arch/arm/boot/dts/ste-ux500-samsung-skomer.dts

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * Devicetree for the Samsung XCover 2 GT-S7710 also known as Skomer.
   4  */
   5
   6 /dts-v1/;
   7 #include "ste-db8500.dtsi"
   8 #include "ste-ab8505.dtsi"
   9 #include "ste-dbx5x0-pinctrl.dtsi"
  10 #include <dt-bindings/gpio/gpio.h>
  11 #include <dt-bindings/leds/common.h>
  12 #include <dt-bindings/input/input.h>
  13 #include <dt-bindings/interrupt-controller/irq.h>
  14
  15 / {
  16         model = "Samsung XCover 2 (GT-S7710)";
  17         compatible = "samsung,skomer", "st-ericsson,u8500";
  18
  19         chosen {
  20                 stdout-path = &serial2;
  21         };
  22
  23         /* TI TXS0206 level translator for 2.9 V */
  24         sd_level_translator: regulator-gpio {
  25                 compatible = "regulator-fixed";
  26
  27                 /* GPIO87 EN */
  28                 gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
  29                 enable-active-high;
  30
  31                 regulator-name = "sd-level-translator";
  32                 regulator-min-microvolt = <2900000>;
  33                 regulator-max-microvolt = <2900000>;
  34                 regulator-type = "voltage";
  35
  36                 startup-delay-us = <200>;
  37
  38                 pinctrl-names = "default";
  39                 pinctrl-0 = <&sd_level_translator_default>;
  40         };
  41
  42         /* External LDO MIC5366-3.3YMT for eMMC */
  43         ldo_3v3_reg: regulator-gpio-ldo-3v3 {
  44                 compatible = "regulator-fixed";
  45                 regulator-name = "en-3v3-fixed-supply";
  46                 regulator-min-microvolt = <3300000>;
  47                 regulator-max-microvolt = <3300000>;
  48                 gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>;
  49                 startup-delay-us = <5000>;
  50                 enable-active-high;
  51                 pinctrl-names = "default";
  52                 pinctrl-0 = <&emmc_ldo_en_default_mode>;
  53         };
  54
  55         wlan_en: regulator-gpio-wlan-en {
  56                 compatible = "regulator-fixed";
  57                 regulator-name = "wl-reg-on";
  58                 regulator-min-microvolt = <3000000>;
  59                 regulator-max-microvolt = <3000000>;
  60                 startup-delay-us = <200000>;
  61                 /* GPIO215 WLAN_EN */
  62                 gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
  63                 enable-active-high;
  64                 pinctrl-names = "default";
  65                 pinctrl-0 = <&wlan_en_default_mode>;
  66         };
  67
  68         vibrator {
  69                 compatible = "gpio-vibrator";
  70                 enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
  71                 pinctrl-names = "default";
  72                 pinctrl-0 = <&vibrator_default>;
  73         };
  74
  75         gpio-keys {
  76                 compatible = "gpio-keys";
  77                 pinctrl-names = "default";
  78                 pinctrl-0 = <&gpio_keys_default_mode>;
  79
  80                 button-home {
  81                         linux,code = <KEY_HOME>;
  82                         label = "HOME";
  83                         /* GPIO91 */
  84                         gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
  85                 };
  86                 button-volup {
  87                         linux,code = <KEY_VOLUMEUP>;
  88                         label = "VOL+";
  89                         /* GPIO67 */
  90                         gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
  91                 };
  92                 button-voldown {
  93                         linux,code = <KEY_VOLUMEDOWN>;
  94                         label = "VOL-";
  95                         /* GPIO92 */
  96                         gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
  97                 };
  98                 button-menu {
  99                         linux,code = <KEY_MENU>;
 100                         label = "MENU";
 101                         /* GPIO204 */
 102                         gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
 103                 };
 104                 button-back {
 105                         linux,code = <KEY_BACK>;
 106                         label = "BACK";
 107                         /* GPIO205 */
 108                         gpios = <&gpio6 13 GPIO_ACTIVE_LOW>;
 109                 };
 110         };
 111
 112         ktd253: backlight {
 113                 compatible = "kinetic,ktd253";
 114                 /* GPIO 69 */
 115                 enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
 116                 /* Default to 13/32 brightness */
 117                 default-brightness = <13>;
 118                 pinctrl-names = "default";
 119                 pinctrl-0 = <&gpio_backlight_default_mode>;
 120         };
 121
 122         /* Richtek RT8515GQW Flash LED Driver IC */
 123         flash {
 124                 compatible = "richtek,rt8515";
 125                 /* GPIO 140 */
 126                 enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
 127                 /* GPIO 141 */
 128                 ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
 129                 /*
 130                  * RFS is 16 kOhm and RTS is 100 kOhm giving
 131                  * the flash max current 343mA and torch max
 132                  * current 55 mA.
 133                  */
 134                 richtek,rfs-ohms = <16000>;
 135                 richtek,rts-ohms = <100000>;
 136                 pinctrl-names = "default";
 137                 pinctrl-0 = <&gpio_flash_default_mode>;
 138
 139                 led {
 140                         function = LED_FUNCTION_FLASH;
 141                         color = <LED_COLOR_ID_WHITE>;
 142                         flash-max-timeout-us = <250000>;
 143                         flash-max-microamp = <343750>;
 144                         led-max-microamp = <55000>;
 145                 };
 146         };
 147
 148         i2c-gpio-0 {
 149                 compatible = "i2c-gpio";
 150                 sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 151                 scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 152                 pinctrl-names = "default";
 153                 pinctrl-0 = <&i2c_gpio_0_default>;
 154                 #address-cells = <1>;
 155                 #size-cells = <0>;
 156                 /* TODO: this should be used by the NCP6914 Camera power management unit */
 157         };
 158
 159         i2c-gpio-1 {
 160                 compatible = "i2c-gpio";
 161                 sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 162                 scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 163                 pinctrl-names = "default";
 164                 pinctrl-0 = <&i2c_gpio_1_default>;
 165                 #address-cells = <1>;
 166                 #size-cells = <0>;
 167                 magnetometer@c {
 168                         compatible = "alps,hscdtd008a";
 169                         reg = <0x0c>;
 170                         avdd-supply = <&ab8500_ldo_aux1_reg>;
 171                         dvdd-supply = <&ab8500_ldo_aux8_reg>;
 172                 };
 173         };
 174
 175         soc {
 176                 // External Micro SD slot
 177                 mmc@80126000 {
 178                         arm,primecell-periphid = <0x10480180>;
 179                         max-frequency = <100000000>;
 180                         bus-width = <4>;
 181                         cap-sd-highspeed;
 182                         cap-mmc-highspeed;
 183                         /* All direction control is used */
 184                         st,sig-dir-cmd;
 185                         st,sig-dir-dat0;
 186                         st,sig-dir-dat2;
 187                         st,sig-dir-dat31;
 188                         st,sig-pin-fbclk;
 189                         full-pwr-cycle;
 190                         vmmc-supply = <&ab8500_ldo_aux3_reg>;
 191                         vqmmc-supply = <&sd_level_translator>;
 192                         pinctrl-names = "default", "sleep";
 193                         pinctrl-0 = <&mc0_a_1_default>;
 194                         pinctrl-1 = <&mc0_a_1_sleep>;
 195                         status = "okay";
 196                 };
 197
 198                 // WLAN SDIO channel
 199                 mmc@80118000 {
 200                         arm,primecell-periphid = <0x10480180>;
 201                         max-frequency = <50000000>;
 202                         bus-width = <4>;
 203                         non-removable;
 204                         cap-sd-highspeed;
 205                         vmmc-supply = <&wlan_en>;
 206                         pinctrl-names = "default", "sleep";
 207                         pinctrl-0 = <&mc1_a_2_default>;
 208                         pinctrl-1 = <&mc1_a_2_sleep>;
 209                         status = "okay";
 210                         #address-cells = <1>;
 211                         #size-cells = <0>;
 212
 213                         wifi@1 {
 214                                 compatible = "brcm,bcm4329-fmac";
 215                                 reg = <1>;
 216                                 /* GPIO216 WL_HOST_WAKE */
 217                                 interrupt-parent = <&gpio6>;
 218                                 interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
 219                                 interrupt-names = "host-wake";
 220                                 pinctrl-names = "default";
 221                                 pinctrl-0 = <&wlan_default_mode>;
 222                         };
 223                 };
 224
 225                 // eMMC
 226                 mmc@80005000 {
 227                         arm,primecell-periphid = <0x10480180>;
 228                         max-frequency = <100000000>;
 229                         bus-width = <8>;
 230                         non-removable;
 231                         cap-mmc-highspeed;
 232                         mmc-ddr-1_8v;
 233                         vmmc-supply = <&ldo_3v3_reg>;
 234                         pinctrl-names = "default", "sleep";
 235                         pinctrl-0 = <&mc2_a_1_default>;
 236                         pinctrl-1 = <&mc2_a_1_sleep>;
 237
 238                         status = "okay";
 239                 };
 240
 241                 /* GBF (Bluetooth) UART */
 242                 uart@80120000 {
 243                         pinctrl-names = "default", "sleep";
 244                         pinctrl-0 = <&u0_a_1_default>;
 245                         pinctrl-1 = <&u0_a_1_sleep>;
 246                         status = "okay";
 247
 248                         /* FIXME: not quite working yet, probably needs regulators */
 249                         bluetooth {
 250                                 compatible = "brcm,bcm4330-bt";
 251                                 shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
 252                                 device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
 253                                 host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
 254                                 pinctrl-names = "default";
 255                                 pinctrl-0 = <&bluetooth_default_mode>;
 256                         };
 257                 };
 258
 259                 /* GPF UART */
 260                 uart@80121000 {
 261                         status = "okay";
 262                         pinctrl-names = "default", "sleep";
 263                         pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
 264                         pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
 265                 };
 266
 267                 /* Debugging console UART connected to AB8505 USB */
 268                 uart@80007000 {
 269                         status = "okay";
 270                         pinctrl-names = "default", "sleep";
 271                         pinctrl-0 = <&u2rxtx_c_1_default>;
 272                         pinctrl-1 = <&u2rxtx_c_1_sleep>;
 273                 };
 274
 275                 prcmu@80157000 {
 276                         ab8505 {
 277                                 ab8500_usb {
 278                                         pinctrl-names = "default", "sleep";
 279                                         pinctrl-0 = <&usb_a_1_default>;
 280                                         pinctrl-1 = <&usb_a_1_sleep>;
 281                                 };
 282
 283                                 ab8505-regulators {
 284                                         ab8500_ldo_aux1 {
 285                                                 /* Used for VDD for sensors */
 286                                                 regulator-name = "AUX1";
 287                                                 regulator-min-microvolt = <3000000>;
 288                                                 regulator-max-microvolt = <3300000>;
 289                                         };
 290
 291                                         ab8500_ldo_aux2 {
 292                                                 /* Supplies the Cypress TMA140 touchscreen only with 3.3V */
 293                                                 regulator-name = "AUX2";
 294                                                 regulator-min-microvolt = <3300000>;
 295                                                 regulator-max-microvolt = <3300000>;
 296                                         };
 297
 298                                         ab8500_ldo_aux3 {
 299                                                 /* Used for voltage for external MMC/SD card */
 300                                                 regulator-name = "AUX3";
 301                                                 regulator-min-microvolt = <1100000>;
 302                                                 regulator-max-microvolt = <3300000>;
 303                                         };
 304
 305                                         ab8500_ldo_aux4 {
 306                                                 regulator-name = "AUX4";
 307                                                 /* Hammer to 3.0V for the display */
 308                                                 regulator-min-microvolt = <3000000>;
 309                                                 regulator-max-microvolt = <3000000>;
 310                                         };
 311
 312                                         ab8500_ldo_aux5 {
 313                                                 regulator-name = "AUX5";
 314                                                 regulator-min-microvolt = <1050000>;
 315                                                 regulator-max-microvolt = <2790000>;
 316                                                 regulator-always-on;
 317                                         };
 318
 319                                         ab8500_ldo_aux6 {
 320                                                 regulator-name = "AUX6";
 321                                                 /* Hammer to 1.8V for the display */
 322                                                 regulator-min-microvolt = <1800000>;
 323                                                 regulator-max-microvolt = <1800000>;
 324                                         };
 325
 326                                         ab8500_ldo_aux8 {
 327                                                 /* Mostly VIO for sensors */
 328                                                 regulator-name = "AUX8";
 329                                         };
 330                                 };
 331                         };
 332                 };
 333
 334                 /* I2C0 */
 335                 i2c@80004000 {
 336                         status = "okay";
 337
 338                         pinctrl-names = "default", "sleep";
 339                         pinctrl-0 = <&i2c0_a_1_default>;
 340                         pinctrl-1 = <&i2c0_a_1_sleep>;
 341
 342                         proximity@44 {
 343                                 compatible = "sharp,gp2ap002s00f";
 344                                 clock-frequency = <400000>;
 345                                 reg = <0x44>;
 346
 347                                 interrupt-parent = <&gpio4>;
 348                                 interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
 349                                 vdd-supply = <&ab8500_ldo_aux1_reg>;
 350                                 vio-supply = <&ab8500_ldo_aux8_reg>;
 351                                 pinctrl-names = "default";
 352                                 pinctrl-0 = <&gp2ap002_skomer_default>;
 353                                 sharp,proximity-far-hysteresis = /bits/ 8 <0x2f>;
 354                                 sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>;
 355                         };
 356                 };
 357
 358
 359                 /* I2C2 */
 360                 i2c@80128000 {
 361                         status = "okay";
 362
 363                         pinctrl-names = "default", "sleep";
 364                         pinctrl-0 = <&i2c2_b_2_default>;
 365                         pinctrl-1 = <&i2c2_b_2_sleep>;
 366
 367                         accel@18 {
 368                                 compatible = "bosch,bma254";
 369                                 clock-frequency = <400000>;
 370                                 reg = <0x18>;
 371
 372                                 /* GPIO224 used as "smart alert" interrupt */
 373                                 interrupt-parent = <&gpio7>;
 374                                 interrupts = <0 IRQ_TYPE_EDGE_RISING>;
 375
 376                                 mount-matrix = "0", "-1", "0",
 377                                               "1", "0", "0",
 378                                                "0", "0", "1";
 379                                 vdd-supply = <&ab8500_ldo_aux1_reg>;
 380                                 vddio-supply = <&ab8500_ldo_aux8_reg>;
 381                                 pinctrl-names = "default";
 382                                 pinctrl-0 = <&bma254_skomer_default>;
 383                         };
 384                 };
 385
 386                 /* I2C3 */
 387                 i2c@80110000 {
 388                         status = "okay";
 389
 390                         pinctrl-names = "default", "sleep";
 391                         pinctrl-0 = <&i2c3_c_2_default>;
 392                         pinctrl-1 = <&i2c3_c_2_sleep>;
 393
 394                         /* Cypress CY8CTMA140 touchscreen */
 395                         touchscreen@20 {
 396                                 compatible = "cypress,cy8ctma140";
 397                                 clock-frequency = <400000>;
 398                                 reg = <0x20>;
 399
 400                                 touchscreen-size-x = <480>;
 401                                 touchscreen-size-y = <800>;
 402                                 touchscreen-max-pressure = <255>;
 403
 404                                 /* GPIO218 for IRQ */
 405                                 interrupt-parent = <&gpio6>;
 406                                 interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
 407
 408                                 /* VDD is "digital supply" nominally 1.71-3.6V */
 409                                 vdd-supply = <&ab8500_ldo_aux2_reg>;
 410                                 /* VCPIN is "analog supply", 2.7-3.6 V */
 411                                 vcpin-supply = <&ab8500_ldo_aux2_reg>;
 412
 413                                 pinctrl-names = "default";
 414                                 pinctrl-0 = <&tma140_skomer_default>;
 415                         };
 416                 };
 417
 418                 mcde@a0350000 {
 419                         status = "okay";
 420                         pinctrl-names = "default";
 421                         pinctrl-0 = <&dsi_default_mode>;
 422
 423                         dsi@a0351000 {
 424                                 panel {
 425                                         /* NT35510-based Hydis HVA40WV1 */
 426                                         compatible = "hydis,hva40wv1", "novatek,nt35510";
 427                                         reg = <0>;
 428                                         /* v_lcd_3v0 2.3-4.8V */
 429                                         vdd-supply = <&ab8500_ldo_aux4_reg>;
 430                                         /* v_lcd_1v8 1.65-3.3V */
 431                                         vddi-supply = <&ab8500_ldo_aux6_reg>;
 432                                         /* GPIO 139 */
 433                                         reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
 434                                         pinctrl-names = "default";
 435                                         pinctrl-0 = <&display_default_mode>;
 436                                         backlight = <&ktd253>;
 437                                 };
 438                         };
 439                 };
 440         };
 441 };
 442
 443 &pinctrl {
 444         /*
 445          * This extends the MC0 default config to include DAT32DIR
 446          * which is used by this machine. If we don't do this the
 447          * SD card does not work.
 448          */
 449         sdi0 {
 450                 mc0_a_1_default {
 451                         default_mux {
 452                                 function = "mc0";
 453                                 /* This machine uses the DAT31 pin */
 454                                 groups = "mc0_a_1", "mc0dat31dir_a_1";
 455                         };
 456                         default_cfg5 {
 457                                 pins = "GPIO21_AB3"; /* DAT31DIR */
 458                                 ste,config = <&out_hi>;
 459                         };
 460                 };
 461         };
 462
 463         /* The unused FBCLK needs to be pulled down on this machine */
 464         sdi2 {
 465                 mc2_a_1_default {
 466                         default_cfg2 {
 467                                 pins = "GPIO130_C8"; /* FBCLK */
 468                                 ste,config = <&in_pd>;
 469                         };
 470                 };
 471         };
 472
 473         mcde {
 474                 dsi_default_mode: dsi_default {
 475                         default_mux1 {
 476                                 /* Mux in VSI0 used for DSI TE */
 477                                 function = "lcd";
 478                                 groups = "lcdvsi0_a_1"; /* VSI0 for LCD */
 479                         };
 480                         default_cfg1 {
 481                                 pins = "GPIO68_E1"; /* VSI0 */
 482                                 ste,config = <&in_nopull>;
 483                         };
 484                 };
 485         };
 486
 487         /* Two GPIO lines used by the display */
 488         display {
 489                 display_default_mode: display_default {
 490                         skomer_cfg1 {
 491                                 /*
 492                                  * OLED DETECT or check_pba, this appears to be high
 493                                  * on "PBA" which I guess is "prototype board A".
 494                                  */
 495                                 pins = "GPIO93_B7";
 496                                 ste,config = <&gpio_in_nopull>;
 497                         };
 498                         skomer_cfg2 {
 499                                 pins = "GPIO139_C9";
 500                                 /*
 501                                  * MIPI_DSI0_RESET_N resets the display, leave high
 502                                  * (de-asserted) so we only assert reset explicitly
 503                                  * from the display driver.
 504                                  */
 505                                 ste,config = <&gpio_out_hi>;
 506                         };
 507                 };
 508         };
 509         backlight {
 510                 gpio_backlight_default_mode: backlight_default {
 511                         skomer_cfg1 {
 512                                 pins = "GPIO69_E2"; /* LCD_BL_CTRL */
 513                                 ste,config = <&gpio_out_lo>;
 514                         };
 515                 };
 516         };
 517         flash {
 518                 gpio_flash_default_mode: flash_default {
 519                         skomer_cfg1 {
 520                                 pins = "GPIO140_B11", "GPIO141_C12";
 521                                 ste,config = <&gpio_out_lo>;
 522                         };
 523                 };
 524         };
 525         /* GPIO that enables the 2.9V SD card level translator */
 526         sd-level-translator {
 527                 sd_level_translator_default: sd_level_translator_default {
 528                         /* level shifter on GPIO87 */
 529                         skomer_cfg1 {
 530                                 pins = "GPIO87_B3";
 531                                 ste,config = <&gpio_out_hi>;
 532                         };
 533                 };
 534         };
 535         /* GPIO that enables the LDO regulator for the eMMC */
 536         emmc-ldo {
 537                 emmc_ldo_en_default_mode: emmc_ldo_default {
 538                         /* LDO enable on GPIO223 */
 539                         skomer_cfg1 {
 540                                 pins = "GPIO223_AH9";
 541                                 ste,config = <&gpio_out_hi>;
 542                         };
 543                 };
 544         };
 545         /* GPIO keys */
 546         gpio-keys {
 547                 gpio_keys_default_mode: gpio_keys_default {
 548                         skomer_cfg1 {
 549                                 pins = "GPIO67_G2", /* VOL UP */
 550                                        "GPIO91_B6", /* HOME */
 551                                        "GPIO92_D6", /* VOL DOWN */
 552                                        "GPIO204_AF23", /* MENU */
 553                                        "GPIO205_AG23"; /* BACK */
 554                                         ste,config = <&gpio_in_pu>;
 555                         };
 556                 };
 557         };
 558         /* Interrupt line for BMA254 */
 559         bma254 {
 560                 bma254_skomer_default: bma254_skomer {
 561                         skomer_cfg1 {
 562                                 pins = "GPIO224_AG9";
 563                                 ste,config = <&gpio_in_pd>;
 564                         };
 565                 };
 566         };
 567         /* Interrupt line for light/proximity sensor GP2AP002 */
 568         gp2ap002 {
 569                 gp2ap002_skomer_default: gp2ap002_skomer {
 570                         skomer_cfg1 {
 571                                 pins = "GPIO146_D13";
 572                                 ste,config = <&gpio_in_nopull>;
 573                         };
 574                 };
 575         };
 576         /* GPIO-based I2C bus for NCP6914 */
 577         i2c-gpio-0 {
 578                 i2c_gpio_0_default: i2c_gpio_0 {
 579                         skomer_cfg1 {
 580                                 pins = "GPIO143_D12", "GPIO144_B13";
 581                                 ste,config = <&gpio_in_nopull>;
 582                         };
 583                 };
 584         };
 585         /* GPIO-based I2C bus for ALPS HSCD compass */
 586         i2c-gpio-1 {
 587                 i2c_gpio_1_default: i2c_gpio_1 {
 588                         skomer_cfg1 {
 589                                 pins = "GPIO151_B17", "GPIO152_D16";
 590                                 ste,config = <&gpio_in_nopull>;
 591                         };
 592                 };
 593         };
 594         wlan {
 595                 wlan_default_mode: wlan_default {
 596                         skomer_cfg1 {
 597                                 pins = "GPIO216_AG12";
 598                                 ste,config = <&gpio_in_pd>;
 599                         };
 600                 };
 601                 wlan_en_default_mode: wlan_en_default {
 602                         skomer_cfg2 {
 603                                 pins = "GPIO215_AH13";
 604                                 ste,config = <&gpio_out_lo>;
 605                         };
 606                 };
 607         };
 608         bluetooth {
 609                 bluetooth_default_mode: bluetooth_default {
 610                         skomer_cfg1 {
 611                                 pins = "GPIO199_AH23", "GPIO222_AJ9";
 612                                 ste,config = <&gpio_out_lo>;
 613                         };
 614                         skomer_cfg2 {
 615                                 pins = "GPIO97_D9";
 616                                 ste,config = <&gpio_in_nopull>;
 617                         };
 618                 };
 619         };
 620         vibrator {
 621                 vibrator_default: vibrator_default {
 622                         skomer_cfg1 {
 623                                 pins = "GPIO195_AG28";  /* MOT_EN */
 624                                 ste,config = <&gpio_out_lo>;
 625                         };
 626                 };
 627         };
 628         /* Interrupt line for the Cypress TMA140 touchscreen */
 629         touchscreen {
 630                 tma140_skomer_default: tma140_skomer {
 631                         skomer_cfg1 {
 632                                 pins = "GPIO218_AH11";
 633                                 ste,config = <&gpio_in_nopull>;
 634                         };
 635                 };
 636         };
 637 };
 638
 639 &ab8505_gpio {
 640         /* Hog a few default settings */
 641         pinctrl-names = "default";
 642         pinctrl-0 = <&gpio_default>;
 643
 644         gpio {
 645                 gpio_default: gpio_default {
 646                         skomer_mux {
 647                                 /* Change unused pins to GPIO mode */
 648                                 function = "gpio";
 649                                 groups = "gpio3_a_1",   /* default: SysClkReq4 */
 650                                          "gpio14_a_1";  /* default: PWMOut1 */
 651                         };
 652                         skomer_cfg1 {
 653                                 pins = "GPIO11_B17", "GPIO13_D17", "GPIO50_L4";
 654                                 bias-disable;
 655                         };
 656                 };
 657         };
 658 };