arch/arm/boot/dts/ste-ux500-samsung-skomer.dts

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * Devicetree for the Samsung XCover 2 GT-S7710 also known as Skomer.
   4  */
   5
   6 /dts-v1/;
   7 #include "ste-db8500.dtsi"
   8 #include "ste-ab8505.dtsi"
   9 #include "ste-dbx5x0-pinctrl.dtsi"
  10 #include <dt-bindings/gpio/gpio.h>
  11 #include <dt-bindings/leds/common.h>
  12 #include <dt-bindings/input/input.h>
  13 #include <dt-bindings/interrupt-controller/irq.h>
  14
  15 / {
  16         model = "Samsung XCover 2 (GT-S7710)";
  17         compatible = "samsung,skomer", "st-ericsson,u8500";
  18
  19         chosen {
  20                 stdout-path = &serial2;
  21         };
  22
  23         battery: battery {
  24                 compatible = "samsung,eb485159lu";
  25         };
  26
  27         /* TI TXS0206 level translator for 2.9 V */
  28         sd_level_translator: regulator-gpio {
  29                 compatible = "regulator-fixed";
  30
  31                 /* GPIO87 EN */
  32                 gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
  33                 enable-active-high;
  34
  35                 regulator-name = "sd-level-translator";
  36                 regulator-min-microvolt = <2900000>;
  37                 regulator-max-microvolt = <2900000>;
  38                 regulator-type = "voltage";
  39
  40                 startup-delay-us = <200>;
  41
  42                 pinctrl-names = "default";
  43                 pinctrl-0 = <&sd_level_translator_default>;
  44         };
  45
  46         /* External LDO MIC5366-3.3YMT for eMMC */
  47         ldo_3v3_reg: regulator-gpio-ldo-3v3 {
  48                 compatible = "regulator-fixed";
  49                 regulator-name = "en-3v3-fixed-supply";
  50                 regulator-min-microvolt = <3300000>;
  51                 regulator-max-microvolt = <3300000>;
  52                 gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>;
  53                 startup-delay-us = <5000>;
  54                 enable-active-high;
  55                 pinctrl-names = "default";
  56                 pinctrl-0 = <&emmc_ldo_en_default_mode>;
  57         };
  58
  59         wlan_en: regulator-gpio-wlan-en {
  60                 compatible = "regulator-fixed";
  61                 regulator-name = "wl-reg-on";
  62                 regulator-min-microvolt = <3000000>;
  63                 regulator-max-microvolt = <3000000>;
  64                 startup-delay-us = <200000>;
  65                 /* GPIO215 WLAN_EN */
  66                 gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
  67                 enable-active-high;
  68                 pinctrl-names = "default";
  69                 pinctrl-0 = <&wlan_en_default_mode>;
  70         };
  71
  72         vibrator {
  73                 compatible = "gpio-vibrator";
  74                 enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
  75                 pinctrl-names = "default";
  76                 pinctrl-0 = <&vibrator_default>;
  77         };
  78
  79         gpio-keys {
  80                 compatible = "gpio-keys";
  81                 pinctrl-names = "default";
  82                 pinctrl-0 = <&gpio_keys_default_mode>;
  83
  84                 button-home {
  85                         linux,code = <KEY_HOME>;
  86                         label = "HOME";
  87                         /* GPIO91 */
  88                         gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
  89                 };
  90                 button-volup {
  91                         linux,code = <KEY_VOLUMEUP>;
  92                         label = "VOL+";
  93                         /* GPIO67 */
  94                         gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
  95                 };
  96                 button-voldown {
  97                         linux,code = <KEY_VOLUMEDOWN>;
  98                         label = "VOL-";
  99                         /* GPIO92 */
 100                         gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
 101                 };
 102                 button-menu {
 103                         linux,code = <KEY_MENU>;
 104                         label = "MENU";
 105                         /* GPIO204 */
 106                         gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
 107                 };
 108                 button-back {
 109                         linux,code = <KEY_BACK>;
 110                         label = "BACK";
 111                         /* GPIO205 */
 112                         gpios = <&gpio6 13 GPIO_ACTIVE_LOW>;
 113                 };
 114         };
 115
 116         ktd253: backlight {
 117                 compatible = "kinetic,ktd253";
 118                 /* GPIO 69 */
 119                 enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
 120                 /* Default to 13/32 brightness */
 121                 default-brightness = <13>;
 122                 pinctrl-names = "default";
 123                 pinctrl-0 = <&gpio_backlight_default_mode>;
 124         };
 125
 126         /* Richtek RT8515GQW Flash LED Driver IC */
 127         flash {
 128                 compatible = "richtek,rt8515";
 129                 /* GPIO 140 */
 130                 enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
 131                 /* GPIO 141 */
 132                 ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
 133                 /*
 134                  * RFS is 16 kOhm and RTS is 100 kOhm giving
 135                  * the flash max current 343mA and torch max
 136                  * current 55 mA.
 137                  */
 138                 richtek,rfs-ohms = <16000>;
 139                 richtek,rts-ohms = <100000>;
 140                 pinctrl-names = "default";
 141                 pinctrl-0 = <&gpio_flash_default_mode>;
 142
 143                 led {
 144                         function = LED_FUNCTION_FLASH;
 145                         color = <LED_COLOR_ID_WHITE>;
 146                         flash-max-timeout-us = <250000>;
 147                         flash-max-microamp = <343750>;
 148                         led-max-microamp = <55000>;
 149                 };
 150         };
 151
 152         i2c-gpio-0 {
 153                 compatible = "i2c-gpio";
 154                 sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 155                 scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 156                 pinctrl-names = "default";
 157                 pinctrl-0 = <&i2c_gpio_0_default>;
 158                 #address-cells = <1>;
 159                 #size-cells = <0>;
 160                 /* TODO: this should be used by the NCP6914 Camera power management unit */
 161         };
 162
 163         i2c-gpio-1 {
 164                 compatible = "i2c-gpio";
 165                 sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 166                 scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 167                 pinctrl-names = "default";
 168                 pinctrl-0 = <&i2c_gpio_1_default>;
 169                 #address-cells = <1>;
 170                 #size-cells = <0>;
 171                 magnetometer@c {
 172                         compatible = "alps,hscdtd008a";
 173                         reg = <0x0c>;
 174                         avdd-supply = <&ab8500_ldo_aux1_reg>;
 175                         dvdd-supply = <&ab8500_ldo_aux8_reg>;
 176                 };
 177         };
 178
 179         soc {
 180                 // External Micro SD slot
 181                 mmc@80126000 {
 182                         arm,primecell-periphid = <0x10480180>;
 183                         max-frequency = <100000000>;
 184                         bus-width = <4>;
 185                         cap-sd-highspeed;
 186                         cap-mmc-highspeed;
 187                         /* All direction control is used */
 188                         st,sig-pin-fbclk;
 189                         full-pwr-cycle;
 190                         vmmc-supply = <&ab8500_ldo_aux3_reg>;
 191                         vqmmc-supply = <&sd_level_translator>;
 192                         pinctrl-names = "default", "sleep";
 193                         pinctrl-0 = <&mc0_a_1_default>;
 194                         pinctrl-1 = <&mc0_a_1_sleep>;
 195                         status = "okay";
 196                 };
 197
 198                 // WLAN SDIO channel
 199                 mmc@80118000 {
 200                         arm,primecell-periphid = <0x10480180>;
 201                         max-frequency = <50000000>;
 202                         bus-width = <4>;
 203                         non-removable;
 204                         cap-sd-highspeed;
 205                         vmmc-supply = <&wlan_en>;
 206                         pinctrl-names = "default", "sleep";
 207                         pinctrl-0 = <&mc1_a_2_default>;
 208                         pinctrl-1 = <&mc1_a_2_sleep>;
 209                         status = "okay";
 210                         #address-cells = <1>;
 211                         #size-cells = <0>;
 212
 213                         wifi@1 {
 214                                 compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
 215                                 reg = <1>;
 216                                 /* GPIO216 WL_HOST_WAKE */
 217                                 interrupt-parent = <&gpio6>;
 218                                 interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
 219                                 interrupt-names = "host-wake";
 220                                 pinctrl-names = "default";
 221                                 pinctrl-0 = <&wlan_default_mode>;
 222                         };
 223                 };
 224
 225                 /*
 226                  * eMMC seems to be mostly Samsung KLM4G1YE4C "4YMD1R"
 227                  */
 228                 mmc@80005000 {
 229                         arm,primecell-periphid = <0x10480180>;
 230                         max-frequency = <100000000>;
 231                         bus-width = <8>;
 232                         non-removable;
 233                         cap-mmc-highspeed;
 234                         mmc-ddr-1_8v;
 235                         no-sdio;
 236                         no-sd;
 237                         /* From datasheet page 26 figure 9: 300 ms set-up time for 4GB */
 238                         post-power-on-delay-ms = <300>;
 239                         vmmc-supply = <&ldo_3v3_reg>;
 240                         pinctrl-names = "default", "sleep";
 241                         pinctrl-0 = <&mc2_a_1_default>;
 242                         pinctrl-1 = <&mc2_a_1_sleep>;
 243
 244                         status = "okay";
 245                 };
 246
 247                 /* GBF (Bluetooth) UART */
 248                 uart@80120000 {
 249                         pinctrl-names = "default", "sleep";
 250                         pinctrl-0 = <&u0_a_1_default>;
 251                         pinctrl-1 = <&u0_a_1_sleep>;
 252                         status = "okay";
 253
 254                         /* FIXME: not quite working yet, probably needs regulators */
 255                         bluetooth {
 256                                 /* BCM4334B0 actually */
 257                                 compatible = "brcm,bcm4330-bt";
 258                                 shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
 259                                 device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
 260                                 host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
 261                                 pinctrl-names = "default";
 262                                 pinctrl-0 = <&bluetooth_default_mode>;
 263                         };
 264                 };
 265
 266                 /* GPF UART */
 267                 uart@80121000 {
 268                         status = "okay";
 269                         pinctrl-names = "default", "sleep";
 270                         pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
 271                         pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
 272                 };
 273
 274                 /* Debugging console UART connected to AB8505 USB */
 275                 uart@80007000 {
 276                         status = "okay";
 277                         pinctrl-names = "default", "sleep";
 278                         pinctrl-0 = <&u2rxtx_c_1_default>;
 279                         pinctrl-1 = <&u2rxtx_c_1_sleep>;
 280                 };
 281
 282                 prcmu@80157000 {
 283                         ab8505 {
 284                                 ab8500_usb {
 285                                         pinctrl-names = "default", "sleep";
 286                                         pinctrl-0 = <&usb_a_1_default>;
 287                                         pinctrl-1 = <&usb_a_1_sleep>;
 288                                 };
 289
 290                                 ab8505-regulators {
 291                                         ab8500_ldo_aux1 {
 292                                                 /* Used for VDD for sensors */
 293                                                 regulator-name = "AUX1";
 294                                                 regulator-min-microvolt = <3000000>;
 295                                                 regulator-max-microvolt = <3300000>;
 296                                         };
 297
 298                                         ab8500_ldo_aux2 {
 299                                                 /* Supplies the Cypress TMA140 touchscreen only with 3.0V */
 300                                                 regulator-name = "AUX2";
 301                                                 regulator-min-microvolt = <3000000>;
 302                                                 regulator-max-microvolt = <3000000>;
 303                                         };
 304
 305                                         ab8500_ldo_aux3 {
 306                                                 /* Used for voltage for external MMC/SD card */
 307                                                 regulator-name = "AUX3";
 308                                                 regulator-min-microvolt = <1100000>;
 309                                                 regulator-max-microvolt = <3300000>;
 310                                         };
 311
 312                                         ab8500_ldo_aux4 {
 313                                                 regulator-name = "AUX4";
 314                                                 /* Hammer to 3.0V for the display */
 315                                                 regulator-min-microvolt = <3000000>;
 316                                                 regulator-max-microvolt = <3000000>;
 317                                         };
 318
 319                                         ab8500_ldo_aux5 {
 320                                                 regulator-name = "AUX5";
 321                                                 /* Intended for 1V8 for touchscreen but actually left unused */
 322                                                 regulator-min-microvolt = <1050000>;
 323                                                 regulator-max-microvolt = <2790000>;
 324                                         };
 325
 326                                         ab8500_ldo_aux6 {
 327                                                 regulator-name = "AUX6";
 328                                                 /* Hammer to 1.8V for the display */
 329                                                 regulator-min-microvolt = <1800000>;
 330                                                 regulator-max-microvolt = <1800000>;
 331                                         };
 332
 333                                         ab8500_ldo_aux8 {
 334                                                 /* Mostly VIO for sensors */
 335                                                 regulator-name = "AUX8";
 336                                         };
 337                                 };
 338                         };
 339                 };
 340
 341                 /* I2C0 */
 342                 i2c@80004000 {
 343                         status = "okay";
 344
 345                         pinctrl-names = "default", "sleep";
 346                         pinctrl-0 = <&i2c0_a_1_default>;
 347                         pinctrl-1 = <&i2c0_a_1_sleep>;
 348
 349                         proximity@44 {
 350                                 compatible = "sharp,gp2ap002s00f";
 351                                 clock-frequency = <400000>;
 352                                 reg = <0x44>;
 353
 354                                 interrupt-parent = <&gpio4>;
 355                                 interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
 356                                 vdd-supply = <&ab8500_ldo_aux1_reg>;
 357                                 vio-supply = <&ab8500_ldo_aux8_reg>;
 358                                 pinctrl-names = "default";
 359                                 pinctrl-0 = <&gp2ap002_skomer_default>;
 360                                 sharp,proximity-far-hysteresis = /bits/ 8 <0x2f>;
 361                                 sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>;
 362                         };
 363                 };
 364
 365
 366                 /* I2C2 */
 367                 i2c@80128000 {
 368                         status = "okay";
 369
 370                         pinctrl-names = "default", "sleep";
 371                         pinctrl-0 = <&i2c2_b_2_default>;
 372                         pinctrl-1 = <&i2c2_b_2_sleep>;
 373
 374                         accel@18 {
 375                                 compatible = "bosch,bma254";
 376                                 clock-frequency = <400000>;
 377                                 reg = <0x18>;
 378
 379                                 /* GPIO224 used as "smart alert" interrupt */
 380                                 interrupt-parent = <&gpio7>;
 381                                 interrupts = <0 IRQ_TYPE_EDGE_RISING>;
 382
 383                                 mount-matrix = "0", "-1", "0",
 384                                               "1", "0", "0",
 385                                                "0", "0", "1";
 386                                 vdd-supply = <&ab8500_ldo_aux1_reg>;
 387                                 vddio-supply = <&ab8500_ldo_aux8_reg>;
 388                                 pinctrl-names = "default";
 389                                 pinctrl-0 = <&bma254_skomer_default>;
 390                         };
 391                 };
 392
 393                 /* I2C3 */
 394                 i2c@80110000 {
 395                         status = "okay";
 396
 397                         pinctrl-names = "default", "sleep";
 398                         pinctrl-0 = <&i2c3_c_2_default>;
 399                         pinctrl-1 = <&i2c3_c_2_sleep>;
 400
 401                         /* Cypress CY8CTMA140 touchscreen */
 402                         touchscreen@20 {
 403                                 compatible = "cypress,cy8ctma140";
 404                                 clock-frequency = <400000>;
 405                                 reg = <0x20>;
 406
 407                                 touchscreen-size-x = <480>;
 408                                 touchscreen-size-y = <800>;
 409                                 touchscreen-max-pressure = <255>;
 410
 411                                 /* GPIO218 for IRQ */
 412                                 interrupt-parent = <&gpio6>;
 413                                 interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
 414
 415                                 /* VDD is "digital supply" nominally 1.71-3.6V */
 416                                 vdd-supply = <&ab8500_ldo_aux2_reg>;
 417                                 /* VCPIN is "analog supply", 2.7-3.6 V */
 418                                 vcpin-supply = <&ab8500_ldo_aux2_reg>;
 419
 420                                 pinctrl-names = "default";
 421                                 pinctrl-0 = <&tma140_skomer_default>;
 422                         };
 423                 };
 424
 425                 mcde@a0350000 {
 426                         status = "okay";
 427                         pinctrl-names = "default";
 428                         pinctrl-0 = <&dsi_default_mode>;
 429
 430                         dsi@a0351000 {
 431                                 panel {
 432                                         /* NT35510-based Hydis HVA40WV1 */
 433                                         compatible = "hydis,hva40wv1", "novatek,nt35510";
 434                                         reg = <0>;
 435                                         /* v_lcd_3v0 2.3-4.8V */
 436                                         vdd-supply = <&ab8500_ldo_aux4_reg>;
 437                                         /* v_lcd_1v8 1.65-3.3V */
 438                                         vddi-supply = <&ab8500_ldo_aux6_reg>;
 439                                         /* GPIO 139 */
 440                                         reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
 441                                         pinctrl-names = "default";
 442                                         pinctrl-0 = <&display_default_mode>;
 443                                         backlight = <&ktd253>;
 444                                 };
 445                         };
 446                 };
 447         };
 448 };
 449
 450 &pinctrl {
 451         sdi0 {
 452                 mc0_a_1_default {
 453                         default_cfg1 {
 454                                 /* GPIO18, 19 & 20 unused so pull down */
 455                                 ste,config = <&gpio_in_pd>;
 456                         };
 457                 };
 458         };
 459
 460         /* This is a reset line for the eMMC */
 461         sdi2 {
 462                 mc2_a_1_default {
 463                         default_cfg2 {
 464                                 pins = "GPIO130_C8"; /* FBCLK */
 465                                 ste,config = <&gpio_in_pd>;
 466                         };
 467                 };
 468         };
 469
 470         mcde {
 471                 dsi_default_mode: dsi_default {
 472                         default_mux1 {
 473                                 /* Mux in VSI0 used for DSI TE */
 474                                 function = "lcd";
 475                                 groups = "lcdvsi0_a_1"; /* VSI0 for LCD */
 476                         };
 477                         default_cfg1 {
 478                                 pins = "GPIO68_E1"; /* VSI0 */
 479                                 ste,config = <&in_nopull>;
 480                         };
 481                 };
 482         };
 483
 484         /* Two GPIO lines used by the display */
 485         display {
 486                 display_default_mode: display_default {
 487                         skomer_cfg1 {
 488                                 /*
 489                                  * OLED DETECT or check_pba, this appears to be high
 490                                  * on "PBA" which I guess is "prototype board A".
 491                                  */
 492                                 pins = "GPIO93_B7";
 493                                 ste,config = <&gpio_in_nopull>;
 494                         };
 495                         skomer_cfg2 {
 496                                 pins = "GPIO139_C9";
 497                                 /*
 498                                  * MIPI_DSI0_RESET_N resets the display, leave high
 499                                  * (de-asserted) so we only assert reset explicitly
 500                                  * from the display driver.
 501                                  */
 502                                 ste,config = <&gpio_out_hi>;
 503                         };
 504                 };
 505         };
 506         backlight {
 507                 gpio_backlight_default_mode: backlight_default {
 508                         skomer_cfg1 {
 509                                 pins = "GPIO69_E2"; /* LCD_BL_CTRL */
 510                                 ste,config = <&gpio_out_lo>;
 511                         };
 512                 };
 513         };
 514         flash {
 515                 gpio_flash_default_mode: flash_default {
 516                         skomer_cfg1 {
 517                                 pins = "GPIO140_B11", "GPIO141_C12";
 518                                 ste,config = <&gpio_out_lo>;
 519                         };
 520                 };
 521         };
 522         /* GPIO that enables the 2.9V SD card level translator */
 523         sd-level-translator {
 524                 sd_level_translator_default: sd_level_translator_default {
 525                         /* level shifter on GPIO87 */
 526                         skomer_cfg1 {
 527                                 pins = "GPIO87_B3";
 528                                 ste,config = <&gpio_out_hi>;
 529                         };
 530                 };
 531         };
 532         /* GPIO that enables the LDO regulator for the eMMC */
 533         emmc-ldo {
 534                 emmc_ldo_en_default_mode: emmc_ldo_default {
 535                         /* LDO enable on GPIO223 */
 536                         skomer_cfg1 {
 537                                 pins = "GPIO223_AH9";
 538                                 ste,config = <&gpio_out_hi>;
 539                         };
 540                 };
 541         };
 542         /* GPIO keys */
 543         gpio-keys {
 544                 gpio_keys_default_mode: gpio_keys_default {
 545                         skomer_cfg1 {
 546                                 pins = "GPIO67_G2", /* VOL UP */
 547                                        "GPIO91_B6", /* HOME */
 548                                        "GPIO92_D6", /* VOL DOWN */
 549                                        "GPIO204_AF23", /* MENU */
 550                                        "GPIO205_AG23"; /* BACK */
 551                                         ste,config = <&gpio_in_pu>;
 552                         };
 553                 };
 554         };
 555         /* Interrupt line for BMA254 */
 556         bma254 {
 557                 bma254_skomer_default: bma254_skomer {
 558                         skomer_cfg1 {
 559                                 pins = "GPIO224_AG9";
 560                                 ste,config = <&gpio_in_pd>;
 561                         };
 562                 };
 563         };
 564         /* Interrupt line for light/proximity sensor GP2AP002 */
 565         gp2ap002 {
 566                 gp2ap002_skomer_default: gp2ap002_skomer {
 567                         skomer_cfg1 {
 568                                 pins = "GPIO146_D13";
 569                                 ste,config = <&gpio_in_nopull>;
 570                         };
 571                 };
 572         };
 573         /* GPIO-based I2C bus for NCP6914 */
 574         i2c-gpio-0 {
 575                 i2c_gpio_0_default: i2c_gpio_0 {
 576                         skomer_cfg1 {
 577                                 pins = "GPIO143_D12", "GPIO144_B13";
 578                                 ste,config = <&gpio_in_nopull>;
 579                         };
 580                 };
 581         };
 582         /* GPIO-based I2C bus for ALPS HSCD compass */
 583         i2c-gpio-1 {
 584                 i2c_gpio_1_default: i2c_gpio_1 {
 585                         skomer_cfg1 {
 586                                 pins = "GPIO151_B17", "GPIO152_D16";
 587                                 ste,config = <&gpio_in_nopull>;
 588                         };
 589                 };
 590         };
 591         wlan {
 592                 wlan_default_mode: wlan_default {
 593                         skomer_cfg1 {
 594                                 pins = "GPIO216_AG12";
 595                                 ste,config = <&gpio_in_pd>;
 596                         };
 597                 };
 598                 wlan_en_default_mode: wlan_en_default {
 599                         skomer_cfg2 {
 600                                 pins = "GPIO215_AH13";
 601                                 ste,config = <&gpio_out_lo>;
 602                         };
 603                 };
 604         };
 605         bluetooth {
 606                 bluetooth_default_mode: bluetooth_default {
 607                         skomer_cfg1 {
 608                                 pins = "GPIO199_AH23", "GPIO222_AJ9";
 609                                 ste,config = <&gpio_out_lo>;
 610                         };
 611                         skomer_cfg2 {
 612                                 pins = "GPIO97_D9";
 613                                 ste,config = <&gpio_in_nopull>;
 614                         };
 615                 };
 616         };
 617         vibrator {
 618                 vibrator_default: vibrator_default {
 619                         skomer_cfg1 {
 620                                 pins = "GPIO195_AG28";  /* MOT_EN */
 621                                 ste,config = <&gpio_out_lo>;
 622                         };
 623                 };
 624         };
 625         /* Interrupt line for the Cypress TMA140 touchscreen */
 626         touchscreen {
 627                 tma140_skomer_default: tma140_skomer {
 628                         skomer_cfg1 {
 629                                 pins = "GPIO218_AH11";
 630                                 ste,config = <&gpio_in_nopull>;
 631                         };
 632                 };
 633         };
 634 };
 635
 636 &ab8505_gpio {
 637         /* Hog a few default settings */
 638         pinctrl-names = "default";
 639         pinctrl-0 = <&gpio_default>;
 640
 641         gpio {
 642                 gpio_default: gpio_default {
 643                         skomer_mux {
 644                                 /* Change unused pins to GPIO mode */
 645                                 function = "gpio";
 646                                 groups = "gpio3_a_1",   /* default: SysClkReq4 */
 647                                          "gpio14_a_1";  /* default: PWMOut1 */
 648                         };
 649                         skomer_cfg1 {
 650                                 pins = "GPIO11_B17", "GPIO13_D17", "GPIO50_L4";
 651                                 bias-disable;
 652                         };
 653                 };
 654         };
 655 };