arch/arm/boot/dts/ste-ux500-samsung-skomer.dts

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * Devicetree for the Samsung XCover 2 GT-S7710 also known as Skomer.
   4  */
   5
   6 /dts-v1/;
   7 #include "ste-db8500.dtsi"
   8 #include "ste-ab8505.dtsi"
   9 #include "ste-dbx5x0-pinctrl.dtsi"
  10 #include <dt-bindings/gpio/gpio.h>
  11 #include <dt-bindings/leds/common.h>
  12 #include <dt-bindings/input/input.h>
  13 #include <dt-bindings/interrupt-controller/irq.h>
  14
  15 / {
  16         model = "Samsung XCover 2 (GT-S7710)";
  17         compatible = "samsung,skomer", "st-ericsson,u8500";
  18
  19         chosen {
  20                 stdout-path = &serial2;
  21         };
  22
  23         battery: battery {
  24                 compatible = "samsung,eb485159lu";
  25         };
  26
  27         /* TI TXS0206 level translator for 2.9 V */
  28         sd_level_translator: regulator-gpio {
  29                 compatible = "regulator-fixed";
  30
  31                 /* GPIO87 EN */
  32                 gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
  33                 enable-active-high;
  34
  35                 regulator-name = "sd-level-translator";
  36                 regulator-min-microvolt = <2900000>;
  37                 regulator-max-microvolt = <2900000>;
  38                 regulator-type = "voltage";
  39
  40                 startup-delay-us = <200>;
  41
  42                 pinctrl-names = "default";
  43                 pinctrl-0 = <&sd_level_translator_default>;
  44         };
  45
  46         /* External LDO MIC5366-3.3YMT for eMMC */
  47         ldo_3v3_reg: regulator-gpio-ldo-3v3 {
  48                 compatible = "regulator-fixed";
  49                 regulator-name = "en-3v3-fixed-supply";
  50                 regulator-min-microvolt = <3300000>;
  51                 regulator-max-microvolt = <3300000>;
  52                 gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>;
  53                 startup-delay-us = <5000>;
  54                 enable-active-high;
  55                 pinctrl-names = "default";
  56                 pinctrl-0 = <&emmc_ldo_en_default_mode>;
  57         };
  58
  59         wlan_en: regulator-gpio-wlan-en {
  60                 compatible = "regulator-fixed";
  61                 regulator-name = "wl-reg-on";
  62                 regulator-min-microvolt = <3000000>;
  63                 regulator-max-microvolt = <3000000>;
  64                 startup-delay-us = <200000>;
  65                 /* GPIO215 WLAN_EN */
  66                 gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
  67                 enable-active-high;
  68                 pinctrl-names = "default";
  69                 pinctrl-0 = <&wlan_en_default_mode>;
  70         };
  71
  72         vibrator {
  73                 compatible = "gpio-vibrator";
  74                 enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
  75                 pinctrl-names = "default";
  76                 pinctrl-0 = <&vibrator_default>;
  77         };
  78
  79         gpio-keys {
  80                 compatible = "gpio-keys";
  81                 pinctrl-names = "default";
  82                 pinctrl-0 = <&gpio_keys_default_mode>;
  83
  84                 button-home {
  85                         linux,code = <KEY_HOME>;
  86                         label = "HOME";
  87                         /* GPIO91 */
  88                         gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
  89                 };
  90                 button-volup {
  91                         linux,code = <KEY_VOLUMEUP>;
  92                         label = "VOL+";
  93                         /* GPIO67 */
  94                         gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
  95                 };
  96                 button-voldown {
  97                         linux,code = <KEY_VOLUMEDOWN>;
  98                         label = "VOL-";
  99                         /* GPIO92 */
 100                         gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
 101                 };
 102                 button-menu {
 103                         linux,code = <KEY_MENU>;
 104                         label = "MENU";
 105                         /* GPIO204 */
 106                         gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
 107                 };
 108                 button-back {
 109                         linux,code = <KEY_BACK>;
 110                         label = "BACK";
 111                         /* GPIO205 */
 112                         gpios = <&gpio6 13 GPIO_ACTIVE_LOW>;
 113                 };
 114         };
 115
 116         ktd253: backlight {
 117                 compatible = "kinetic,ktd253";
 118                 /* GPIO 69 */
 119                 enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
 120                 /* Default to 13/32 brightness */
 121                 default-brightness = <13>;
 122                 pinctrl-names = "default";
 123                 pinctrl-0 = <&gpio_backlight_default_mode>;
 124         };
 125
 126         /* Richtek RT8515GQW Flash LED Driver IC */
 127         flash {
 128                 compatible = "richtek,rt8515";
 129                 /* GPIO 140 */
 130                 enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
 131                 /* GPIO 141 */
 132                 ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
 133                 /*
 134                  * RFS is 16 kOhm and RTS is 100 kOhm giving
 135                  * the flash max current 343mA and torch max
 136                  * current 55 mA.
 137                  */
 138                 richtek,rfs-ohms = <16000>;
 139                 richtek,rts-ohms = <100000>;
 140                 pinctrl-names = "default";
 141                 pinctrl-0 = <&gpio_flash_default_mode>;
 142
 143                 led {
 144                         function = LED_FUNCTION_FLASH;
 145                         color = <LED_COLOR_ID_WHITE>;
 146                         flash-max-timeout-us = <250000>;
 147                         flash-max-microamp = <343750>;
 148                         led-max-microamp = <55000>;
 149                 };
 150         };
 151
 152         i2c-gpio-0 {
 153                 compatible = "i2c-gpio";
 154                 sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 155                 scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 156                 pinctrl-names = "default";
 157                 pinctrl-0 = <&i2c_gpio_0_default>;
 158                 #address-cells = <1>;
 159                 #size-cells = <0>;
 160                 /* TODO: this should be used by the NCP6914 Camera power management unit */
 161         };
 162
 163         i2c-gpio-1 {
 164                 compatible = "i2c-gpio";
 165                 sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 166                 scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 167                 pinctrl-names = "default";
 168                 pinctrl-0 = <&i2c_gpio_1_default>;
 169                 #address-cells = <1>;
 170                 #size-cells = <0>;
 171                 magnetometer@c {
 172                         compatible = "alps,hscdtd008a";
 173                         reg = <0x0c>;
 174                         avdd-supply = <&ab8500_ldo_aux1_reg>;
 175                         dvdd-supply = <&ab8500_ldo_aux8_reg>;
 176                 };
 177         };
 178
 179         soc {
 180                 // External Micro SD slot
 181                 mmc@80126000 {
 182                         arm,primecell-periphid = <0x10480180>;
 183                         max-frequency = <100000000>;
 184                         bus-width = <4>;
 185                         cap-sd-highspeed;
 186                         cap-mmc-highspeed;
 187                         /* All direction control is used */
 188                         st,sig-dir-cmd;
 189                         st,sig-dir-dat0;
 190                         st,sig-dir-dat2;
 191                         st,sig-dir-dat31;
 192                         st,sig-pin-fbclk;
 193                         full-pwr-cycle;
 194                         vmmc-supply = <&ab8500_ldo_aux3_reg>;
 195                         vqmmc-supply = <&sd_level_translator>;
 196                         pinctrl-names = "default", "sleep";
 197                         pinctrl-0 = <&mc0_a_1_default>;
 198                         pinctrl-1 = <&mc0_a_1_sleep>;
 199                         status = "okay";
 200                 };
 201
 202                 // WLAN SDIO channel
 203                 mmc@80118000 {
 204                         arm,primecell-periphid = <0x10480180>;
 205                         max-frequency = <50000000>;
 206                         bus-width = <4>;
 207                         non-removable;
 208                         cap-sd-highspeed;
 209                         vmmc-supply = <&wlan_en>;
 210                         pinctrl-names = "default", "sleep";
 211                         pinctrl-0 = <&mc1_a_2_default>;
 212                         pinctrl-1 = <&mc1_a_2_sleep>;
 213                         status = "okay";
 214                         #address-cells = <1>;
 215                         #size-cells = <0>;
 216
 217                         wifi@1 {
 218                                 compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
 219                                 reg = <1>;
 220                                 /* GPIO216 WL_HOST_WAKE */
 221                                 interrupt-parent = <&gpio6>;
 222                                 interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
 223                                 interrupt-names = "host-wake";
 224                                 pinctrl-names = "default";
 225                                 pinctrl-0 = <&wlan_default_mode>;
 226                         };
 227                 };
 228
 229                 /*
 230                  * eMMC seems to be mostly Samsung KLM4G1YE4C "4YMD1R"
 231                  */
 232                 mmc@80005000 {
 233                         arm,primecell-periphid = <0x10480180>;
 234                         max-frequency = <100000000>;
 235                         bus-width = <8>;
 236                         non-removable;
 237                         cap-mmc-highspeed;
 238                         mmc-ddr-1_8v;
 239                         no-sdio;
 240                         no-sd;
 241                         /* From datasheet page 26 figure 9: 300 ms set-up time for 4GB */
 242                         post-power-on-delay-ms = <300>;
 243                         vmmc-supply = <&ldo_3v3_reg>;
 244                         pinctrl-names = "default", "sleep";
 245                         pinctrl-0 = <&mc2_a_1_default>;
 246                         pinctrl-1 = <&mc2_a_1_sleep>;
 247
 248                         status = "okay";
 249                 };
 250
 251                 /* GBF (Bluetooth) UART */
 252                 uart@80120000 {
 253                         pinctrl-names = "default", "sleep";
 254                         pinctrl-0 = <&u0_a_1_default>;
 255                         pinctrl-1 = <&u0_a_1_sleep>;
 256                         status = "okay";
 257
 258                         /* FIXME: not quite working yet, probably needs regulators */
 259                         bluetooth {
 260                                 /* BCM4334B0 actually */
 261                                 compatible = "brcm,bcm4330-bt";
 262                                 shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
 263                                 device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
 264                                 host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
 265                                 pinctrl-names = "default";
 266                                 pinctrl-0 = <&bluetooth_default_mode>;
 267                         };
 268                 };
 269
 270                 /* GPF UART */
 271                 uart@80121000 {
 272                         status = "okay";
 273                         pinctrl-names = "default", "sleep";
 274                         pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
 275                         pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
 276                 };
 277
 278                 /* Debugging console UART connected to AB8505 USB */
 279                 uart@80007000 {
 280                         status = "okay";
 281                         pinctrl-names = "default", "sleep";
 282                         pinctrl-0 = <&u2rxtx_c_1_default>;
 283                         pinctrl-1 = <&u2rxtx_c_1_sleep>;
 284                 };
 285
 286                 prcmu@80157000 {
 287                         ab8505 {
 288                                 ab8500_usb {
 289                                         pinctrl-names = "default", "sleep";
 290                                         pinctrl-0 = <&usb_a_1_default>;
 291                                         pinctrl-1 = <&usb_a_1_sleep>;
 292                                 };
 293
 294                                 ab8505-regulators {
 295                                         ab8500_ldo_aux1 {
 296                                                 /* Used for VDD for sensors */
 297                                                 regulator-name = "AUX1";
 298                                                 regulator-min-microvolt = <3000000>;
 299                                                 regulator-max-microvolt = <3300000>;
 300                                         };
 301
 302                                         ab8500_ldo_aux2 {
 303                                                 /* Supplies the Cypress TMA140 touchscreen only with 3.0V */
 304                                                 regulator-name = "AUX2";
 305                                                 regulator-min-microvolt = <3000000>;
 306                                                 regulator-max-microvolt = <3000000>;
 307                                         };
 308
 309                                         ab8500_ldo_aux3 {
 310                                                 /* Used for voltage for external MMC/SD card */
 311                                                 regulator-name = "AUX3";
 312                                                 regulator-min-microvolt = <1100000>;
 313                                                 regulator-max-microvolt = <3300000>;
 314                                         };
 315
 316                                         ab8500_ldo_aux4 {
 317                                                 regulator-name = "AUX4";
 318                                                 /* Hammer to 3.0V for the display */
 319                                                 regulator-min-microvolt = <3000000>;
 320                                                 regulator-max-microvolt = <3000000>;
 321                                         };
 322
 323                                         ab8500_ldo_aux5 {
 324                                                 regulator-name = "AUX5";
 325                                                 /* Intended for 1V8 for touchscreen but actually left unused */
 326                                                 regulator-min-microvolt = <1050000>;
 327                                                 regulator-max-microvolt = <2790000>;
 328                                         };
 329
 330                                         ab8500_ldo_aux6 {
 331                                                 regulator-name = "AUX6";
 332                                                 /* Hammer to 1.8V for the display */
 333                                                 regulator-min-microvolt = <1800000>;
 334                                                 regulator-max-microvolt = <1800000>;
 335                                         };
 336
 337                                         ab8500_ldo_aux8 {
 338                                                 /* Mostly VIO for sensors */
 339                                                 regulator-name = "AUX8";
 340                                         };
 341                                 };
 342                         };
 343                 };
 344
 345                 /* I2C0 */
 346                 i2c@80004000 {
 347                         status = "okay";
 348
 349                         pinctrl-names = "default", "sleep";
 350                         pinctrl-0 = <&i2c0_a_1_default>;
 351                         pinctrl-1 = <&i2c0_a_1_sleep>;
 352
 353                         proximity@44 {
 354                                 compatible = "sharp,gp2ap002s00f";
 355                                 clock-frequency = <400000>;
 356                                 reg = <0x44>;
 357
 358                                 interrupt-parent = <&gpio4>;
 359                                 interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
 360                                 vdd-supply = <&ab8500_ldo_aux1_reg>;
 361                                 vio-supply = <&ab8500_ldo_aux8_reg>;
 362                                 pinctrl-names = "default";
 363                                 pinctrl-0 = <&gp2ap002_skomer_default>;
 364                                 sharp,proximity-far-hysteresis = /bits/ 8 <0x2f>;
 365                                 sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>;
 366                         };
 367                 };
 368
 369
 370                 /* I2C2 */
 371                 i2c@80128000 {
 372                         status = "okay";
 373
 374                         pinctrl-names = "default", "sleep";
 375                         pinctrl-0 = <&i2c2_b_2_default>;
 376                         pinctrl-1 = <&i2c2_b_2_sleep>;
 377
 378                         accel@18 {
 379                                 compatible = "bosch,bma254";
 380                                 clock-frequency = <400000>;
 381                                 reg = <0x18>;
 382
 383                                 /* GPIO224 used as "smart alert" interrupt */
 384                                 interrupt-parent = <&gpio7>;
 385                                 interrupts = <0 IRQ_TYPE_EDGE_RISING>;
 386
 387                                 mount-matrix = "0", "-1", "0",
 388                                               "1", "0", "0",
 389                                                "0", "0", "1";
 390                                 vdd-supply = <&ab8500_ldo_aux1_reg>;
 391                                 vddio-supply = <&ab8500_ldo_aux8_reg>;
 392                                 pinctrl-names = "default";
 393                                 pinctrl-0 = <&bma254_skomer_default>;
 394                         };
 395                 };
 396
 397                 /* I2C3 */
 398                 i2c@80110000 {
 399                         status = "okay";
 400
 401                         pinctrl-names = "default", "sleep";
 402                         pinctrl-0 = <&i2c3_c_2_default>;
 403                         pinctrl-1 = <&i2c3_c_2_sleep>;
 404
 405                         /* Cypress CY8CTMA140 touchscreen */
 406                         touchscreen@20 {
 407                                 compatible = "cypress,cy8ctma140";
 408                                 clock-frequency = <400000>;
 409                                 reg = <0x20>;
 410
 411                                 touchscreen-size-x = <480>;
 412                                 touchscreen-size-y = <800>;
 413                                 touchscreen-max-pressure = <255>;
 414
 415                                 /* GPIO218 for IRQ */
 416                                 interrupt-parent = <&gpio6>;
 417                                 interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
 418
 419                                 /* VDD is "digital supply" nominally 1.71-3.6V */
 420                                 vdd-supply = <&ab8500_ldo_aux2_reg>;
 421                                 /* VCPIN is "analog supply", 2.7-3.6 V */
 422                                 vcpin-supply = <&ab8500_ldo_aux2_reg>;
 423
 424                                 pinctrl-names = "default";
 425                                 pinctrl-0 = <&tma140_skomer_default>;
 426                         };
 427                 };
 428
 429                 mcde@a0350000 {
 430                         status = "okay";
 431                         pinctrl-names = "default";
 432                         pinctrl-0 = <&dsi_default_mode>;
 433
 434                         dsi@a0351000 {
 435                                 panel {
 436                                         /* NT35510-based Hydis HVA40WV1 */
 437                                         compatible = "hydis,hva40wv1", "novatek,nt35510";
 438                                         reg = <0>;
 439                                         /* v_lcd_3v0 2.3-4.8V */
 440                                         vdd-supply = <&ab8500_ldo_aux4_reg>;
 441                                         /* v_lcd_1v8 1.65-3.3V */
 442                                         vddi-supply = <&ab8500_ldo_aux6_reg>;
 443                                         /* GPIO 139 */
 444                                         reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
 445                                         pinctrl-names = "default";
 446                                         pinctrl-0 = <&display_default_mode>;
 447                                         backlight = <&ktd253>;
 448                                 };
 449                         };
 450                 };
 451         };
 452 };
 453
 454 &pinctrl {
 455         sdi0 {
 456                 mc0_a_1_default {
 457                         default_cfg1 {
 458                                 /* GPIO18, 19 & 20 unused so pull down */
 459                                 ste,config = <&gpio_in_pd>;
 460                         };
 461                 };
 462         };
 463
 464         /* This is a reset line for the eMMC */
 465         sdi2 {
 466                 mc2_a_1_default {
 467                         default_cfg2 {
 468                                 pins = "GPIO130_C8"; /* FBCLK */
 469                                 ste,config = <&gpio_in_pd>;
 470                         };
 471                 };
 472         };
 473
 474         mcde {
 475                 dsi_default_mode: dsi_default {
 476                         default_mux1 {
 477                                 /* Mux in VSI0 used for DSI TE */
 478                                 function = "lcd";
 479                                 groups = "lcdvsi0_a_1"; /* VSI0 for LCD */
 480                         };
 481                         default_cfg1 {
 482                                 pins = "GPIO68_E1"; /* VSI0 */
 483                                 ste,config = <&in_nopull>;
 484                         };
 485                 };
 486         };
 487
 488         /* Two GPIO lines used by the display */
 489         display {
 490                 display_default_mode: display_default {
 491                         skomer_cfg1 {
 492                                 /*
 493                                  * OLED DETECT or check_pba, this appears to be high
 494                                  * on "PBA" which I guess is "prototype board A".
 495                                  */
 496                                 pins = "GPIO93_B7";
 497                                 ste,config = <&gpio_in_nopull>;
 498                         };
 499                         skomer_cfg2 {
 500                                 pins = "GPIO139_C9";
 501                                 /*
 502                                  * MIPI_DSI0_RESET_N resets the display, leave high
 503                                  * (de-asserted) so we only assert reset explicitly
 504                                  * from the display driver.
 505                                  */
 506                                 ste,config = <&gpio_out_hi>;
 507                         };
 508                 };
 509         };
 510         backlight {
 511                 gpio_backlight_default_mode: backlight_default {
 512                         skomer_cfg1 {
 513                                 pins = "GPIO69_E2"; /* LCD_BL_CTRL */
 514                                 ste,config = <&gpio_out_lo>;
 515                         };
 516                 };
 517         };
 518         flash {
 519                 gpio_flash_default_mode: flash_default {
 520                         skomer_cfg1 {
 521                                 pins = "GPIO140_B11", "GPIO141_C12";
 522                                 ste,config = <&gpio_out_lo>;
 523                         };
 524                 };
 525         };
 526         /* GPIO that enables the 2.9V SD card level translator */
 527         sd-level-translator {
 528                 sd_level_translator_default: sd_level_translator_default {
 529                         /* level shifter on GPIO87 */
 530                         skomer_cfg1 {
 531                                 pins = "GPIO87_B3";
 532                                 ste,config = <&gpio_out_hi>;
 533                         };
 534                 };
 535         };
 536         /* GPIO that enables the LDO regulator for the eMMC */
 537         emmc-ldo {
 538                 emmc_ldo_en_default_mode: emmc_ldo_default {
 539                         /* LDO enable on GPIO223 */
 540                         skomer_cfg1 {
 541                                 pins = "GPIO223_AH9";
 542                                 ste,config = <&gpio_out_hi>;
 543                         };
 544                 };
 545         };
 546         /* GPIO keys */
 547         gpio-keys {
 548                 gpio_keys_default_mode: gpio_keys_default {
 549                         skomer_cfg1 {
 550                                 pins = "GPIO67_G2", /* VOL UP */
 551                                        "GPIO91_B6", /* HOME */
 552                                        "GPIO92_D6", /* VOL DOWN */
 553                                        "GPIO204_AF23", /* MENU */
 554                                        "GPIO205_AG23"; /* BACK */
 555                                         ste,config = <&gpio_in_pu>;
 556                         };
 557                 };
 558         };
 559         /* Interrupt line for BMA254 */
 560         bma254 {
 561                 bma254_skomer_default: bma254_skomer {
 562                         skomer_cfg1 {
 563                                 pins = "GPIO224_AG9";
 564                                 ste,config = <&gpio_in_pd>;
 565                         };
 566                 };
 567         };
 568         /* Interrupt line for light/proximity sensor GP2AP002 */
 569         gp2ap002 {
 570                 gp2ap002_skomer_default: gp2ap002_skomer {
 571                         skomer_cfg1 {
 572                                 pins = "GPIO146_D13";
 573                                 ste,config = <&gpio_in_nopull>;
 574                         };
 575                 };
 576         };
 577         /* GPIO-based I2C bus for NCP6914 */
 578         i2c-gpio-0 {
 579                 i2c_gpio_0_default: i2c_gpio_0 {
 580                         skomer_cfg1 {
 581                                 pins = "GPIO143_D12", "GPIO144_B13";
 582                                 ste,config = <&gpio_in_nopull>;
 583                         };
 584                 };
 585         };
 586         /* GPIO-based I2C bus for ALPS HSCD compass */
 587         i2c-gpio-1 {
 588                 i2c_gpio_1_default: i2c_gpio_1 {
 589                         skomer_cfg1 {
 590                                 pins = "GPIO151_B17", "GPIO152_D16";
 591                                 ste,config = <&gpio_in_nopull>;
 592                         };
 593                 };
 594         };
 595         wlan {
 596                 wlan_default_mode: wlan_default {
 597                         skomer_cfg1 {
 598                                 pins = "GPIO216_AG12";
 599                                 ste,config = <&gpio_in_pd>;
 600                         };
 601                 };
 602                 wlan_en_default_mode: wlan_en_default {
 603                         skomer_cfg2 {
 604                                 pins = "GPIO215_AH13";
 605                                 ste,config = <&gpio_out_lo>;
 606                         };
 607                 };
 608         };
 609         bluetooth {
 610                 bluetooth_default_mode: bluetooth_default {
 611                         skomer_cfg1 {
 612                                 pins = "GPIO199_AH23", "GPIO222_AJ9";
 613                                 ste,config = <&gpio_out_lo>;
 614                         };
 615                         skomer_cfg2 {
 616                                 pins = "GPIO97_D9";
 617                                 ste,config = <&gpio_in_nopull>;
 618                         };
 619                 };
 620         };
 621         vibrator {
 622                 vibrator_default: vibrator_default {
 623                         skomer_cfg1 {
 624                                 pins = "GPIO195_AG28";  /* MOT_EN */
 625                                 ste,config = <&gpio_out_lo>;
 626                         };
 627                 };
 628         };
 629         /* Interrupt line for the Cypress TMA140 touchscreen */
 630         touchscreen {
 631                 tma140_skomer_default: tma140_skomer {
 632                         skomer_cfg1 {
 633                                 pins = "GPIO218_AH11";
 634                                 ste,config = <&gpio_in_nopull>;
 635                         };
 636                 };
 637         };
 638 };
 639
 640 &ab8505_gpio {
 641         /* Hog a few default settings */
 642         pinctrl-names = "default";
 643         pinctrl-0 = <&gpio_default>;
 644
 645         gpio {
 646                 gpio_default: gpio_default {
 647                         skomer_mux {
 648                                 /* Change unused pins to GPIO mode */
 649                                 function = "gpio";
 650                                 groups = "gpio3_a_1",   /* default: SysClkReq4 */
 651                                          "gpio14_a_1";  /* default: PWMOut1 */
 652                         };
 653                         skomer_cfg1 {
 654                                 pins = "GPIO11_B17", "GPIO13_D17", "GPIO50_L4";
 655                                 bias-disable;
 656                         };
 657                 };
 658         };
 659 };