&fmc_sleep_pins_a>;
165 #address-cells = <1>;
171 #address-cells = <1>;
177 pinctrl-names = "default";
178 pinctrl-0 = <&i2c2_pins_a>;
179 i2c-scl-rising-time-ns = <185>;
180 i2c-scl-falling-time-ns = <20>;
184 compatible = "ovti,ov5640";
186 clocks = <&clk_ext_camera>;
187 clock-names = "xclk";
188 DOVDD-supply = <&v2v8>;
189 powerdown-gpios = <&stmfx_pinctrl 18 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>;
190 reset-gpios = <&stmfx_pinctrl 19 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;
196 remote-endpoint = <&dcmi_0>;
198 data-shift = <2>; /* lines 9:2 are used */
207 compatible = "st,stmfx-0300";
209 interrupts = <8 IRQ_TYPE_EDGE_RISING>;
210 interrupt-parent = <&gpioi>;
211 vdd-supply = <&v3v3>;
213 stmfx_pinctrl: stmfx-pin-controller {
214 compatible = "st,stmfx-0300-pinctrl";
217 interrupt-controller;
218 #interrupt-cells = <2>;
219 gpio-ranges = <&stmfx_pinctrl 0 0 24>;
221 joystick_pins: joystick {
222 pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
230 pinctrl-names = "default";
231 pinctrl-0 = <&i2c5_pins_a>;
232 i2c-scl-rising-time-ns = <185>;
233 i2c-scl-falling-time-ns = <20>;
241 #address-cells = <1>;
244 ltdc_ep0_out: endpoint@0 {
246 remote-endpoint = <&dsi_in>;
252 pinctrl-names = "default", "sleep";
253 pinctrl-0 = <&m_can1_pins_a>;
254 pinctrl-1 = <&m_can1_sleep_pins_a>;
259 pinctrl-names = "default", "sleep";
260 pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
261 pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>;
262 reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
263 #address-cells = <1>;
267 flash0: mx66l51235l@0 {
268 compatible = "jedec,spi-nor";
270 spi-rx-bus-width = <4>;
271 spi-max-frequency = <108000000>;
272 #address-cells = <1>;
276 flash1: mx66l51235l@1 {
277 compatible = "jedec,spi-nor";
279 spi-rx-bus-width = <4>;
280 spi-max-frequency = <108000000>;
281 #address-cells = <1>;
287 pinctrl-names = "default", "opendrain", "sleep";
288 pinctrl-0 = <&sdmmc3_b4_pins_a>;
289 pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
290 pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
294 vmmc-supply = <&v3v3>;
299 pinctrl-names = "default";
300 pinctrl-0 = <&spi1_pins_a>;
305 /* spare dmas for other usage (un-delete to enable pwm capture) */
306 /delete-property/dmas;
307 /delete-property/dma-names;
310 pinctrl-0 = <&pwm2_pins_a>;
311 pinctrl-1 = <&pwm2_sleep_pins_a>;
312 pinctrl-names = "default", "sleep";
321 /delete-property/dmas;
322 /delete-property/dma-names;
325 pinctrl-0 = <&pwm8_pins_a>;
326 pinctrl-1 = <&pwm8_sleep_pins_a>;
327 pinctrl-names = "default", "sleep";
336 /delete-property/dmas;
337 /delete-property/dma-names;
340 pinctrl-0 = <&pwm12_pins_a>;
341 pinctrl-1 = <&pwm12_sleep_pins_a>;
342 pinctrl-names = "default", "sleep";
351 phys = <&usbphyc_port0>;
356 dr_mode = "peripheral";
357 phys = <&usbphyc_port1 0>;
358 phy-names = "usb2-phy";